Age | Commit message (Collapse) | Author | Files | Lines |
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"The most important change is that we reduce L1_CACHE_BYTES to 16
bytes, for which a trivial patch for XPS in the network layer was
needed. Then we wire up the sys_membarrier and userfaultfd syscalls
and added two other small cleanups"
* 'parisc-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Change L1_CACHE_BYTES to 16
net/xps: Fix calculation of initial number of xps queues
parisc: reduce syslog debug output
parisc: serial/mux: Convert to uart_console_device instead of open-coded
parisc: Wire up userfaultfd syscall
parisc: allocate sys_membarrier system call number
|
|
Pull IDE fixlet from David Miller:
"Just a y2038 fix to the pdc202xx_new IDE driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: pdc202xx_new: Replace timeval with ktime_t
|
|
Pull networking updates from David Miller:
Changes of note:
1) Allow to schedule ICMP packets in IPVS, from Alex Gartrell.
2) Provide FIB table ID in ipv4 route dumps just as ipv6 does, from
David Ahern.
3) Allow the user to ask for the statistics to be filtered out of
ipv4/ipv6 address netlink dumps. From Sowmini Varadhan.
4) More work to pass the network namespace context around deep into
various packet path APIs, starting with the netfilter hooks. From
Eric W Biederman.
5) Add layer 2 TX/RX checksum offloading to qeth driver, from Thomas
Richter.
6) Use usec resolution for SYN/ACK RTTs in TCP, from Yuchung Cheng.
7) Support Very High Throughput in wireless MESH code, from Bob
Copeland.
8) Allow setting the ageing_time in switchdev/rocker. From Scott
Feldman.
9) Properly autoload L2TP type modules, from Stephen Hemminger.
10) Fix and enable offload features by default in 8139cp driver, from
David Woodhouse.
11) Support both ipv4 and ipv6 sockets in a single vxlan device, from
Jiri Benc.
12) Fix CWND limiting of thin streams in TCP, from Bendik Rønning
Opstad.
13) Fix IPSEC flowcache overflows on large systems, from Steffen
Klassert.
14) Convert bridging to track VLANs using rhashtable entries rather than
a bitmap. From Nikolay Aleksandrov.
15) Make TCP listener handling completely lockless, this is a major
accomplishment. Incoming request sockets now live in the
established hash table just like any other socket too.
From Eric Dumazet.
15) Provide more bridging attributes to netlink, from Nikolay
Aleksandrov.
16) Use hash based algorithm for ipv4 multipath routing, this was very
long overdue. From Peter Nørlund.
17) Several y2038 cures, mostly avoiding timespec. From Arnd Bergmann.
18) Allow non-root execution of EBPF programs, from Alexei Starovoitov.
19) Support SO_INCOMING_CPU as setsockopt, from Eric Dumazet. This
influences the port binding selection logic used by SO_REUSEPORT.
20) Add ipv6 support to VRF, from David Ahern.
21) Add support for Mellanox Spectrum switch ASIC, from Jiri Pirko.
22) Add rtl8xxxu Realtek wireless driver, from Jes Sorensen.
23) Implement RACK loss recovery in TCP, from Yuchung Cheng.
24) Support multipath routes in MPLS, from Roopa Prabhu.
25) Fix POLLOUT notification for listening sockets in AF_UNIX, from Eric
Dumazet.
26) Add new QED Qlogic river, from Yuval Mintz, Manish Chopra, and
Sudarsana Kalluru.
27) Don't fetch timestamps on AF_UNIX sockets, from Hannes Frederic
Sowa.
28) Support ipv6 geneve tunnels, from John W Linville.
29) Add flood control support to switchdev layer, from Ido Schimmel.
30) Fix CHECKSUM_PARTIAL handling of potentially fragmented frames, from
Hannes Frederic Sowa.
31) Support persistent maps and progs in bpf, from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1790 commits)
sh_eth: use DMA barriers
switchdev: respect SKIP_EOPNOTSUPP flag in case there is no recursion
net: sched: kill dead code in sch_choke.c
irda: Delete an unnecessary check before the function call "irlmp_unregister_service"
net: dsa: mv88e6xxx: include DSA ports in VLANs
net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports
net/core: fix for_each_netdev_feature
vlan: Invoke driver vlan hooks only if device is present
arcnet/com20020: add LEDS_CLASS dependency
bpf, verifier: annotate verbose printer with __printf
dp83640: Only wait for timestamps for packets with timestamping enabled.
ptp: Change ptp_class to a proper bitmask
dp83640: Prune rx timestamp list before reading from it
dp83640: Delay scheduled work.
dp83640: Include hash in timestamp/packet matching
ipv6: fix tunnel error handling
net/mlx5e: Fix LSO vlan insertion
net/mlx5e: Re-eanble client vlan TX acceleration
net/mlx5e: Return error in case mlx5e_set_features() fails
net/mlx5e: Don't allow more than max supported channels
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Add support for cipher output IVs in testmgr
- Add missing crypto_ahash_blocksize helper
- Mark authenc and des ciphers as not allowed under FIPS.
Algorithms:
- Add CRC support to 842 compression
- Add keywrap algorithm
- A number of changes to the akcipher interface:
+ Separate functions for setting public/private keys.
+ Use SG lists.
Drivers:
- Add Intel SHA Extension optimised SHA1 and SHA256
- Use dma_map_sg instead of custom functions in crypto drivers
- Add support for STM32 RNG
- Add support for ST RNG
- Add Device Tree support to exynos RNG driver
- Add support for mxs-dcp crypto device on MX6SL
- Add xts(aes) support to caam
- Add ctr(aes) and xts(aes) support to qat
- A large set of fixes from Russell King for the marvell/cesa driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (115 commits)
crypto: asymmetric_keys - Fix unaligned access in x509_get_sig_params()
crypto: akcipher - Don't #include crypto/public_key.h as the contents aren't used
hwrng: exynos - Add Device Tree support
hwrng: exynos - Fix missing configuration after suspend to RAM
hwrng: exynos - Add timeout for waiting on init done
dt-bindings: rng: Describe Exynos4 PRNG bindings
crypto: marvell/cesa - use __le32 for hardware descriptors
crypto: marvell/cesa - fix missing cpu_to_le32() in mv_cesa_dma_add_op()
crypto: marvell/cesa - use memcpy_fromio()/memcpy_toio()
crypto: marvell/cesa - use gfp_t for gfp flags
crypto: marvell/cesa - use dma_addr_t for cur_dma
crypto: marvell/cesa - use readl_relaxed()/writel_relaxed()
crypto: caam - fix indentation of close braces
crypto: caam - only export the state we really need to export
crypto: caam - fix non-block aligned hash calculation
crypto: caam - avoid needlessly saving and restoring caam_hash_ctx
crypto: caam - print errno code when hash registration fails
crypto: marvell/cesa - fix memory leak
crypto: marvell/cesa - fix first-fragment handling in mv_cesa_ahash_dma_last_req()
crypto: marvell/cesa - rearrange handling for sw padded hashes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 platform changes from Ingo Molnar:
"Misc updates to the Intel MID and SGI UV platforms"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel-mid: Make intel_mid_ops static
arch/x86/intel-mid: Use kmemdup rather than duplicating its implementation
x86/platform/uv: Implement simple dump failover if kdump fails
x86/platform/uv: Insert per_cpu accessor function on uv_hub_nmi
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm changes from Ingo Molnar:
"The main changes are: continued PAT work by Toshi Kani, plus a new
boot time warning about insecure RWX kernel mappings, by Stephen
Smalley.
