summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2006-11-15Linux 2.6.19-rc6v2.6.19-rc6Linus Torvalds1-1/+1
Getting there. Hopefully the MSI and other interrupt problems are all solved now. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-15[PATCH] powerpc: windfarm shall request it's sub modulesBenjamin Herrenschmidt3-0/+13
The windfarm code, in it's current incarnation, uses request_module() to load the various submodules it needs for a given platform so that only the main platform control module needs to be modprobed. However, it was missing various bits. This fixes it. In the future, we'll use some hotplug mecanisms to try to get all of this auto-loaded on the platforms where it matters but that isn't ready yet. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-16[POWERPC] Wire up sys_move_pagesStephen Rothwell2-1/+3
All the infrastructure is already in place for this, so we only need to allocate a syscall number and hook it up. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-11-16[POWERPC] Add the thread_siblings files to sysfsStephen Rothwell1-1/+7
This adds the /sys/devices/system/cpu/*/topology/thread_siblings files on powerpc. These files are already available on other architectures. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-11-15[PATCH] Use delayed disable mode of ioapic edge triggered interruptsEric W. Biederman2-2/+6
Komuro reports that ISA interrupts do not work after a disable_irq(), causing some PCMCIA drivers to not work, with messages like eth0: Asix AX88190: io 0x300, irq 3, hw_addr xx:xx:xx:xx:xx:xx eth0: found link beat eth0: autonegotiation complete: 100baseT-FD selected eth0: interrupt(s) dropped! eth0: interrupt(s) dropped! eth0: interrupt(s) dropped! ... Linus Torvalds <torvalds@osdl.org> said: "Now, edge-triggered interrupts are a _lot_ harder to mask, because the Intel APIC is an unbelievable piece of sh*t, and has the edge-detect logic _before_ the mask logic, so if a edge happens _while_ the device is masked, you'll never ever see the edge ever again (unmasking will not cause a new edge, so you simply lost the interrupt). So when you "mask" an edge-triggered IRQ, you can't really mask it at all, because if you did that, you'd lose it forever if the IRQ comes in while you masked it. Instead, we're supposed to leave it active, and set a flag, and IF the IRQ comes in, we just remember it, and mask it at that point instead, and then on unmasking, we have to replay it by sending a self-IPI." This trivial patch solves the problem. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Ingo Molnar <mingo@redhat.com> Acked-by: Komuro <komurojun-mbn@nifty.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] ALSA: hda-intel - Disable MSI support by defaultTakashi Iwai2-5/+5
Disable MSI support on HD-audio driver as default since there are too many broken devices. The module option is changed from disable_msi to enable_msi, too. For turning MSI support on, pass enable_msi=1, instead. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] Char: isicom, fix close bugJiri Slaby1-1/+2
port is dereferenced even if it is NULL. Dereference it _after_ the check if (!port)... Thanks Eric <ef87@yahoo.com> for reporting this. This fixes http://bugzilla.kernel.org/show_bug.cgi?id=7527 Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14Merge branch 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6Linus Torvalds17-75/+86
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: [PATCH] x86-64: Fix race in exit_idle [PATCH] x86-64: Fix vgetcpu when CONFIG_HOTPLUG_CPU is disabled [PATCH] x86: Add acpi_user_timer_override option for Asus boards [PATCH] x86-64: setup saved_max_pfn correctly (kdump) [PATCH] x86-64: Handle reserve_bootmem_generic beyond end_pfn [PATCH] x86-64: shorten the x86_64 boot setup GDT to what the comment says [PATCH] x86-64: Fix PTRACE_[SG]ET_THREAD_AREA regression with ia32 emulation. [PATCH] x86-64: Fix partial page check to ensure unusable memory is not being marked usable. Revert "[PATCH] MMCONFIG and new Intel motherboards"
2006-11-14Revert "[PATCH] fix Data Acess error in dup_fd"Linus Torvalds1-1/+0
This reverts commit 0130b0b32ee53dc7add773fcea984f6a26ef1da3. Sergey Vlasov points out (and Vadim Lobanov concurs) that the bug it was supposed to fix must be some unrelated memory corruption, and the "fix" actually causes more problems: "However, the new code does not look safe in all cases. If some other task has opened more files while dup_fd() released oldf->file_lock, the new code will update open_files to the new larger value. But newf was allocated with the old smaller value of open_files, therefore subsequent accesses to newf may try to write into unallocated memory." so revert it. Cc: Sharyathi Nagesh <sharyath@in.ibm.com> Cc: Sergey Vlasov <vsu@altlinux.ru> Cc: Vadim Lobanov <vlobanov@speakeasy.net> Cc: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14Merge branch 'upstream-linus' of ↵Linus Torvalds3-5/+18
