| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
reset-gpios is more clear than rst-gpio.
This change has been done as one atomic commit but it
does breaks compatability with older dtbs.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch adds in the required DT node for the c8sectpfe
Linux DVB demux driver which allows the tsin channels
to be used on an upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Adding these properties makes the I2C bus to the demodulators much
more reliable, and we no longer suffer from I2C errors when tuning.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
These boards are mounted with Realtek RTL8367 switch.
We consider the bootloader will have intiliazed the switch before jumping into
the kernel, so we declare it as a fixed link.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The PWM may not be used on some boards, so enable them only the board file.
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The USB3 controller is present on both variants of the b2120 board so
enable the controller in the generic stihxxx-b2120.dtsi file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The nodes have been split to allow as much commonality as possible.
The stih407 has a silicon bug with eMMC UHS modes (with top regs)
and as such doesn't have any of the uhs dt properties.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The MiPHY28lp is a Generic PHY which can serve various SATA, PCIe or
USB3 devices. The two first ports can be use for either; both SATA, both
PCIe or one of each in any configuration.
The Third port is only for USB3.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
This patch adds the DRM/KMS dt nodes.
This node can't be in stih407-family.dtsi file because in the future we
will integrate a new stih418-b2199 board. It's a stih407 family board
with different drm/kms dt nodes.
That is why i created the stih407.dtsi file.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The stih410 soc which will be added in the following commit is very similar to
the stih407, to enable maximum re-use of the dt files this commit abstracts the
common parts into a shared dt file stihxxx-b2120 for the board, and also a shared
file stih407-family.dtsi for the SoC.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
