| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add the device-tree node for the GK20A GPU and leave it disabled.
It is the responsibility of the bootloader to enable it if the
VPR registers have been programmed such that the GPU can operate.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
|
|
The VDD_LED supply's output is a fixed 3.3 V. Record that in the min-
and max-microvolt properties.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
eMMC is soldered on to the board, and as such isn't removable. Mark it
as non-removable so that operating systems can treat it appropriately.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
There are general changes pending to make the /aliases/serial* entries
number the serial ports on the system. On Tegra, so far the ports have
been just numbered dynamically as they are configured so that makes them
change.
To avoid this, add specific aliases per board to keep the old numbers.
This allows us to change the numbering by default on future SoCs while
keeping the numbering on existing boards.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The defined mechanism for programming the Tegra pinmux is to perform all
of the following at once in order, before using any I/O controller that
is affected by the pinmux:
- Set the CLAMP_INPUTS_WHEN_TRISTATED PMC register bit.
- Set up any GPIO pins to their "initial" state.
- Program all pinmux settings in one go.
Other methods such as:
- Not setting CLAMP_INPUTS_WHEN_TRISTATED.
- Not setting GPIOs to their "initial" state before programming the
pinmux settings of the related pin, in particular the mux function.
- Not programming the entire pinmux at once, in order to avoid
possible conflicting settings.
... are not qualified or supported by NVIDIA ASIC/syseng. They could
cause glitches or undesired output levels on some pins, or controller
malfunction.
While we've been getting away with doing something different on many
Tegra boards without issue, I believe we've just been getting lucky.
I'd like to switch all Tegra124 systems to the correct scheme now so
they provide the right example to follow, and require that any new
boards we support upstream work in the same fashion.
While it would be nice to update boards containing older SoCs for
consistency, I don't anticipate doing so. It's too much churn to change
at this time. At least with all Tegra124 boards converted, the most
recent boards provide the correct example.
Since the bootloader needs to reprogram the pinmux to access certain
peripherals, it must program the entire pinmux due to the supported
rules above. As such, there is no need to program any part of the pinmux
from the kernel, unless dynamic pinmuxing is used. Given this, we couuld
simply remove the pinmux "default" state from the DT entirely. However,
some bootloaders parse the DT to perform their initial pinmux setup, so
it's useful to keep the pinmux data in DT. To allow this while avoiding
redundant work in the kernel, rename the "default" state to "boot". The
kernel won't apply this, but bootloaders can still look for this state
name and apply it. Note however that the DT provides zero information
about the required initial GPIO setup, so bootloaders using this approach
are not likely to operate correctly without an additional GPIO
initialization table somewhere. Previous discussions on the DT mailing
list have rejected adding such a table to DT...
The following U-Boot commits fully initialize the pinmux:
Jetson TK1: 4ff213b8e478 ARM: tegra: clamp inputs on Jetson TK1
Venice2: 3365479ce78a ARM: tegra: Venice2 pinmux spreadsheet updates
Both are part of U-Boot v2014.07 and later.
Without those commits, the only fallout I see from this change is that
HDMI on Venice2 no longer works. Given the very small user-base of this
platform, I feel that requiring a bootloader update is reasonable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
These labels will be used by other boards in addition to Venice2, move
them to tegra124.dtsi so they are defined in a common place.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Venice2 contains an Atmel MXT touchpad. Add an I2C node for it to DT.
The Linux driver doesn't quite work on this platform yet, but adding
the DT node causes no issues, and will allow the device to work once
the driver is fixed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The property for enabling external rail control on the AS3722 is
ams,ext-control, not ams,external-control. Since the external rail
control property was previously being ignored, LP1 suspend on these
boards wasn't actually turning the CPU rail off at all.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Turn on the HDA controller in Venice2, it is used for HDMI audio.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This adds the EC i2c tunnel (and devices under it) to the
tegra124-venice2 device tree.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Venice2 can detect write-protect on the SD card. Add the required
DT entries to allow this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[swarren: fixed GPIO polarity per Thierry's testing]
Tested-by: Thierry Reding <treding@nvidia.com>
|
|
Add HDMI +5V, VDD and PLL regulators and enable the DDC I2C controller.