The new CONFIG_DEBUG_WX=y warning is marked default-y if
CONFIG_DEBUG_RODATA=y is already eanbled, as a special exception, as
these bugs are hard to notice and this check already found several
live bugs"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Warn on W^X mappings
x86/mm: Fix no-change case in try_preserve_large_page()
x86/mm: Fix __split_large_page() to handle large PAT bit
x86/mm: Fix try_preserve_large_page() to handle large PAT bit
x86/mm: Fix gup_huge_p?d() to handle large PAT bit
x86/mm: Fix slow_virt_to_phys() to handle large PAT bit
x86/mm: Fix page table dump to show PAT bit
x86/asm: Add pud_pgprot() and pmd_pgprot()
x86/asm: Fix pud/pmd interfaces to handle large PAT bit
x86/asm: Add pud/pmd mask interfaces to handle large PAT bit
x86/asm: Move PUD_PAGE macros to page_types.h
x86/vdso32: Define PGTABLE_LEVELS to 32bit VDSO
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 sigcontext header cleanups from Ingo Molnar:
"This series reorganizes and cleans up various aspects of the main
sigcontext UAPI headers, such as unifying the data structures and
updating/adding lots of comments to explain all the ABI details and
quirks. The headers can now also be built in user-space standalone"
* 'x86-headers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/headers: Clean up too long lines
x86/headers: Remove <asm/sigcontext.h> references on the kernel side
x86/headers: Remove direct sigcontext32.h uses
x86/headers: Convert sigcontext_ia32 uses to sigcontext_32
x86/headers: Unify 'struct sigcontext_ia32' and 'struct sigcontext_32'
x86/headers: Make sigcontext pointers bit independent
x86/headers: Move the 'struct sigcontext' definitions into the UAPI header
x86/headers: Clean up the kernel's struct sigcontext types to be ABI-clean
x86/headers: Convert uses of _fpstate_ia32 to _fpstate_32
x86/headers: Unify 'struct _fpstate_ia32' and i386 struct _fpstate
x86/headers: Unify register type definitions between 32-bit compat and i386
x86/headers: Use ABI types consistently in sigcontext*.h
x86/headers: Separate out legacy user-space structure definitions
x86/headers: Clean up and better document uapi/asm/sigcontext.h
x86/headers: Clean up uapi/asm/sigcontext32.h
x86/headers: Fix (old) header file dependency bug in uapi/asm/sigcontext32.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fpu changes from Ingo Molnar:
"There are two main areas of changes:
- Rework of the extended FPU state code to robustify the kernel's
usage of cpuid provided xstate sizes - and related changes (Dave
Hansen)"
- math emulation enhancements: new modern FPU instructions support,
with testcases, plus cleanups (Denys Vlasnko)"
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/fpu: Fixup uninitialized feature_name warning
x86/fpu/math-emu: Add support for FISTTP instructions
x86/fpu/math-emu, selftests: Add test for FISTTP instructions
x86/fpu/math-emu: Add support for FCMOVcc insns
x86/fpu/math-emu: Add support for F[U]COMI[P] insns
x86/fpu/math-emu: Remove define layer for undocumented opcodes
x86/fpu/math-emu, selftests: Add tests for FCMOV and FCOMI insns
x86/fpu/math-emu: Remove !NO_UNDOC_CODE
x86/fpu: Check CPU-provided sizes against struct declarations
x86/fpu: Check to ensure increasing-offset xstate offsets
x86/fpu: Correct and check XSAVE xstate size calculations
x86/fpu: Add C structures for AVX-512 state components
x86/fpu: Rework YMM definition
x86/fpu/mpx: Rework MPX 'xstate' types
x86/fpu: Add xfeature_enabled() helper instead of test_bit()
x86/fpu: Remove 'xfeature_nr'
x86/fpu: Rework XSTATE_* macros to remove magic '2'
x86/fpu: Rename XFEATURES_NR_MAX
x86/fpu: Rename XSAVE macros
x86/fpu: Remove partial LWP support definitions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 kgdb fixlet from Ingo Molnar:
"A single debugging related commit: compress the memory usage of a kgdb
data structure"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kgdb: Replace bool_int_array[NR_CPUS] with bitmap
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cpu changes from Ingo Molnar:
"Two changes in this cycle: a Kconfig help text enhancement, and an AMD
CLZERO instruction capability detection and enumeration"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add CLZERO detection
x86/Kconfig/cpus: Fix/complete CPU type help texts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cleanups from Ingo Molnar:
"An early_printk cleanup plus deinlining enhancements"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/early_printk: Set __iomem address space for IO
x86/signal: Deinline get_sigframe, save 240 bytes
x86: Deinline early_console_register, save 403 bytes
x86/e820: Deinline e820_type_to_string, save 126 bytes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 boot cleanup from Ingo Molnar:
"A single commit: remove an obsolete kcrash boot flag"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kexec: Remove obsolete 'in_crash_kexec' flag
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 asm changes from Ingo Molnar:
"The main change in this cycle is another step in the big x86 system
call interface rework by Andy Lutomirski, which moves most of the low
level x86 entry code from assembly to C, for all syscall entries
except native 64-bit system calls:
arch/x86/entry/entry_32.S | 182 ++++------
arch/x86/entry/entry_64_compat.S | 547 ++++++++-----------------------
194 insertions(+), 535 deletions(-)
... our hope is that the final remaining step (converting native
64-bit system calls) will be less painful as all the previous steps,
given that most of the legacies and quirks are concentrated around
native 32-bit and compat environments"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (47 commits)
x86/entry/32: Fix FS and GS restore in opportunistic SYSEXIT
x86/entry/32: Fix entry_INT80_32() to expect interrupts to be on
um/x86: Fix build after x86 syscall changes
x86/asm: Remove the xyz_cfi macros from dwarf2.h
selftests/x86: Style fixes for the 'unwind_vdso' test
x86/entry/64/compat: Document sysenter_fix_flags's reason for existence
x86/entry: Split and inline syscall_return_slowpath()
x86/entry: Split and inline prepare_exit_to_usermode()
x86/entry: Use pt_regs_to_thread_info() in syscall entry tracing
x86/entry: Hide two syscall entry assertions behind CONFIG_DEBUG_ENTRY
x86/entry: Micro-optimize compat fast syscall arg fetch
x86/entry: Force inlining of 32-bit syscall code
x86/entry: Make irqs_disabled checks in exit code depend on lockdep
x86/entry: Remove unnecessary IRQ twiddling in fast 32-bit syscalls
x86/asm: Remove thread_info.sysenter_return
x86/entry/32: Re-implement SYSENTER using the new C path
x86/entry/32: Switch INT80 to the new C syscall path
x86/entry/32: Open-code return tracking from fork and kthreads
x86/entry/compat: Implement opportunistic SYSRETL for compat syscalls
x86/vdso/compat: Wire up SYSENTER and SYSCSALL for compat userspace
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 apic changes from Ingo Molnar:
"The main changes in this cycle were:
- Numachip updates: new hardware support, fixes and cleanups.
