diff options
Diffstat (limited to 'drivers/mmc/host')
| -rw-r--r-- | drivers/mmc/host/cqhci-core.c | 44 | ||||
| -rw-r--r-- | drivers/mmc/host/meson-mx-sdhc-mmc.c | 26 | ||||
| -rw-r--r-- | drivers/mmc/host/sdhci-pci-gli.c | 54 | ||||
| -rw-r--r-- | drivers/mmc/host/sdhci-sprd.c | 35 |
4 files changed, 88 insertions, 71 deletions
diff --git a/drivers/mmc/host/cqhci-core.c b/drivers/mmc/host/cqhci-core.c index b3d7d6d8d654..41e94cd14109 100644 --- a/drivers/mmc/host/cqhci-core.c +++ b/drivers/mmc/host/cqhci-core.c @@ -942,8 +942,8 @@ static bool cqhci_clear_all_tasks(struct mmc_host *mmc, unsigned int timeout) ret = cqhci_tasks_cleared(cq_host); if (!ret) - pr_debug("%s: cqhci: Failed to clear tasks\n", - mmc_hostname(mmc)); + pr_warn("%s: cqhci: Failed to clear tasks\n", + mmc_hostname(mmc)); return ret; } @@ -976,7 +976,7 @@ static bool cqhci_halt(struct mmc_host *mmc, unsigned int timeout) ret = cqhci_halted(cq_host); if (!ret) - pr_debug("%s: cqhci: Failed to halt\n", mmc_hostname(mmc)); + pr_warn("%s: cqhci: Failed to halt\n", mmc_hostname(mmc)); return ret; } @@ -984,10 +984,10 @@ static bool cqhci_halt(struct mmc_host *mmc, unsigned int timeout) /* * After halting we expect to be able to use the command line. We interpret the * failure to halt to mean the data lines might still be in use (and the upper - * layers will need to send a STOP command), so we set the timeout based on a - * generous command timeout. + * layers will need to send a STOP command), however failing to halt complicates + * the recovery, so set a timeout that would reasonably allow I/O to complete. */ -#define CQHCI_START_HALT_TIMEOUT 5 +#define CQHCI_START_HALT_TIMEOUT 500 static void cqhci_recovery_start(struct mmc_host *mmc) { @@ -1075,28 +1075,28 @@ static void cqhci_recovery_finish(struct mmc_host *mmc) ok = cqhci_halt(mmc, CQHCI_FINISH_HALT_TIMEOUT); - if (!cqhci_clear_all_tasks(mmc, CQHCI_CLEAR_TIMEOUT)) - ok = false; - /* * The specification contradicts itself, by saying that tasks cannot be * cleared if CQHCI does not halt, but if CQHCI does not halt, it should * be disabled/re-enabled, but not to disable before clearing tasks. * Have a go anyway. */ - if (!ok) { - pr_debug("%s: cqhci: disable / re-enable\n", mmc_hostname(mmc)); - cqcfg = cqhci_readl(cq_host, CQHCI_CFG); - cqcfg &= ~CQHCI_ENABLE; - cqhci_writel(cq_host, cqcfg, CQHCI_CFG); - cqcfg |= CQHCI_ENABLE; - cqhci_writel(cq_host, cqcfg, CQHCI_CFG); - /* Be sure that there are no tasks */ - ok = cqhci_halt(mmc, CQHCI_FINISH_HALT_TIMEOUT); - if (!cqhci_clear_all_tasks(mmc, CQHCI_CLEAR_TIMEOUT)) - ok = false; - WARN_ON(!ok); - } + if (!cqhci_clear_all_tasks(mmc, CQHCI_CLEAR_TIMEOUT)) + ok = false; + + /* Disable to make sure tasks really are cleared */ + cqcfg = cqhci_readl(cq_host, CQHCI_CFG); + cqcfg &= ~CQHCI_ENABLE; + cqhci_writel(cq_host, cqcfg, CQHCI_CFG); + + cqcfg = cqhci_readl(cq_host, CQHCI_CFG); + cqcfg |= CQHCI_ENABLE; + cqhci_writel(cq_host, cqcfg, CQHCI_CFG); + + cqhci_halt(mmc, CQHCI_FINISH_HALT_TIMEOUT); + + if (!ok) + cqhci_clear_all_tasks(mmc, CQHCI_CLEAR_TIMEOUT); cqhci_recover_mrqs(cq_host); diff --git a/drivers/mmc/host/meson-mx-sdhc-mmc.c