| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Connections may be cleanup while waiting for the commands to complete so
this attempts to check if the connection handle remains valid in case of
errors that would lead to call hci_conn_failed:
BUG: KASAN: slab-use-after-free in hci_conn_failed+0x1f/0x160
Read of size 8 at addr ffff888001376958 by task kworker/u3:0/52
CPU: 0 PID: 52 Comm: kworker/u3:0 Not tainted
6.5.0-rc1-00527-g2dfe76d58d3a #5615
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
1.16.2-1.fc38 04/01/2014
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
<TASK>
dump_stack_lvl+0x1d/0x70
print_report+0xce/0x620
? __virt_addr_valid+0xd4/0x150
? hci_conn_failed+0x1f/0x160
kasan_report+0xd1/0x100
? hci_conn_failed+0x1f/0x160
hci_conn_failed+0x1f/0x160
hci_abort_conn_sync+0x237/0x360
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When sending HCI_OP_CREATE_CONN_CANCEL it shall Wait for
HCI_EV_CONN_COMPLETE, not HCI_EV_CMD_STATUS, when the reason is
anything but HCI_ERROR_REMOTE_POWER_OFF. This reason is used when
suspending or powering off, where we don't want to wait for the peer's
response.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Dropped CIS that are in state BT_OPEN/BT_BOUND, and in state BT_CONNECT
with HCI_CONN_CREATE_CIS unset, should be cleaned up immediately.
Closing CIS ISO sockets should result to the hci_conn be deleted, so
that potentially pending CIG removal can run.
hci_abort_conn cannot refer to them by handle, since their handle is
still unset if Set CIG Parameters has not yet completed.
This fixes CIS not being terminated if the socket is shut down
immediately after connection, so that the hci_abort_conn runs before Set
CIG Parameters completes. See new BlueZ test "ISO Connect Close - Success"
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Calling hci_conn_del in __iso_sock_close is invalid. It needs
hdev->lock, but it cannot be acquired there due to lock ordering.
Fix this by doing cleanup via hci_conn_drop.
Return hci_conn with refcount 1 from hci_bind_cis and hci_connect_cis,
so that the iso_conn always holds one reference. This also fixes
refcounting when error handling.
Since hci_conn_abort shall handle termination of connections in any
state properly, we can handle BT_CONNECT socket state in the same way as
BT_CONNECTED.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This is introduced in commit 903e45411099 but was never implemented.
Fixes: 903e45411099 ("Bluetooth: AMP: Use HCI cmd to Read Loc AMP Assoc")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btusb_recv_event_intel is specific to Intel controllers therefore it
shall be placed inside btintel.c so btusb don't have a mix of vendor
specific code with the generic parts.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add support for the Bluetooth chip codenamed APACHE which is part of
WCN3988.
The firmware for this chip has a slightly different naming scheme
compared to most others. For ROM Version 0x0200 we need to use
apbtfw10.tlv + apnv10.bin and for ROM version 0x201 apbtfw11.tlv +
apnv11.bin
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the compatible for the Bluetooth part of the Qualcomm WCN3988
chipset.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds support for NXP AW693 chipset in btnxpuart driver
by adding FW name and bootloader signature. Based on the
loader version bits 7:6 of the bootloader signature, the
driver can choose between selecting secure and non-secure
FW files.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
in nokia_bluetooth_serdev_probe(), check the return value of
clk_prepare_enable() and return the error code if
clk_prepare_enable() returns an unexpected value.
Fixes: 7bb318680e86 ("Bluetooth: add nokia driver")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The BCM43430A1 has a default MAC address of AA:AA:AA:AA:AA:AA.
Although, unlike some other entries, this does not include the
chip name, it is clearly not a real address. This was found in
AzureWave AW-NB197SM and AW-NM372SM modules.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds support for BT_PKT_STATUS socketopt by setting
BT_SK_PKT_STATUS. Then upon receiving an ISO packet the code would
attempt to store the Packet_Status_Flag to hci_skb_pkt_status which
is then forward to userspace in the form of BT_SCM_PKT_STATUS whenever
BT_PKT_STATUS has been enabled/set.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This makes the handling of BT_PKT_STATUS more generic so it can be
reused by sockets other than SCO like BT_DEFER_SETUP, etc.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
There may be a potential kernel crash risk if 'skb->len
- MTK_COREDUMP_END_LEN' value is less than 0 when doing
memcmp in btmtk_process_coredump().