Enable the HDMI device, provide the power supplies as well as the DDC
adapter and use the standard pin (PN7) for hotplug detection.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
VDDIO_SDMMC3 is the VQMMC (I/O) supply, not the VMMC (core) supply,
for the SD slot on Venice2.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This regulator supplies power to pretty much everything on the board, so
it doesn't make sense to allow it to turn off. Mark it boot-on and
always-on so it doesn't get turned off. Without this, I see issues with
the eMMC device; it can't be correctly detected during boot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
|
|
Neither Tegra114 nor Tegra124 allow "low power mode" to be configured
on SDIO1 or SDIO3 drive groups. Remove the attempt to configure that
option from the Dalmore and Venice2 DTs.
The Venice2 DT contained duplicate configurations for most sdmmc1_*
pins. Remove the duplicate pins from one of the nodes, and fix the
configuration since the remaining clk pin is output-only.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Tegra124 can support 4GB of RAM. With that much RAM (plus some memory-
mapped IO peripherals), more than 32-bits of physical address space is
required. Hence, convert all Tegra124 DTs to use 2 DT cells for address
space.
(I think this was suggested by Olof Johansson, but I'm not 100% sure)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Device tree node name should reflect the kind of device rather than the
specific name of the device.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Equal signs should always be preceded and followed by a single space in
device tree files.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
USB1 and USB3 are routed to two external connectors, while USB2 is used
for the integrated webcam.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Venice2 has a 12.9" (2560x1700) panel connected to the eDP output of the
Tegra124. The panel has an EDID to describe the video timings but needs
a few extra nodes to get the backlight to come up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The SDMMC3 interface is supplied with 1.8V by the PMICs LDO6.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Some of the regulators and the relationships to other regulators are
wrong. This commit attempts to rectify this by making them more similar
to what the schematics contain. This starts by adding a +VDD_MUX supply
that represents the 12V input and derives the main +3.3V_SYS and +5V_SYS
supplies from that. The majority of the other regulators derive from one
of those three.
While at it, rename the regulators to match the names in the schematics
to make them easier to match up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Both USB_VBUS_EN0 and USB_VBUS_EN1 are configured the same way, so they
can be combined into a single node. While at it, don't configure them as
pull-up since they already have external pull-ups. Also U-Boot doesn't
configure them as pull-up either.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Venice2 contains an SPI Flash chip, which contains the bootloader.
Add this to the DT, so the kernel can access it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Add system-power-controller property to system PMIC, ams AS3722,
node to enable power off functionality through PMIC.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Contrary to the rest of the keyboard, which is connected to the ChromeOS
embedded controller, the power key is hooked up to a GPIO. Add a device
tree node to handle it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The keyboard on Venice2 is attached to the ChromeOS embedded controller.
Add the corresponding device tree nodes and use the MATRIX_KEY define to
encode keycodes.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This ensures that the PMIC RTC provides the system time, rather than
the on-SoC RTC, which is not battery-backed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Add ams AS3722 entry for gpio/pincontrol and regulators
to venice2 DT.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Compare the initial population of default pinmux configuration of Venice2
with the chrome branch and add/fix the missing configurations.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This pin needs to be configured in pull-down, non-tristate mode in order
for the backlight to work correctly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Other boards use PULL_NONE for their debug UART pins, and without this
change, the board doesn't accept any serial input.
Don't set the I2S port pins to tristate mode, or no audio signal will
be sent out.
Fixes: 605ae5804385 ("ARM: tegra: add default pinctrl nodes for Venice2")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Add the default pinmux configuration for the Tegra124 based
Venice2 platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Subsequent patches will need to reference a PWM channel for backlight
support, so enable the PWM device and assign a label to it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Venice2 uses the MAX98090 audio CODEC, and supports built-in speakers,
and a combo headphones/microphone jack. Add a top-level sound card node
to represent this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Enable all the I2C controllers that are wired up on Venice2. I don't
know the correct I2C bus clock rates, so set them all to a conservative
100KHz for now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Tegra124 has 4 MMC controllers just like previous versions of the SoC.
Note that there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW.
Also enable the relevant controllers in the Venice2 board DT.
power-gpios property suggested by Thierry Reding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
|
|
This patch adds clock properties for devices in the DT for basic support
of Tegra124 SoC.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren, added missing unit address to "clock" node]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Enable LP1 suspend mode for Tegra124 Venice2 board.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Add support for the Tegra124 based Venice2 reference board.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
