diff options
Diffstat (limited to 'Documentation')
184 files changed, 5973 insertions, 3342 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index df42bed09f25..35289d47d6cb 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -1743,6 +1743,16 @@ Description: Raw counter device counters direction for channel Y. +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_label +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_label +KernelVersion: 5.8 +Contact: linux-iio@vger.kernel.org +Description: + Optional symbolic label to a device channel. + If a label is defined for this channel add that to the channel + specific attributes. This is useful for userspace to be able to + better identify an individual channel. + What: /sys/bus/iio/devices/iio:deviceX/in_phaseY_raw KernelVersion: 4.18 Contact: linux-iio@vger.kernel.org diff --git a/Documentation/ABI/testing/sysfs-bus-iio-adc-mt6360 b/Documentation/ABI/testing/sysfs-bus-iio-adc-mt6360 new file mode 100644 index 000000000000..e5a7b1c7cca3 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-adc-mt6360 @@ -0,0 +1,78 @@ +What: /sys/bus/iio/devices/iio:deviceX/in_voltage0_raw +KernelVersion: 5.8.0 +Contact: gene_chen@richtek.com +Description: + Indicated MT6360 USBID ADC which connected to connector ID pin. + Calculating with scale and offset returns voltage in uV + +What: /sys/bus/iio/devices/iio:deviceX/in_voltage1_raw +KernelVersion: 5.8.0 +Contact: gene_chen@richtek.com +Description: + Indicated MT6360 VBUS ADC with lower accuracy(+-75mA) + higher measure range(1~22mV) + Calculating with scale and offset returns voltage in uV + +What: /sys/bus/iio/devices/iio:deviceX/in_voltage2_raw +KernelVersion: 5.8.0 +Contact: gene_chen@richtek.com +Description: + Indicated MT6360 VBUS ADC with higher accuracy(+-30mA) + lower measure range(1~9.76V) + Calculating with scale and offset returns voltage in uV + +What: /sys/bus/iio/devices/iio:deviceX/in_voltage3_raw +KernelVersion: 5.8.0 +Contact: gene_chen@richtek.com +Description: + Indicated MT6360 VSYS ADC + Calculating with scale and offset returns voltage in uV + +What: /sys/bus/iio/devices/iio:deviceX/in_voltage4_raw +KernelVersion: 5.8.0 +Contact: gene_chen@richtek.com +Description: + Indicated MT6360 VBAT ADC + Calculating with scale and offset returns voltage in uV + +What: /sys/bus/iio/devices/iio:deviceX/in_current5_raw +KernelVersion: 5.8.0 +Contact: gene_chen@richtek.com +Description: + Indicated MT6360 IBUS ADC + Calculating with scale and offset returns voltage in uA + +What: /sys/bus/iio/devices/iio:deviceX/in_current6_raw +KernelVersion: 5.8.0 +Contact: gene_chen@richtek.com +Description: + Indicated MT6360 IBAT ADC + Calculating with scale and offset returns voltage in uA + +What: /sys/bus/iio/devices/iio:deviceX/in_current7_raw +KernelVersion: 5.8.0 +Contact: gene_chen@richtek.com +Description: + Indicated MT6360 CHG_VDDP ADC + Calculating with scale and offset returns voltage in uV + +What: /sys/bus/iio/devices/iio:deviceX/in_temp8_raw +KernelVersion: 5.8.0 +Contact: gene_chen@richtek.com +Description: + Indicated MT6360 IC junction temperature + Calculating with scale and offset returns temperature in degree + +What: /sys/bus/iio/devices/iio:deviceX/in_voltage9_raw +KernelVersion: 5.8.0 +Contact: gene_chen@richtek.com +Description: + Indicated MT6360 VREF_TS ADC + Calculating with scale and offset returns voltage in uV + +What: /sys/bus/iio/devices/iio:deviceX/in_voltage10_raw +KernelVersion: 5.8.0 +Contact: gene_chen@richtek.com +Description: + Indicated MT6360 TS ADC + Calculating with scale and offset returns voltage in uV diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt b/Documentation/devicetree/bindings/iio/accel/bma180.txt deleted file mode 100644 index 33da4a6fdb39..000000000000 --- a/Documentation/devicetree/bindings/iio/accel/bma180.txt +++ /dev/null @@ -1,35 +0,0 @@ -* Bosch BMA023 / BMA150/ BMA180 / BMA25x / SMB380 triaxial acceleration sensor - -https://media.digikey.com/pdf/Data%20Sheets/Bosch/BMA150.pdf -http://omapworld.com/BMA180_111_1002839.pdf -http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf - -Required properties: - - - compatible : should be one of: - "bosch,bma023" - "bosch,bma150" - "bosch,bma180" - "bosch,bma250" - "bosch,bma254" - "bosch,smb380" - - reg : the I2C address of the sensor - - vdd-supply : regulator phandle connected to the VDD pin - - vddio-supply : regulator phandle connected to the VDDIO pin - -Optional properties: - - - interrupts : interrupt mapping for GPIO IRQ, it should by configured with - flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING - For the bma250 the first interrupt listed must be the one - connected to the INT1 pin, the second (optional) interrupt - listed must be the one connected to the INT2 pin. - -Example: - -bma180@40 { - compatible = "bosch,bma180"; - reg = <0x40>; - interrupt-parent = <&gpio6>; - interrupts = <18 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; -}; diff --git a/Documentation/devicetree/bindings/iio/accel/bosch,bma180.yaml b/Documentation/devicetree/bindings/iio/accel/bosch,bma180.yaml new file mode 100644 index 000000000000..45b3abde298f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/bosch,bma180.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/accel/bosch,bma180.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bosch BMA023 / BMA150/ BMA180 / BMA25x / SMB380 triaxial accelerometers + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: | + https://media.digikey.com/pdf/Data%20Sheets/Bosch/BMA150.pdf + http://omapworld.com/BMA180_111_1002839.pdf + http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf + +properties: + compatible: + enum: + - bosch,bma023 + - bosch,bma150 + - bosch,bma180 + - bosch,bma250 + - bosch,bma254 + - bosch,smb380 + + reg: + maxItems: 1 + + vdd-supply: true + + vddio-supply: true + + interrupts: + minItems: 1 + maxItems: 2 + description: | + Type should be either IRQ_TYPE_LEVEL_HIGH or IRQ_TYPE_EDGE_RISING. + For the bma250 the first interrupt listed must be the one + connected to the INT1 pin, the second (optional) interrupt + listed must be the one connected to the INT2 pin. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + accel@40 { + compatible = "bosch,bma180"; + reg = <0x40>; + interrupt-parent = <&gpio6>; + interrupts = <18 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/accel/bosch,bma255.yaml b/Documentation/devicetree/bindings/iio/accel/bosch,bma255.yaml new file mode 100644 index 000000000000..6eef3480ea8f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/bosch,bma255.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/accel/bosch,bma255.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bosch BMA255 and Similar Accelerometers + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: + 3 axis accelerometers with varying range and I2C or SPI + 4-wire interface. + +properties: + compatible: + enum: + - bosch,bmc150 + - bosch,bmi055 + - bosch,bma255 + - bosch,bma250e + - bosch,bma222 + - bosch,bma222e + - bosch,bma280 + + reg: + maxItems: 1 + + vdd-supply: true + vddio-supply: true + + interrupts: + maxItems: 1 + + mount-matrix: + description: an optional 3x3 mounting rotation matrix. + + spi-max-frequency: + maximum: 10000000 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + accelerometer@8 { + compatible = "bosch,bma222"; + reg = <0x08>; + vddio-supply = <&vddio>; + vdd-supply = <&vdd>; + interrupts = <57 IRQ_TYPE_EDGE_FALLING>; + }; + }; + - | + # include <dt-bindings/interrupt-controller/irq.