diff options
Diffstat (limited to 'arch/arm/boot/dts')
33 files changed, 2598 insertions, 251 deletions
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index f37cf9fa5fa0..fb5b07737ca7 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1,21 +1,37 @@ ifeq ($(CONFIG_OF),y) -dtb-$(CONFIG_ARCH_AT91) += aks-cdu.dtb \ - at91sam9263ek.dtb \ - at91sam9g20ek_2mmc.dtb \ - at91sam9g20ek.dtb \ - at91sam9g25ek.dtb \ - at91sam9m10g45ek.dtb \ - at91sam9n12ek.dtb \ - ethernut5.dtb \ - evk-pro3.dtb \ - kizbox.dtb \ - tny_a9260.dtb \ - tny_a9263.dtb \ - tny_a9g20.dtb \ - usb_a9260.dtb \ - usb_a9263.dtb \ - usb_a9g20.dtb +# Keep at91 dtb files sorted alphabetically for each SoC +# rm9200 +dtb-$(CONFIG_ARCH_AT91) += at91rm9200ek.dtb +# sam9260 +dtb-$(CONFIG_ARCH_AT91) += animeo_ip.dtb +dtb-$(CONFIG_ARCH_AT91) += aks-cdu.dtb +dtb-$(CONFIG_ARCH_AT91) += ethernut5.dtb +dtb-$(CONFIG_ARCH_AT91) += evk-pro3.dtb +dtb-$(CONFIG_ARCH_AT91) += tny_a9260.dtb +dtb-$(CONFIG_ARCH_AT91) += usb_a9260.dtb +# sam9263 +dtb-$(CONFIG_ARCH_AT91) += at91sam9263ek.dtb +dtb-$(CONFIG_ARCH_AT91) += tny_a9263.dtb +dtb-$(CONFIG_ARCH_AT91) += usb_a9263.dtb +# sam9g20 +dtb-$(CONFIG_ARCH_AT91) += at91sam9g20ek.dtb +dtb-$(CONFIG_ARCH_AT91) += at91sam9g20ek_2mmc.dtb +dtb-$(CONFIG_ARCH_AT91) += kizbox.dtb +dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb +dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb +# sam9g45 +dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb +dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb +# sam9n12 +dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb +# sam9x5 +dtb-$(CONFIG_ARCH_AT91) += at91sam9g15ek.dtb +dtb-$(CONFIG_ARCH_AT91) += at91sam9g25ek.dtb +dtb-$(CONFIG_ARCH_AT91) += at91sam9g35ek.dtb +dtb-$(CONFIG_ARCH_AT91) += at91sam9x25ek.dtb +dtb-$(CONFIG_ARCH_AT91) += at91sam9x35ek.dtb + dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \ dove-cubox.dtb \ diff --git a/arch/arm/boot/dts/animeo_ip.dts b/arch/arm/boot/dts/animeo_ip.dts new file mode 100644 index 000000000000..74d92cd29d87 --- /dev/null +++ b/arch/arm/boot/dts/animeo_ip.dts @@ -0,0 +1,178 @@ +/* + * animeo_ip.dts - Device Tree file for Somfy Animeo IP Boards + * + * Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2 only. + */ + +/dts-v1/; +/include/ "at91sam9260.dtsi" + +/ { + model = "Somfy Animeo IP"; + compatible = "somfy,animeo-ip", "atmel,at91sam9260", "atmel,at91sam9"; + + aliases { + serial0 = &usart1; + serial1 = &usart2; + serial2 = &usart0; + serial3 = &dbgu; + serial4 = &usart3; + serial5 = &uart0; + serial6 = &uart1; + }; + + chosen { + linux,stdout-path = &usart2; + }; + + memory { + reg = <0x20000000 0x4000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <18432000>; + }; + }; + + ahb { + apb { + usart0: serial@fffb0000 { + pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts>; + linux,rs485-enabled-at-boot-time; + status = "okay"; + }; + + usart1: serial@fffb4000 { + pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts>; + linux,rs485-enabled-at-boot-time; + status = "okay"; + }; + + usart2: serial@fffb8000 { + pinctrl-0 = <&pinctrl_usart2>; + status = "okay"; + }; + + macb0: ethernet@fffc4000 { + pinctrl-0 = <&pinctrl_macb_rmii &pinctrl_macb_rmii_mii>; + phy-mode = "mii"; + status = "okay"; + }; + + mmc0: mmc@fffa8000 { + pinctrl-0 = <&pinctrl_mmc0_clk + &pinctrl_mmc0_slot1_cmd_dat0 + &pinctrl_mmc0_slot1_dat1_3>; + status = "okay"; + + slot@1 { + reg = <1>; + bus-width = <4>; + }; + }; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x8000>; + }; + + barebox@8000 { + label = "barebox"; + reg = <0x8000 0x40000>; + }; + + bareboxenv@48000 { + label = "bareboxenv"; + reg = <0x48000 0x8000>; + }; + + user_block@0x50000 { + label = "user_block"; + reg = <0x50000 0xb0000>; + }; + + kernel@100000 { + label = "kernel"; + reg = <0x100000 0x1b0000>; + }; + + root@2b0000 { + label = "root"; + reg = <0x2b0000 0x1D50000>; + }; + }; + + usb0: ohci@00500000 { + num-ports = <2>; + atmel,vbus-gpio = <&pioB 15 1>; + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + + power_green { + label = "power_green"; + gpios = <&pioC 17 0>; + linux,default-trigger = "heartbeat"; + }; + + power_red { + label = "power_red"; + gpios = <&pioA 2 0>; + }; + + tx_green { + label = "tx_green"; + gpios = <&pioC 19 0>; + }; + + tx_red { + label = "tx_red"; + gpios = <&pioC 18 0>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + keyswitch_in { + label = "keyswitch_in"; + gpios = <&pioB 1 0>; + linux,code = <28>; + gpio-key,wakeup; + }; + + error_in { + label = "error_in"; + gpios = <&pioB 2 0>; + linux,code = <29>; + gpio-key,wakeup; + }; + + btn { + label = "btn"; + gpios = <&pioC 23 0>; + linux,code = <31>; + gpio-key,wakeup; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi new file mode 100644 index 000000000000..e154f242c680 --- /dev/null +++ b/arch/arm/boot/dts/at91rm9200.dtsi @@ -0,0 +1,349 @@ +/* + * at91rm9200.dtsi - Device Tree Include file for AT91RM9200 family SoC + * + * Copyright (C) 2011 Atmel, + * 2011 Nicolas Ferre <nicolas.ferre@atmel.com>, + * 2012 Joachim Eastwood <manabian@gmail.com> + * + * Based on at91sam9260.dtsi + * + * Licensed under GPLv2 or later. + */ + +/include/ "skeleton.dtsi" + +/ { + model = "Atmel AT91RM9200 family SoC"; + compatible = "atmel,at91rm9200"; + interrupt-parent = <&aic>; + + aliases { + serial0 = &dbgu; + serial1 = &usart0; + serial2 = &usart1; + serial3 = &usart2; + serial4 = &usart3; + gpio0 = &pioA; + gpio1 = &pioB; + gpio2 = &pioC; + gpio3 = &pioD; + tcb0 = &tcb0; + tcb1 = &tcb1; + }; + cpus { + cpu@0 { + compatible = "arm,arm920t"; + }; + }; + + memory { + reg = <0x20000000 0x04000000>; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + aic: interrupt-controller@fffff000 { + #interrupt-cells = <3>; + compatible = "atmel,at91rm9200-aic"; + interrupt-controller; + reg = <0xfffff000 0x200>; + atmel,external-irqs = <25 26 27 28 29 30 31>; + }; + + ramc0: ramc@ffffff00 { + compatible = "atmel,at91rm9200-sdramc"; + reg = <0xffffff00 0x100>; + }; + + pmc: pmc@fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + }; + + st: timer@fffffd00 { + compatible = "atmel,at91rm9200-st"; + reg = <0xfffffd00 0x100>; + interrupts = <1 4 7>; + }; + + tcb0: timer@fffa0000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfffa0000 0x100>; + interrupts = <17 4 0 18 4 0 19 4 0>; + }; + + tcb1: timer@fffa4000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfffa4000 0x100>; + interrupts = <20 4 0 21 4 0 22 4 0>; + }; + + pinctrl@fffff400 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; + ranges = <0xfffff400 0xfffff400 0x800>; + + atmel,mux-mask = < + /* A B */ + 0xffffffff 0xffffffff /* pioA */ + 0xffffffff 0x083fffff /* pioB */ + 0xffff3fff 0x00000000 /* pioC */ + 0x03ff87ff 0x0fffff80 /* pioD */ + >; + + /* shared pinctrl settings */ + dbgu { + pinctrl_dbgu: dbgu-0 { + atmel,pins = + <0 30 0x1 0x0 /* PA30 periph A */ + 0 31 0x1 0x1>; /* PA31 periph with pullup */ + }; + }; + + uart0 { + pinctrl_uart0: uart0-0 { + atmel,pins = + <0 17 0x1 0x0 /* PA17 periph A */ + 0 18 0x1 0x0>; /* PA18 periph A */ + }; + + pinctrl_uart0_rts: uart0_rts-0 { + atmel,pins = + <0 20 0x1 0x0>; /* PA20 periph A */ + }; + + pinctrl_uart0_cts: uart0_cts-0 { + atmel,pins = + <0 21 0x1 0x0>; /* PA21 periph A */ + }; + }; + + uart1 { + pinctrl_uart1: uart1-0 { + atmel,pins = + <1 20 0x1 0x1 /* PB20 periph A with pullup */ + 1 21 0x1 0x0>; /* PB21 periph A */ + }; + + pinctrl_uart1_rts: uart1_rts-0 { + atmel,pins = + <1 24 0x1 0x0>; /* PB24 periph A */ + }; + + pinctrl_uart1_cts: uart1_cts-0 { + atmel,pins = + <1 26 0x1 0x0>; /* PB26 periph A */ + }; + + pinctrl_uart1_dtr_dsr: uart1_dtr_dsr-0 { + atmel,pins = + <1 19 0x1 0x0 /* PB19 periph A */ + 1 25 0x1 0x0>; /* PB25 periph A */ + }; + + pinctrl_uart1_dcd: uart1_dcd-0 { + atmel,pins = + <1 23 0x1 0x0>; /* PB23 periph A */ + }; + + pinctrl_uart1_ri: uart1_ri-0 { + atmel,pins = + <1 18 0x1 0x0>; /* PB18 periph A */ + }; + }; + + uart2 { + pinctrl_uart2: uart2-0 { + atmel,pins = + <0 22 0x1 0x0 /* PA22 periph A */ + 0 23 0x1 0x1>; /* PA23 periph A with pullup */ + }; + + pinctrl_uart2_rts: uart2_rts-0 { + atmel,pins = + <0 30 0x2 0x0>; /* PA30 periph B */ + }; + + pinctrl_uart2_cts: uart2_cts-0 { + atmel,pins = + <0 31 0x2 0x0>; /* PA31 periph B */ + }; + }; + + uart3 { + pinctrl_uart3: uart3-0 { + atmel,pins = + <0 5 0x2 0x1 /* PA5 periph B with pullup */ + 0 6 0x2 0x0>; /* PA6 periph B */ + }; + + pinctrl_uart3_rts: uart3_rts-0 { + atmel,pins = + <1 0 0x2 0x0>; /* PB0 periph B */ + }; + + pinctrl_uart3_cts: uart3_cts-0 { + atmel,pins = + <1 1 0x2 0x0>; /* PB1 periph B */ + }; + }; + + nand { + pinctrl_nand: nand-0 { + atmel,pins = + <2 2 0x0 0x1 /* PC2 gpio RDY pin pull_up */ + 1 1 0x0 0x1>; /* PB1 gpio CD pin pull_up */ + }; + }; + + pioA: gpio@fffff400 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff400 0x200>; + interrupts = <2 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioB: gpio@fffff600 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff600 0x200>; + interrupts = <3 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioC: gpio@fffff800 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff800 0x200>; + interrupts = <4 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioD: gpio@fffffa00 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffffa00 0x200>; + interrupts = <5 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + dbgu: serial@fffff200 { + compatible = "atmel,at91rm9200-usart"; + reg = <0xfffff200 0x200>; + interrupts = <1 4 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dbgu>; + status = "disabled"; + }; + + usart0: serial@fffc0000 { + compatible = "atmel,at91rm9200-usart"; + reg = <0xfffc0000 0x200>; + interrupts = <6 4 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0>; + status = "disabled"; + }; + + usart1: serial@fffc4000 { + compatible = "atmel,at91rm9200-usart"; + reg = <0xfffc4000 0x200>; + interrupts = <7 4 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "disabled"; + }; + + usart2: serial@fffc8000 { + compatible = "atmel,at91rm9200-usart"; + reg = <0xfffc8000 0x200>; + interrupts = <8 4 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "disabled"; + }; + + usart3: serial@fffcc000 { + compatible = "atmel,at91rm9200-usart"; + reg = <0xfffcc000 0x200>; + interrupts = <23 4 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "disabled"; + }; + + usb1: gadget@fffb0000 { + compatible = "atmel,at91rm9200-udc"; + reg = <0xfffb0000 0x4000>; + interrupts = <11 4 2>; + status = "disabled"; + }; + }; + + nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000>; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nand>; + nand-ecc-mode = "soft"; + gpios = <&pioC 2 0 + 0 + &pioB 1 0 + >; + status = "disabled"; + }; + + usb0: ohci@00300000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00300000 0x100000>; + interrupts = <23 4 2>; + status = "disabled"; + }; + }; + + i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioA 23 0 /* sda */ + &pioA 24 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; +}; diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/at91rm9200ek.dts new file mode 100644 index 000000000000..8aa48931e0a2 --- /dev/null +++ b/arch/arm/boot/dts/at91rm9200ek.dts @@ -0,0 +1,79 @@ +/* + * at91rm9200ek.dts - Device Tree file for Atmel AT91RM9200 evaluation kit + * + * Copyright (C) 2012 Joachim Eastwood <manabian@gmail.com> + * + * Licensed under GPLv2 only + */ +/dts-v1/; +/include/ "at91rm9200.dtsi" + +/ { + model = "Atmel AT91RM9200 evaluation kit"; + compatible = "atmel,at91rm9200ek", "atmel,at91rm9200"; + + memory { + reg = <0x20000000 0x4000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <18432000>; + }; + }; + + ahb { + apb { + dbgu: serial@fffff200 { + status = "okay"; + }; + + usart1: serial@fffc4000 { + pinctrl-0 = + <&pinctrl_uart1 + &pinctrl_uart1_rts + &pinctrl_uart1_cts + &pinctrl_uart1_dtr_dsr + &pinctrl_uart1_dcd + &pinctrl_uart1_ri>; + status = "okay"; + }; + + usb1: gadget@fffb0000 { + atmel,vbus-gpio = <&pioD 4 0>; + status = "okay"; + }; + }; + + usb0: ohci@00300000 { + num-ports = <2>; + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + + ds2 { + label = "green"; + gpios = <&pioB 0 0x1>; + linux,default-trigger = "mmc0"; + }; + + ds4 { + label = "yellow"; + gpios = <&pioB 1 0x1>; + linux,default-trigger = "heartbeat"; + }; + + ds6 { + label = "red"; + gpios = <&pioB 2 0x1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi index d410581a5a85..b1d3fab60e0a 100644 --- a/arch/arm/boot/dts/at91sam9260.dtsi +++ b/arch/arm/boot/dts/at91sam9260.dtsi @@ -21,8 +21,8 @@ serial2 = &usart1; serial3 = &usart2; serial4 = &usart3; - serial5 = &usart4; - serial6 = &usart5; + serial5 = &uart0; + serial6 = &uart1; gpio0 = &pioA; gpio1 = &pioB; gpio2 = &pioC; @@ -98,40 +98,250 @@ interrupts = <26 4 0 27 4 0 28 4 0>; }; - pioA: gpio@fffff400 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff400 0x100>; - interrupts = <2 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + pinctrl@fffff400 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; + ranges = <0xfffff400 0xfffff400 0x600>; + + atmel,mux-mask = < + /* A B */ + 0xffffffff 0xffc00c3b /* pioA */ + 0xffffffff 0x7fff3ccf /* pioB */ + 0xffffffff 0x007fffff /* pioC */ + >; + + /* shared pinctrl settings */ + dbgu { + pinctrl_dbgu: dbgu-0 { + atmel,pins = + <1 14 0x1 0x0 /* PB14 periph A */ + 1 15 0x1 0x1>; /* PB15 periph with pullup */ + }; + }; - pioB: gpio@fffff600 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff600 0x100>; - interrupts = <3 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + usart0 { + pinctrl_usart0: usart0-0 { + atmel,pins = + <1 4 0x1 0x0 /* PB4 periph A */ + 1 5 0x1 0x0>; /* PB5 periph A */ + }; + + pinctrl_usart0_rts: usart0_rts-0 { + atmel,pins = + <1 26 0x1 0x0>; /* PB26 periph A */ + }; + + pinctrl_usart0_cts: usart0_cts-0 { + atmel,pins = + <1 27 0x1 0x0>; /* PB27 periph A */ + }; + + pinctrl_usart0_dtr_dsr: usart0_dtr_dsr-0 { + atmel,pins = + <1 24 0x1 0x0 /* PB24 periph A */ + 1 22 0x1 0x0>; /* PB22 periph A */ + }; + + pinctrl_usart0_dcd: usart0_dcd-0 { + atmel,pins = + <1 23 0x1 0x0>; /* PB23 periph A */ + }; + + pinctrl_usart0_ri: usart0_ri-0 { + atmel,pins = + <1 25 0x1 0x0>; /* PB25 periph A */ + }; + }; - pioC: gpio@fffff800 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff800 0x100>; - interrupts = <4 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; + usart1 { + pinctrl_usart1: usart1-0 { + atmel,pins = + <2 6 0x1 0x1 /* PB6 periph A with pullup */ + 2 7 0x1 0x0>; /* PB7 periph A */ + }; + + pinctrl_usart1_rts: usart1_rts-0 { + atmel,pins = + <1 28 0x1 0x0>; /* PB28 periph A */ + }; + + pinctrl_usart1_cts: usart1_cts-0 { + atmel,pins = + <1 29 0x1 0x0>; /* PB29 periph A */ + }; + }; + + usart2 { + pinctrl_usart2: usart2-0 { + atmel,pins = + <1 8 0x1 0x1 /* PB8 periph A with pullup */ + 1 9 0x1 0x0>; /* PB9 periph A */ + }; + + pinctrl_usart2_rts: usart2_rts-0 { + atmel,pins = + <0 4 0x1 0x0>; /* PA4 periph A */ + }; + + pinctrl_usart2_cts: usart2_cts-0 { + atmel,pins = + <0 5 0x1 0x0>; /* PA5 periph A */ + }; + }; + + usart3 { + pinctrl_usart3: usart3-0 { + atmel,pins = + <2 10 0x1 0x1 /* PB10 periph A with pullup */ + 2 11 0x1 0x0>; /* PB11 periph A */ + }; + + pinctrl_usart3_rts: usart3_rts-0 { + atmel,pins = + <3 8 0x2 0x0>; /* PB8 periph B */ + }; + + pinctrl_usart3_cts: usart3_cts-0 { + atmel,pins = + <3 10 0x2 0x0>; /* PB10 periph B */ + }; + }; + + uart0 { + pinctrl_uart0: uart0-0 { + atmel,pins = + <0 31 0x2 0x1 /* PA31 periph B with pullup */ + 0 30 0x2 0x0>; /* PA30 periph B */ + }; + }; + + uart1 { + pinctrl_uart1: uart1-0 { + atmel,pins = + <2 12 0x1 0x1 /* PB12 periph A with pullup */ + 2 13 0x1 0x0>; /* PB13 periph A */ + }; + }; + + nand { + pinctrl_nand: nand-0 { + atmel,pins = + <2 13 0x0 0x1 /* PC13 gpio RDY pin pull_up */ + 2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */ + }; + }; + + macb { + pinctrl_macb_rmii: macb_rmii-0 { + atmel,pins = + <0 12 0x1 0x0 /* PA12 periph A */ + 0 13 0x1 0x0 /* PA13 periph A */ + 0 14 0x1 0x0 /* PA14 periph A */ + 0 15 0x1 0x0 /* PA15 periph A */ + 0 16 0x1 0x0 /* PA16 periph A */ + 0 17 0x1 0x0 /* PA17 periph A */ + 0 18 0x1 0x0 /* PA18 periph A */ + 0 19 0x1 0x0 /* PA19 periph A */ + 0 20 0x1 0x0 /* PA20 periph A */ + 0 21 0x1 0x0>; /* PA21 periph A */ + }; + + pinctrl_macb_rmii_mii: macb_rmii_mii-0 { + atmel,pins = + <0 22 0x2 0x0 /* PA22 periph B */ + 0 23 0x2 0x0 /* PA23 periph B */ + 0 24 0x2 0x0 /* PA24 periph B */ + 0 25 0x2 0x0 /* PA25 periph B */ + 0 26 0x2 0x0 /* PA26 periph B */ + 0 27 0x2 0x0 /* PA27 periph B */ + 0 28 0x2 0x0 /* PA28 periph B */ + 0 29 0x2 0x0>; /* PA29 periph B */ + }; + + pinctrl_macb_rmii_mii_alt: macb_rmii_mii-1 { + atmel,pins = + <0 10 0x2 0x0 /* PA10 periph B */ + 0 11 0x2 0x0 /* PA11 periph B */ + 0 24 0x2 0x0 /* PA24 periph B */ + 0 25 0x2 0x0 /* PA25 periph B */ + 0 26 0x2 0x0 /* PA26 periph B */ + 0 27 0x2 0x0 /* PA27 periph B */ + 0 28 0x2 0x0 /* PA28 periph B */ + 0 29 0x2 0x0>; /* PA29 periph B */ + }; + }; + + mmc0 { + pinctrl_mmc0_clk: mmc0_clk-0 { + atmel,pins = + <0 8 0x1 0x0>; /* PA8 periph A */ + }; + + pinctrl_mmc0_slot0_cmd_dat0: mmc0_slot0_cmd_dat0-0 { + atmel,pins = + <0 7 0x1 0x1 /* PA7 periph