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: libata: fix double-completion on error [PATCH] pata_artop: fix "& (1 >>" typo [PATCH] hpt37x: Check the enablebits
2006-11-14[PATCH] hugetlb: fix error return for brk() entering a hugepage regionHugh Dickins1-3/+2
Commit cb07c9a1864a8eac9f3123e428100d5b2a16e65a causes the wrong return value. is_hugepage_only_range() is a boolean, so we should return -EINVAL rather than 1. Also - we can use "mm" instead of looking up "current->mm" again. Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] cpqarray: fix iostatJens Axboe1-4/+11
cpqarray needs to call disk_stat_add() for iostat to work. Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] cciss: fix iostatJens Axboe1-0/+6
cciss needs to call disk_stat_add() for iostat to work. Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] libata: Convert from module_init to subsys_initcallBrian King1-1/+1
When building a monolithic kernel, the load order of drivers does not work for SAS libata users, resulting in a kernel oops. Convert libata to use subsys_initcall instead of module_init, which ensures that libata gets loaded before any LLDD. This is the same thing that scsi core does to solve the problem. The load order problem was observed on ipr SAS adapters and should exist for other SAS users as well. Signed-off-by: Brian King <brking@us.ibm.com> Acked-by: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] hugetlb: check for brk() entering a hugepage regionDavid Gibson1-0/+4
Unlike mmap(), the codepath for brk() creates a vma without first checking that it doesn't touch a region exclusively reserved for hugepages. On powerpc, this can allow it to create a normal page vma in a hugepage region, causing oopses and other badness. Add a test to prevent this. With this patch, brk() will simply fail if it attempts to move the break into a hugepage reserved region. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Cc: Adam Litke <agl@us.ibm.com> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] hugetlb: prepare_hugepage_range check offset tooHugh Dickins5-20/+25
(David:) If hugetlbfs_file_mmap() returns a failure to do_mmap_pgoff() - for example, because the given file offset is not hugepage aligned - then do_mmap_pgoff will go to the unmap_and_free_vma backout path. But at this stage the vma hasn't been marked as hugepage, and the backout path will call unmap_region() on it. That will eventually call down to the non-hugepage version of unmap_page_range(). On ppc64, at least, that will cause serious problems if there are any existing hugepage pagetable entries in the vicinity - for example if there are any other hugepage mappings under the same PUD. unmap_page_range() will trigger a bad_pud() on the hugepage pud entries. I suspect this will also cause bad problems on ia64, though I don't have a machine to test it on. (Hugh:) prepare_hugepage_range() should check file offset alignment when it checks virtual address and length, to stop MAP_FIXED with a bad huge offset from unmapping before it fails further down. PowerPC should apply the same prepare_hugepage_range alignment checks as ia64 and all the others do. Then none of the alignment checks in hugetlbfs_file_mmap are required (nor is the check for too small a mapping); but even so, move up setting of VM_HUGETLB and add a comment to warn of what David Gibson discovered - if hugetlbfs_file_mmap fails before setting it, do_mmap_pgoff's unmap_region when unwinding from error will go the non-huge way, which may cause bad behaviour on architectures (powerpc and ia64) which segregate their huge mappings into a separate region of the address space. Signed-off-by: Hugh Dickins <hugh@veritas.com> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: "David S. Miller" <davem@davemloft.net> Acked-by: Adam Litke <agl@us.ibm.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] usb: MAINTAINERS updatesDavid Brownell1-1/+9
Looks like I still take care of the USB gadget/peripheral framework. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] nvidiafb: fix unreachable code in nv10GetConfigNathan Lynch1-1/+1