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + accel@0 { + compatible = "bosch,bma222"; + reg = <0>; + spi-max-frequency = <10000000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/accel/dmard06.txt b/Documentation/devicetree/bindings/iio/accel/dmard06.txt deleted file mode 100644 index ce105a12c645..000000000000 --- a/Documentation/devicetree/bindings/iio/accel/dmard06.txt +++ /dev/null @@ -1,19 +0,0 @@ -Device tree bindings for Domintech DMARD05, DMARD06, DMARD07 accelerometers - -Required properties: - - compatible : Should be "domintech,dmard05" - or "domintech,dmard06" - or "domintech,dmard07" - - reg : I2C address of the chip. Should be 0x1c - -Example: - &i2c1 { - /* ... */ - - accelerometer@1c { - compatible = "domintech,dmard06"; - reg = <0x1c>; - }; - - /* ... */ - }; diff --git a/Documentation/devicetree/bindings/iio/accel/fsl,mma8452.yaml b/Documentation/devicetree/bindings/iio/accel/fsl,mma8452.yaml new file mode 100644 index 000000000000..b0dd2b4e116a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/fsl,mma8452.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/accel/fsl,mma8452.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: + Freescale MMA8451Q, MMA8452Q, MMA8453Q, MMA8652FC, MMA8653FC or FXLS8471Q + triaxial accelerometer + +maintainers: + - Martin Kepplinger <martin.kepplinger@theobroma-systems.com> + +properties: + compatible: + enum: + - fsl,mma8451 + - fsl,mma8452 + - fsl,mma8453 + - fsl,mma8652 + - fsl,mma8653 + - fsl,fxls8471 + + reg: + maxItems: 1 + + interrupts: + description: + 2 highly configurable interrupt lines exist. + minItems: 1 + maxItems: 2 + + interrupt-names: + description: Specify which interrupt line is in use. + items: + enum: + - INT1 + - INT2 + minItems: 1 + maxItems: 2 + + vdd-supply: true + vddio-supply: true + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + accel@1d { + compatible = "fsl,mma8453"; + reg = <0x1d>; + interrupt-parent = <&gpio1>; + interrupts = <5 0>; + interrupt-names = "INT2"; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.txt b/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.txt deleted file mode 100644 index ce950e162d5d..000000000000 --- a/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.txt +++ /dev/null @@ -1,24 +0,0 @@ -Kionix KXCJK-1013 Accelerometer device tree bindings - -Required properties: - -- compatible: Must be one of: - "kionix,kxcjk1013" - "kionix,kxcj91008" - "kionix,kxtj21009" - "kionix,kxtf9" - - reg: i2c slave address - -Optional properties: - - - mount-matrix: an optional 3x3 mounting rotation matrix - -Example: - -kxtf9@f { - compatible = "kionix,kxtf9"; - reg = <0x0F>; - mount-matrix = "0", "1", "0", - "1", "0", "0", - "0", "0", "1"; -}; diff --git a/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.yaml b/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.yaml new file mode 100644 index 000000000000..5667d09dfe6a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.yaml @@ -0,0 +1,46 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/accel/kionix,kxcjk1013.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Kionix KXCJK-1013 Accelerometer + +maintainers: + - Robert Yang <decatf@gmail.com> + +properties: + compatible: + enum: + - kionix,kxcjk1013 + - kionix,kxcj91008 + - kionix,kxtj21009 + - kionix,kxtf9 + + reg: + maxItems: 1 + + mount-matrix: + description: an optional 3x3 mounting rotation matrix. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + accel@f { + compatible = "kionix,kxtf9"; + reg = <0x0F>; + mount-matrix = "0", "1", "0", + "1", "0", "0", + "0", "0", "1"; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt deleted file mode 100644 index e132394375a1..000000000000 --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt +++ /dev/null @@ -1,35 +0,0 @@ -Freescale MMA8451Q, MMA8452Q, MMA8453Q, MMA8652FC, MMA8653FC or FXLS8471Q -triaxial accelerometer - -Required properties: - - - compatible: should contain one of - * "fsl,mma8451" - * "fsl,mma8452" - * "fsl,mma8453" - * "fsl,mma8652" - * "fsl,mma8653" - * "fsl,fxls8471" - - - reg: the I2C address of the chip - -Optional properties: - - - interrupts: interrupt mapping for GPIO IRQ - - - interrupt-names: should contain "INT1" and/or "INT2", the accelerometer's - interrupt line in use. - - - vdd-supply: phandle to the regulator that provides vdd power to the accelerometer. - - - vddio-supply: phandle to the regulator that provides vddio power to the accelerometer. - -Example: - - mma8453fc@1d { - compatible = "fsl,mma8453"; - reg = <0x1d>; - interrupt-parent = <&gpio1>; - interrupts = <5 0>; - interrupt-names = "INT2"; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/adc.txt b/Documentation/devicetree/bindings/iio/adc/adc.txt deleted file mode 100644 index 5bbaa330a250..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/adc.txt +++ /dev/null @@ -1,23 +0,0 @@ -Common ADCs properties - -Optional properties for child nodes: -- bipolar : Boolean, if set the channel is used in bipolar mode. -- diff-channels : Differential channels muxed for this ADC. The first value - specifies the positive input pin, the second value the negative - input pin. - -Example: - adc@0 { - compatible = "some,adc"; - ... - channel@0 { - bipolar; - diff-channels = <0 1>; - ... - }; - - channel@1 { - diff-channels = <2 3>; - ... - }; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/adc.yaml b/Documentation/devicetree/bindings/iio/adc/adc.yaml new file mode 100644 index 000000000000..912a7635edc4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adc.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/adc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic IIO bindings for ADC channels + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: + A few properties are defined in a common way ADC channels. + +properties: + $nodename: + pattern: "^channel(@[0-9a-f]+)?$" + description: + A channel index should match reg. + + reg: + maxItems: 1 + + label: + $ref: /schemas/types.yaml#/definitions/string + description: Unique name to identify which channel this is. + + bipolar: + $ref: /schemas/types.yaml#/definitions/flag + description: If provided, the channel is to be used in bipolar mode. + + diff-channels: + $ref: /schemas/types.yaml#/definitions/uint32-array + maxItems: 2 + minItems: 2 + description: + Many ADCs have dual Muxes to allow different input pins to be routed + to both the positive and negative inputs of a differential ADC. + The first value specifies the positive input pin, the second + specifies the negative input pin. + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml index f1c574c896cb..fb3d0dae9bae 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml @@ -63,10 +63,10 @@ required: patternProperties: "^channel@([0-9]|1[0-5])$": + $ref: "adc.yaml" type: object description: | Represents the external channels which are connected to the ADC. - See Documentation/devicetree/bindings/iio/adc/adc.txt. properties: reg: @@ -88,15 +88,9 @@ patternProperties: $ref: /schemas/types.yaml#/definitions/uint32 enum: [0, 1, 3] - diff-channels: - description: see Documentation/devicetree/bindings/iio/adc/adc.txt - items: - minimum: 0 - maximum: 15 + diff-channels: true - bipolar: - description: see Documentation/devicetree/bindings/iio/adc/adc.txt - type: boolean + bipolar: true adi,buffered-positive: description: Enable buffered mode for positive input. @@ -110,6 +104,8 @@ patternProperties: - reg - diff-channels + additionalProperties: false + additionalProperties: false examples: diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7292.