b/drivers/mmc/host/meson-mx-sdhc-mmc.c index 528ec8166e7c..1ed9731e77ef 100644 --- a/drivers/mmc/host/meson-mx-sdhc-mmc.c +++ b/drivers/mmc/host/meson-mx-sdhc-mmc.c @@ -269,7 +269,7 @@ static int meson_mx_sdhc_enable_clks(struct mmc_host *mmc) static int meson_mx_sdhc_set_clk(struct mmc_host *mmc, struct mmc_ios *ios) { struct meson_mx_sdhc_host *host = mmc_priv(mmc); - u32 rx_clk_phase; + u32 val, rx_clk_phase; int ret; meson_mx_sdhc_disable_clks(mmc); @@ -290,27 +290,11 @@ static int meson_mx_sdhc_set_clk(struct mmc_host *mmc, struct mmc_ios *ios) mmc->actual_clock = clk_get_rate(host->sd_clk); /* - * according to Amlogic the following latching points are - * selected with empirical values, there is no (known) formula - * to calculate these. + * Phase 90 should work in most cases. For data transmission, + * meson_mx_sdhc_execute_tuning() will find a accurate value */ - if (mmc->actual_clock > 100000000) { - rx_clk_phase = 1; - } else if (mmc->actual_clock > 45000000) { - if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) - rx_clk_phase = 15; - else - rx_clk_phase = 11; - } else if (mmc->actual_clock >= 25000000) { - rx_clk_phase = 15; - } else if (mmc->actual_clock > 5000000) { - rx_clk_phase = 23; - } else if (mmc->actual_clock > 1000000) { - rx_clk_phase = 55; - } else { - rx_clk_phase = 1061; - } - + regmap_read(host->regmap, MESON_SDHC_CLKC, &val); + rx_clk_phase = FIELD_GET(MESON_SDHC_CLKC_CLK_DIV, val) / 4; regmap_update_bits(host->regmap, MESON_SDHC_CLK2, MESON_SDHC_CLK2_RX_CLK_PHASE, FIELD_PREP(MESON_SDHC_CLK2_RX_CLK_PHASE, diff --git a/drivers/mmc/host/sdhci-pci-gli.c b/drivers/mmc/host/sdhci-pci-gli.c index d8a991b349a8..77911a57b12c 100644 --- a/drivers/mmc/host/sdhci-pci-gli.c +++ b/drivers/mmc/host/sdhci-pci-gli.c @@ -1189,6 +1189,32 @@ static void gl9763e_hs400_enhanced_strobe(struct mmc_host *mmc, sdhci_writel(host, val, SDHCI_GLI_9763E_HS400_ES_REG); } +static void gl9763e_set_low_power_negotiation(struct sdhci_pci_slot *slot, + bool enable) +{ + struct pci_dev *pdev = slot->chip->pdev; + u32 value; + + pci_read_config_dword(pdev, PCIE_GLI_9763E_VHS, &value); + value &= ~GLI_9763E_VHS_REV; + value |= FIELD_PREP(GLI_9763E_VHS_REV, GLI_9763E_VHS_REV_W); + pci_write_config_dword(pdev, PCIE_GLI_9763E_VHS, value); + + pci_read_config_dword(pdev, PCIE_GLI_9763E_CFG, &value); + + if (enable) + value &= ~GLI_9763E_CFG_LPSN_DIS; + else + value |= GLI_9763E_CFG_LPSN_DIS; + + pci_write_config_dword(pdev, PCIE_GLI_9763E_CFG, value); + + pci_read_config_dword(pdev, PCIE_GLI_9763E_VHS, &value); + value &= ~GLI_9763E_VHS_REV; + value |= FIELD_PREP(GLI_9763E_VHS_REV, GLI_9763E_VHS_REV_R); + pci_write_config_dword(pdev, PCIE_GLI_9763E_VHS, value); +} + static void sdhci_set_gl9763e_signaling(struct sdhci_host *host, unsigned int timing) { @@ -1297,6 +1323,9 @@ static int gl9763e_add_host(struct sdhci_pci_slot *slot) if (ret) goto cleanup; + /* Disable LPM negotiation to avoid entering L1 state. */ + gl9763e_set_low_power_negotiation(slot, false); + return 0; cleanup: @@ -1340,31 +1369,6 @@ static void gli_set_gl9763e(struct sdhci_pci_slot *slot) } #ifdef CONFIG_PM -static void gl9763e_set_low_power_negotiation(struct sdhci_pci_slot *slot, bool enable) -{ - struct pci_dev *pdev = slot->chip->pdev; - u32 value; - - pci_read_config_dword(pdev, PCIE_GLI_9763E_VHS, &value); - value &= ~GLI_9763E_VHS_REV; - value |= FIELD_PREP(GLI_9763E_VHS_REV, GLI_9763E_VHS_REV_W); - pci_write_config_dword(pdev, PCIE_GLI_9763E_VHS, value); - - pci_read_config_dword(pdev, PCIE_GLI_9763E_CFG, &value); - - if (enable) - value &= ~GLI_9763E_CFG_LPSN_DIS; - else - value |= GLI_9763E_CFG_LPSN_DIS; - - pci_write_config_dword(pdev, PCIE_GLI_9763E_CFG, value); - - pci_read_config_dword(pdev, PCIE_GLI_9763E_VHS, &value); - value &= ~GLI_9763E_VHS_REV; - value |= FIELD_PREP(GLI_9763E_VHS_REV, GLI_9763E_VHS_REV_R); - pci_write_config_dword(pdev, PCIE_GLI_9763E_VHS, value); -} - static int gl9763e_runtime_suspend(struct sdhci_pci_chip *chip) { struct sdhci_pci_slot *slot = chip->slots[0]; diff --git a/drivers/mmc/host/sdhci-sprd.c b/drivers/mmc/host/sdhci-sprd.c index 6b84ba27e6ab..bed57a1c64b5 100644 --- a/drivers/mmc/host/sdhci-sprd.c +++ b/drivers/mmc/host/sdhci-sprd.c @@ -239,15 +239,19 @@ static inline void _sdhci_sprd_set_clock(struct sdhci_host *host, div = ((div & 0x300) >> 2) | ((div & 0xFF) << 8); sdhci_enable_clk(host, div); + val = sdhci_readl(host, SDHCI_SPRD_REG_32_BUSY_POSI); + mask = SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN | SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN; /* Enable CLK_AUTO when the clock is greater than 400K. */ if (clk > 400000) { - val = sdhci_readl(host, SDHCI_SPRD_REG_32_BUSY_POSI); - mask = SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN | - SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN; if (mask != (val & mask)) { val |= mask; sdhci_writel(host, val, SDHCI_SPRD_REG_32_BUSY_POSI); } + } else { + if (val & mask) { + val &= ~mask; + sdhci_writel(host, val, SDHCI_SPRD_REG_32_BUSY_POSI); + } } } @@ -416,12 +420,33 @@ static void sdhci_sprd_request_done(struct sdhci_host *host, mmc_request_done(host->mmc, mrq); } +static void sdhci_sprd_set_power(struct sdhci_host *host, unsigned char mode, + unsigned short vdd) +{ + struct mmc_host *mmc = host->mmc; + + switch (mode) { + case MMC_POWER_OFF: + mmc_regulator_set_ocr(host->mmc, mmc->supply.vmmc, 0); + + mmc_regulator_disable_vqmmc(mmc); + break; + case MMC_POWER_ON: + mmc_regulator_enable_vqmmc(mmc); + break; + case MMC_POWER_UP: + mmc_regulator_set_ocr(host->mmc, mmc->supply.vmmc, vdd); + break; + } +} + static struct sdhci_ops sdhci_sprd_ops = { .read_l = sdhci_sprd_readl, .write_l = sdhci_sprd_writel, .write_w = sdhci_sprd_writew, .write_b = sdhci_sprd_writeb, .set_clock = sdhci_sprd_set_clock, + .set_power = sdhci_sprd_set_power, .get_max_clock = sdhci_sprd_get_max_clock, .get_min_clock = sdhci_sprd_get_min_clock, .set_bus_width = sdhci_set_bus_width, @@ -823,6 +848,10 @@ static int sdhci_sprd_probe(struct platform_device *pdev) host->caps1 &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_DDR50); + ret = mmc_regulator_get_supply(host->mmc); + if (ret) + goto pm_runtime_disable; + ret = sdhci_setup_host(host); if (ret) goto pm_runtime_disable; |