(Daniel J Blueman)
- misc smaller cleanups and fixlets"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/io_apic: Make eoi_ioapic_pin() static
x86/irq: Drop unlikely before IS_ERR_OR_NULL
x86/x2apic: Make stub functions available even if !CONFIG_X86_LOCAL_APIC
x86/apic: Deinline various functions
x86/numachip: Fix timer build conflict
x86/numachip: Introduce Numachip2 timer mechanisms
x86/numachip: Add Numachip IPI optimisations
x86/numachip: Add Numachip2 APIC support
x86/numachip: Cleanup Numachip support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler changes from Ingo Molnar:
"The main changes in this cycle were:
- sched/fair load tracking fixes and cleanups (Byungchul Park)
- Make load tracking frequency scale invariant (Dietmar Eggemann)
- sched/deadline updates (Juri Lelli)
- stop machine fixes, cleanups and enhancements for bugs triggered by
CPU hotplug stress testing (Oleg Nesterov)
- scheduler preemption code rework: remove PREEMPT_ACTIVE and related
cleanups (Peter Zijlstra)
- Rework the sched_info::run_delay code to fix races (Peter Zijlstra)
- Optimize per entity utilization tracking (Peter Zijlstra)
- ... misc other fixes, cleanups and smaller updates"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
sched: Don't scan all-offline ->cpus_allowed twice if !CONFIG_CPUSETS
sched: Move cpu_active() tests from stop_two_cpus() into migrate_swap_stop()
sched: Start stopper early
stop_machine: Kill cpu_stop_threads->setup() and cpu_stop_unpark()
stop_machine: Kill smp_hotplug_thread->pre_unpark, introduce stop_machine_unpark()
stop_machine: Change cpu_stop_queue_two_works() to rely on stopper->enabled
stop_machine: Introduce __cpu_stop_queue_work() and cpu_stop_queue_two_works()
stop_machine: Ensure that a queued callback will be called before cpu_stop_park()
sched/x86: Fix typo in __switch_to() comments
sched/core: Remove a parameter in the migrate_task_rq() function
sched/core: Drop unlikely behind BUG_ON()
sched/core: Fix task and run queue sched_info::run_delay inconsistencies
sched/numa: Fix task_tick_fair() from disabling numa_balancing
sched/core: Add preempt_count invariant check
sched/core: More notrace annotations
sched/core: Kill PREEMPT_ACTIVE
sched/core, sched/x86: Kill thread_info::saved_preempt_count
sched/core: Simplify preempt_count tests
sched/core: Robustify preemption leak checks
sched/core: Stop setting PREEMPT_ACTIVE
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RAS changes from Ingo Molnar:
"The main system reliability related changes were from x86, but also
some generic RAS changes:
- AMD MCE error injection subsystem enhancements. (Aravind
Gopalakrishnan)
- Fix MCE and CPU hotplug interaction bug. (Ashok Raj)
- kcrash bootup robustness fix. (Baoquan He)
- kcrash cleanups. (Borislav Petkov)
- x86 microcode driver rework: simplify it by unmodularizing it and
other cleanups. (Borislav Petkov)"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/mce: Add a default case to the switch in __mcheck_cpu_ancient_init()
x86/mce: Add a Scalable MCA vendor flags bit
MAINTAINERS: Unify the microcode driver section
x86/microcode/intel: Move #ifdef DEBUG inside the function
x86/microcode/amd: Remove maintainers from comments
x86/microcode: Remove modularization leftovers
x86/microcode: Merge the early microcode loader
x86/microcode: Unmodularize the microcode driver
x86/mce: Fix thermal throttling reporting after kexec
kexec/crash: Say which char is the unrecognized
x86/setup/crash: Check memblock_reserve() retval
x86/setup/crash: Cleanup some more
x86/setup/crash: Remove alignment variable
x86/setup: Cleanup crashkernel reservation functions
x86/amd_nb, EDAC: Rename amd_get_node_id()
x86/setup: Do not reserve crashkernel high memory if low reservation failed
x86/microcode/amd: Do not overwrite final patch levels
x86/microcode/amd: Extract current patch level read to a function
x86/ras/mce_amd_inj: Inject bank 4 errors on the NBC
x86/ras/mce_amd_inj: Trigger deferred and thresholding errors interrupts
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Improve accuracy of perf/sched clock on x86. (Adrian Hunter)
- Intel DS and BTS updates. (Alexander Shishkin)
- Intel cstate PMU support. (Kan Liang)
- Add group read support to perf_event_read(). (Peter Zijlstra)
- Branch call hardware sampling support, implemented on x86 and
PowerPC. (Stephane Eranian)
- Event groups transactional interface enhancements. (Sukadev
Bhattiprolu)
- Enable proper x86/intel/uncore PMU support on multi-segment PCI
systems. (Taku Izumi)
- ... misc fixes and cleanups.
The perf tooling team was very busy again with 200+ commits, the full
diff doesn't fit into lkml size limits. Here's an (incomplete) list
of the tooling highlights:
New features:
- Change the default event used in all tools (record/top): use the
most precise "cycles" hw counter available, i.e. when the user
doesn't specify any event, it will try using cycles:ppp, cycles:pp,
etc and fall back transparently until it finds a working counter.