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7292.yaml index 108d202b288f..a3e39a40c9b3 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7292.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7292.yaml @@ -45,10 +45,10 @@ required: patternProperties: "^channel@[0-7]$": + $ref: "adc.yaml" type: object description: | Represents the external channels which are connected to the ADC. - See Documentation/devicetree/bindings/iio/adc/adc.txt. properties: reg: @@ -58,13 +58,13 @@ patternProperties: - minimum: 0 maximum: 7 - diff-channels: - description: see Documentation/devicetree/bindings/iio/adc/adc.txt - maxItems: 1 + diff-channels: true required: - reg + additionalProperties: true + additionalProperties: false examples: diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.yaml index 8f32800fe5b7..924477dfb833 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.yaml @@ -29,6 +29,12 @@ properties: interrupts: maxItems: 1 + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + vref-supply: description: ADC reference voltage supply @@ -62,6 +68,24 @@ required: - spi-cpha - adi,sync-in-gpios +patternProperties: + "^channel@([0-9]|1[0-5])$": + type: object + description: | + Represents the external channels which are connected to the device. + + properties: + reg: + description: | + The channel number. + + label: + description: | + Unique name to identify which channel this is. + required: + - reg + additionalProperties: false + additionalProperties: false examples: @@ -85,6 +109,14 @@ examples: reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>; clocks = <&ad7768_mclk>; clock-names = "mclk"; + + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { + reg = <0>; + label = "channel_0"; + }; }; }; ... diff --git a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt deleted file mode 100644 index 07c59f301b31..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt +++ /dev/null @@ -1,50 +0,0 @@ -* AT91 SAMA5D2 Analog to Digital Converter (ADC) - -Required properties: - - compatible: Should be "atmel,sama5d2-adc" or "microchip,sam9x60-adc". - - reg: Should contain ADC registers location and length. - - interrupts: Should contain the IRQ line for the ADC. - - clocks: phandle to device clock. - - clock-names: Must be "adc_clk". - - vref-supply: Supply used as reference for conversions. - - vddana-supply: Supply for the adc device. - - atmel,min-sample-rate-hz: Minimum sampling rate, it depends on SoC. - - atmel,max-sample-rate-hz: Maximum sampling rate, it depends on SoC. - - atmel,startup-time-ms: Startup time expressed in ms, it depends on SoC. - - atmel,trigger-edge-type: One of possible edge types for the ADTRG hardware - trigger pin. When the specific edge type is detected, the conversion will - start. Possible values are rising, falling, or both. - This property uses the IRQ edge types values: IRQ_TYPE_EDGE_RISING , - IRQ_TYPE_EDGE_FALLING or IRQ_TYPE_EDGE_BOTH - -Optional properties: - - dmas: Phandle to dma channel for the ADC. - - dma-names: Must be "rx" when dmas property is being used. - See ../../dma/dma.txt for details. - - #io-channel-cells: in case consumer drivers are attached, this must be 1. - See <Documentation/devicetree/bindings/iio/iio-bindings.txt> for details. - -Properties for consumer drivers: - - Consumer drivers can be connected to this producer device, as specified - in <Documentation/devicetree/bindings/iio/iio-bindings.txt> - - Channels exposed are specified in: - <dt-bindings/iio/adc/at91-sama5d2_adc.txt> - -Example: - -adc: adc@fc030000 { - compatible = "atmel,sama5d2-adc"; - reg = <0xfc030000 0x100>; - interrupts = <40 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&adc_clk>; - clock-names = "adc_clk"; - atmel,min-sample-rate-hz = <200000>; - atmel,max-sample-rate-hz = <20000000>; - atmel,startup-time-ms = <4>; - vddana-supply = <&vdd_3v3_lp_reg>; - vref-supply = <&vdd_3v3_lp_reg>; - atmel,trigger-edge-type = <IRQ_TYPE_EDGE_BOTH>; - dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(25))>; - dma-names = "rx"; - #io-channel-cells = <1>; -} diff --git a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt deleted file mode 100644 index f65b04fb7962..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt +++ /dev/null @@ -1,83 +0,0 @@ -* AT91's Analog to Digital Converter (ADC) - -Required properties: - - compatible: Should be "atmel,<chip>-adc" - <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5" - - reg: Should contain ADC registers location and length - - interrupts: Should contain the IRQ line for the ADC - - clock-names: tuple listing input clock names. - Required elements: "adc_clk", "adc_op_clk". - - clocks: phandles to input clocks. - - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this - device - - atmel,adc-startup-time: Startup Time of the ADC in microseconds as - defined in the datasheet - - atmel,adc-vref: Reference voltage in millivolts for the conversions - - atmel,adc-res: List of resolutions in bits supported by the ADC. List size - must be two at least. - - atmel,adc-res-names: Contains one identifier string for each resolution - in atmel,adc-res property. "lowres" and "highres" - identifiers are required. - -Optional properties: - - atmel,adc-use-external-triggers: Boolean to enable the external triggers - - atmel,adc-use-res: String corresponding to an identifier from - atmel,adc-res-names property. If not specified, the highest - resolution will be used. - - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion - - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds - - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this - value is set, then the adc driver will enable touchscreen - support. - NOTE: when adc touchscreen is enabled, the adc hardware trigger will be - disabled. Since touchscreen will occupy the trigger register. - - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It - makes touch detection more precise. - -Optional trigger Nodes: - - Required properties: - * trigger-name: Name of the trigger exposed to the user - * trigger-value: Value to put in the Trigger register - to activate this trigger - - Optional properties: - * trigger-external: Is the trigger an external trigger? - -Examples: -adc0: adc@fffb0000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "atmel,at91sam9260-adc"; - reg = <0xfffb0000 0x100>; - interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&adc_clk>, <&adc_op_clk>; - clock-names = "adc_clk", "adc_op_clk"; - atmel,adc-channels-used = <0xff>; - atmel,adc-startup-time = <40>; - atmel,adc-use-external-triggers; - atmel,adc-vref = <3300>; - atmel,adc-res = <8 10>; - atmel,adc-res-names = "lowres", "highres"; - atmel,adc-use-res = "lowres"; - - trigger0 { - trigger-name = "external-rising"; - trigger-value = <0x1>; - trigger-external; - }; - trigger1 { - trigger-name = "external-falling"; - trigger-value = <0x2>; - trigger-external; - }; - - trigger2 { - trigger-name = "external-any"; - trigger-value = <0x3>; - trigger-external; - }; - - trigger3 { - trigger-name = "continuous"; - trigger-value = <0x6>; - }; -}; diff --git a/Documentation/devicetree/bindings/iio/adc/atmel,sama5d2-adc.yaml b/Documentation/devicetree/bindings/iio/adc/atmel,sama5d2-adc.yaml new file mode 100644 index 000000000000..79c13b408eda --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/atmel,sama5d2-adc.yaml @@ -0,0 +1,101 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/atmel,sama5d2-adc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: AT91 SAMA5D2 Analog to Digital Converter (ADC) + +maintainers: + - Ludovic Desroches <ludovic.desroches@atmel.com> + - Eugen Hristev <eugen.hristev@microchip.com> + +properties: + compatible: + enum: + - atmel,sama5d2-adc + - microchip,sam9x60-adc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: adc_clk + + vref-supply: true + vddana-supply: true + + atmel,min-sample-rate-hz: + description: Minimum sampling rate, it depends on SoC. + + atmel,max-sample-rate-hz: + description: Maximum sampling rate, it depends on SoC. + + atmel,startup-time-ms: + description: Startup time expressed in ms, it depends on SoC. + + atmel,trigger-edge-type: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: + One of possible edge types for the ADTRG hardware trigger pin. + When the specific edge type is detected, the conversion will + start. Should be one of IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING + or IRQ_TYPE_EDGE_BOTH. + enum: [1, 2, 3] + + dmas: + maxItems: 1 + + dma-names: + const: rx + + "#io-channel-cells": + const: 1 + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - vref-supply + - vddana-supply + - atmel,min-sample-rate-hz + - atmel,max-sample-rate-hz + - atmel,startup-time-ms + - atmel,trigger-edge-type + +examples: + - | + #include <dt-bindings/dma/at91.h> + #include <dt-bindings/interrupt-controller/irq.h> + soc { + #address-cells = <1>; + #size-cells = <1>; + + adc@fc030000 { + compatible = "atmel,sama5d2-adc"; + reg = <0xfc030000 0x100>; + interrupts = <40 IRQ_TYPE_LEVEL_HIGH 7>; + clocks = <&adc_clk>; + clock-names = "adc_clk"; + atmel,min-sample-rate-hz = <200000>; + atmel,max-sample-rate-hz = <20000000>; + atmel,startup-time-ms = <4>; + vddana-supply = <&vdd_3v3_lp_reg>; + vref-supply = <&vdd_3v3_lp_reg>; + atmel,trigger-edge-type = <IRQ_TYPE_EDGE_BOTH>; + dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(25))>; + dma-names = "rx"; + #io-channel-cells = <1>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/atmel,sama9260-adc.yaml b/Documentation/devicetree/bindings/iio/adc/atmel,sama9260-adc.yaml new file mode 100644 index 000000000000..e6a1f915b542 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/atmel,sama9260-adc.yaml @@ -0,0 +1,121 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/atmel,sama9260-adc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: AT91 sama9260 and similar Analog to Digital Converter (ADC) + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + +properties: + compatible: + enum: + - atmel,at91sam9260-adc + - atmel,at91sam9rl-adc + - atmel,at91sam9g45-adc + - atmel,at91sam9x5-adc + - atmel,at91sama5d3-adc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 2 + + clock-names: + items: + - const: adc_clk + - const: adc_op_clk + + atmel,adc-channels-used: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Bitmask of the channels muxed and enabled for this device + + atmel,adc-startup-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Startup Time of the ADC in microseconds as defined in the datasheet + + atmel,adc-vref: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Reference voltage in millivolts for the conversions + + atmel,adc-use-external-triggers: + $ref: /schemas/types.yaml#/definitions/flag + description: Enable the external triggers + + atmel,adc-use-res: + $ref: /schemas/types.yaml#/definitions/string + description: + String corresponding to an identifier from atmel,adc-res-names property. + If not specified, the highest resolution will be used. + enum: + - "lowres" + - "highres" + + atmel,adc-sleep-mode: + $ref: /schemas/types.yaml#/definitions/flag + description: Enable sleep mode when no conversion + + atmel,adc-sample-hold-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Sample and Hold Time in microseconds + + atmel,adc-ts-wires: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Number of touchscreen wires. Must be set to enable touchscreen. + NOTE: when adc touchscreen is enabled, the adc hardware trigger will be + disabled. Since touchscreen will occupy the trigger register. + enum: + - 4 + - 5 + + atmel,adc-ts-pressure-threshold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Pressure threshold for touchscreen. + + "#io-channel-cells": + const: 1 + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - atmel,adc-channels-used + - atmel,adc-startup-time + - atmel,adc-vref + +examples: + - | + #include <dt-bindings/dma/at91.h> + #include <dt-bindings/interrupt-controller/irq.h> + soc { + #address-cells = <1>; + #size-cells = <1>; + + adc@fffb0000 { + compatible = "atmel,at91sam9260-adc"; + reg = <0xfffb0000 0x100>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&adc_clk>, <&adc_op_clk>; + clock-names = "adc_clk", "adc_op_clk"; + atmel,adc-channels-used = <0xff>; + atmel,adc-startup-time = <40>; + atmel,adc-use-external-triggers; + atmel,adc-vref = <3300>; + atmel,adc-use-res = "lowres"; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/axp20x_adc.txt b/Documentation/devicetree/bindings/iio/adc/axp20x_adc.txt deleted file mode 100644 index 7a6313913923..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/axp20x_adc.txt +++ /dev/null @@ -1,48 +0,0 @@ -* X-Powers AXP ADC bindings - -Required properties: - - compatible: should be one of: - - "x-powers,axp209-adc", - - "x-powers,axp221-adc", - - "x-powers,axp813-adc", - - #io-channel-cells: should be 1, - -Example: - -&axp22x { - adc { - compatible = "x-powers,axp221-adc"; - #io-channel-cells = <1>; - }; -}; - -ADC channels and their indexes per variant: - -AXP209 ------- - 0 | acin_v - 1 | acin_i - 2 | vbus_v - 3 | vbus_i - 4 | pmic_temp - 5 | gpio0_v - 6 | gpio1_v - 7 | ipsout_v - 8 | batt_v - 9 | batt_chrg_i -10 | batt_dischrg_i - -AXP22x ------- - 0 | pmic_temp - 1 | batt_v - 2 | batt_chrg_i - 3 | batt_dischrg_i - -AXP813 ------- - 0 | pmic_temp - 1 | gpio0_v - 2 | batt_v - 3 | batt_chrg_i - 4 | batt_dischrg_i diff --git a/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt b/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt deleted file mode 100644 index 7b1b1e4086d4..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt +++ /dev/null @@ -1,40 +0,0 @@ -* Broadcom's IPROC Static ADC controller - -Broadcom iProc ADC controller has 8 channels 10bit ADC. -Allows user to convert analog input voltage values to digital. - -Required properties: - -- compatible: Must be "brcm,iproc-static-adc" - -- adc-syscon: Handler of syscon node defining physical base address of the - controller and length of memory mapped region. - -- #io-channel-cells = <1>; As ADC has multiple outputs - refer to Documentation/devicetree/bindings/iio/iio-bindings.txt for details. - -- io-channel-ranges: - refer to Documentation/devicetree/bindings/iio/iio-bindings.txt for details. - -- clocks: Clock used for this block. - -- clock-names: Clock name should be given as tsc_clk. - -- interrupts: interrupt line number. - -For example: - - ts_adc_syscon: ts_adc_syscon@180a6000 { - compatible = "brcm,iproc-ts-adc-syscon","syscon"; - reg = <0x180a6000 0xc30>; - }; - - adc: adc@180a6000 { - compatible = "brcm,iproc-static-adc"; - adc-syscon = <&ts_adc_syscon>; - #io-channel-cells = <1>; - io-channel-ranges; - clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>; - clock-names = "tsc_clk"; - interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.yaml b/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.yaml new file mode 100644 index 000000000000..c562d25bee3b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/brcm,iproc-static-adc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom's IPROC Static ADC controller + +maintainers: + - Raveendra Padasalagi <raveendra.padasalagi@broadcom.com> + +description: | + Broadcom iProc ADC controller has 8 10bit channels + +properties: + compatible: + const: brcm,iproc-static-adc + + adc-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: + syscon node defining physical base address of the controller and length + of memory mapped region. + + "#io-channel-cells": + const: 1 + + clocks: + maxItems: 1 + + clock-names: + const: tsc_clk + + interrupts: + maxItems: 1 + +additionalProperties: false + +required: + - compatible + - adc-syscon + - "#io-channel-cells" + - clocks + - clock-names + - interrupts + +examples: + - | + #include <dt-bindings/clock/bcm-cygnus.