A with pullup */ + 0 6 0x1 0x1>; /* PA6 periph A with pullup */ + }; + + pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 { + atmel,pins = + <0 9 0x1 0x1 /* PA9 periph A with pullup */ + 0 10 0x1 0x1 /* PA10 periph A with pullup */ + 0 11 0x1 0x1>; /* PA11 periph A with pullup */ + }; + + pinctrl_mmc0_slot1_cmd_dat0: mmc0_slot1_cmd_dat0-0 { + atmel,pins = + <0 1 0x2 0x1 /* PA1 periph B with pullup */ + 0 0 0x2 0x1>; /* PA0 periph B with pullup */ + }; + + pinctrl_mmc0_slot1_dat1_3: mmc0_slot1_dat1_3-0 { + atmel,pins = + <0 5 0x2 0x1 /* PA5 periph B with pullup */ + 0 4 0x2 0x1 /* PA4 periph B with pullup */ + 0 3 0x2 0x1>; /* PA3 periph B with pullup */ + }; + }; + + pioA: gpio@fffff400 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff400 0x200>; + interrupts = <2 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioB: gpio@fffff600 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff600 0x200>; + interrupts = <3 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioC: gpio@fffff800 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff800 0x200>; + interrupts = <4 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; }; dbgu: serial@fffff200 { compatible = "atmel,at91sam9260-usart"; reg = <0xfffff200 0x200>; interrupts = <1 4 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dbgu>; status = "disabled"; }; @@ -141,6 +351,8 @@ interrupts = <6 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart0>; status = "disabled"; }; @@ -150,6 +362,8 @@ interrupts = <7 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart1>; status = "disabled"; }; @@ -159,6 +373,8 @@ interrupts = <8 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart2>; status = "disabled"; }; @@ -168,24 +384,30 @@ interrupts = <23 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart3>; status = "disabled"; }; - usart4: serial@fffd4000 { + uart0: serial@fffd4000 { compatible = "atmel,at91sam9260-usart"; reg = <0xfffd4000 0x200>; interrupts = <24 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0>; status = "disabled"; }; - usart5: serial@fffd8000 { + uart1: serial@fffd8000 { compatible = "atmel,at91sam9260-usart"; reg = <0xfffd8000 0x200>; interrupts = <25 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; status = "disabled"; }; @@ -193,6 +415,8 @@ compatible = "cdns,at32ap7000-macb", "cdns,macb"; reg = <0xfffc4000 0x100>; interrupts = <21 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_macb_rmii>; status = "disabled"; }; @@ -212,6 +436,15 @@ status = "disabled"; }; + mmc0: mmc@fffa8000 { + compatible = "atmel,hsmci"; + reg = <0xfffa8000 0x600>; + interrupts = <9 4 0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + adc0: adc@fffe0000 { compatible = "atmel,at91sam9260-adc"; reg = <0xfffe0000 0x100>; @@ -257,6 +490,8 @@ >; atmel,nand-addr-offset = <21>; atmel,nand-cmd-offset = <22>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nand>; gpios = <&pioC 13 0 &pioC 14 0 0 diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi index 3e6e5c1abbf3..66106eecf1ed 100644 --- a/arch/arm/boot/dts/at91sam9263.dtsi +++ b/arch/arm/boot/dts/at91sam9263.dtsi @@ -89,60 +89,243 @@ reg = <0xfffffd10 0x10>; }; - pioA: gpio@fffff200 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff200 0x100>; - interrupts = <2 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + pinctrl@fffff200 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; + ranges = <0xfffff200 0xfffff200 0xa00>; - pioB: gpio@fffff400 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff400 0x100>; - interrupts = <3 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + atmel,mux-mask = < + /* A B */ + 0xfffffffb 0xffffe07f /* pioA */ + 0x0007ffff 0x39072fff /* pioB */ + 0xffffffff 0x3ffffff8 /* pioC */ + 0xfffffbff 0xffffffff /* pioD */ + 0xffe00fff 0xfbfcff00 /* pioE */ + >; - pioC: gpio@fffff600 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff600 0x100>; - interrupts = <4 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + /* shared pinctrl settings */ + dbgu { + pinctrl_dbgu: dbgu-0 { + atmel,pins = + <2 30 0x1 0x0 /* PC30 periph A */ + 2 31 0x1 0x1>; /* PC31 periph with pullup */ + }; + }; - pioD: gpio@fffff800 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff800 0x100>; - interrupts = <4 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + usart0 { + pinctrl_usart0: usart0-0 { + atmel,pins = + <0 26 0x1 0x1 /* PA26 periph A with pullup */ + 0 27 0x1 0x0>; /* PA27 periph A */ + }; - pioE: gpio@fffffa00 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffffa00 0x100>; - interrupts = <4 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; + pinctrl_usart0_rts: usart0_rts-0 { + atmel,pins = + <0 28 0x1 0x0>; /* PA28 periph A */ + }; + + pinctrl_usart0_cts: usart0_cts-0 { + atmel,pins = + <0 29 0x1 0x0>; /* PA29 periph A */ + }; + }; + + usart1 { + pinctrl_usart1: usart1-0 { + atmel,pins = + <3 0 0x1 0x1 /* PD0 periph A with pullup */ + 3 1 0x1 0x0>; /* PD1 periph A */ + }; + + pinctrl_usart1_rts: usart1_rts-0 { + atmel,pins = + <3 7 0x2 0x0>; /* PD7 periph B */ + }; + + pinctrl_usart1_cts: usart1_cts-0 { + atmel,pins = + <3 8 0x2 0x0>; /* PD8 periph B */ + }; + }; + + usart2 { + pinctrl_usart2: usart2-0 { + atmel,pins = + <3 2 0x1 0x1 /* PD2 periph A with pullup */ + 3 3 0x1 0x0>; /* PD3 periph A */ + }; + + pinctrl_usart2_rts: usart2_rts-0 { + atmel,pins = + <3 5 0x2 0x0>; /* PD5 periph B */ + }; + + pinctrl_usart2_cts: usart2_cts-0 { + atmel,pins = + <4 6 0x2 0x0>; /* PD6 periph B */ + }; + }; + + nand { + pinctrl_nand: nand-0 { + atmel,pins = + <0 22 0x0 0x1 /* PA22 gpio RDY pin pull_up*/ + 3 15 0x0 0x1>; /* PD15 gpio enable pin pull_up */ + }; + }; + + macb { + pinctrl_macb_rmii: macb_rmii-0 { + atmel,pins = + <2 25 0x2 0x0 /* PC25 periph B */ + 4 21 0x1 0x0 /* PE21 periph A */ + 4 23 0x1 0x0 /* PE23 periph A */ + 4 24 0x1 0x0 /* PE24 periph A */ + 4 25 0x1 0x0 /* PE25 periph A */ + 4 26 0x1 0x0 /* PE26 periph A */ + 4 27 0x1 0x0 /* PE27 periph A */ + 4 28 0x1 0x0 /* PE28 periph A */ + 4 29 0x1 0x0 /* PE29 periph A */ + 4 30 0x1 0x0>; /* PE30 periph A */ + }; + + pinctrl_macb_rmii_mii: macb_rmii_mii-0 { + atmel,pins = + <2 20 0x2 0x0 /* PC20 periph B */ + 2 21 0x2 0x0 /* PC21 periph B */ + 2 22 0x2 0x0 /* PC22 periph B */ + 2 23 0x2 0x0 /* PC23 periph B */ + 2 24 0x2 0x0 /* PC24 periph B */ + 2 25 0x2 0x0 /* PC25 periph B */ + 2 27 0x2 0x0 /* PC27 periph B */ + 4 22 0x2 0x0>; /* PE22 periph B */ + }; + }; + + mmc0 { + pinctrl_mmc0_clk: mmc0_clk-0 { + atmel,pins = + <0 12 0x1 0x0>; /* PA12 periph A */ + }; + + pinctrl_mmc0_slot0_cmd_dat0: mmc0_slot0_cmd_dat0-0 { + atmel,pins = + <0 1 0x1 0x1 /* PA1 periph A with pullup */ + 0 0 0x1 0x1>; /* PA0 periph A with pullup */ + }; + + pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 { + atmel,pins = + <0 3 0x1 0x1 /* PA3 periph A with pullup */ + 0 4 0x1 0x1 /* PA4 periph A with pullup */ + 0 5 0x1 0x1>; /* PA5 periph A with pullup */ + }; + + pinctrl_mmc0_slot1_cmd_dat0: mmc0_slot1_cmd_dat0-0 { + atmel,pins = + <0 16 0x1 0x1 /* PA16 periph A with pullup */ + 0 17 0x1 0x1>; /* PA17 periph A with pullup */ + }; + + pinctrl_mmc0_slot1_dat1_3: mmc0_slot1_dat1_3-0 { + atmel,pins = + <0 18 0x1 0x1 /* PA18 periph A with pullup */ + 0 19 0x1 0x1 /* PA19 periph A with pullup */ + 0 20 0x1 0x1>; /* PA20 periph A with pullup */ + }; + }; + + mmc1 { + pinctrl_mmc1_clk: mmc1_clk-0 { + atmel,pins = + <0 6 0x1 0x0>; /* PA6 periph A */ + }; + + pinctrl_mmc1_slot0_cmd_dat0: mmc1_slot0_cmd_dat0-0 { + atmel,pins = + <0 7 0x1 0x1 /* PA7 periph A with pullup */ + 0 8 0x1 0x1>; /* PA8 periph A with pullup */ + }; + + pinctrl_mmc1_slot0_dat1_3: mmc1_slot0_dat1_3-0 { + atmel,pins = + <0 9 0x1 0x1 /* PA9 periph A with pullup */ + 0 10 0x1 0x1 /* PA10 periph A with pullup */ + 0 11 0x1 0x1>; /* PA11 periph A with pullup */ + }; + + pinctrl_mmc1_slot1_cmd_dat0: mmc1_slot1_cmd_dat0-0 { + atmel,pins = + <0 21 0x1 0x1 /* PA21 periph A with pullup */ + 0 22 0x1 0x1>; /* PA22 periph A with pullup */ + }; + + pinctrl_mmc1_slot1_dat1_3: mmc1_slot1_dat1_3-0 { + atmel,pins = + <0 23 0x1 0x1 /* PA23 periph A with pullup */ + 0 24 0x1 0x1 /* PA24 periph A with pullup */ + 0 25 0x1 0x1>; /* PA25 periph A with pullup */ + }; + }; + + pioA: gpio@fffff200 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff200 0x200>; + interrupts = <2 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioB: gpio@fffff400 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff400 0x200>; + interrupts = <3 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioC: gpio@fffff600 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff600 0x200>; + interrupts = <4 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioD: gpio@fffff800 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff800 0x200>; + interrupts = <4 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioE: gpio@fffffa00 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffffa00 0x200>; + interrupts = <4 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; }; dbgu: serial@ffffee00 { compatible = "atmel,at91sam9260-usart"; reg = <0xffffee00 0x200>; interrupts = <1 4 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dbgu>; status = "disabled"; }; @@ -152,6 +335,8 @@ interrupts = <7 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart0>; status = "disabled"; }; @@ -161,6 +346,8 @@ interrupts = <8 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart1>; status = "disabled"; }; @@ -170,6 +357,8 @@ interrupts = <9 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart2>; status = "disabled"; }; @@ -177,6 +366,8 @@ compatible = "cdns,at32ap7000-macb", "cdns,macb"; reg = <0xfffbc000 0x100>; interrupts = <21 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_macb_rmii>; status = "disabled"; }; @@ -195,6 +386,24 @@ #size-cells = <0>; status = "disabled"; }; + + mmc0: mmc@fff80000 { + compatible = "atmel,hsmci"; + reg = <0xfff80000 0x600>; + interrupts = <10 4 0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + mmc1: mmc@fff84000 { + compatible = "atmel,hsmci"; + reg = <0xfff84000 0x600>; + interrupts = <11 4 0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; nand0: nand@40000000 { @@ -206,6 +415,8 @@ >; atmel,nand-addr-offset = <21>; atmel,nand-cmd-offset = <22>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nand>; gpios = <&pioA 22 0 &pioD 15 0 0 diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts index f86ac4b609fc..1eb08728f527 100644 --- a/arch/arm/boot/dts/at91sam9263ek.dts +++ b/arch/arm/boot/dts/at91sam9263ek.dts @@ -38,6 +38,10 @@ }; usart0: serial@fff8c000 { + pinctrl-0 = < + &pinctrl_usart0 + &pinctrl_usart0_rts + &pinctrl_usart0_cts>; status = "okay"; }; @@ -50,6 +54,31 @@ atmel,vbus-gpio = <&pioA 25 0>; status = "okay"; }; + + mmc0: mmc@fff80000 { + pinctrl-0 = < + &pinctrl_board_mmc0 + &pinctrl_mmc0_clk + &pinctrl_mmc0_slot0_cmd_dat0 + &pinctrl_mmc0_slot0_dat1_3>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioE 18 0>; + wp-gpios = <&pioE 19 0>; + }; + }; + + pinctrl@fffff200 { + mmc0 { + pinctrl_board_mmc0: mmc0-board { + atmel,pins = + <5 18 0x0 0x5 /* PE18 gpio CD pin pull up and deglitch */ + 5 19 0x0 0x1>; /* PE19 gpio WP pin pull up */ + }; + }; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9g15.dtsi b/arch/arm/boot/dts/at91sam9g15.dtsi new file mode 100644 index 000000000000..fbe7a7089c2a --- /dev/null +++ b/arch/arm/boot/dts/at91sam9g15.dtsi @@ -0,0 +1,28 @@ +/* + * at91sam9g15.dtsi - Device Tree Include file for AT91SAM9G15 SoC + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ + +/include/ "at91sam9x5.dtsi" + +/ { + model = "Atmel AT91SAM9G15 SoC"; + compatible = "atmel, at91sam9g15, atmel,at91sam9x5"; + + ahb { + apb { + pinctrl@fffff400 { + atmel,mux-mask = < + /* A B C */ + 0xffffffff 0xffe0399f 0x00000000 /* pioA */ + 0x00040000 0x00047e3f 0x00000000 /* pioB */ + 0xfdffffff 0x00000000 0xb83fffff /* pioC */ + 0x003fffff 0x003f8000 0x00000000 /* pioD */ + >; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9g15ek.dts b/arch/arm/boot/dts/at91sam9g15ek.dts new file mode 100644 index 000000000000..86dd3f6d938f --- /dev/null +++ b/arch/arm/boot/dts/at91sam9g15ek.dts @@ -0,0 +1,16 @@ +/* + * at91sam9g15ek.dts - Device Tree file for AT91SAM9G15-EK board + * + * Copyright (C) 2012 Atmel, + * 2012 Nicolas Ferre <nicolas.ferre@atmel.com> + * + * Licensed under GPLv2 or later. + */ +/dts-v1/; +/include/ "at91sam9g15.dtsi" +/include/ "at91sam9x5ek.dtsi" + +/ { + model = "Atmel AT91SAM9G25-EK"; + compatible = "atmel,at91sam9g15ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9"; +}; diff --git a/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts b/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts index f1b2e148ac8c..66467b113126 100644 --- a/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts +++ b/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts @@ -12,6 +12,32 @@ model = "Atmel at91sam9g20ek 2 mmc"; compatible = "atmel,at91sam9g20ek_2mmc", "atmel,at91sam9g20", "atmel,at91sam9"; + ahb { + apb{ + mmc0: mmc@fffa8000 { + /* clk already mux wuth slot0 */ + pinctrl-0 = < + &pinctrl_board_mmc0_slot0 + &pinctrl_mmc0_slot0_cmd_dat0 + &pinctrl_mmc0_slot0_dat1_3>; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioC 2 0>; + }; + }; + + pinctrl@fffff400 { + mmc0_slot0 { + pinctrl_board_mmc0_slot0: mmc0_slot0-board { + atmel,pins = + <2 2 0x0 0x5>; /* PC2 gpio CD pin pull up and deglitch */ + }; + }; + }; + }; + }; + leds { compatible = "gpio-leds"; diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi index e6391a4e6649..32a500a0e481 100644 --- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi +++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi @@ -35,6 +35,13 @@ }; usart0: serial@fffb0000 { + pinctrl-0 = + <&pinctrl_usart0 + &pinctrl_usart0_rts + &pinctrl_usart0_cts + &pinctrl_usart0_dtr_dsr + &pinctrl_usart0_dcd + &pinctrl_usart0_ri>; status = "okay"; }; @@ -51,6 +58,29 @@ atmel,vbus-gpio = <&pioC 5 0>; status = "okay"; }; + + mmc0: mmc@fffa8000 { + pinctrl-0 = < + &pinctrl_board_mmc0_slot1 + &pinctrl_mmc0_clk + &pinctrl_mmc0_slot1_cmd_dat0 + &pinctrl_mmc0_slot1_dat1_3>; + status = "okay"; + slot@1 { + reg = <1>; + bus-width = <4>; + cd-gpios = <&pioC 9 0>; + }; + }; + + pinctrl@fffff400 { + mmc0_slot1 { + pinctrl_board_mmc0_slot1: mmc0_slot1-board { + atmel,pins = + <2 9 0x0 0x5>; /* PC9 gpio CD pin pull up and deglitch */ + }; + }; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9g25.dtsi b/arch/arm/boot/dts/at91sam9g25.dtsi new file mode 100644 index 000000000000..05a718fb83c4 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9g25.dtsi @@ -0,0 +1,28 @@ +/* + * at91sam9g25.dtsi - Device Tree Include file for AT91SAM9G25 SoC + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ + +/include/ "at91sam9x5.dtsi" + +/ { + model = "Atmel AT91SAM9G25 SoC"; + compatible = "atmel, at91sam9g25, atmel,at91sam9x5"; + + ahb { + apb { + pinctrl@fffff400 { + atmel,mux-mask = < + /* A B C */ + 0xffffffff 0xffe0399f 0xc000001c /* pioA */ + 0x0007ffff 0x8000fe3f 0x00000000 /* pioB */ + 0x80000000 0x07c0ffff 0xb83fffff /* pioC */ + 0x003fffff 0x003f8000 0x00000000 /* pioD */ + >; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9g25ek.dts b/arch/arm/boot/dts/at91sam9g25ek.dts index 877c08f06763..c5ab16fba059 100644 --- a/arch/arm/boot/dts/at91sam9g25ek.dts +++ b/arch/arm/boot/dts/at91sam9g25ek.dts @@ -7,55 +7,10 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9x5.dtsi" -/include/ "at91sam9x5cm.dtsi" +/include/ "at91sam9g25.dtsi" +/include/ "at91sam9x5ek.dtsi" / { model = "Atmel AT91SAM9G25-EK"; compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9"; - - chosen { - bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs"; - }; - - ahb { - apb { - dbgu: serial@fffff200 { - status = "okay"; - }; - - usart0: serial@f801c000 { - status = "okay"; - }; - - macb0: ethernet@f802c000 { - phy-mode = "rmii"; - status = "okay"; - }; - - i2c0: i2c@f8010000 { - status = "okay"; - }; - - i2c1: i2c@f8014000 { - status = "okay"; - }; - - i2c2: i2c@f8018000 { - status = "okay"; - }; - }; - - usb0: ohci@00600000 { - status = "okay"; - num-ports = <2>; - atmel,vbus-gpio = <&pioD 19 1 - &pioD 20 1 - >; - }; - - usb1: ehci@00700000 { - status = "okay"; - }; - }; }; diff --git a/arch/arm/boot/dts/at91sam9g35.dtsi b/arch/arm/boot/dts/at91sam9g35.dtsi new file mode 100644 index 000000000000..f9d14a722794 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9g35.dtsi @@ -0,0 +1,28 @@ +/* + * at91sam9g35.dtsi - Device Tree Include file for AT91SAM9G35 SoC + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ + +/include/ "at91sam9x5.dtsi" + +/ { + model = "Atmel AT91SAM9G35 SoC"; + compatible = "atmel, at91sam9g35, atmel,at91sam9x5"; + + ahb { + apb { + pinctrl@fffff400 { + atmel,mux-mask = < + /* A B C */ + 0xffffffff 0xffe0399f 0xc000000c /* pioA */ + 0x000406ff 0x00047e3f 0x00000000 /* pioB */ + 0xfdffffff 0x00000000 0xb83fffff /* pioC */ + 0x003fffff 0x003f8000 0x00000000 /* pioD */ + >; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9g35ek.dts b/arch/arm/boot/dts/at91sam9g35ek.dts new file mode 100644 index 000000000000..95944bdd798d --- /dev/null +++ b/arch/arm/boot/dts/at91sam9g35ek.dts @@ -0,0 +1,16 @@ +/* + * at91sam9g35ek.dts - Device