(Arnaldo Carvalho de Melo)
- Integration of perf with eBPF that, given an eBPF .c source file
(or .o file built for the 'bpf' target with clang), will get it
automatically built, validated and loaded into the kernel via the
sys_bpf syscall, which can then be used and seen using 'perf trace'
and other tools.
(Wang Nan)
Various user interface improvements:
- Automatic pager invocation on long help output. (Namhyung Kim)
- Search for more options when passing args to -h, e.g.: (Arnaldo
Carvalho de Melo)
$ perf report -h interface
Usage: perf report [<options>]
--gtk Use the GTK2 interface
--stdio Use the stdio interface
--tui Use the TUI interface
- Show ordered command line options when -h is used or when an
unknown option is specified. (Arnaldo Carvalho de Melo)
- If options are passed after -h, show just its descriptions, not all
options. (Arnaldo Carvalho de Melo)
- Implement column based horizontal scrolling in the hists browser
(top, report), making it possible to use the TUI for things like
'perf mem report' where there are many more columns than can fit in
a terminal. (Arnaldo Carvalho de Melo)
- Enhance the error reporting of tracepoint event parsing, e.g.:
$ oldperf record -e sched:sched_switc usleep 1
event syntax error: 'sched:sched_switc'
\___ unknown tracepoint
Run 'perf list' for a list of valid events
Now we get the much nicer:
$ perf record -e sched:sched_switc ls
event syntax error: 'sched:sched_switc'
\___ can't access trace events
Error: No permissions to read /sys/kernel/debug/tracing/events/sched/sched_switc
Hint: Try 'sudo mount -o remount,mode=755 /sys/kernel/debug'
And after we have those mount point permissions fixed:
$ perf record -e sched:sched_switc ls
event syntax error: 'sched:sched_switc'
\___ unknown tracepoint
Error: File /sys/kernel/debug/tracing/events/sched/sched_switc not found.
Hint: Perhaps this kernel misses some CONFIG_ setting to enable this feature?.
I.e. basically now the event parsing routing uses the strerror_open()
routines introduced by and used in 'perf trace' work. (Jiri Olsa)
- Fail properly when pattern matching fails to find a tracepoint,
i.e. '-e non:existent' was being correctly handled, with a proper
error message about that not being a valid event, but '-e
non:existent*' wasn't, fix it. (Jiri Olsa)
- Do event name substring search as last resort in 'perf list'.
(Arnaldo Carvalho de Melo)
E.g.:
# perf list clock
List of pre-defined events (to be used in -e):
cpu-clock [Software event]
task-clock [Software event]
uncore_cbox_0/clockticks/ [Kernel PMU event]
uncore_cbox_1/clockticks/ [Kernel PMU event]
kvm:kvm_pvclock_update [Tracepoint event]
kvm:kvm_update_master_clock [Tracepoint event]
power:clock_disable [Tracepoint event]
power:clock_enable [Tracepoint event]
power:clock_set_rate [Tracepoint event]
syscalls:sys_enter_clock_adjtime [Tracepoint event]
syscalls:sys_enter_clock_getres [Tracepoint event]
syscalls:sys_enter_clock_gettime [Tracepoint event]
syscalls:sys_enter_clock_nanosleep [Tracepoint event]
syscalls:sys_enter_clock_settime [Tracepoint event]
syscalls:sys_exit_clock_adjtime [Tracepoint event]
syscalls:sys_exit_clock_getres [Tracepoint event]
syscalls:sys_exit_clock_gettime [Tracepoint event]
syscalls:sys_exit_clock_nanosleep [Tracepoint event]
syscalls:sys_exit_clock_settime [Tracepoint event]
Intel PT hardware tracing enhancements:
- Accept a zero --itrace period, meaning "as often as possible". In
the case of Intel PT that is the same as a period of 1 and a unit
of 'instructions' (i.e. --itrace=i1i). (Adrian Hunter)
- Harmonize itrace's synthesized callchains with the existing
--max-stack tool option. (Adrian Hunter)
- Allow time to be displayed in nanoseconds in 'perf script'.
(Adrian Hunter)
- Fix potential infinite loop when handling Intel PT timestamps.
(Adrian Hunter)
- Slighly improve Intel PT debug logging. (Adrian Hunter)
- Warn when AUX data has been lost, just like when processing
PERF_RECORD_LOST. (Adrian Hunter)
- Further document export-to-postgresql.py script. (Adrian Hunter)
- Add option to synthesize branch stack from auxtrace data. (Adrian
Hunter)
Misc notable changes:
- Switch the default callchain output mode to 'graph,0.5,caller', to
make it look like the default for other tools, reducing the
learning curve for people used to 'caller' based viewing. (Arnaldo
Carvalho de Melo)
- various call chain usability enhancements. (Namhyung Kim)
- Introduce the 'P' event modifier, meaning 'max precision level,
please', i.e.:
$ perf record -e cycles:P usleep 1
Is now similar to:
$ perf record usleep 1
Useful, for instance, when specifying multiple events. (Jiri Olsa)
- Add 'socket' sort entry, to sort by the processor socket in 'perf
top' and 'perf report'. (Kan Liang)
- Introduce --socket-filter to 'perf report', for filtering by
processor socket. (Kan Liang)
- Add new "Zoom into Processor Socket" operation in the perf hists
browser, used in 'perf top' and 'perf report'. (Kan Liang)
- Allow probing on kmodules without DWARF. (Masami Hiramatsu)
- Fix 'perf probe -l' for probes added to kernel module functions.
(Masami Hiramatsu)
- Preparatory work for the 'perf stat record' feature that will allow
generating perf.data files with counting data in addition to the
sampling mode we have now (Jiri Olsa)
- Update libtraceevent KVM plugin. (Paolo Bonzini)
- ... plus lots of other enhancements that I failed to list properly,
by: Adrian Hunter, Alexander Shishkin, Andi Kleen, Andrzej Hajda,
Arnaldo Carvalho de Melo, Dima Kogan, Don Zickus, Geliang Tang, He
Kuang, Huaitong Han, Ingo Molnar, Jan Stancek, Jiri Olsa, Kan
Liang, Kirill Tkhai, Masami Hiramatsu, Matt Fleming, Namhyung Kim,
Paolo Bonzini, Peter Zijlstra, Rabin Vincent, Scott Wood, Stephane
Eranian, Sukadev Bhattiprolu, Taku Izumi, Vaishali Thakkar, Wang
Nan, Yang Shi and Yunlong Song"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (260 commits)
perf unwind: Pass symbol source to libunwind
tools build: Fix libiberty feature detection
perf tools: Compile scriptlets to BPF objects when passing '.c' to --event
perf record: Add clang options for compiling BPF scripts
perf bpf: Attach eBPF filter to perf event
perf tools: Make sure fixdep is built before libbpf
perf script: Enable printing of branch stack
perf trace: Add cmd string table to decode sys_bpf first arg
perf bpf: Collect perf_evsel in BPF object files
perf tools: Load eBPF object into kernel
perf tools: Create probe points for BPF programs
perf tools: Enable passing bpf object file to --event
perf ebpf: Add the libbpf glue
perf tools: Make perf depend on libbpf
perf symbols: Fix endless loop in dso__split_kallsyms_for_kcore
perf tools: Enable pre-event inherit setting by config terms
perf symbols: we can now read separate debug-info files based on a build ID
perf symbols: Fix type error when reading a build-id
perf tools: Search for more options when passing args to -h
perf stat: Cache aggregated map entries in extra cpumap
...