Check the value is valid before doing memcmp.
[215.021695] Unable to handle kernel paging request at
virtual address ffffff939fffd3c5
[215.021781] Mem abort info:
[215.021805] ESR = 0x96000005
[215.021833] EC = 0x25: DABT (current EL), IL = 32 bits
[215.021861] SET = 0, FnV = 0
[215.021875] EA = 0, S1PTW = 0
[215.021886] Data abort info:
[215.021899] ISV = 0, ISS = 0x00000005
[215.021912] CM = 0, WnR = 0
[215.021929] swapper pgtable: 4k pages, 39-bit VAs,
pgdp=00000000410de000
[215.021943] [ffffff939fffd3c5] pgd=0000000000000000,
p4d=0000000000000000, pud=0000000000000000
[215.021979] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[215.022496] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.10.186#3
(HASH:ad23 4)
[215.022511] Hardware name: MediaTek Tomato board (DT)
[215.022530] pstate: 80400009 (Nzcv daif +PAN -UAO -TCO BTYPE=--)
[215.022556] pc : __pi_memcmp+0xd0/0x1b8
[215.022579] lr : btmtk_process_coredump+0xb0/0x5f8 [btmtk]
[215.022593] sp : ffffffc010003d40
[215.022607] x29: ffffffc010003d40 x28: 0000000000000006
[215.022633] x27: ffffffda696350c0 x26: 0000000000000002
[215.022659] x25: 00000000000003ff x24: ffffff9360cca804
[215.022685] x23: 0000000000000000 x22: ffffff9365638500
[215.022710] x21: ffffff9365638700 x20: 0000000000000000
[215.022736] x19: ffffff936002e000 x18: 0000000000000000
[215.022761] x17: 0000000000000180 x16: ffffffda6881b8b4
[215.022787] x15: 0000000000000001 x14: 0000000000002d00
[215.022812] x13: 0000000000060000 x12: 0000000000000181
[215.022837] x11: 0000000000000006 x10: fffffffffffffffd
[215.022862] x9 : 0000000000000006 x8 : 0000000000000003
[215.022887] x7 : 0000000000000000 x6 : 0000000000000000
[215.022913] x5 : ffffff93656387b8 x4 : 0000000000000000
[215.022938] x3 : ffffffc010003c18 x2 : 0000000000000006
[215.022963] x1 : ffffffda09d4124a x0 : ffffff939fffd3c5
[215.022989] Call trace:
[215.023012] __pi_memcmp+0xd0/0x1b8
[215.023053] btusb_recv_acl_mtk+0x64/0x90 [btusb (HASH:dc6b 5)]
[215.023087] btusb_recv_bulk+0x118/0x170 [btusb (HASH:dc6b 5)]
[215.023121] btusb_bulk_complete+0x8c/0x148 [btusb (HASH:dc6b 5)]
[215.023144] __usb_hcd_giveback_urb+0xbc/0x148
[215.023164] usb_giveback_urb_bh+0xb4/0x190
[215.023184] tasklet_action_common+0x98/0x1a0
[215.023201] tasklet_action+0x2c/0x38
[215.023220] __do_softirq+0xe0/0x38c
[215.023241] invoke_softirq+0x34/0x6c
[215.023258] irq_exit+0x6c/0xb0
[215.023279] __handle_domain_irq+0x98/0xd4
[215.023296] gic_handle_irq+0x5c/0x11c
[215.023313] el1_irq+0xd0/0x180
[215.023332] cpuidle_enter_state+0xac/0x338
[215.023349] cpuidle_enter+0x40/0x70
[215.023366] do_idle+0x150/0x278
[215.023384] cpu_startup_entry+0x2c/0x58
[215.023401] rest_init+0xdc/0xec
[215.023419] arch_call_rest_init+0x18/0x24
[215.023435] start_kernel+0x334/0x400
[215.023460] Code: 91002129 eb09010a 9a89810b cb0b0042 (38401403)
[215.023478] ---[ end trace 28668fd20c7a90cd ]
Fixes: 2822cd0173ad ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This one is found on the Dell Inspiron 2-in-1 7435
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e0f1 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Roger Gammans <rgammans@gammascience.co.uk>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If hci_unregister_dev() frees the hci_dev object but hci_suspend_notifier
may still be accessing it, it can cause the program to crash.