Tree file for AT91SAM9G35-EK board + * + * Copyright (C) 2012 Atmel, + * 2012 Nicolas Ferre <nicolas.ferre@atmel.com> + * + * Licensed under GPLv2 or later. + */ +/dts-v1/; +/include/ "at91sam9g35.dtsi" +/include/ "at91sam9x5ek.dtsi" + +/ { + model = "Atmel AT91SAM9G35-EK"; + compatible = "atmel,at91sam9g35ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9"; +}; diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi index 3add030d61f8..0741caeeced1 100644 --- a/arch/arm/boot/dts/at91sam9g45.dtsi +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -108,60 +108,243 @@ interrupts = <21 4 0>; }; - pioA: gpio@fffff200 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff200 0x100>; - interrupts = <2 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + pinctrl@fffff200 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; + ranges = <0xfffff200 0xfffff200 0xa00>; + + atmel,mux-mask = < + /* A B */ + 0xffffffff 0xffc003ff /* pioA */ + 0xffffffff 0x800f8f00 /* pioB */ + 0xffffffff 0x00000e00 /* pioC */ + 0xffffffff 0xff0c1381 /* pioD */ + 0xffffffff 0x81ffff81 /* pioE */ + >; + + /* shared pinctrl settings */ + dbgu { + pinctrl_dbgu: dbgu-0 { + atmel,pins = + <1 12 0x1 0x0 /* PB12 periph A */ + 1 13 0x1 0x0>; /* PB13 periph A */ + }; + }; - pioB: gpio@fffff400 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff400 0x100>; - interrupts = <3 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + usart0 { + pinctrl_usart0: usart0-0 { + atmel,pins = + <1 19 0x1 0x1 /* PB19 periph A with pullup */ + 1 18 0x1 0x0>; /* PB18 periph A */ + }; + + pinctrl_usart0_rts: usart0_rts-0 { + atmel,pins = + <1 17 0x2 0x0>; /* PB17 periph B */ + }; + + pinctrl_usart0_cts: usart0_cts-0 { + atmel,pins = + <1 15 0x2 0x0>; /* PB15 periph B */ + }; + }; - pioC: gpio@fffff600 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff600 0x100>; - interrupts = <4 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + uart1 { + pinctrl_usart1: usart1-0 { + atmel,pins = + <1 4 0x1 0x1 /* PB4 periph A with pullup */ + 1 5 0x1 0x0>; /* PB5 periph A */ + }; + + pinctrl_usart1_rts: usart1_rts-0 { + atmel,pins = + <3 16 0x1 0x0>; /* PD16 periph A */ + }; + + pinctrl_usart1_cts: usart1_cts-0 { + atmel,pins = + <3 17 0x1 0x0>; /* PD17 periph A */ + }; + }; - pioD: gpio@fffff800 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff800 0x100>; - interrupts = <5 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + usart2 { + pinctrl_usart2: usart2-0 { + atmel,pins = + <1 6 0x1 0x1 /* PB6 periph A with pullup */ + 1 7 0x1 0x0>; /* PB7 periph A */ + }; + + pinctrl_usart2_rts: usart2_rts-0 { + atmel,pins = + <2 9 0x2 0x0>; /* PC9 periph B */ + }; + + pinctrl_usart2_cts: usart2_cts-0 { + atmel,pins = + <2 11 0x2 0x0>; /* PC11 periph B */ + }; + }; - pioE: gpio@fffffa00 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffffa00 0x100>; - interrupts = <5 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; + usart3 { + pinctrl_usart3: usart3-0 { + atmel,pins = + <1 8 0x1 0x1 /* PB9 periph A with pullup */ + 1 9 0x1 0x0>; /* PB8 periph A */ + }; + + pinctrl_usart3_rts: usart3_rts-0 { + atmel,pins = + <0 23 0x2 0x0>; /* PA23 periph B */ + }; + + pinctrl_usart3_cts: usart3_cts-0 { + atmel,pins = + <0 24 0x2 0x0>; /* PA24 periph B */ + }; + }; + + nand { + pinctrl_nand: nand-0 { + atmel,pins = + <2 8 0x0 0x1 /* PC8 gpio RDY pin pull_up*/ + 2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */ + }; + }; + + macb { + pinctrl_macb_rmii: macb_rmii-0 { + atmel,pins = + <0 10 0x1 0x0 /* PA10 periph A */ + 0 11 0x1 0x0 /* PA11 periph A */ + 0 12 0x1 0x0 /* PA12 periph A */ + 0 13 0x1 0x0 /* PA13 periph A */ + 0 14 0x1 0x0 /* PA14 periph A */ + 0 15 0x1 0x0 /* PA15 periph A */ + 0 16 0x1 0x0 /* PA16 periph A */ + 0 17 0x1 0x0 /* PA17 periph A */ + 0 18 0x1 0x0 /* PA18 periph A */ + 0 19 0x1 0x0>; /* PA19 periph A */ + }; + + pinctrl_macb_rmii_mii: macb_rmii_mii-0 { + atmel,pins = + <0 6 0x2 0x0 /* PA6 periph B */ + 0 7 0x2 0x0 /* PA7 periph B */ + 0 8 0x2 0x0 /* PA8 periph B */ + 0 9 0x2 0x0 /* PA9 periph B */ + 0 27 0x2 0x0 /* PA27 periph B */ + 0 28 0x2 0x0 /* PA28 periph B */ + 0 29 0x2 0x0 /* PA29 periph B */ + 0 30 0x2 0x0>; /* PA30 periph B */ + }; + }; + + mmc0 { + pinctrl_mmc0_slot0_clk_cmd_dat0: mmc0_slot0_clk_cmd_dat0-0 { + atmel,pins = + <0 0 0x1 0x0 /* PA0 periph A */ + 0 1 0x1 0x1 /* PA1 periph A with pullup */ + 0 2 0x1 0x1>; /* PA2 periph A with pullup */ + }; + + pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 { + atmel,pins = + <0 3 0x1 0x1 /* PA3 periph A with pullup */ + 0 4 0x1 0x1 /* PA4 periph A with pullup */ + 0 5 0x1 0x1>; /* PA5 periph A with pullup */ + }; + + pinctrl_mmc0_slot0_dat4_7: mmc0_slot0_dat4_7-0 { + atmel,pins = + <0 6 0x1 0x1 /* PA6 periph A with pullup */ + 0 7 0x1 0x1 /* PA7 periph A with pullup */ + 0 8 0x1 0x1 /* PA8 periph A with pullup */ + 0 9 0x1 0x1>; /* PA9 periph A with pullup */ + }; + }; + + mmc1 { + pinctrl_mmc1_slot0_clk_cmd_dat0: mmc1_slot0_clk_cmd_dat0-0 { + atmel,pins = + <0 31 0x1 0x0 /* PA31 periph A */ + 0 22 0x1 0x1 /* PA22 periph A with pullup */ + 0 23 0x1 0x1>; /* PA23 periph A with pullup */ + }; + + pinctrl_mmc1_slot0_dat1_3: mmc1_slot0_dat1_3-0 { + atmel,pins = + <0 24 0x1 0x1 /* PA24 periph A with pullup */ + 0 25 0x1 0x1 /* PA25 periph A with pullup */ + 0 26 0x1 0x1>; /* PA26 periph A with pullup */ + }; + + pinctrl_mmc1_slot0_dat4_7: mmc1_slot0_dat4_7-0 { + atmel,pins = + <0 27 0x1 0x1 /* PA27 periph A with pullup */ + 0 28 0x1 0x1 /* PA28 periph A with pullup */ + 0 29 0x1 0x1 /* PA29 periph A with pullup */ + 0 20 0x1 0x1>; /* PA30 periph A with pullup */ + }; + }; + + pioA: gpio@fffff200 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff200 0x200>; + interrupts = <2 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioB: gpio@fffff400 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff400 0x200>; + interrupts = <3 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioC: gpio@fffff600 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff600 0x200>; + interrupts = <4 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioD: gpio@fffff800 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff800 0x200>; + interrupts = <5 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioE: gpio@fffffa00 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffffa00 0x200>; + interrupts = <5 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; }; dbgu: serial@ffffee00 { compatible = "atmel,at91sam9260-usart"; reg = <0xffffee00 0x200>; interrupts = <1 4 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dbgu>; status = "disabled"; }; @@ -171,6 +354,8 @@ interrupts = <7 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart0>; status = "disabled"; }; @@ -180,6 +365,8 @@ interrupts = <8 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart1>; status = "disabled"; }; @@ -189,6 +376,8 @@ interrupts = <9 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart2>; status = "disabled"; }; @@ -198,6 +387,8 @@ interrupts = <10 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart3>; status = "disabled"; }; @@ -205,6 +396,8 @@ compatible = "cdns,at32ap7000-macb", "cdns,macb"; reg = <0xfffbc000 0x100>; interrupts = <25 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_macb_rmii>; status = "disabled"; }; @@ -262,6 +455,24 @@ trigger-value = <0x6>; }; }; + + mmc0: mmc@fff80000 { + compatible = "atmel,hsmci"; + reg = <0xfff80000 0x600>; + interrupts = <11 4 0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + mmc1: mmc@fffd0000 { + compatible = "atmel,hsmci"; + reg = <0xfffd0000 0x600>; + interrupts = <29 4 0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; nand0: nand@40000000 { @@ -273,6 +484,8 @@ >; atmel,nand-addr-offset = <21>; atmel,nand-cmd-offset = <22>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nand>; gpios = <&pioC 8 0 &pioC 14 0 0 diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts index 15e1dd43f625..20c31913c270 100644 --- a/arch/arm/boot/dts/at91sam9m10g45ek.dts +++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts @@ -39,6 +39,10 @@ }; usart1: serial@fff90000 { + pinctrl-0 = + <&pinctrl_usart1 + &pinctrl_usart1_rts + &pinctrl_usart1_cts>; status = "okay"; }; @@ -54,6 +58,50 @@ i2c1: i2c@fff88000 { status = "okay"; }; + + mmc0: mmc@fff80000 { + pinctrl-0 = < + &pinctrl_board_mmc0 + &pinctrl_mmc0_slot0_clk_cmd_dat0 + &pinctrl_mmc0_slot0_dat1_3>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 10 0>; + }; + }; + + mmc1: mmc@fffd0000 { + pinctrl-0 = < + &pinctrl_board_mmc1 + &pinctrl_mmc1_slot0_clk_cmd_dat0 + &pinctrl_mmc1_slot0_dat1_3>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 