|
|
This seems to be a mis-reading of how alpha memory ordering works, and
is not backed up by the alpha architecture manual. The helper functions
don't do anything special on any other architectures, and the arguments
that support them being safe on other architectures also argue that they
are safe on alpha.
Basically, the "control dependency" is between a previous read and a
subsequent write that is dependent on the value read. Even if the
subsequent write is actually done speculatively, there is no way that
such a speculative write could be made visible to other cpu's until it
has been committed, which requires validating the speculation.
Note that most weakely ordered architectures (very much including alpha)
do not guarantee any ordering relationship between two loads that depend
on each other on a control dependency:
read A
if (val == 1)
read B
because the conditional may be predicted, and the "read B" may be
speculatively moved up to before reading the value A. So we require the
user to insert a smp_rmb() between the two accesses to be correct:
read A;
if (A == 1)
smp_rmb()
read B
Alpha is further special in that it can break that ordering even if the
*address* of B depends on the read of A, because the cacheline that is
read later may be stale unless you have a memory barrier in between the
pointer read and the read of the value behind a pointer:
read ptr
read offset(ptr)
whereas all other weakly ordered architectures guarantee that the data
dependency (as opposed to just a control dependency) will order the two
accesses. As a result, alpha needs a "smp_read_barrier_depends()" in
between those two reads for them to be ordered.
The coontrol dependency that "READ_ONCE_CTRL()" and "atomic_read_ctrl()"
had was a control dependency to a subsequent *write*, however, and
nobody can finalize such a subsequent write without having actually done
the read. And were you to write such a value to a "stale" cacheline
(the way the unordered reads came to be), that would seem to lose the
write entirely.
So the things that make alpha able to re-order reads even more
aggressively than other weak architectures do not seem to be relevant
for a subsequent write. Alpha memory ordering may be strange, but
there's no real indication that it is *that* strange.
Also, the alpha architecture reference manual very explicitly talks
about the definition of "Dependence Constraints" in section 5.6.1.7,
where a preceding read dominates a subsequent write.
Such a dependence constraint admittedly does not impose a BEFORE (alpha
architecture term for globally visible ordering), but it does guarantee
that there can be no "causal loop". I don't see how you could avoid
such a loop if another cpu could see the stored value and then impact
the value of the first read. Put another way: the read and the write
could not be seen as being out of order wrt other cpus.
So I do not see how these "x_ctrl()" functions can currently be necessary.
I may have to eat my words at some point, but in the absense of clear
proof that alpha actually needs this, or indeed even an explanation of
how alpha could _possibly_ need it, I do not believe these functions are
called for.
And if it turns out that alpha really _does_ need a barrier for this
case, that barrier still should not be "smp_read_barrier_depends()".
We'd have to make up some new speciality barrier just for alpha, along
with the documentation for why it really is necessary.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul E McKenney <paulmck@us.ibm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking changes from Ingo Molnar:
"The main changes in this cycle were:
- More gradual enhancements to atomic ops: new atomic*_read_ctrl()
ops, synchronize atomic_{read,set}() ordering requirements between
architectures, add atomic_long_t bitops. (Peter Zijlstra)
- Add _{relaxed|acquire|release}() variants for inc/dec atomics and
use them in various locking primitives: mutex, rtmutex, mcs, rwsem.
This enables weakly ordered architectures (such as arm64) to make
use of more locking related optimizations. (Davidlohr Bueso)
- Implement atomic[64]_{inc,dec}_relaxed() on ARM. (Will Deacon)
- Futex kernel data cache footprint micro-optimization. (Rasmus
Villemoes)
- pvqspinlock runtime overhead micro-optimization. (Waiman Long)
- misc smaller fixlets"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM, locking/atomics: Implement _relaxed variants of atomic[64]_{inc,dec}
locking/rwsem: Use acquire/release semantics
locking/mcs: Use acquire/release semantics
locking/rtmutex: Use acquire/release semantics
locking/mutex: Use acquire/release semantics
locking/asm-generic: Add _{relaxed|acquire|release}() variants for inc/dec atomics
atomic: Implement atomic_read_ctrl()
atomic, arch: Audit atomic_{read,set}()
atomic: Add atomic_long_t bitops
futex: Force hot variables into a single cache line
locking/pvqspinlock: Kick the PV CPU unconditionally when _Q_SLOW_VAL
locking/osq: Relax atomic semantics
locking/qrwlock: Rename ->lock to ->wait_lock
locking/Documentation/lockstat: Fix typo - lokcing -> locking
locking/atomics, cmpxchg: Privatize the inclusion of asm/cmpxchg.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU changes from Ingo Molnar:
"The main changes in this cycle were:
- Improvements to expedited grace periods (Paul E McKenney)
- Performance improvements to and locktorture tests for percpu-rwsem
(Oleg Nesterov, Paul E McKenney)
- Torture-test changes (Paul E McKenney, Davidlohr Bueso)
- Documentation updates (Paul E McKenney)
- Miscellaneous fixes (Paul E McKenney, Boqun Feng, Oleg Nesterov,
Patrick Marlier)"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
fs/writeback, rcu: Don't use list_entry_rcu() for pointer offsetting in bdi_split_work_to_wbs()
rcu: Better hotplug handling for synchronize_sched_expedited()
rcu: Enable stall warnings for synchronize_rcu_expedited()
rcu: Add tasks to expedited stall-warning messages
rcu: Add online/offline info to expedited stall warning message
rcu: Consolidate expedited CPU selection
rcu: Prepare for consolidating expedited CPU selection
cpu: Remove try_get_online_cpus()
rcu: Stop excluding CPU hotplug in synchronize_sched_expedited()
rcu: Stop silencing lockdep false positive for expedited grace periods
rcu: Switch synchronize_sched_expedited() to IPI
locktorture: Fix module unwind when bad torture_type specified
torture: Forgive non-plural arguments
rcutorture: Fix unused-function warning for torturing_tasks()