Here's the call trace:
<4>[102152.653246] Call Trace:
<4>[102152.653254] hci_suspend_sync+0x109/0x301 [bluetooth]
<4>[102152.653259] hci_suspend_dev+0x78/0xcd [bluetooth]
<4>[102152.653263] hci_suspend_notifier+0x42/0x7a [bluetooth]
<4>[102152.653268] notifier_call_chain+0x43/0x6b
<4>[102152.653271] __blocking_notifier_call_chain+0x48/0x69
<4>[102152.653273] __pm_notifier_call_chain+0x22/0x39
<4>[102152.653276] pm_suspend+0x287/0x57c
<4>[102152.653278] state_store+0xae/0xe5
<4>[102152.653281] kernfs_fop_write+0x109/0x173
<4>[102152.653284] __vfs_write+0x16f/0x1a2
<4>[102152.653287] ? selinux_file_permission+0xca/0x16f
<4>[102152.653289] ? security_file_permission+0x36/0x109
<4>[102152.653291] vfs_write+0x114/0x21d
<4>[102152.653293] __x64_sys_write+0x7b/0xdb
<4>[102152.653296] do_syscall_64+0x59/0x194
<4>[102152.653299] entry_SYSCALL_64_after_hwframe+0x5c/0xc1
This patch holds the reference count of the hci_dev object while
processing it in hci_suspend_notifier to avoid potential crash
caused by the race condition.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch adds code to check HCI_UART_PROTO_READY flag before
accessing hci_uart->proto. It fixes the race condition in
hci_uart_tty_ioctl() between HCIUARTSETPROTO and HCIUARTGETPROTO.
This issue bug found by Yu Hao and Weiteng Chen:
BUG: general protection fault in hci_uart_tty_ioctl [1]
The information of C reproducer can also reference the link [2]
Reported-by: Yu Hao <yhao016@ucr.edu>
Closes: https://lore.kernel.org/all/CA+UBctC3p49aTgzbVgkSZ2+TQcqq4fPDO7yZitFT5uBPDeCO2g@mail.gmail.com/ [1]
Reported-by: Weiteng Chen <wchen130@ucr.edu>
Closes: https://lore.kernel.org/lkml/CA+UBctDPEvHdkHMwD340=n02rh+jNRJNNQ5LBZNA+Wm4Keh2ow@mail.gmail.com/T/ [2]
Signed-off-by: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
strtobool() is the same as kstrtobool().
However, the latter is more used within the kernel.
In order to remove strtobool() and slightly simplify kstrtox.h, switch to
the other function name.
While at it, include the corresponding header file (<linux/kstrtox.h>)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 04ca & PID 3804 for MediaTek MT7922 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=3804 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 0489 & PID e102 for MediaTek MT7922 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e102 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
HCI_MAX_AD_LENGTH shall only be used if the controller doesn't support
extended advertising, otherwise HCI_MAX_EXT_AD_LENGTH shall be used
instead.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The hci_add_adv_monitor() hci_remove_adv_monitor() functions call
bt_dev_dbg() to print some debug statements. The bt_dev_dbg() macro
automatically adds in the device's name. That means that we shouldn't
include the name in the bt_dev_dbg() calls.
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Devices from /sys/kernel/debug/usb/devices:
T: Bus=09 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0036 Rev= 0.00
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID/PID 0489/e0f6 for MediaTek MT7922 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e0f6 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Return negative -EIO instead of positive EIO.