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + soc { + #address-cells = <1>; + #size-cells = <1>; + + ts_adc_syscon: ts_adc_syscon@180a6000 { + compatible = "brcm,iproc-ts-adc-syscon","syscon"; + reg = <0x180a6000 0xc30>; + }; + + adc { + compatible = "brcm,iproc-static-adc"; + adc-syscon = <&ts_adc_syscon>; + #io-channel-cells = <1>; + clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>; + clock-names = "tsc_clk"; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt b/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt deleted file mode 100644 index 27544bdd4478..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt +++ /dev/null @@ -1,54 +0,0 @@ -Bindings for ADC envelope detector using a DAC and a comparator - -The DAC is used to find the peak level of an alternating voltage input -signal by a binary search using the output of a comparator wired to -an interrupt pin. Like so: - _ - | \ - input +------>-------|+ \ - | \ - .-------. | }---. - | | | / | - | dac|-->--|- / | - | | |_/ | - | | | - | | | - | irq|------<-------' - | | - '-------' - -Required properties: -- compatible: Should be "axentia,tse850-envelope-detector" -- io-channels: Channel node of the dac to be used for comparator input. -- io-channel-names: Should be "dac". -- interrupt specification for one client interrupt, - see ../../interrupt-controller/interrupts.txt for details. -- interrupt-names: Should be "comp". - -Example: - - &i2c { - dpot: mcp4651-104@28 { - compatible = "microchip,mcp4651-104"; - reg = <0x28>; - #io-channel-cells = <1>; - }; - }; - - dac: dac { - compatible = "dpot-dac"; - vref-supply = <®_3v3>; - io-channels = <&dpot 0>; - io-channel-names = "dpot"; - #io-channel-cells = <1>; - }; - - envelope-detector { - compatible = "axentia,tse850-envelope-detector"; - io-channels = <&dac 0>; - io-channel-names = "dac"; - - interrupt-parent = <&gpio>; - interrupts = <3 IRQ_TYPE_EDGE_FALLING>; - interrupt-names = "comp"; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/envelope-detector.yaml b/Documentation/devicetree/bindings/iio/adc/envelope-detector.yaml new file mode 100644 index 000000000000..296d5459b40a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/envelope-detector.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/envelope-detector.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ADC envelope detector using a DAC and a comparator + +maintainers: + - Peter Rosin <peda@axentia.se> + +description: | + The DAC is used to find the peak level of an alternating voltage input + signal by a binary search using the output of a comparator wired to + an interrupt pin. Like so: + _ + | \ + input +------>-------|+ \ + | \ + .-------. | }---. + | | | / | + | dac|-->--|- / | + | | |_/ | + | | | + | | | + | irq|------<-------' + | | + '-------' + +properties: + compatible: + const: axentia,tse850-envelope-detector + + io-channels: + maxItems: 1 + description: Channel node of the dac to be used for comparator input. + + io-channel-names: + const: dac + + interrupts: + maxItems: 1 + + interrupt-names: + const: comp + +required: + - compatible + - io-channels + - io-channel-names + - interrupts + - interrupt-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + dpot: dpot@28 { + compatible = "microchip,mcp4651-104"; + reg = <0x28>; + #io-channel-cells = <1>; + }; + }; + + dac: dac { + compatible = "dpot-dac"; + vref-supply = <®_3v3>; + io-channels = <&dpot 0>; + io-channel-names = "dpot"; + #io-channel-cells = <1>; + }; + + envelope-detector { + compatible = "axentia,tse850-envelope-detector"; + io-channels = <&dac 0>; + io-channel-names = "dac"; + + interrupt-parent = <&gpio>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "comp"; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/maxim,max1027.yaml b/Documentation/devicetree/bindings/iio/adc/maxim,max1027.yaml new file mode 100644 index 000000000000..46b7747076b9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/maxim,max1027.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/maxim,max1027.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX1027 and similar ADCs + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + - Philippe Reynes <tremyfr@yahoo.fr> + +description: | + 300ks/s SPI ADCs with temperature sensors. + +properties: + compatible: + enum: + # 10-bit 8 channels + - maxim,max1027 + # 10-bit 12 channels + - maxim,max1029 + # 10-bit 16 channels + - maxim,max1031 + # 12-bit 8 channels + - maxim,max1227 + # 12-bit 12 channels + - maxim,max1229 + # 12-bit 16 channels + - maxim,max1231 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + spi-max-frequency: + maximum: 10000000 + + "#io-channel-cells": + const: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + maxadc: adc@0 { + compatible = "maxim,max1027"; + reg = <0>; + #io-channel-cells = <1>; + interrupt-parent = <&gpio5>; + interrupts = <15 IRQ_TYPE_EDGE_RISING>; + spi-max-frequency = <1000000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/mediatek,mt2701-auxadc.yaml b/Documentation/devicetree/bindings/iio/adc/mediatek,mt2701-auxadc.yaml new file mode 100644 index 000000000000..5b21a9fba5dd --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/mediatek,mt2701-auxadc.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/mediatek,mt2701-auxadc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek AUXADC - ADC on Mediatek mobile SoC (mt65xx/mt81xx/mt27xx) + +maintainers: + - Zhiyong Tao <zhiyong.tao@mediatek.com> + - Matthias Brugger <matthias.bgg@gmail.com> + +description: | + The Auxiliary Analog/Digital Converter (AUXADC) is an ADC found + in some Mediatek SoCs which among other things measures the temperatures + in the SoC. It can be used directly with register accesses, but it is also + used by thermal controller which reads the temperatures from the AUXADC + directly via its own bus interface. See mediatek-thermal bindings + for the Thermal Controller which holds a phandle to the AUXADC. + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt2701-auxadc + - mediatek,mt2712-auxadc + - mediatek,mt6765-auxadc + - mediatek,mt7622-auxadc + - mediatek,mt8173-auxadc + - items: + - enum: + - mediatek,mt7623-auxadc + - const: mediatek,mt2701-auxadc + - items: + - enum: + - mediatek,mt8183-auxadc + - mediatek,mt8516-auxadc + - const: mediatek,mt8173-auxadc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: main + + "#io-channel-cells": + const: 1 + +additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - "#io-channel-cells" + +examples: + - | + #include <dt-bindings/clock/mt8183-clk.h> + soc { + #address-cells = <2>; + #size-cells = <2>; + + adc@11001000 { + compatible = "mediatek,mt8183-auxadc", + "mediatek,mt8173-auxadc"; + reg = <0 0x11001000 0 0x1000>; + clocks = <&infracfg CLK_INFRA_AUXADC>; + clock-names = "main"; + #io-channel-cells = <1>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/mediatek,mt6360-adc.yaml b/Documentation/devicetree/bindings/iio/adc/mediatek,mt6360-adc.yaml new file mode 100644 index 000000000000..db4e3613c104 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/mediatek,mt6360-adc.yaml @@ -0,0 +1,31 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/mediatek,mt6360-adc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT6360 and similar ADCs + +maintainers: + - Gene Chen <gene_chen@richtek.com> + +properties: + compatible: + const: mediatek,mt6360-adc + + "#io-channel-cells": + const: 1 + +required: + - compatible + - "#io-channel-cells" + +additionalProperties: false + +examples: + - | + adc { + compatible = "mediatek,mt6360-adc"; + #io-channel-cells = <1>; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt deleted file mode 100644 index 78c06e05c8e5..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt +++ /dev/null @@ -1,33 +0,0 @@ -* Mediatek AUXADC - Analog to Digital Converter on Mediatek mobile soc (mt65xx/mt81xx/mt27xx) -=============== - -The Auxiliary Analog/Digital Converter (AUXADC) is an ADC found -in some Mediatek SoCs which among other things measures the temperatures -in the SoC. It can be used directly with register accesses, but it is also -used by thermal controller which reads the temperatures from the AUXADC -directly via its own bus interface. See -Documentation/devicetree/bindings/thermal/mediatek-thermal.txt -for the Thermal Controller which holds a phandle to the AUXADC. - -Required properties: - - compatible: Should be one of: - - "mediatek,mt2701-auxadc": For MT2701 family of SoCs - - "mediatek,mt2712-auxadc": For MT2712 family of SoCs - - "mediatek,mt6765-auxadc": For MT6765 family of SoCs - - "mediatek,mt7622-auxadc": For MT7622 family of SoCs - - "mediatek,mt8173-auxadc": For MT8173 family of SoCs - - "mediatek,mt8183-auxadc", "mediatek,mt8173-auxadc": For MT8183 family of SoCs - - reg: Address range of the AUXADC unit. - - clocks: Should contain a clock specifier for each entry in clock-names - - clock-names: Should contain "main". - - #io-channel-cells: Should be 1, see ../iio-bindings.txt - -Example: - -auxadc: adc@11001000 { - compatible = "mediatek,mt2701-auxadc"; - reg = <0 0x11001000 0 0x1000>; - clocks = <&pericfg CLK_PERI_AUXADC>; - clock-names = "main"; - #io-channel-cells = <1>; -}; diff --git a/Documentation/devicetree/bindings/iio/adc/palmas-gpadc.txt b/Documentation/devicetree/bindings/iio/adc/palmas-gpadc.txt deleted file mode 100644 index 4bb9a86065d1..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/palmas-gpadc.txt +++ /dev/null @@ -1,48 +0,0 @@ -* Palmas general purpose ADC IP block devicetree bindings - -Channels list: - 0 battery type - 1 battery temp NTC (optional current source) - 2 GP - 3 temp (with ext. diode, optional current source) - 4 GP - 5 GP - 6 VBAT_SENSE - 7 VCC_SENSE - 8 Backup Battery voltage - 9 external charger (VCHG) - 10 VBUS - 11 DC-DC current probe (how does this work?) - 12 internal die temp - 13 internal die temp - 14 USB ID pin voltage - 15 test network - -Required properties: -- compatible : Must be "ti,palmas-gpadc". -- #io-channel-cells: Should be set to <1>. - -Optional sub-nodes: -ti,channel0-current-microamp: Channel 0 current in uA. - Values are rounded to derive 0uA, 5uA, 15uA, 20uA. -ti,channel3-current-microamp: Channel 3 current in uA. - Values are rounded to derive 0uA, 10uA, 400uA, 800uA. -ti,enable-extended-delay: Enable extended delay. - -Example: - -pmic { - compatible = "ti,twl6035-pmic", "ti,palmas-pmic"; - ... - gpadc { - compatible = "ti,palmas-gpadc"; - interrupts = <18 0 - 16 0 - 17 0>; - #io-channel-cells = <1>; - ti,channel0-current-microamp = <5>; - ti,channel3-current-microamp = <10>; - }; - }; - ... -}; diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,pm8018-adc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,pm8018-adc.yaml new file mode 100644 index 000000000000..d186b713d6a7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/qcom,pm8018-adc.yaml @@ -0,0 +1,166 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/qcom,pm8018-adc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm's PM8xxx voltage XOADC + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + The Qualcomm PM8xxx PMICs contain a HK/XO ADC (Housekeeping/Crystal + oscillator ADC) encompassing PM8018, PM8038, PM8058 and PM8921. + +properties: + compatible: + enum: + - qcom,pm8018-adc + - qcom,pm8038-adc + - qcom,pm8058-adc + - qcom,pm8921-adc + + reg: + maxItems: 1 + description: + ADC base address in the PMIC, typically 0x197. + + xoadc-ref-supply: + description: + The reference voltage may vary with PMIC variant but is typically + something like 2.2 or 1.8V. + + interrupts: + maxItems: 1 + + "#address-cells": + const: 2 + description: + The first cell is the prescaler (on PM8058) or premux (on PM8921) + with two valid bits so legal values are 0x00, 0x01 or 0x02. + The second cell is the main analog mux setting (0x00..0x0f). + The combination of prescaler/premux and analog mux uniquely addresses + a hardware channel on all systems. + + "#size-cells": + const: 0 + + "#io-channel-cells": + const: 2 + description: + The cells are precaler or premux followed by the analog muxing line. + +additionalProperties: false + +required: + - compatible + - reg + - "#io-channel-cells" + - "#address-cells" + - "#size-cells" + - adc-channel@c + - adc-channel@d + - adc-channel@f + +patternProperties: + "^(adc-channel@)[0-9a-f]$": + type: object + description: | + ADC channel specific configuration. + Note that channels c, d and f must be present for calibration. + These three nodes are used for absolute and ratiometric calibration + and only need to have these reg values: they are by hardware definition + 1:1 ratio converters that sample 625, 1250 and 0 milliV and create + an interpolation calibration for all other ADCs. + + properties: + reg: + maxItems: 1 + + qcom,decimation: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + This parameter is used to decrease the ADC sampling rate. + Quicker measurements can be made by reducing the decimation ratio. + Valid values are 512, 1024, 2048, 4096. + If the property is not found, a default value of 512 will be used. + + qcom,ratiometric: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Channel calibration type. If this property is specified + VADC will use a special voltage references for channel + calibration. The available references are specified in the + as a u32 value setting (see below) and it is compulsory + to also specify this reference if ratiometric calibration + is selected. + + If the property is not found, the channel will be + calibrated with the 0.625V and 1.25V reference channels, also + known as an absolute calibration. + + The reference voltage pairs when using ratiometric calibration: + 0 = XO_IN/XOADC_GND + 1 = PMIC_IN/XOADC_GND + 2 = PMIC_IN/BMS_CSP + 3 (invalid) + 4 = XOADC_GND/XOADC_GND + 5 = XOADC_VREF/XOADC_GND + + additionalProperties: false + + required: + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + pmic { + #address-cells = <1>; + #size-cells = <0>; + + adc@197 { + compatible = "qcom,pm8058-adc"; + reg = <0x197>; + interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>; + #address-cells = <2>; + #size-cells = <0>; + #io-channel-cells = <2>; + + vcoin: adc-channel@0 { + reg = <0x00 0x00>; + }; + vbat: adc-channel@1 { + reg = <0x00 0x01>; + }; + dcin: adc-channel@2 { + reg = <0x00 0x02>; + }; + ichg: adc-channel@3 { + reg = <0x00 0x03>; + }; + vph_pwr: adc-channel@4 { + reg = <0x00 0x04>; + }; + usb_vbus: adc-channel@a { + reg = <0x00 0x0a>; + }; + die_temp: adc-channel@b { + reg = <0x00 0x0b>; + }; + ref_625mv: adc-channel@c { + reg = <0x00 0x0c>; + }; + ref_1250mv: adc-channel@d { + reg = <0x00 0x0d>; + }; + ref_325mv: adc-channel@e { + reg = <0x00 0x0e>; + }; + ref_muxoff: adc-channel@f { + reg = <0x00 0x0f>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt deleted file mode 100644 index 3ae06127789e..