rcutorture: Fix module unwind when bad torture_type specified
rcu_sync: Cleanup the CONFIG_PROVE_RCU checks
locking/percpu-rwsem: Clean up the lockdep annotations in percpu_down_read()
locking/percpu-rwsem: Fix the comments outdated by rcu_sync
locking/percpu-rwsem: Make use of the rcu_sync infrastructure
locking/percpu-rwsem: Make percpu_free_rwsem() after kzalloc() safe
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI changes from Ingo Molnar:
"The main changes in this cycle were:
- further EFI code generalization to make it more workable for ARM64
- various extensions, such as 64-bit framebuffer address support,
UEFI v2.5 EFI_PROPERTIES_TABLE support
- code modularization simplifications and cleanups
- new debugging parameters
- various fixes and smaller additions"
* 'core-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
efi: Fix warning of int-to-pointer-cast on x86 32-bit builds
efi: Use correct type for struct efi_memory_map::phys_map
x86/efi: Fix kernel panic when CONFIG_DEBUG_VIRTUAL is enabled
efi: Add "efi_fake_mem" boot option
x86/efi: Rename print_efi_memmap() to efi_print_memmap()
efi: Auto-load the efi-pstore module
efi: Introduce EFI_NX_PE_DATA bit and set it from properties table
efi: Add support for UEFIv2.5 Properties table
efi: Add EFI_MEMORY_MORE_RELIABLE support to efi_md_typeattr_format()
efifb: Add support for 64-bit frame buffer addresses
efi/arm64: Clean up efi_get_fdt_params() interface
arm64: Use core efi=debug instead of uefi_debug command line parameter
efi/x86: Move efi=debug option parsing to core
drivers/firmware: Make efi/esrt.c driver explicitly non-modular
efi: Use the generic efi.memmap instead of 'memmap'
acpi/apei: Use appropriate pgprot_t to map GHES memory
arm64, acpi/apei: Implement arch_apei_get_mem_attributes()
arm64/mm: Add PROT_DEVICE_nGnRnE and PROT_NORMAL_WT
acpi, x86: Implement arch_apei_get_mem_attributes()
efi, x86: Rearrange efi_mem_attributes()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull wchan kernel address hiding from Ingo Molnar:
"This fixes a wchan related information leak in /proc/PID/stat.
There's a bit of an ABI twist to it: instead of setting the wchan
field to 0 (which is our usual technique) we set it conditionally to a
0/1 flag to keep ABI compatibility with older procps versions that
only fetches /proc/PID/wchan (symbolic names) if the absolute wchan
address is nonzero"
* 'core-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fs/proc, core/debug: Don't expose absolute kernel addresses via wchan
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- Rework the irqdomain core infrastructure to accomodate ACPI based
systems. This is required to support ARM64 without creating
artificial device tree nodes.
- Sanitize the ACPI based ARM GIC initialization by making use of the
new firmware independent irqdomain core
- Further improvements to the generic MSI management
- Generalize the irq migration on CPU hotplug
- Improvements to the threaded interrupt infrastructure
- Allow the migration of "chained" low level interrupt handlers
- Allow optional force masking of interrupts in disable_irq[_nosysnc]
- Support for two new interrupt chips - Sigh!
- A larger set of errata fixes for ARM gicv3
- The usual pile of fixes, updates, improvements and cleanups all
over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
Document that IRQ_NONE should be returned when IRQ not actually handled
PCI/MSI: Allow the MSI domain to be device-specific
PCI: Add per-device MSI domain hook
of/irq: Use the msi-map property to provide device-specific MSI domain
of/irq: Split of_msi_map_rid to reuse msi-map lookup
irqchip/gic-v3-its: Parse new version of msi-parent property
PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Add support code for multi-parent version of "msi-parent"
irqchip/gic-v3-its: Add handling of PCI requester id.
PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
of/irq: Add new function of_msi_map_rid()
Docs: dt: Add PCI MSI map bindings
irqchip/gic-v2m: Add support for multiple MSI frames
irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
irqchip/mxs: Add Alphascale ASM9260 support
irqchip/mxs: Prepare driver for hardware with different offsets
irqchip/mxs: Panic if ioremap or domain creation fails
irqdomain: Documentation updates
irqdomain/msi: Use fwnode instead of of_node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The timer departement provides:
- More y2038 work in the area of ntp and pps.
- Optimization of posix cpu timers
- New time related selftests
- Some new clocksource drivers
- The usual pile of fixes, cleanups and improvements"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
timeconst: Update path in comment
timers/x86/hpet: Type adjustments
clocksource/drivers/armada-370-xp: Implement ARM delay timer
clocksource/drivers/tango_xtal: Add new timer for Tango SoCs
clocksource/drivers/imx: Allow timer irq affinity change
clocksource/drivers/exynos_mct: Use container_of() instead of this_cpu_ptr()
clocksource/drivers/h8300_*: Remove unneeded memset()s
clocksource/drivers/sh_cmt: Remove unneeded memset() in sh_cmt_setup()
clocksource/drivers/em_sti: Remove unneeded memset()s
clocksource/drivers/mediatek: Use GPT as sched clock source
clockevents/drivers/mtk: Fix spurious interrupt leading to crash
posix_cpu_timer: Reduce unnecessary sighand lock contention
posix_cpu_timer: Convert cputimer->running to bool
posix_cpu_timer: Check thread timers only when there are active thread timers
posix_cpu_timer: Optimize fastpath_timer_check()
timers, kselftest: Add 'adjtick' test to validate adjtimex() tick adjustments
timers: Use __fls in apply_slack()
clocksource: Remove return statement from void functions
net: sfc: avoid using timespec
ntp/pps: use y2038 safe types in pps_event_time
...
|
|
Pull ARM updates from Russell King:
"In this ARM merge, we remove more lines than we add. Changes include:
- Enable imprecise aborts early, so that bus errors aren't masked
until later in the boot. This has the side effect that boot
loaders which provoke these aborts can cause the kernel to crash
early in boot, so we install a handler to report this event around
the site where these are enabled.
- Remove the buggy but impossible to enable cmpxchg syscall code.
- Add unwinding annotations to some assembly code.
- Add support for atomic half-word exchange for ARMv6k+.
- Reduce ioremap() alignment for SMP/LPAE cases where we don't need
the large alignment.