Fixes: 926df8962f3f ("Bluetooth: msft: Extended monitor tracking by address filter")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Some use cases require the user to be informed if BIG synchronization
fails. This commit makes it so that even if the BIG sync established
event arrives with error status, a new hconn is added for each BIS,
and the iso layer is notified about the failed connections.
Unsuccesful bis connections will be marked using the
HCI_CONN_BIG_SYNC_FAILED flag. From the iso layer, the POLLERR event
is triggered on the newly allocated bis sockets, before adding them
to the accept list of the parent socket.
From user space, a new fd for each failed bis connection will be
obtained by calling accept. The user should check for the POLLERR
event on the new socket, to determine if the connection was successful
or not.
The HCI_CONN_BIG_SYNC flag has been added to mark whether the BIG sync
has been successfully established. This flag is checked at bis cleanup,
so the HCI LE BIG Terminate Sync command is only issued if needed.
The BT_SK_BIG_SYNC flag indicates if BIG create sync has been called
for a listening socket, to avoid issuing the command everytime a BIGInfo
advertising report is received.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Asus ROG Ally gaming computer has a MediaTek MT7922 chip that uses USB id
0489:e0f5 and needs to be added to the table. Without this, the device is
not usable and gives the following error:
Bluetooth: hci0: Opcode 0x c03 failed: -110
Output from /sys/kernel/debug/usb/devices:
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e0f5 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Valentin David <valentin.david@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This attempts to always allocate a unique handle for connections so they
can be properly aborted by the likes of hci_abort_conn, so this uses the
invalid range as a pool of unset handles that way if userspace is trying
to create multiple connections at once each will be given a unique
handle which will be considered unset.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
ISO_LINK connections where not being handled properly on
hci_abort_conn_sync which sometimes resulted in sending the wrong
commands, or in case of having the reject command being sent by the
socket code (iso.c) which is sort of a layer violation.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This consolidates code for aborting connections using
hci_cmd_sync_queue so it is synchronized with other threads, but
because of the fact that some commands may block the cmd_sync_queue
while waiting specific events this attempt to cancel those requests by
using hci_cmd_sync_cancel.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch implement function .coredump() and dmp_hdr() in btusb
driver for MediaTek controller. FW core dump was triggered by FW
specific event to show something unexpected happened in the controller.
The driver would be responsible for collecting and uploading the device
core dump pieces in hci driver using core dump API. Once we finished
the whole process, the driver would reset the controller to recover the
kind of fatal error.
Co-developed-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Introduce btmtk_reset_work which can be called whenever the firmware abort,
HCI command timeout, other fatal error happen.
Co-developed-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use readx_poll_timeout instead of open coding to poll the hardware reset
status until it is done.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add printing firmware information part when driver loading firmware that
user can get mediatek bluetooth information.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add hardware variant(0x1c) for Gale Peak core (CNVi).
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In the case of a Synchronized Receiver capable device, enable at start-up the
events for PA reports, PA Sync Established and Big Info Adv reports.
Signed-off-by: Claudia Draghicescu <claudia.rosu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Since limited tracking device per condition, this feature is to support
tracking multiple devices concurrently.
When a pattern monitor detects the device, this feature issues an address
monitor for tracking that device. Let pattern monitor can keep monitor
new devices.
This feature adds an address filter when receiving a LE monitor device
event which monitor handle is for a pattern, and the controller started
monitoring the device. And this feature also has cancelled the monitor
advertisement from address filters when receiving a LE monitor device
event when the controller stopped monitoring the device specified by an
address and monitor handle.
Below is an example to know the feature adds the address filter.
//Add MSFT pattern monitor
< HCI Command: Vendor (0x3f|0x00f0) plen 14 #142 [hci0] 55.552420
03 b8 a4 03 ff 01 01 06 09 05 5f 52 45 46 .........._REF
> HCI Event: Command Complete (0x0e) plen 6 #143 [hci0] 55.653960
Vendor (0x3f|0x00f0) ncmd 2
Status: Success (0x00)
03 00
//Got event from the pattern monitor
> HCI Event: Vendor (0xff) plen 18 #148 [hci0] 58.384953
23 79 54 33 77 88 97 68 02 00 fb c1 29 eb 27 b8 #yT3w..h....).'.