Fix binary/logical operator typo which leads to unreachable code. Noticed while looking at other issues; I don't have the relevant hardware to test this. Signed-off-by: Nathan Lynch <ntl@pobox.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Acked-by: James Simmons <jsimmons@infradead.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] autofs4: panic after mount failIan Kent4-6/+32
Resolve the panic on failed mount of an autofs filesystem originally reported by Mao Bibo. It addresses two issues that happen after the mount fail. The first a NULL pointer reference to a field (pipe) in the autofs superblock info structure and second the lack of super block cleanup by the autofs and autofs4 modules. Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] drivers/ide: stray bracketNicolas Kaiser1-1/+1
Stray bracket in debug code. Signed-off-by: Nicolas Kaiser <nikai@nikai.net> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] revert "PCI: quirk for IBM Dock II cardbus controllers"Andrew Morton1-27/+0
Fix http://bugzilla.kernel.org/show_bug.cgi?id=7264 We need to target this quirk a little more tightly, using the T20 DMI string. Cc: Pavel Kysilka <goldenfish@bsys.cz> Acked-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] fix via586 irq routing for pirq 5Daniel Ritz1-2/+2
Fix interrupt routing for via 586 bridges. pirq can be 5 which needs to be mapped to INTD. But currently the access functions can handle only pirq 1-4. this is similar to the other via chipsets where pirq 4 and 5 are both mapped to INTD. Fixes bugzilla #7490 Cc: Daniel Paschka <monkey20181@gmx.net> Cc: Adrian Bunk <bunk@susta.de> Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] setup_irq(): better mismatch debuggingAndrew Morton1-2/+7
When we get a mismatch between handlers on the same IRQ, all we get is "IRQ handler type mismatch for IRQ n". Let's print the name of the presently-registered handler with which we got the mismatch. Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-14[PATCH] x86-64: Fix race in exit_idleAndi Kleen2-2/+10
When another interrupt happens in exit_idle the exit idle notifier could be called an incorrect number of times. Add a test_and_clear_bit_pda and use it handle the bit atomically against interrupts to avoid this. Pointed out by Stephane Eranian Signed-off-by: Andi Kleen <ak@suse.de>
2006-11-14[PATCH] x86-64: Fix vgetcpu when CONFIG_HOTPLUG_CPU is disabledAndi Kleen4-35/+26
The vgetcpu per CPU initialization previously relied on CPU hotplug events for all CPUs to initialize the per CPU state. That only worked only on kernels with CONFIG_HOTPLUG_CPU enabled. On the others some CPUs didn't get their state initialized properly and vgetcpu wouldn't work. Change the initialization sequence to instead run in a normal initcall (which runs after the normal CPU bootup) and initialize all running CPUs there. Later hotplug CPUs are still handled with an hotplug notifier. This actually simplifies the code somewhat. Signed-off-by: Andi Kleen <ak@suse.de>
2006-11-14[PATCH] x86: Add acpi_user_timer_override option for Asus boardsAndi Kleen6-1/+29
Timer overrides are normally disabled on Nvidia board because they are commonly wrong, except on new ones with HPET support. Unfortunately there are quite some Asus boards around that don't have HPET, but need a timer override. We don't know yet how to handle this transparently, but at least add a command line option to force the timer override and let them boot. Cc: len.brown@intel.com Signed-off-by: Andi Kleen <ak@suse.de>
2006-11-14[PATCH] x86-64: setup saved_max_pfn correctly (kdump)Magnus Damm1-0/+2
x86_64: setup saved_max_pfn correctly 2.6.19-rc4 has broken CONFIG_CRASH_DUMP support on x86_64. It is impossible to read out the kernel contents from /proc/vmcore because saved_max_pfn is set to zero instead of the max_pfn value before the user map is setup. This happens because saved_max_pfn is initialized at parse_early_param() time, and at this time no active regions have been registered. save_max_pfn is setup from e820_end_of_ram(), more exact find_max_pfn_with_active_regions() which returns 0 because no regions exist. This patch fixes this by registering before and removing after the call to e820_end_of_ram(). Signed-off-by: Magnus Damm <magnus@valinux.co.jp> Signed-off-by: Andi Kleen <ak@suse.de>
2006-11-14[PATCH] x86-64: Handle reserve_bootmem_generic beyond end_pfnAndi Kleen1-1/+14
This can happen on kexec kernels with some configurations, in particularly on Unisys ES7000 systems. Analysis by Amul Shah Cc: Amul Shah <amul.shah@unisys.com> Signed-off-by: Andi Kleen <ak@suse.de>
2006-11-14[PATCH] x86-64: shorten the x86_64 boot setup GDT to what the comment saysSteven Rostedt1-3/+2