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt +++ /dev/null @@ -1,157 +0,0 @@ -Qualcomm's PM8xxx voltage XOADC - -The Qualcomm PM8xxx PMICs contain a HK/XO ADC (Housekeeping/Crystal -oscillator ADC) encompassing PM8018, PM8038, PM8058 and PM8921. - -Required properties: - -- compatible: should be one of: - "qcom,pm8018-adc" - "qcom,pm8038-adc" - "qcom,pm8058-adc" - "qcom,pm8921-adc" - -- reg: should contain the ADC base address in the PMIC, typically - 0x197. - -- xoadc-ref-supply: should reference a regulator that can supply - a reference voltage on demand. The reference voltage may vary - with PMIC variant but is typically something like 2.2 or 1.8V. - -The following required properties are standard for IO channels, see -iio-bindings.txt for more details, but notice that this particular -ADC has a special addressing scheme that require two cells for -identifying each ADC channel: - -- #address-cells: should be set to <2>, the first cell is the - prescaler (on PM8058) or premux (on PM8921) with two valid bits - so legal values are 0x00, 0x01 or 0x02. The second cell - is the main analog mux setting (0x00..0x0f). The combination - of prescaler/premux and analog mux uniquely addresses a hardware - channel on all systems. - -- #size-cells: should be set to <0> - -- #io-channel-cells: should be set to <2>, again the cells are - precaler or premux followed by the analog muxing line. - -- interrupts: should refer to the parent PMIC interrupt controller - and reference the proper ADC interrupt. - -Required subnodes: - -The ADC channels are configured as subnodes of the ADC. - -Since some of them are used for calibrating the ADC, these nodes are -compulsory: - -adc-channel@c { - reg = <0x00 0x0c>; -}; - -adc-channel@d { - reg = <0x00 0x0d>; -}; - -adc-channel@f { - reg = <0x00 0x0f>; -}; - -These three nodes are used for absolute and ratiometric calibration -and only need to have these reg values: they are by hardware definition -1:1 ratio converters that sample 625, 1250 and 0 milliV and create -an interpolation calibration for all other ADCs. - -Optional subnodes: any channels other than channels [0x00 0x0c], -[0x00 0x0d] and [0x00 0x0f] are optional. - -Required channel node properties: - -- reg: should contain the hardware channel number in the range - 0 .. 0xff (8 bits). - -Optional channel node properties: - -- qcom,decimation: - Value type: <u32> - Definition: This parameter is used to decrease the ADC sampling rate. - Quicker measurements can be made by reducing the decimation ratio. - Valid values are 512, 1024, 2048, 4096. - If the property is not found, a default value of 512 will be used. - -- qcom,ratiometric: - Value type: <u32> - Definition: Channel calibration type. If this property is specified - VADC will use a special voltage references for channel - calibration. The available references are specified in the - as a u32 value setting (see below) and it is compulsory - to also specify this reference if ratiometric calibration - is selected. - - If the property is not found, the channel will be - calibrated with the 0.625V and 1.25V reference channels, also - known as an absolute calibration. - The reference voltage pairs when using ratiometric calibration: - 0 = XO_IN/XOADC_GND - 1 = PMIC_IN/XOADC_GND - 2 = PMIC_IN/BMS_CSP - 3 (invalid) - 4 = XOADC_GND/XOADC_GND - 5 = XOADC_VREF/XOADC_GND - -Example: - -xoadc: xoadc@197 { - compatible = "qcom,pm8058-adc"; - reg = <0x197>; - interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>; - #address-cells = <2>; - #size-cells = <0>; - #io-channel-cells = <2>; - - vcoin: adc-channel@0 { - reg = <0x00 0x00>; - }; - vbat: adc-channel@1 { - reg = <0x00 0x01>; - }; - dcin: adc-channel@2 { - reg = <0x00 0x02>; - }; - ichg: adc-channel@3 { - reg = <0x00 0x03>; - }; - vph_pwr: adc-channel@4 { - reg = <0x00 0x04>; - }; - usb_vbus: adc-channel@a { - reg = <0x00 0x0a>; - }; - die_temp: adc-channel@b { - reg = <0x00 0x0b>; - }; - ref_625mv: adc-channel@c { - reg = <0x00 0x0c>; - }; - ref_1250mv: adc-channel@d { - reg = <0x00 0x0d>; - }; - ref_325mv: adc-channel@e { - reg = <0x00 0x0e>; - }; - ref_muxoff: adc-channel@f { - reg = <0x00 0x0f>; - }; -}; - -/* IIO client node */ -iio-hwmon { - compatible = "iio-hwmon"; - io-channels = <&xoadc 0x00 0x01>, /* Battery */ - <&xoadc 0x00 0x02>, /* DC in (charger) */ - <&xoadc 0x00 0x04>, /* VPH the main system voltage */ - <&xoadc 0x00 0x0b>, /* Die temperature */ - <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */ - <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */ - <&xoadc 0x00 0x0e>; /* Reference voltage 0.325V */ -}; diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt deleted file mode 100644 index 4e36d6e2f7b6..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt +++ /dev/null @@ -1,46 +0,0 @@ -Qualcomm's SPMI PMIC current ADC - -QPNP PMIC current ADC (IADC) provides interface to clients to read current. -A 16 bit ADC is used for current measurements. IADC can measure the current -through an external resistor (channel 1) or internal (built-in) resistor -(channel 0). When using an external resistor it is to be described by -qcom,external-resistor-micro-ohms property. - -IADC node: - -- compatible: - Usage: required - Value type: <string> - Definition: Should contain "qcom,spmi-iadc". - -- reg: - Usage: required - Value type: <prop-encoded-array> - Definition: IADC base address and length in the SPMI PMIC register map - -- interrupts: - Usage: optional - Value type: <prop-encoded-array> - Definition: End of ADC conversion. - -- qcom,external-resistor-micro-ohms: - Usage: optional - Value type: <u32> - Definition: Sense resister value in micro Ohm. - If not defined value of 10000 micro Ohms will be used. - -Example: - /* IADC node */ - pmic_iadc: iadc@3600 { - compatible = "qcom,spmi-iadc"; - reg = <0x3600 0x100>; - interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; - qcom,external-resistor-micro-ohms = <10000>; - #io-channel-cells = <1>; - }; - - /* IIO client node */ - bat { - io-channels = <&pmic_iadc 0>; - io-channel-names = "iadc"; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.yaml new file mode 100644 index 000000000000..27e3108661c0 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/qcom,spmi-iadc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm's SPMI PMIC current ADC + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: | + QPNP PMIC current ADC (IADC) provides interface to clients to read current. + A 16 bit ADC is used for current measurements. IADC can measure the current + through an external resistor (channel 1) or internal (built-in) resistor + (channel 0). When using an external resistor it