00 01 ..
//Add MSFT address monitor (Sample address: B8:27:EB:29:C1:FB)
< HCI Command: Vendor (0x3f|0x00f0) plen 13 #149 [hci0] 58.385067
03 b8 a4 03 ff 04 00 fb c1 29 eb 27 b8 .........).'.
//Report to userspace about found device (ADV Monitor Device Found)
@ MGMT Event: Unknown (0x002f) plen 38 {0x0003} [hci0] 58.680042
01 00 fb c1 29 eb 27 b8 01 ce 00 00 00 00 16 00 ....).'.........
0a 09 4b 45 59 42 44 5f 52 45 46 02 01 06 03 19 ..KEYBD_REF.....
c1 03 03 03 12 18 ......
//Got event from address monitor
> HCI Event: Vendor (0xff) plen 18 #152 [hci0] 58.672956
23 79 54 33 77 88 97 68 02 00 fb c1 29 eb 27 b8 #yT3w..h....).'.
01 01
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch is added support Mediatek MT7925.
1. The firmware location of MT7925 will set to
/lib/firmware/mediatek/mt7925
2. Add Mediatek private data in hdev
to record the device for handle MT7925 flow.
3. Use the recoreded dev_id to condition chip reset flow.
The information in /sys/kernel/debug/usb/devices about the MT7925U
Bluetooth device is listed as the below
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 27 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0e8d ProdID=7925 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 5 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8f(I) Atr=03(Int.) MxPS= 2 Ivl=125us
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
I:* If#= 3 Alt= 0 #EPs= 9 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 2 Ivl=125us
Signed-off-by: Peter Tsao <peter.tsao@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
New Intel platforms supports reset of Bluetooth device via ACPI DSM
methods. The legacy reset mechanism via GPIO will be deprecated in
future. This patch checks the platform support for reset methods and if
supported uses the same instead of legacy GPIO toggling method.
ACPI firmware supports two types of reset method based on NIC card.
(Discrete or Integrated).
1. VSEC Type - Vendor Specific Extended Capability. Here BT_EN and
BT_IF_SELECT lines are driven by a register in PCH cluster. This
interface is supported on discrete BT solution.
2. WDISABLE2 - In this soluton, W_DISABLE2 pin in M.2 is connected to
physical GPIO from PCH. The DSM interface shall toggle this to recover
from error.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Intercept debug exception events from QCA controller and put them into
a devcoredump using hci devcoredump APIs of hci_core
Signed-off-by: Sai Teja Aluvala <quic_saluvala@quicinc.com>
V2 -> V3:
---------
changed hci_coredump_qca function
V1 -> V2:
---------
Updated to work with the updated HCI devcoredump API.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch implements the hci_qca driver side .coredump() callback to
trigger a devcoredump via sysfs.
Signed-off-by: Sai Teja Aluvala <quic_saluvala@quicinc.com>
v2 -> V3:
--------
Updated commit text
v1 -> V2:
--------
Updated to work with the updated HCI devcoredump API.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds support for creating multiple BIGs. According to
spec, each BIG shall have an unique handle, and each BIG should
be associated with a different advertising handle. Otherwise,
the LE Create BIG command will fail, with error code
Command Disallowed (for reusing a BIG handle), or
Unknown Advertising Identifier (for reusing an advertising
handle).