Stephen Tweedie, Herbert Xu, and myself have been struggling with a very nasty bug in Xen. But it also pointed out a small bug in the x86_64 kernel boot setup. The GDT limit being setup by the initial bzImage code when entering into protected mode is way too big. The comment by the code states that the size of the GDT is 2048, but the actual size being set up is much bigger (32768). This happens simply because of one extra '0'. Instead of setting up a 0x800 size, 0x8000 is set up. On bare metal this is fine because the CPU wont load any segments unless they are explicitly used. But unfortunately, this breaks Xen on vmx FV, since it (for now) blindly loads all the segments into the VMCS if they are less than the gdt limit. Since the real mode segments are around 0x3000, we are getting junk into the VMCS and that later causes an exception. Stephen Tweedie has written up a patch to fix the Xen side and will be submitting that to those folks. But that doesn't excuse the GDT limit being a magnitude too big. AK: changed to compute true gdt size in assembler, fixed comment Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andi Kleen <ak@suse.de>
2006-11-14[PATCH] x86-64: Fix PTRACE_[SG]ET_THREAD_AREA regression with ia32 emulation.Andi Kleen1-0/+2
ptrace(PTRACE_[SG]ET_THREAD_AREA) calls from ia32 code should be passed onto the x86_64 implementation. The default case in sys32_ptrace used to call to sys_ptrace(), but is now EINVAL. This patch fixes a regression caused by that changed. Signed-off-by: Mike McCormack <mike@codeweavers.com> Signed-off-by: Andi Kleen <ak@suse.de>
2006-11-14[PATCH] x86-64: Fix partial page check to ensure unusable memory is not ↵Aaron Durbin1-1/+1
being marked usable. Fix partial page check in e820_register_active_regions to ensure partial pages are not being marked as active in the memory pool. Signed-off-by: Aaron Durbin <adurbin@google.com> Signed-off-by: Andi Kleen <ak@suse.de>
2006-11-14Revert "[PATCH] MMCONFIG and new Intel motherboards"Andi Kleen1-32/+0
This reverts 4c6e052adfe285ede5884e4e8c4d33af33932c13 commit. Following Linus' i386 change: revert resource reservation for mmcfg config now. Will be revisited in .20 hopefully.
2006-11-14libata: fix double-completion on errorDarrick J. Wong1-1/+1
A curious thing happens, however, when ata_qc_new_init fails to get an ata_queued_cmd: First, ata_qc_new_init handles the failure like this: cmd->result = (DID_OK << 16) | (QUEUE_FULL << 1); done(cmd); Then, we return to ata_scsi_translate and do this: err_mem: cmd->result = (DID_ERROR << 16); done(cmd); It appears to me that first we set a status code indicating that we're ok but the device queue is full and finish the command, but then we blow away that status code and replace it with an error flag and finish the command a second time! That does not seem to be desirable behavior since we merely want the I/O to wait until a command slot frees up, not send errors up the block layer. In the err_mem case, we should simply exit out of ata_scsi_translate instead. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-14[PATCH] pata_artop: fix "& (1 >>" typoAlexey Dobriyan1-1/+1
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-14[PATCH] hpt37x: Check the enablebitsAlan Cox1-3/+16
Helps for PATA but SATA bridged devices lie and always set all the bits so will need the error handling fixes from Tejun. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-13Merge branch 'for-linus' of ↵Linus Torvalds1-2/+17
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: MMC: Do not set unsupported bits in OCR response MMC: Poll card status after rescanning cards
2006-11-13Merge branch 'for-linus' of ↵Linus Torvalds13-61/+111
master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband * 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: IB/mad: Fix race between cancel and receive completion RDMA/amso1100: Fix && typo RDMA/amso1100: Fix unitialized pseudo_netdev accessed in c2_register_device IB/ehca: Activate scaling code by default IB/ehca: Use named constant for max mtu IB/ehca: Assure 4K alignment for firmware control blocks
2006-11-13[dvb saa7134] Fix missing 'break' for avermedia card caseLinus Torvalds1-0/+1
Commit 450efcfd2e1d941e302a8c89322fbfcef237be98 broke Avermedia 777 support. Added obvious missing "break" statement. Cc: José Suárez <j.suarez.agapito@gmail.com> Cc: Michael Krufky <mkrufky@linuxtv.org> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-13[PATCH] ide-cd: only set rq->errors SCSI style for block pc requestsJens Axboe1-1/+1