- Addition of an "optimal" 3G configuration for systems with 1G of
RAM.
- Increase vmalloc space by 128M.
- Constify some SMP operations structures, which have never been
writable.
- Improve ARMs dma_mmap() support for mapping DMA coherent mappings
into userspace.
- Fix to the NMI backtrace code in the IPI case on ARM where the
failing CPU gets stuck for 10s waiting for its own IPI to be
delivered.
- Removal of legacy PM support from the AMBA bus driver.
- Another fix for the previous fix of vdsomunge"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (23 commits)
ARM: 8449/1: fix bug in vdsomunge swab32 macro
arm: add missing of_node_put
ARM: 8447/1: catch pending imprecise abort on unmask
ARM: 8446/1: amba: Remove unused callbacks for legacy system PM
ARM: 8443/1: Adding support for atomic half word exchange
ARM: clean up TWD after previous patch
ARM: 8441/2: twd: Don't set CLOCK_EVT_FEAT_C3STOP unconditionally
ARM: 8440/1: remove obsolete documentation
ARM: make highpte an expert option
ARM: 8433/1: add a VMSPLIT_3G_OPT config option
ARM: 8439/1: Fix backtrace generation when IPI is masked
ARM: 8428/1: kgdb: Fix registers on sleeping tasks
ARM: 8427/1: dma-mapping: add support for offset parameter in dma_mmap()
ARM: 8426/1: dma-mapping: add missing range check in dma_mmap()
ARM: remove user cmpxchg syscall
ARM: 8438/1: Add unwinding to __clear_user_std()
ARM: 8436/1: hw_breakpoint: remove unnecessary header
ARM: 8434/2: Revert "7655/1: smp_twd: make twd_local_timer_of_register() no-op for nosmp"
ARM: 8432/1: move VMALLOC_END from 0xff000000 to 0xff800000
ARM: 8430/1: use default ioremap alignment for SMP or LPAE
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- Support for new MM features in ARCv2 cores (THP, PAE40) Some generic
THP bits are touched - all ACKed by Kirill
- Platform framework updates to prepare for EZChip arrival (still in works)
- ARC Public Mailing list setup finally (linux-snps-arc@lists.infraded.org)
* tag 'arc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (42 commits)
ARC: mm: PAE40 support
ARC: mm: PAE40: tlbex.S: Explicitify the size of pte_t
ARC: mm: PAE40: switch to using phys_addr_t for physical addresses
ARC: mm: HIGHMEM: populate high memory from DT
ARC: mm: HIGHMEM: kmap API implementation
ARC: mm: preps ahead of HIGHMEM support #2
ARC: mm: preps ahead of HIGHMEM support
ARC: mm: use generic macros _BITUL()/_AC()
ARC: mm: Improve Duplicate PD Fault handler
MAINTAINERS: Add public mailing list for ARC
ARC: Ensure DT mem base is same as what kernel is built with
ARC: boot: Non Master cpus only need to call EARLY_CPU_SETUP once
ARCv2: smp: [plat-*]: No need to explicitly call mcip_init_smp()
ARC: smp: Introduce smp hook @init_irq_cpu called for all cores
ARC: smp: Rename platform hook @init_smp -> @init_cpu_smp
ARCv2: smp: [plat-*]: No need to explicitly call mcip_init_early_smp()
ARC: smp: Introduce smp hook @init_early_smp for Master core
ARC: remove @init_time, @init_irq platform callbacks
ARC: smp: irqchip: handle IPI as percpu irq like timer
ARC: boot: Support Halt-on-reset and Run-on-reset SMP booting modes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull CRIS changes from Jesper Nilsson:
"Mostly another batch of code removal due to move to standard
frameworks for CRISv32, initial devicetree configuration for a couple
of boards, and some small fixes for kgdb and time handling"
* tag 'cris-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: Drop reference to get_cmos_time()
CRIS: Drop code related to obsolete or unused kconfigs
cris: time: Cleanup of persistent clock stuff
cris: re-use helpers to dump data in hex format
CRIS v32: remove old GPIO and LEDs code
CRIS v32: remove I2C bitbanging driver
CRIS v32: add ARTPEC-3 and P1343 device trees
CRIS v32: dev88: add GPIO, LEDs, RTC, temp sensor
CRIS: add dt-bindings symlink
CRIS v32: increase NR_IRQS
cris: arch-v10: kgdb: Add '__used' for static variable is_dyn_brkp
cris: arch-v10: kgdb: Use BAR instead of DTP0 for register P12
cris: kgdb: use native hex2bin
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32
Pull avr32 update from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: atngw100: remove useless include
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k update from Geert Uytterhoeven.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/sun3: Use %pM format specifier to print ethernet address
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
- Move the out-of-LED-tree led-sead3 driver to the LED subsystem.
- Add 'invert' sysfs attribute to the heartbeat trigger.
- Add Device Tree support to the leds-netxbig driver and add related DT
nodes to the kirkwood-netxbig.dtsi and kirkwood-net5big.dts files.
Remove static LED setup from the related board files.
- Remove redundant brightness conversion operation from leds-netxbig.
- Improve leds-bcm6328 driver: improve default-state handling, add more
init configuration options, print invalid LED instead of warning only
about maximum LED value.
- Add a shutdown function for setting gpio-leds into off state when
shutting down.
- Fix DT flash timeout property naming in leds-aat1290.txt.
- Switch to using devm prefixed version of led_classdev_register()
(leds-cobalt-qube, leds-hp6xx, leds-ot200, leds-ipaq-micro,
leds-netxbig, leds-locomo, leds-menf21bmc, leds-net48xx, leds-wrap).
- Add missing of_node_put (leds-powernv, leds-bcm6358, leds-bcm6328,
leds-88pm860x).
- Coding style fixes and cleanups: led-class/led-core, leds-ipaq-micro.