The btmon snippet below shows an exercise for creating two BIGs
for the same controller, by opening two isotest instances with
the following command:
tools/isotest -i hci0 -s 00:00:00:00:00:00
< HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31
Handle: 0x00
Advertising Handle: 0x01
Number of BIS: 1
SDU Interval: 10000 us (0x002710)
Maximum SDU size: 40
Maximum Latency: 10 ms (0x000a)
RTN: 0x02
PHY: LE 2M (0x02)
Packing: Sequential (0x00)
Framing: Unframed (0x00)
Encryption: 0x00
Broadcast Code: 00000000000000000000000000000000
> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 21
LE Broadcast Isochronous Group Complete (0x1b)
Status: Success (0x00)
Handle: 0x00
BIG Synchronization Delay: 912 us (0x000390)
Transport Latency: 912 us (0x000390)
PHY: LE 2M (0x02)
NSE: 3
BN: 1
PTO: 1
IRC: 3
Maximum PDU: 40
ISO Interval: 10.00 msec (0x0008)
Connection Handle #0: 10
< HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068)
Handle: 0x01
Advertising Handle: 0x02
Number of BIS: 1
SDU Interval: 10000 us (0x002710)
Maximum SDU size: 40
Maximum Latency: 10 ms (0x000a)
RTN: 0x02
PHY: LE 2M (0x02)
Packing: Sequential (0x00)
Framing: Unframed (0x00)
Encryption: 0x00
Broadcast Code: 00000000000000000000000000000000
> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This stores scm_creds into hci_skb_cb so they can be properly forwarded
to the likes of btmon which is then able to print information about the
process who is originating the traffic:
bluetoothd[35]: @ MGMT Command: Rea.. (0x0001) plen 0 {0x0001}
@ MGMT Event: Command Complete (0x0001) plen 6 {0x0001}
Read Management Version Information (0x0001) plen 3
bluetoothd[35]: < ACL Data T.. flags 0x00 dlen 41
ATT: Write Command (0x52) len 36
Handle: 0x0043 Type: ASE Control Point (0x2bc6)
Data: 020203000110270000022800020a00409c0001000110270000022800020a00409c00
Opcode: QoS Configuration (0x02)
Number of ASE(s): 2
ASE: #0
ASE ID: 0x03
CIG ID: 0x00
CIS ID: 0x01
SDU Interval: 10000 usec
Framing: Unframed (0x00)
PHY: 0x02
LE 2M PHY (0x02)
Max SDU: 40
RTN: 2
Max Transport Latency: 10
Presentation Delay: 40000 us
ASE: #1
ASE ID: 0x01
CIG ID: 0x00
CIS ID: 0x01
SDU Interval: 10000 usec
Framing: Unframed (0x00)
PHY: 0x02
LE 2M PHY (0x02)
Max SDU: 40
RTN: 2
Max Transport Latency: 10
Presentation Delay: 40000 us
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This makes sure peer information is always available via sock when using
bt_sock_alloc.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This consolidates code around sk_alloc into bt_sock_alloc which does
take care of common initialization.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The original code did not determine the length value of the HCI command
for drop fw even there's no parameter needed. In this commit, use struct
hci_command_hdr to manage opcode and length. It would be more regular and
more readable.
Suggested-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
LE Create CIS command shall not be sent before all CIS Established
events from its previous invocation have been processed. Currently it is
sent via hci_sync but that only waits for the first event, but there can
be multiple.
Make it wait for all events, and simplify the CIS creation as follows:
Add new flag HCI_CONN_CREATE_CIS, which is set if Create CIS has been
sent for the connection but it is not yet completed.
Make BT_CONNECT state to mean the connection wants Create CIS.
On events after which new Create CIS may need to be sent, send it if
possible and some connections need it. These events are:
hci_connect_cis, iso_connect_cfm, hci_cs_le_create_cis,
hci_le_cis_estabilished_evt.
The Create CIS status/completion events shall queue new Create CIS only
if at least one of the connections transitions away from BT_CONNECT, so
that we don't loop if controller is sending bogus events.
This fixes sending multiple CIS Create for the same CIS in the
"ISO AC 6(i) - Success" BlueZ test case:
< HCI Command: LE Create Co.. (0x08|0x0064) plen 9 #129 [hci0]
Number of CIS: 2
CIS Handle: 257
ACL Handle: 42
CIS Handle: 258
ACL Handle: 42
> HCI Event: Command Status (0x0f) plen 4 #130 [hci0]
LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 29 #131 [hci0]
LE Connected Isochronous Stream Established (0x19)
Status: Success (0x00)
Connection Handle: 257
...
< HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 #132 [hci0]
...
> HCI Event: Command Complete (0x0e) plen 6 #133 [hci0]
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
...
