| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Update the Integrator defconfig with some sensible defaults:
- Compile a combined image supporting Integrator/AP and
Integrator/CP, with the core modules CM720, CM920, CM922,
CM926, CM1020, CM1022 and CM1026 in a single image, this
works just fine and gives some nice compilation coverage
- NOHZ (tickless) and HRTIMERS turned on
- Compile using EABI, let's assume recent compilers are used
now (tested using GCC 4.4.1)
- Remove forced 32MiB at command line, the bootloader usually
knows this better, and my U-Boot patches nowadays make that
boot loader pass the correct adjusted value
- Enable the MTD Physmap flash driver, so that the changes done
earlier by Marc Zyngier replacing integrator-flash takes
effect
- Enable the PL030 RTC driver that has not been default-compiled
with any config for a while
This has been tested on the real hardware Integrator AP with
both an ARM920T and ARM926EJ-S core module.
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/devel' of ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (128 commits)
ARM: S5P64X0: External Interrupt Support
ARM: EXYNOS4: Enable MFC on Samsung NURI
ARM: EXYNOS4: Enable MFC on universal_c210
ARM: S5PV210: Enable MFC on Goni
ARM: S5P: Add support for MFC device
ARM: EXYNOS4: Add support FIMD on SMDKC210
ARM: EXYNOS4: Add platform device and helper functions for FIMD
ARM: EXYNOS4: Add resource definition for FIMD
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: SAMSUNG: Add IRQ_I2S0 definition
ARM: SAMSUNG: Add platform device for idma
ARM: EXYNOS4: Add more registers to be saved and restored for PM
ARM: EXYNOS4: Add more register addresses of CMU
ARM: EXYNOS4: Add platform device for dwmci driver
ARM: EXYNOS4: configure rtc-s3c on NURI
ARM: EXYNOS4: configure MAX8903 secondary charger on NURI
ARM: EXYNOS4: configure ADC on NURI
ARM: EXYNOS4: configure MAX17042 fuel gauge on NURI
ARM: EXYNOS4: configure regulators and PMIC(MAX8997) on NURI
ARM: EXYNOS4: Increase NR_IRQS for devices with more IRQs
...
Fix up tons of silly conflicts:
- arch/arm/mach-davinci/include/mach/psc.h
- arch/arm/mach-exynos4/Kconfig
- arch/arm/mach-exynos4/mach-smdkc210.c
- arch/arm/mach-exynos4/pm.c
- arch/arm/mach-imx/mm-imx1.c
- arch/arm/mach-imx/mm-imx21.c
- arch/arm/mach-imx/mm-imx25.c
- arch/arm/mach-imx/mm-imx27.c
- arch/arm/mach-imx/mm-imx31.c
- arch/arm/mach-imx/mm-imx35.c
- arch/arm/mach-mx5/mm.c
- arch/arm/mach-s5pv210/mach-goni.c
- arch/arm/mm/Kconfig
|
|
git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/deletion' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: mach-loki: delete
ARM: mach-s3c2400: delete
ARM: mach-s3c24a0: delete
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
ARM: S3C24XX: Use generic s3c_set_platdata for devices
ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
ARM: SAMSUNG: Use generic s3c_set_platdata for FB
ARM: SAMSUNG: Use generic s3c_set_platdata for TS
ARM: S3C64XX: Add PWM backlight support on SMDK6410
ARM: S5P64X0: Add PWM backlight support on SMDK6450
ARM: S5P64X0: Add PWM backlight support on SMDK6440
ARM: S5PC100: Add PWM backlight support on SMDKC100
ARM: S5PV210: Add PWM backlight support on SMDKV210
ARM: EXYNOS4: Add PWM backlight support on SMDKC210
ARM: EXYNOS4: Add PWM backlight support on SMDKV310
ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
...
Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
|
|
1. support brownstone
2. support mmc
3. support basic filesystem and language
4. remove dynamic_debug, since too many log during access sd
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This was introduced more than 3 years ago, and since then only generic
janitorial changes were made without further addition of actual support
for "real" devices. This is therefore a cost with no benefits to keep
in the tree. If someone wishes to revive this code, it is always
possible to retrieve it from the Git repository.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
CC: Ke Wei <kewei@marvell.com>
CC: Saeed Bishara <saeed@marvell.com>
CC: Lennert Buytenhek <buytenh@wantstofly.org>
|
|
'lpc32xx/devel', 'pxa/devel', 'tegra/devel' and 'stericsson/master' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc into next/devel
|
|
'pxa/cleanup' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc into next/cleanup
|
|
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The patch adds following configurations to enable build of mx23evk
and mx28evk in defconfig.
CONFIG_MACH_MX23EVK
CONFIG_MACH_MX28EVK
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Let USB Storage be built by default.
Also select NLS_ISO8859 so that the USB device can be mounted.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The patch fixes the warning below.
arch/arm/configs/mxs_defconfig:92:warning: symbol value 'm' invalid for RTC_CLASS
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Adds defconfig entries needed to boot a single ux500 kernel
on the Snowball board.
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
|
|
Activate the new USB stuff so we atleast get some compile
coverage for this stuff.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
RTC_CLASS is changed to bool, so 'm' is invalid.
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
ARM: 6945/1: Add unwinding support for division functions
ARM: kill pmd_off()
ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks
ARM: 6943/1: mm: use TTBR1 instead of reserved context ID
ARM: 6942/1: mm: make TTBR1 always point to swapper_pg_dir on ARMv6/7
ARM: 6941/1: cache: ensure MVA is cacheline aligned in flush_kern_dcache_area
ARM: add sendmmsg syscall
ARM: 6863/1: allow hotplug on msm
ARM: 6832/1: mmci: support for ST-Ericsson db8500v2
ARM: 6830/1: mach-ux500: force PrimeCell revisions
ARM: 6829/1: amba: make hardcoded periphid override hardware
ARM: 6828/1: mach-ux500: delete SSP PrimeCell ID
ARM: 6827/1: mach-netx: delete hardcoded periphid
ARM: 6940/1: fiq: Briefly document driver responsibilities for suspend/resume
ARM: 6938/1: fiq: Refactor {get,set}_fiq_regs() for Thumb-2
ARM: 6914/1: sparsemem: fix highmem detection when using SPARSEMEM
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM
at91: drop at572d940hf support
at91rm9200: introduce at91rm9200_set_type to specficy cpu package
at91: drop boot_params and PLAT_PHYS_OFFSET
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
OMAP3: PM: Boot message is not an error, and not helpful, remove it
OMAP3: cpuidle: change the power domains modes determination logic
OMAP3: cpuidle: code rework for improved readability
OMAP3: cpuidle: re-organize the C-states data
OMAP3: clean-up mach specific cpuidle data structures
OMAP3 cpuidle: remove useless SDP specific timings
usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
usb: otg: OMAP4430: Fixing the omap4430_phy_init function
usb: musb: am35x: fix compile error when building am35x
usb: musb: OMAP4430: Power down the PHY during board init
omap: drop board-igep0030.c
omap: igep0020: add support for IGEP3
omap: igep0020: minor refactoring
omap: igep0020: name refactoring for future merge with IGEP3
omap: Remove support for omap2evm
arm: omap2plus: GPIO cleanup
omap: musb: introduce default board config
omap: move detection of NAND CS to common-board-devices
omap: use common initialization for PMIC i2c bus
omap: consolidate touch screen initialization among different boards
...
|
|
devel-stable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into devel-stable
Conflicts:
arch/arm/Kconfig
arch/arm/mach-exynos4/mach-nuri.c
|
|
no-one use it and it's nearly impossible get a board to work on it
and the Mainline implementation was never finished
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
|
|
and update it with ubi, sound, nfs support etc...