11 0>; + wp-gpios = <&pioD 29 0>; + }; + }; + + pinctrl@fffff200 { + mmc0 { + pinctrl_board_mmc0: mmc0-board { + atmel,pins = + <3 10 0x0 0x5>; /* PD10 gpio CD pin pull up and deglitch */ + }; + }; + + mmc1 { + pinctrl_board_mmc1: mmc1-board { + atmel,pins = + <3 11 0x0 0x5 /* PD11 gpio CD pin pull up and deglitch */ + 3 29 0x0 0x1>; /* PD29 gpio WP pin pull up */ + }; + }; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi index 82508d68aa7e..e9efb34f4379 100644 --- a/arch/arm/boot/dts/at91sam9n12.dtsi +++ b/arch/arm/boot/dts/at91sam9n12.dtsi @@ -84,6 +84,15 @@ reg = <0xfffffe10 0x10>; }; + mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4 0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + tcb0: timer@f8008000 { compatible = "atmel,at91sam9x5-tcb"; reg = <0xf8008000 0x100>; @@ -102,50 +111,186 @@ interrupts = <20 4 0>; }; - pioA: gpio@fffff400 { - compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; - reg = <0xfffff400 0x100>; - interrupts = <2 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + pinctrl@fffff400 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus"; + ranges = <0xfffff400 0xfffff400 0x800>; - pioB: gpio@fffff600 { - compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; - reg = <0xfffff600 0x100>; - interrupts = <2 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + atmel,mux-mask = < + /* A B C */ + 0xffffffff 0xffe07983 0x00000000 /* pioA */ + 0x00040000 0x00047e0f 0x00000000 /* pioB */ + 0xfdffffff 0x07c00000 0xb83fffff /* pioC */ + 0x003fffff 0x003f8000 0x00000000 /* pioD */ + >; - pioC: gpio@fffff800 { - compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; - reg = <0xfffff800 0x100>; - interrupts = <3 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + /* shared pinctrl settings */ + dbgu { + pinctrl_dbgu: dbgu-0 { + atmel,pins = + <0 9 0x1 0x0 /* PA9 periph A */ + 0 10 0x1 0x1>; /* PA10 periph with pullup */ + }; + }; - pioD: gpio@fffffa00 { - compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; - reg = <0xfffffa00 0x100>; - interrupts = <3 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; + usart0 { + pinctrl_usart0: usart0-0 { + atmel,pins = + <0 1 0x1 0x1 /* PA1 periph A with pullup */ + 0 0 0x1 0x0>; /* PA0 periph A */ + }; + + pinctrl_usart0_rts: usart0_rts-0 { + atmel,pins = + <0 2 0x1 0x0>; /* PA2 periph A */ + }; + + pinctrl_usart0_cts: usart0_cts-0 { + atmel,pins = + <0 3 0x1 0x0>; /* PA3 periph A */ + }; + }; + + usart1 { + pinctrl_usart1: usart1-0 { + atmel,pins = + <0 6 0x1 0x1 /* PA6 periph A with pullup */ + 0 5 0x1 0x0>; /* PA5 periph A */ + }; + }; + + usart2 { + pinctrl_usart2: usart2-0 { + atmel,pins = + <0 8 0x1 0x1 /* PA8 periph A with pullup */ + 0 7 0x1 0x0>; /* PA7 periph A */ + }; + + pinctrl_usart2_rts: usart2_rts-0 { + atmel,pins = + <1 0 0x2 0x0>; /* PB0 periph B */ + }; + + pinctrl_usart2_cts: usart2_cts-0 { + atmel,pins = + <1 1 0x2 0x0>; /* PB1 periph B */ + }; + }; + + usart3 { + pinctrl_usart3: usart3-0 { + atmel,pins = + <2 23 0x2 0x1 /* PC23 periph B with pullup */ + 2 22 0x2 0x0>; /* PC22 periph B */ + }; + + pinctrl_usart3_rts: usart3_rts-0 { + atmel,pins = + <2 24 0x2 0x0>; /* PC24 periph B */ + }; + + pinctrl_usart3_cts: usart3_cts-0 { + atmel,pins = + <2 25 0x2 0x0>; /* PC25 periph B */ + }; + }; + + uart0 { + pinctrl_uart0: uart0-0 { + atmel,pins = + <2 9 0x3 0x1 /* PC9 periph C with pullup */ + 2 8 0x3 0x0>; /* PC8 periph C */ + }; + }; + + uart1 { + pinctrl_uart1: uart1-0 { + atmel,pins = + <2 16 0x3 0x1 /* PC17 periph C with pullup */ + 2 17 0x3 0x0>; /* PC16 periph C */ + }; + }; + + nand { + pinctrl_nand: nand-0 { + atmel,pins = + <3 5 0x0 0x1 /* PD5 gpio RDY pin pull_up*/ + 3 4 0x0 0x1>; /* PD4 gpio enable pin pull_up */ + }; + }; + + mmc0 { + pinctrl_mmc0_slot0_clk_cmd_dat0: mmc0_slot0_clk_cmd_dat0-0 { + atmel,pins = + <0 17 0x1 0x0 /* PA17 periph A */ + 0 16 0x1 0x1 /* PA16 periph A with pullup */ + 0 15 0x1 0x1>; /* PA15 periph A with pullup */ + }; + + pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 { + atmel,pins = + <0 18 0x1 0x1 /* PA18 periph A with pullup */ + 0 19 0x1 0x1 /* PA19 periph A with pullup */ + 0 20 0x1 0x1>; /* PA20 periph A with pullup */ + }; + + pinctrl_mmc0_slot0_dat4_7: mmc0_slot0_dat4_7-0 { + atmel,pins = + <0 11 0x2 0x1 /* PA11 periph B with pullup */ + 0 12 0x2 0x1 /* PA12 periph B with pullup */ + 0 13 0x2 0x1 /* PA13 periph B with pullup */ + 0 14 0x2 0x1>; /* PA14 periph B with pullup */ + }; + }; + + pioA: gpio@fffff400 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffff400 0x200>; + interrupts = <2 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioB: gpio@fffff600 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffff600 0x200>; + interrupts = <2 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioC: gpio@fffff800 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffff800 0x200>; + interrupts = <3 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioD: gpio@fffffa00 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffffa00 0x200>; + interrupts = <3 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; }; dbgu: serial@fffff200 { compatible = "atmel,at91sam9260-usart"; reg = <0xfffff200 0x200>; interrupts = <1 4 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dbgu>; status = "disabled"; }; @@ -155,6 +300,8 @@ interrupts = <5 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart0>; status = "disabled"; }; @@ -164,6 +311,8 @@ interrupts = <6 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart1>; status = "disabled"; }; @@ -173,6 +322,8 @@ interrupts = <7 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart2>; status = "disabled"; }; @@ -182,6 +333,8 @@ interrupts = <8 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart3>; status = "disabled"; }; @@ -215,6 +368,8 @@ >; atmel,nand-addr-offset = <21>; atmel,nand-cmd-offset = <22>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nand>; gpios = <&pioD 5 0 &pioD 4 0 0 diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts index 912b2c283d6f..0376bf4fd66b 100644 --- a/arch/arm/boot/dts/at91sam9n12ek.dts +++ b/arch/arm/boot/dts/at91sam9n12ek.dts @@ -45,6 +45,28 @@ i2c1: i2c@f8014000 { status = "okay"; }; + + mmc0: mmc@f0008000 { + pinctrl-0 = < + &pinctrl_board_mmc0 + &pinctrl_mmc0_slot0_clk_cmd_dat0 + &pinctrl_mmc0_slot0_dat1_3>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioA 7 0>; + }; + }; + + pinctrl@fffff400 { + mmc0 { + pinctrl_board_mmc0: mmc0-board { + atmel,pins = + <0 7 0x0 0x5>; /* PA7 gpio CD pin pull up and deglitch */ + }; + }; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9x25.dtsi b/arch/arm/boot/dts/at91sam9x25.dtsi new file mode 100644 index 000000000000..54eb33ba6d22 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9x25.dtsi @@ -0,0 +1,49 @@ +/* + * at91sam9x25.dtsi - Device Tree Include file for AT91SAM9X25 SoC + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ + +/include/ "at91sam9x5.dtsi" + +/ { + model = "Atmel AT91SAM9X25 SoC"; + compatible = "atmel, at91sam9x25, atmel,at91sam9x5"; + + ahb { + apb { + pinctrl@fffff400 { + atmel,mux-mask = < + /* A B C */ + 0xffffffff 0xffe03fff 0xc000001c /* pioA */ + 0x0007ffff 0x00047e3f 0x00000000 /* pioB */ + 0x80000000 0xfffd0000 0xb83fffff /* pioC */ + 0x003fffff 0x003f8000 0x00000000 /* pioD */ + >; + + macb1 { + pinctrl_macb1_rmii: macb1_rmii-0 { + atmel,pins = + <2 16 0x2 0x0 /* PC16 periph B */ + 2 18 0x2 0x0 /* PC18 periph B */ + 2 19 0x2 0x0 /* PC19 periph B */ + 2 20 0x2 0x0 /* PC20 periph B */ + 2 21 0x2 0x0 /* PC21 periph B */ + 2 27 0x2 0x0 /* PC27 periph B */ + 2 28 0x2 0x0 /* PC28 periph B */ + 2 29 0x2 0x0 /* PC29 periph B */ + 2 30 0x2 0x0 /* PC30 periph B */ + 2 31 0x2 0x0>; /* PC31 periph B */ + }; + }; + }; + + macb1: ethernet@f8030000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_macb1_rmii>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9x25ek.dts b/arch/arm/boot/dts/at91sam9x25ek.dts new file mode 100644 index 000000000000..af907eaa1f25 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9x25ek.dts @@ -0,0 +1,16 @@ +/* + * at91sam9x25ek.dts - Device Tree file for AT91SAM9X25-EK board + * + * Copyright (C) 2012 Atmel, + * 2012 Nicolas Ferre <nicolas.ferre@atmel.com> + * + * Licensed under GPLv2 or later. + */ +/dts-v1/; +/include/ "at91sam9x25.dtsi" +/include/ "at91sam9x5ek.dtsi" + +/ { + model = "Atmel AT91SAM9G25-EK"; + compatible = "atmel,at91sam9x25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9"; +}; diff --git a/arch/arm/boot/dts/at91sam9x35.dtsi b/arch/arm/boot/dts/at91sam9x35.dtsi new file mode 100644 index 000000000000..fb102d6126ce --- /dev/null +++ b/arch/arm/boot/dts/at91sam9x35.dtsi @@ -0,0 +1,28 @@ +/* + * at91sam9x35.dtsi - Device Tree Include file for AT91SAM9X35 SoC + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ + +/include/ "at91sam9x5.dtsi" + +/ { + model = "Atmel AT91SAM9X35 SoC"; + compatible = "atmel, at91sam9x35, atmel,at91sam9x5"; + + ahb { + apb { + pinctrl@fffff400 { + atmel,mux-mask = < + /* A B C */ + 0xffffffff 0xffe03fff 0xc000000c /* pioA */ + 0x000406ff 0x00047e3f 0x00000000 /* pioB */ + 0xfdffffff 0x00000000 0xb83fffff /* pioC */ + 0x003fffff 0x003f8000 0x00000000 /* pioD */ + >; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9x35ek.dts b/arch/arm/boot/dts/at91sam9x35ek.dts new file mode 100644 index 000000000000..5ccb607b5414 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9x35ek.dts @@ -0,0 +1,16 @@ +/* + * at91sam9x35ek.dts - Device Tree file for AT91SAM9X35-EK board + * + * Copyright (C) 2012 Atmel, + * 2012 Nicolas Ferre <nicolas.ferre@atmel.com> + * + * Licensed under GPLv2 or later. + */ +/dts-v1/; +/include/ "at91sam9x35.dtsi" +/include/ "at91sam9x5ek.dtsi" + +/ { + model = "Atmel AT91SAM9X35-EK"; + compatible = "atmel,at91sam9x35ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9"; +}; diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index 03fc136421c5..7ee49e8daf98 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -111,50 +111,244 @@ interrupts = <21 4 0>; }; - pioA: gpio@fffff400 { - compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; - reg = <0xfffff400 0x100>; - interrupts = <2 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; - }; + pinctrl@fffff400 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus"; + ranges = <0xfffff400 0xfffff400 0x800>; + + /* shared pinctrl settings */ + dbgu { + pinctrl_dbgu: dbgu-0 { + atmel,pins = + <0 9 0x1 0x0 /* PA9 periph A */ + 0 10 0x1 0x1>; /* PA10 periph A with pullup */ + }; + }; - pioB: gpio@fffff600 { - compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; - reg = <0xfffff600 0x100>; - interrupts = <2 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; + usart0 { + pinctrl_usart0: usart0-0 { + atmel,pins = + <0 0 0x1 0x1 /* PA0 periph A with pullup */ + 0 1 0x1 0x0>; /* PA1 periph A */ + }; + + pinctrl_usart0_rts: usart0_rts-0 { + atmel,pins = + <0 2 0x1 0x0>; /* PA2 periph A */ + }; + + pinctrl_usart0_cts: usart0_cts-0 { + atmel,pins = + <0 3 0x1 0x0>; /* PA3 periph A */ + }; + }; + + usart1 { + pinctrl_usart1: usart1-0 { + atmel,pins = + <0 5 0x1 0x1 /* PA5 periph A with pullup */ + 0 6 0x1 0x0>; /* PA6 periph A */ + }; + + pinctrl_usart1_rts: usart1_rts-0 { + atmel,pins = + <3 27 0x3 0x0>; /* PC27 periph C */ + }; + + pinctrl_usart1_cts: usart1_cts-0 { + atmel,pins = + <3 28 0x3 0x0>; /* PC28 periph C */ + }; + }; + + usart2 { + pinctrl_usart2: usart2-0 { + atmel,pins = + <0 7 0x1 0x1 /* PA7 periph A with pullup */ + 0 8 0x1 0x0>; /* PA8 periph A */ + }; + + pinctrl_uart2_rts: uart2_rts-0 { + atmel,pins = + <0 0 0x2 0x0>; /* PB0 periph B */ + }; + + pinctrl_uart2_cts: uart2_cts-0 { + atmel,pins = + <0 1 0x2 0x0>; /* PB1 periph B */ + }; + }; + + usart3 { + pinctrl_uart3: usart3-0 { + atmel,pins = + <3 23 0x2 0x1 /* PC22 periph B with pullup */ + 3 23 0x2 0x0>; /* PC23 periph B */ + }; + + pinctrl_usart3_rts: usart3_rts-0 { + atmel,pins = + <3 24 0x2 0x0>; /* PC24 periph B */ + }; + + pinctrl_usart3_cts: usart3_cts-0 { + atmel,pins = + <3 25 0x2 0x0>; /* PC25 periph B */ + }; + }; + + uart0 { + pinctrl_uart0: uart0-0 { + atmel,pins = + <3 8 0x3 0x0 /* PC8 periph C */ + 3 9 0x3 0x1>; /* PC9 periph C with pullup */ + }; + }; + + uart1 { + pinctrl_uart1: uart1-0 { + atmel,pins = + <3 16 0x3 0x0 /* PC16 periph C */ + 3 17 0x3 0x1>; /* PC17 periph C with pullup */ + }; + }; + + nand { + pinctrl_nand: nand-0 { + atmel,pins = + <3 4 0x0 0x1 /* PD5 gpio RDY pin pull_up */ + 3 5 0x0 0x1>; /* PD4 gpio enable pin pull_up */ + }; + }; + + macb0 { + pinctrl_macb0_rmii: macb0_rmii-0 { + atmel,pins = + <1 0 0x1 0x0 /* PB0 periph A */ + 1 1 0x1 0x0 /* PB1 periph A */ + 1 2 0x1 0x0 /* PB2 periph A */ + 1 3 0x1 0x0 /* PB3 periph A */ + 1 4 0x1 0x0 /* PB4 periph A */ + 1 5 0x1 0x0 /* PB5 periph A */ + 1 6 0x1 0x0 /* PB6 periph A */ + 1 7 0x1 0x0 /* PB7 periph A */ + 1 9 0x1 0x0 /* PB9 periph A */ + 1 10 0x1 0x0>; /* PB10 periph A */ + }; + + pinctrl_macb0_rmii_mii: macb0_rmii_mii-0 { + atmel,pins = + <1 8 0x1 0x0 /* PA8 periph A */ + 1 11 0x1 0x0 /* PA11 periph A */ + 1 12 0x1 0x0 /* PA12 periph A */ + 1 13 0x1 0x0 /* PA13 periph A */ + 1 14 0x1 0x0 /* PA14 periph A */ + 1 15 0x1 0x0 /* PA15 periph A */ + 1 16 0x1 0x0 /* PA16 periph A */ + 1 17 0x1 0x0>; /* PA17 periph A */ + }; + }; + + mmc0 { + pinctrl_mmc0_slot0_clk_cmd_dat0: mmc0_slot0_clk_cmd_dat0-0 { + atmel,pins = + <0 17 0x1 0x0 /* PA17 periph A */ + 0 16 0x1 0x1 /* PA16 periph A with pullup */ + 0 15 0x1 0x1>; /* PA15 periph A with pullup */ + }; + + pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 { + atmel,pins = + <0 18 0x1 0x1 /* PA18 periph A with pullup */ + 0 19 0x1 0x1 /* PA19 periph A with pullup */ + 0 20 0x1 0x1>; /* PA20 periph A with pullup */ + }; + }; + + mmc1 { + pinctrl_mmc1_slot0_clk_cmd_dat0: mmc1_slot0_clk_cmd_dat0-0 { + atmel,pins = + <0 13 0x2 0x0 /* PA13 periph B */ + 0 12 0x2 0x1 /* PA12 periph B with pullup */ + 0 11 0x2 0x1>; /* PA11 periph B with pullup */ + }; + + pinctrl_mmc1_slot0_dat1_3: mmc1_slot0_dat1_3-0 { + atmel,pins = + <0 2 0x2 0x1 /* PA2 periph B with pullup */ + 0 3 0x2 0x1 /* PA3 periph B with pullup */ + 0 4 0x2 0x1>; /* PA4 periph B with pullup */ + }; + }; + + pioA: gpio@fffff400 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffff400 0x200>; + interrupts = <2 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioB: gpio@fffff600 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffff600 0x200>; + interrupts = <2 4 1>; + #gpio-cells = <2>; + gpio-controller; + #gpio-lines = <19>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioC: gpio@fffff800 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffff800 0x200>; + interrupts = <3 4 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pioD: gpio@fffffa00 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffffa00 0x200>; + interrupts = <3 4 1>; + #gpio-cells = <2>; + gpio-controller; + #gpio-lines = <22>; + interrupt-controller; + #interrupt-cells = <2>; + }; }; - pioC: gpio@fffff800 { - compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; - reg = <0xfffff800 0x100>; - interrupts = <3 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; + mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4 0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; }; - pioD: gpio@fffffa00 { - compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; - reg = <0xfffffa00 0x100>; - interrupts = <3 4 1>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - #interrupt-cells = <2>; + mmc1: mmc@f000c000 { + compatible = "atmel,hsmci"; + reg = <0xf000c000 0x600>; + interrupts = <26 4 0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; }; dbgu: serial@fffff200 { compatible = "atmel,at91sam9260-usart"; reg = <0xfffff200 0x200>; interrupts = <1 4 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dbgu>; status = "disabled"; }; @@ -164,6 +358,8 @@ interrupts = <5 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart0>; status = "disabled"; }; @@ -173,6 +369,8 @@ interrupts = <6 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart1>; status = "disabled"; }; @@ -182,6 +380,8 @@ interrupts = <7 4 5>; atmel,use-dma-rx; atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart2>; status = "disabled"; }; @@ -189,6 +389,8 @@ compatible = "cdns,at32ap7000-macb", "cdns,macb"; reg = <0xf802c000 0x100>; interrupts = <24 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_macb0_rmii>; status = "disabled"; }; @@ -273,6 +475,8 @@ >; atmel,nand-addr-offset = <21>; atmel,nand-cmd-offset = <22>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nand>; gpios = <&pioD 5 0 &pioD 4 0 0 diff --git a/arch/arm/boot/dts/at91sam9x5ek.dtsi b/arch/arm/boot/dts/at91sam9x5ek.dtsi new file mode 100644 index 000000000000..8a7cf1d9cf5d --- /dev/null +++ b/arch/arm/boot/dts/at91sam9x5ek.dtsi @@ -0,0 +1,101 @@ +/* + * at91sam9x5ek.dtsi - Device Tree file for AT91SAM9x5CM Base board + * + * Copyright (C) 2012 Atmel, + * 2012 Nicolas Ferre <nicolas.ferre@atmel.com> + * + * Licensed under GPLv2 or later. + */ +/include/ "at91sam9x5cm.dtsi" + +/ { + model = "Atmel AT91SAM9X5-EK"; + compatible = "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9"; + + chosen { + bootargs = "128M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs"; + }; + + ahb { + apb { + mmc0: mmc@f0008000 { + pinctrl-0 = < + &pinctrl_board_mmc0 + &pinctrl_mmc0_slot0_clk_cmd_dat0 + &pinctrl_mmc0_slot0_dat1_3>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 0>; + }; + }; + + mmc1: mmc@f000c000 { + pinctrl-0 = < + &pinctrl_board_mmc1 + &pinctrl_mmc1_slot0_clk_cmd_dat0 + &pinctrl_mmc1_slot0_dat1_3>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 14 0>; + }; + }; + + dbgu: serial@fffff200 { + status = "okay"; + }; + + usart0: serial@f801c000 { + status = "okay"; + }; + + macb0: ethernet@f802c000 { + phy-mode = "rmii"; + status = "okay"; + }; + + i2c0: i2c@f8010000 { + status = "okay"; + }; + + i2c1: i2c@f8014000 { + status = "okay"; + }; + + i2c2: i2c@f8018000 { + status = "okay"; + }; + + pinctrl@fffff400 { + mmc0 { + pinctrl_board_mmc0: mmc0-board { + atmel,pins = + <3 15 0x0 0x5>; /* PD15 gpio CD pin pull up and deglitch */ + }; + }; + + mmc1 { + pinctrl_board_mmc1: mmc1-board { + atmel,pins = + <3 14 0x0 0x5>; /* PD14 gpio CD pin pull up and deglitch */ + }; + }; + }; + }; + + usb0: ohci@00600000 { + status = "okay"; + num-ports = <2>; + atmel,vbus-gpio = <&pioD 19 1 + &pioD 20 1 + >; + }; + + usb1: ehci@00700000 { + status = "okay"; + }; + }; +}; diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts new file mode 100644 index 000000000000..387fedb58988 --- /dev/null +++ b/arch/arm/boot/dts/pm9g45.dts @@ -0,0 +1,165 @@ +/* + * pm9g45.dts - Device Tree file for Ronetix pm9g45 board + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ +/dts-v1/; +/include/ "at91sam9g45.dtsi" + +/ { + model = "Ronetix pm9g45"; + compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + reg = <0x70000000 0x8000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + }; + + ahb { + apb { + dbgu: serial@ffffee00 { + status = "okay"; + }; + + pinctrl@fffff200 { + + board { + pinctrl_board_nand: nand0-board { + atmel,pins = + <3 3 0x0 0x1 /* PD3 gpio RDY pin pull_up*/ + 2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */ + }; + }; + + mmc { + pinctrl_board_mmc: mmc0-board { + atmel,pins = + <3 6 0x0 0x5>; /* PD6 gpio CD pin pull_up and deglitch */ + }; + }; + }; + + mmc0: mmc@fff80000 { + pinctrl-0 = < + &pinctrl_board_mmc + &pinctrl_mmc0_slot0_clk_cmd_dat0 + &pinctrl_mmc0_slot0_dat1_3>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 6 0>; + }; + }; + + macb0: ethernet@fffbc000 { + phy-mode = "rmii"; + status = "okay"; + }; + + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + pinctrl-0 = <&pinctrl_board_nand>; + + gpios = <&pioD 3 0 + &pioC 14 0 + 0 + >; + + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x20000>; + }; + + barebox@20000 { + label = "barebox"; + reg = <0x20000 0x40000>; + }; + + bareboxenv@60000 { + label = "bareboxenv"; + reg = <0x60000 0x1A0000>; + }; + + kernel@200000 { + label = "bareboxenv2"; + reg = <0x200000 0x300000>; + }; + + kernel@500000 { + label = "root"; + reg = <0x500000 0x400000>; + }; + + data@900000 { + label = "data"; + reg = <0x900000 0x8340000>; + }; + }; + + usb0: ohci@00700000 { + status = "okay"; + num-ports = <2>; + }; + + usb1: ehci@00800000 { + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + + led0 { + label = "led0"; + gpios = <&pioD 0 1>; + linux,default-trigger = "nand-disk"; + }; + + led1 { + label = "led1"; + gpios = <&pioD 31 0>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + right { + label = "SW4"; + gpios = <&pioE 7 1>; + linux,code = <106>; + }; + + up { + label = "SW3"; + gpios = <&pioE 8 1>; + linux,code = <103>; + }; + }; +}; diff --git a/arch/arm/boot/dts/spear1310-evb.dts b/arch/arm/boot/dts/spear1310-evb.dts index dd4358bc26e2..2e4c5727468e 100644 --- a/arch/arm/boot/dts/spear1310-evb.dts +++ b/arch/arm/boot/dts/spear1310-evb.dts @@ -181,6 +181,10 @@ status = "okay"; }; + gpio@d8400000 { + status = "okay"; + }; + i2c0: i2c@e0280000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/spear1310.dtsi b/arch/arm/boot/dts/spear1310.dtsi index 419ea7413d23..7cd25eb4f8e0 100644 --- a/arch/arm/boot/dts/spear1310.dtsi +++ b/arch/arm/boot/dts/spear1310.dtsi @@ -70,6 +70,12 @@ status = "disabled"; }; + pinmux: pinmux@e0700000 { + compatible = "st,spear1310-pinmux"; + reg = <0xe0700000 0x1000>; + #gpio-range-cells = <2>; + }; + spi1: spi@5d400000 { compatible = "arm,pl022", "arm,primecell"; reg = <0x5d400000 0x1000>; @@ -179,6 +185,27 @@ thermal@e07008c4 { st,thermal-flags = <0x7000>; }; + + gpiopinctrl: gpio@d8400000 { + compatible = "st,spear-plgpio"; + reg = <0xd8400000 0x1000>; + interrupts = <0 100 0x4>; + #interrupt-cells = <1>; + interrupt-controller; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinmux 0 246>; + status = "disabled"; + + st-plgpio,ngpio = <246>; + st-plgpio,enb-reg = <0xd0>; + st-plgpio,wdata-reg = <0x90>; + st-plgpio,dir-reg = <0xb0>; + st-plgpio,ie-reg = <0x30>; + st-plgpio,rdata-reg = <0x70>; + st-plgpio,mis-reg = <0x10>; + st-plgpio,eit-reg = <0x50>; + }; }; }; }; diff --git a/arch/arm/boot/dts/spear1340-evb.dts b/arch/arm/boot/dts/spear1340-evb.dts index c9a54e06fb68..045f7123ffac 100644 --- a/arch/arm/boot/dts/spear1340-evb.dts +++ b/arch/arm/boot/dts/spear1340-evb.dts @@ -193,6 +193,10 @@ status = "okay"; }; + gpio@e2800000 { + status = "okay"; + }; + i2c0: i2c@e0280000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/spear1340.dtsi b/arch/arm/boot/dts/spear1340.dtsi index d71fe2a68f09..6c09eb0a1b2b 100644 --- a/arch/arm/boot/dts/spear1340.dtsi +++ b/arch/arm/boot/dts/spear1340.dtsi @@ -24,6 +24,12 @@ status = "disabled"; }; + pinmux: pinmux@e0700000 { + compatible = "st,spear1340-pinmux"; + reg = <0xe0700000 0x1000>; + #gpio-range-cells = <2>; + }; + spi1: spi@5d400000 { compatible = "arm,pl022", "arm,primecell"; reg = <0x5d400000 0x1000>; @@ -51,6 +57,26 @@ thermal@e07008c4 { st,thermal-flags = <0x2a00>; }; + + gpiopinctrl: gpio@e2800000 { + compatible = "st,spear-plgpio"; + reg = <0xe2800000 0x1000>; + interrupts = <0 107 0x4>; + #interrupt-cells = <1>; + interrupt-controller; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinmux 0 252>; + status = "disabled"; + + st-plgpio,ngpio = <250>; + st-plgpio,wdata-reg = <0x40>; + st-plgpio,dir-reg = <0x00>; + st-plgpio,ie-reg = <0x80>; + st-plgpio,rdata-reg = <0x20>; + st-plgpio,mis-reg = <0xa0>; + st-plgpio,eit-reg = <0x60>; + }; }; }; }; diff --git a/arch/arm/boot/dts/spear310.dtsi b/arch/arm/boot/dts/spear310.dtsi index 62fc4fb3e5f9..930303e48df9 100644 --- a/arch/arm/boot/dts/spear310.dtsi +++ b/arch/arm/boot/dts/spear310.dtsi @@ -22,9 +22,10 @@ 0xb0000000 0xb0000000 0x10000000 0xd0000000 0xd0000000 0x30000000>; - pinmux@b4000000 { + pinmux: pinmux@b4000000 { compatible = "st,spear310-pinmux"; reg = <0xb4000000 0x1000>; + #gpio-range-cells = <2>; }; fsmc: flash@44000000 { @@ -75,6 +76,25 @@ reg = <0xb2200000 0x1000>; status = "disabled"; }; + + gpiopinctrl: gpio@b4000000 { + compatible = "st,spear-plgpio"; + reg = <0xb4000000 0x1000>; + #interrupt-cells = <1>; + interrupt-controller; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinmux 0 102>; + status = "disabled"; + + st-plgpio,ngpio = <102>; + st-plgpio,enb-reg = <0x10>; + st-plgpio,wdata-reg = <0x20>; + st-plgpio,dir-reg = <0x30>; + st-plgpio,ie-reg = <0x50>; + st-plgpio,rdata-reg = <0x40>; + st-plgpio,mis-reg = <0x60>; + }; }; }; }; diff --git a/arch/arm/boot/dts/spear320-evb.dts b/arch/arm/boot/dts/spear320-evb.dts index 082328bd64ab..ad4bfc68ee05 100644 --- a/arch/arm/boot/dts/spear320-evb.dts +++ b/arch/arm/boot/dts/spear320-evb.dts @@ -164,6 +164,10 @@ status = "okay"; }; + gpio@b3000000 { + status = "okay"; + }; + i2c0: i2c@d0180000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/spear320.dtsi b/arch/arm/boot/dts/spear320.dtsi index 1f49d69595a0..67d7ada71275 100644 --- a/arch/arm/boot/dts/spear320.dtsi +++ b/arch/arm/boot/dts/spear320.dtsi @@ -21,9 +21,10 @@ ranges = <0x40000000 0x40000000 0x80000000 0xd0000000 0xd0000000 0x30000000>; - pinmux@b3000000 { + pinmux: pinmux@b3000000 { compatible = "st,spear320-pinmux"; reg = <0xb3000000 0x1000>; + #gpio-range-cells = <2>; }; clcd@90000000 { @@ -90,6 +91,26 @@ reg = <0xa4000000 0x1000>; status = "disabled"; }; + + gpiopinctrl: gpio@b3000000 { + compatible = "st,spear-plgpio"; + reg = <0xb3000000 0x1000>; + #interrupt-cells = <1>; + interrupt-controller; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinmux 0 102>; + status = "disabled"; + + st-plgpio,ngpio = <102>; + st-plgpio,enb-reg = <0x24>; + st-plgpio,wdata-reg = <0x34>; + st-plgpio,dir-reg = <0x44>; + st-plgpio,ie-reg = <0x64>; + st-plgpio,rdata-reg = <0x54>; + st-plgpio,mis-reg = <0x84>; + st-plgpio,eit-reg = <0x94>; + }; }; }; }; |