* tag 'leds_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (27 commits)
leds: 88pm860x: add missing of_node_put
leds: bcm6328: add missing of_node_put
leds: bcm6358: add missing of_node_put
powerpc/powernv: add missing of_node_put
leds: leds-wrap.c: Use devm_led_classdev_register
leds: aat1290: Fix property naming of flash-timeout-us
leds: leds-net48xx: Use devm_led_classdev_register
leds: leds-menf21bmc.c: Use devm_led_class_register
leds: leds-locomo.c: Use devm_led_classdev_register
leds: leds-gpio: add shutdown function
Documentation: leds: update DT bindings for leds-bcm6328
leds-bcm6328: add more init configuration options
leds-bcm6328: simplify and improve default-state handling
leds-bcm6328: print invalid LED
leds: netxbig: set led_classdev max_brightness
leds: netxbig: convert to use the devm_ functions
ARM: mvebu: remove static LED setup for netxbig boards
ARM: Kirkwood: add LED DT entries for netxbig boards
leds: netxbig: add device tree binding
leds: triggers: add invert to heartbeat
...
|
|
Commit 7d7355f58ba4 ("sh_eth: Ensure proper ordering of descriptor active
bit write/read") did the right thing but used too "heavy" barriers while
there were already "lighter" DMA barriers exactly for this case...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Caller passing down the SKIP_EOPNOTSUPP switchdev flag expects that
-EOPNOTSUPP cannot be returned. But in case of direct op call without
recurtion, this may happen. So fix this by checking it always on the
end of __switchdev_port_attr_set function.
Fixes: 464314ea6c11 ("switchdev: skip over ports returning -EOPNOTSUPP when recursing ports")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It looks like this has never been used at all.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"irlmp_unregister_service"
The irlmp_unregister_service() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver uses 'struct timeval' which we are trying to remove since
32 bit time types will break in the year 2038 by replacing it with
ktime_t.
This patch changes do_gettimeofday() to ktime_get() because
ktime_get() returns a ktime_t while do_gettimeofday() returns struct
timeval.
This patch also uses ktime_us_delta() to get the elapsed time.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Another set of fixes:
* remove a warning on a check that can trigger without any
errors having happened (Andrei)
* correctly handle deauth request while in the process of
associating (Andrei)
* fix TDLS HT operation (Arik)
* allow changing AID/listen interval during client setup (Ayala)
* be more forgiving with WMM parameters to get HT/VHT in case of
broken APs with bad WMM settings (Emmanuel, myself)
* a number of other fixes (some in documentation)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA ports must be members of a VLAN in order to ensure frame bridging
between chained switch chips.
Thus tag them in addition to the CPU port when adding a VLAN, and skip
them when deleting a VLAN and reporting VLAN members.
Also use the UNMODIFIED egress policy, so that frames egress on these
ports as they ingress, tagged or untagged.
Fixes: 0d3b33e60206 ("net: dsa: mv88e6xxx: add VLAN Load support")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Frames with DSA headers passing to/from the CPU were taking place in the
MAC learning on these ports, resulting in incorrect ATU entries. Disable
learning on these ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As pointed out by Nikolay and further explained by Geert, the initial
for_each_netdev_feature macro was broken, as feature would get set outside
of the block of code it was intended to run in, thus only ever working for
the first feature bit in the mask. While less pretty this way, this is
tested and confirmed functional with multiple feature bits set in
NETIF_F_UPPER_DISABLES.
[root@dell-per730-01 ~]# ethtool -K bond0 lro off
...
[ 242.761394] bond0: Disabling feature 0x0000000000008000 on lower dev p5p2.
[ 243.552178] bnx2x 0000:06:00.1 p5p2: using MSI-X IRQs: sp 74 fp[0] 76 ... fp[7] 83
[ 244.353978] bond0: Disabling feature 0x0000000000008000 on lower dev p5p1.
[ 245.147420] bnx2x 0000:06:00.0 p5p1: using MSI-X IRQs: sp 62 fp[0] 64 ... fp[7] 71
[root@dell-per730-01 ~]# ethtool -K bond0 gro off
...
[ 251.925645] bond0: Disabling feature 0x0000000000004000 on lower dev p5p2.
[ 252.713693] bnx2x 0000:06:00.1 p5p2: using MSI-X IRQs: sp 74 fp[0] 76 ... fp[7] 83
[ 253.499085] bond0: Disabling feature 0x0000000000004000 on lower dev p5p1.
[ 254.290922] bnx2x 0000:06:00.0 p5p1: using MSI-X IRQs: sp 62 fp[0] 64 ... fp[7] 71
Fixes: fd867d51f ("net/core: generic support for disabling netdev features down stack")
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Nikolay Aleksandrov <razor@blackwall.org>
CC: Michal Kubecek <mkubecek@suse.cz>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NIC drivers mark device as detached during error recovery.
It expects no manangement hooks to be invoked in this state.
Invoke driver vlan hooks only if device is present.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The newly added led trigger support in the com20020-pci driver causes
build errors when CONFIG_LEDS_CLASS is disabled:
drivers/built-in.o: In function `com20020pci_probe':
(.text+0x185dc4): undefined reference to `devm_led_classdev_register'
(.text+0x185dd8): undefined reference to `devm_led_classdev_register'
This adds a Kconfig dependency to prevent the invalid configurations.
Other drivers appear to be split 50:50 between 'select' and 'depends on'
for this symbol, I picked 'depends on' as I could not find a common
policy and it generally causes fewer problems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 8890624a4e8c ("arcnet: com20020-pci: add led trigger support")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The verbose() printer dumps the verifier state to user space, so let gcc
take care to check calls to verbose() for (future) errors. make with W=1
correctly suggests: function might be possible candidate for 'gnu_printf'
format attribute [-Wsuggest-attribute=format].
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stefan Sørensen says:
====================
dp83640 driver fixes
This series fixes a number of minor bugs in the dp83640 driver.
====================
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the packet timestamping function, check that the ptp version and
protocol of the packet matches what we have configured the hardware to
actually generate timestamps for, before looking/waiting for a timestamp.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the definition of PTP_CLASS_L2 to not have any bits overlapping with
the other defined protocol values, allowing the PTP_CLASS_* definitions to
be for simple filtering on packet type.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The list of rx timestamps are currently only pruned of old entries when a
new entry is inserted. If no new entries are added, old timestamps may
survive beyond their lifetime, possible causing them to be attached to
packets with the same sequence number after a rollover.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently rx_timestamp_work reschedules itself as a regular workqueue item,
effectively causing it run constantly as long as there are packets left in
the queue. Fix by using delayed workqueue items, limiting it to run only
every two jiffies.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only using the message type and sequence id for matching timestamps
with packets is error prone, as multiple clients may very well be
sending packets with the same messagetype and timestamp at the same
time. Fix by extending the check to include the hash of bytes 20-29
(source id in PTPv2) that is provided with the timestamps.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both tunnel6_protocol and tunnel46_protocol share the same error
handler, tunnel6_err(), which traverses through tunnel6_handlers list.
For ipip6 tunnels, we need to traverse tunnel46_handlers as we do e.g.
in tunnel46_rcv(). Current code can generate an ICMPv6 error message
with an IPv4 packet embedded in it.
Fixes: 73d605d1abbd ("[IPSEC]: changing API of xfrm6_tunnel_register")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|