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Tested on at91sam9263ek
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Grégory Hermant <gregory.hermant@calao-systems.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Conflicts:
arch/arm/Kconfig
arch/arm/mach-ns9xxx/include/mach/uncompress.h
|
|
and 'spear' into for-linus
|
|
'consolidate-generic', 'consolidate-smp', 'consolidate-stmp' and 'consolidate-zones' into consolidate
|
|
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We only need one defconfig for SPEAr3xx now since we can build all
three boards into one kernel.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Tested on a PB11-MPCore.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
devel-stable
|
|
APF9328 is an i.MXL based SOM (System On Module) that can be plugged on
several docking/development boards. Here only basic module support
is added (Ethernet, Serial, NOR Flash).
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Nicolas Colombain <nicolas.colombain@armadeus.com>
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The two SoCs have different PHYS_OFFSETs so it's not (yet) possible to
compile a single (working) kernel for these.
LAKML-Reference: 1302464943-20721-4-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
|
|
This patch adds MACH_ARMLEX4210 and MACH_NURI in exynos4_defconfig.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Re-generate defconfig for Marvell Dove platform
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Disabled legacy support for ARMv6 architecture on Dove platform.
Latest Dove HW uses only ARMv7 model.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
After commit ffb63e3 (omap2/3/4: Select all omaps and boards by default)
many explicit settings can be dropped from the defconfig.
This shrinks it down a bit more and makes it easier
to patch later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This mach has not seen any updates since the initial inclusion besides
generic cleanup. Furthermore:
- The i.MX23 covered in mach-mxs is just a renamed version of the
STMP378x.
- mach-stmp378x has a lot of reinvented interfaces, leaking all sorts of
mach-related includes into the drivers. One example is the dmaengine
which does not use the linux dmaengine-API but some privately exported
symbols. So drivers cannot be reused. mach-mxs does it better.
- There is only one board defined (which I couldn't find any trace of
despite being a development board). It has been converted to
mach-mxs in a previous patch.
Since the only user of this mach was converted, it means that
mach-stmp378x can go.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This mach has not seen any updates since the initial inclusion besides
generic cleanup. Furthermore:
- It has a lot of reinvented interfaces, leaking all sorts of
mach-related includes into the drivers. One example is the dmaengine
which does not use the linux dmaengine-API but some privately exported
symbols. So, drivers cannot be reused. mach-mxs is very similar and
does it better.
- It can be doubted that this worked at all. Check the DMA routines in
stmp37xx.c for copy/paste bugs. A lot of APBX-related stuff is
actually writing into registers for APBH.
- There is only one board defined (which I couldn't find any trace of
despite being a development board). In this board, only two devices
have resources, the debug uart and the application uart. Neither of
those have the needed custom drivers merged (and never will). debug
uart is amba-pl011 which has an in-kernel driver without the
mach-specific-stuff. appuart has a driver which was introduced for
mach-mxs, and this one is reusable for a properly done mach.
So, this single board registers only unsupported devices and the
generic code looks suspicious and has poor design. Delete this
stuff. If there is interest, it is wiser to restart using
mach-mxs.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Covers MX23, MX28 and STMP378x.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The port is actually unmaintained and only received global
cleanups and a few build fixes since mid 2008.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
A minimal defconfig for build testing the AT91x40 SoC.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
* 'for-linus' of git://android.git.kernel.org/kernel/tegra:
ARM: tegra: harmony: initialize the TPS65862 PMIC
ARM: tegra: update defconfig
ARM: tegra: harmony: update PCI-e initialization sequence
ARM: tegra: trimslice: enable MMC/SD slots
ARM: tegra: enable new drivers in defconfig
ARM: tegra: Add Toshiba AC100 support
ARM: tegra: harmony: Set WM8903 gpio_base
ARM: tegra: harmony: I2C-related portions of audio support
ARM: tegra: harmony: register i2c devices
ARM: tegra: seaboard: register i2c devices
ARM: tegra: harmony: Beginnings of audio support
ARM: tegra: create defines for SD-related GPIO names
ARM: tegra: add devices.c entries for audio
|
|
Conflicts:
arch/arm/mach-omap2/board-overo.c
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
|
|
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
|