< HCI Command: LE Create Co.. (0x08|0x0064) plen 5 #134 [hci0]
Number of CIS: 1
CIS Handle: 258
ACL Handle: 42
> HCI Event: Command Status (0x0f) plen 4 #135 [hci0]
LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1
Status: ACL Connection Already Exists (0x0b)
> HCI Event: LE Meta Event (0x3e) plen 29 #136 [hci0]
LE Connected Isochronous Stream Established (0x19)
Status: Success (0x00)
Connection Handle: 258
...
Fixes: c09b80be6ffc ("Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
It is required for some configurations to have multiple BISes as part
of the same BIG.
Similar to the flow implemented for unicast, DEFER_SETUP will also be
used to bind multiple BISes for the same BIG, before starting Periodic
Advertising and creating the BIG.
The user will have to open a new socket for each BIS. By setting the
BT_DEFER_SETUP socket option and calling connect, a new connection
will be added for the BIG and advertising handle set by the socket
QoS parameters. Since all BISes will be bound for the same BIG and
advertising handle, the socket QoS options and base parameters should
match for all connections.
By calling connect on a socket that does not have the BT_DEFER_SETUP
option set, periodic advertising will be started and the BIG will
be created, with a BIS for each previously bound connection. Since
a BIG cannot be reconfigured with additional BISes after creation,
no more connections can be bound for the BIG after the start periodic
advertising and create BIG commands have been queued.
The bis_cleanup function has also been updated, so that the advertising
set and the BIG will not be terminated unless there are no more
bound or connected BISes.
The HCI_CONN_BIG_CREATED connection flag has been added to indicate
that the BIG has been successfully created. This flag is checked at
bis_cleanup, so that the BIG is only terminated if the
HCI_LE_Create_BIG_Complete has been received.
This implementation has been tested on hardware, using the "isotest"
tool with an additional command line option, to specify the number of
BISes to create as part of the desired BIG:
tools/isotest -i hci0 -s 00:00:00:00:00:00 -N 2 -G 1 -T 1
The btmon log shows that a BIG containing 2 BISes has been created:
< HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31
Handle: 0x01
Advertising Handle: 0x01
Number of BIS: 2
SDU Interval: 10000 us (0x002710)
Maximum SDU size: 40
Maximum Latency: 10 ms (0x000a)
RTN: 0x02
PHY: LE 2M (0x02)
Packing: Sequential (0x00)
Framing: Unframed (0x00)
Encryption: 0x00
Broadcast Code: 00000000000000000000000000000000
> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 23
LE Broadcast Isochronous Group Complete (0x1b)
Status: Success (0x00)
Handle: 0x01
BIG Synchronization Delay: 1974 us (0x0007b6)
Transport Latency: 1974 us (0x0007b6)
PHY: LE 2M (0x02)
NSE: 3
BN: 1
PTO: 1
IRC: 3
Maximum PDU: 40
ISO Interval: 10.00 msec (0x0008)
Connection Handle #0: 10
Connection Handle #1: 11
< HCI Command: LE Setup Isochronous Data Path (0x08|0x006e) plen 13
Handle: 10
Data Path Direction: Input (Host to Controller) (0x00)
Data Path: HCI (0x00)
Coding Format: Transparent (0x03)
Company Codec ID: Ericsson Technology Licensing (0)
Vendor Codec ID: 0
Controller Delay: 0 us (0x000000)
Codec Configuration Length: 0
Codec Configuration:
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 10
< HCI Command: LE Setup Isochronous Data Path (0x08|0x006e) plen 13
Handle: 11
Data Path Direction: Input (Host to Controller) (0x00)
Data Path: HCI (0x00)
Coding Format: Transparent (0x03)
Company Codec ID: Ericsson Technology Licensing (0)
Vendor Codec ID: 0
Controller Delay: 0 us (0x000000)
Codec Configuration Length: 0
Codec Configuration:
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 11
< ISO Data TX: Handle 10 flags 0x02 dlen 44
< ISO Data TX: Handle 11 flags 0x02 dlen 44
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 10
Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 11
Count: 1
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Catch debug exception from controller and driver, and trigger a
devcoredump using hci devcoredump APIs. The debug exception data
will be parsed in userspace.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