We should only set ->errors to CHECK_CONDITION and so on for requests that use this field in the SCSI manner. Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-13[PATCH] Fix bad data direction in SG_IOJens Axboe1-1/+1
Contrary to what the name misleads you to believe, SG_DXFER_TO_FROM_DEV is really just a normal read seen from the device side. This patch fixes http://lkml.org/lkml/2006/10/13/100 Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-13IB/mad: Fix race between cancel and receive completionRoland Dreier1-1/+1
When ib_cancel_mad() is called, it puts the canceled send on a list and schedules a "flushed" callback from process context. However, this leaves a window where a receive completion could be processed before the send is fully flushed. This is fine, except that ib_find_send_mad() will find the MAD and return it to the receive processing, which results in the sender getting both a successful receive and a "flushed" send completion for the same request. Understandably, this confuses the sender, which is expecting only one of these two callbacks, and leads to grief such as a use-after-free in IPoIB. Fix this by changing ib_find_send_mad() to return a send struct only if the status is still successful (and not "flushed"). The search of the send_list already had this check, so this patch just adds the same check to the search of the wait_list. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-11-13RDMA/amso1100: Fix && typoJean Delvare1-2/+2
Fix the AMSO1100 firmware version computation, which was broken due to "&&" being used where "&" should have. Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-11-13RDMA/amso1100: Fix unitialized pseudo_netdev accessed in c2_register_deviceTom Tucker2-20/+22
Rework some load-time error handling: c2_register_device() leaked when it failed, and the function that called it didn't check the return code. Signed-off-by: Tom Tucker <tom@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-11-13IB/ehca: Activate scaling code by defaultHoang-Nam Nguyen1-0/+1
Change ehca's Kconfig to activates scaling code as default. After several measurements we saw that this feature prevents dropped packets (UD) in stress situation. Thus, enabling it helps to improve ehca's bandwidth through IPoIB. Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-11-13IB/ehca: Use named constant for max mtuHoang-Nam Nguyen2-3/+4
Define and use a constant EHCA_MAX_MTU instead hardcoded value. Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-11-13Merge branch 'master' of ↵Linus Torvalds8-10/+25
master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb * 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: V4L/DVB (4818): Flexcop-usb: fix debug printk V4L/DVB (4817): Fix uses of "&&" where "&" was intended V4L/DVB (4816): Change tuner type for Avermedia A16AR V4L/DVB (4815): Remote support for Avermedia A16AR V4L/DVB (4814): Remote support for Avermedia 777 V4L/DVB (4804): Fix missing i2c dependency for saa7110 V4L/DVB (4802): Cx88: fix remote control on WinFast 2000XP Expert V4L/DVB (4795): Tda826x: use correct max frequency
2006-11-13Merge branch 'merge' of ↵Linus Torvalds8-31/+88
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: [POWERPC] cell: set ARCH_SPARSEMEM_DEFAULT in Kconfig [POWERPC] Fix cell "new style" mapping and add debug [POWERPC] pseries: Force 4k update_flash block and list sizes [POWERPC] CPM_UART: Fix non-console initialisation [POWERPC] CPM_UART: Fix non-console transmit [POWERPC] Make sure initrd and dtb sections get into zImage correctly
2006-11-13Merge git://oss.sgi.com:8090/xfs/xfs-2.6Linus Torvalds15-113/+189
* git://oss.sgi.com:8090/xfs/xfs-2.6: [XFS] Remove KERNEL_VERSION macros from xfs_dmapi.h [XFS] Prevent a deadlock when xfslogd unpins inodes. [XFS] Clean up i_flags and i_flags_lock handling. [XFS] 956664: dm_read_invis() changes i_atime [XFS] rename uio_read() to xfs_uio_read() [XFS] Keep lockdep happy. [XFS] 956618: Linux crashes on boot with XFS-DMAPI filesystem when
2006-11-13Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds4-6/+7
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [IPVS]: More endianness fixed. [IPVS]: Compile fix for annotations in userland.
2006-11-13Merge master.kernel.org:/pub/scm/linux/kernel/git/sfrench/cifs-2.6Linus Torvalds3-13/+22
* master.kernel.org:/pub/scm/linux/kernel/git/sfrench/cifs-2.6: [CIFS] Fix minor problem with previous patch [CIFS] Fix mount failure when domain not specified [CIFS] Explicitly set stat->blksize [CIFS] NFS stress test generates flood of "close with pending write" messages
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-22 07:53:01 +0000