is to be described by + qcom,external-resistor-micro-ohms property. + +properties: + compatible: + const: qcom,spmi-iadc + + reg: + description: IADC base address and length in the SPMI PMIC register map + maxItems: 1 + + qcom,external-resistor-micro-ohms: + description: + Sensor resistor value. If not defined value of 10000 micro Ohms + will be used. + + interrupts: + maxItems: 1 + description: + End of conversion interrupt. + + "#io-channel-cells": + const: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + spmi_bus { + #address-cells = <1>; + #size-cells = <0>; + pmic_iadc: adc@3600 { + compatible = "qcom,spmi-iadc"; + reg = <0x3600 0x100>; + interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; + qcom,external-resistor-micro-ohms = <10000>; + #io-channel-cells = <1>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml index 7f4f827c57a7..95cc705b961b 100644 --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml @@ -48,8 +48,6 @@ properties: description: End of conversion interrupt. - io-channel-ranges: true - required: - compatible - reg @@ -249,7 +247,6 @@ examples: #address-cells = <1>; #size-cells = <0>; #io-channel-cells = <1>; - io-channel-ranges; /* Channel node */ adc-chan@39 { diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt deleted file mode 100644 index df5b9f2ad8d8..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt +++ /dev/null @@ -1,98 +0,0 @@ -* Renesas R-Car GyroADC device driver - -The GyroADC block is a reduced SPI block with up to 8 chipselect lines, -which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs -are sampled by the GyroADC block in a round-robin fashion and the result -presented in the GyroADC registers. - -Required properties: -- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc". - The <soc-specific> should be one of: - renesas,r8a7791-gyroadc - for the GyroADC block present - in r8a7791 SoC - renesas,r8a7792-gyroadc - for the GyroADC with interrupt - block present in r8a7792 SoC -- reg: Address and length of the register set for the device -- clocks: References to all the clocks specified in the clock-names - property as specified in - Documentation/devicetree/bindings/clock/clock-bindings.txt. -- clock-names: Shall contain "fck". The "fck" is the GyroADC block clock. -- power-domains: Must contain a reference to the PM domain, if available. -- #address-cells: Should be <1> (setting for the subnodes) for all ADCs - except for "fujitsu,mb88101a". Should be <0> (setting for - only subnode) for "fujitsu,mb88101a". -- #size-cells: Should be <0> (setting for the subnodes) - -Sub-nodes: -You must define subnode(s) which select the connected ADC type and reference -voltage for the GyroADC channels. - -Required properties for subnodes: -- compatible: Should be either of: - "fujitsu,mb88101a" - - Fujitsu MB88101A compatible mode, - 12bit sampling, up to 4 channels can be sampled in - round-robin fashion. One Fujitsu chip supplies four - GyroADC channels with data as it contains four ADCs - on the chip and thus for 4-channel operation, single - MB88101A is required. The Cx chipselect lines of the - MB88101A connect directly to two CHS lines of the - GyroADC, no demuxer is required. The data out line - of each MB88101A connects to a shared input pin of - the GyroADC. - "ti,adcs7476" or "ti,adc121" or "adi,ad7476" - - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, - 15bit sampling, up to 8 channels can be sampled in - round-robin fashion. One TI/ADI chip supplies single - ADC channel with data, thus for 8-channel operation, - 8 chips are required. A 3:8 chipselect demuxer is - required to connect the nCS line of the TI/ADI chips - to the GyroADC, while MISO line of each TI/ADI ADC - connects to a shared input pin of the GyroADC. - "maxim,max1162" or "maxim,max11100" - - Maxim MAX1162 / Maxim MAX11100 compatible mode, - 16bit sampling, up to 8 channels can be sampled in - round-robin fashion. One Maxim chip supplies single - ADC channel with data, thus for 8-channel operation, - 8 chips are required. A 3:8 chipselect demuxer is - required to connect the nCS line of the MAX chips - to the GyroADC, while MISO line of each Maxim ADC - connects to a shared input pin of the GyroADC. -- reg: Should be the number of the analog input. Should be present - for all ADCs except "fujitsu,mb88101a". -- vref-supply: Reference to the channel reference voltage regulator. - -Example: - vref_max1162: regulator-vref-max1162 { - compatible = "regulator-fixed"; - - regulator-name = "MAX1162 Vref"; - regulator-min-microvolt = <4096000>; - regulator-max-microvolt = <4096000>; - }; - - adc@e6e54000 { - compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; - reg = <0 0xe6e54000 0 64>; - clocks = <&mstp9_clks R8A7791_CLK_GYROADC>; - clock-names = "fck"; - power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; - - pinctrl-0 = <&adc_pins>; - pinctrl-names = "default"; - - #address-cells = <1>; - #size-cells = <0>; - - adc@0 { - reg = <0>; - compatible = "maxim,max1162"; - vref-supply = <&vref_max1162>; - }; - - adc@1 { - reg = <1>; - compatible = "maxim,max1162"; - vref-supply = <&vref_max1162>; - }; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,rcar-gyroadc.yaml b/Documentation/devicetree/bindings/iio/adc/renesas,rcar-gyroadc.yaml new file mode 100644 index 000000000000..c115e2e99bd9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/renesas,rcar-gyroadc.yaml @@ -0,0 +1,143 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/renesas,rcar-gyroadc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car GyroADC + +maintainers: + - Marek Vasut <marek.vasut+renesas@gmail.com> + +description: | + The GyroADC block is a reduced SPI block with up to 8 chipselect lines, + which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs + are sampled by the GyroADC block in a round-robin fashion and the result + presented in the GyroADC registers. + The ADC bindings should match with that of the devices connected to a + full featured SPI bus. + +properties: + compatible: + items: + - enum: + - renesas,r8a7791-gyroadc + - renesas,r8a7792-gyroadc + - const: renesas,rcar-gyroadc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: fck + + power-domains: true + + resets: true + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - "#address-cells" + - "#size-cells" + +patternProperties: + "@[0-7]$": + type: object + properties: + compatible: + description: | + fujitsu,mb88101a + - Fujitsu MB88101A compatible mode, + 12bit sampling, up to 4 channels can be sampled in round-robin + fashion. One Fujitsu chip supplies four GyroADC channels with + data as it contains four ADCs on the chip and thus for 4-channel + operation, single MB88101A is required. The Cx chipselect lines + of the MB88101A connect directly to two CHS lines of the GyroADC, + no demuxer is required. The data out line of each MB88101A + connects to a shared input pin of the GyroADC. + ti,adcs7476 or ti,adc121 or adi,ad7476 + - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, 15bit + sampling, up to 8 channels can be sampled in round-robin + fashion. One TI/ADI chip supplies single ADC channel with data, + thus for 8-channel operation, 8 chips are required. + A 3:8 chipselect demuxer is required to connect the nCS line + of the TI/ADI chips to the GyroADC, while MISO line of each + TI/ADI ADC connects to a shared input pin of the GyroADC. + maxim,max1162 or maxim,max11100 + - Maxim MAX1162 / Maxim MAX11100 compatible mode, 16bit sampling, + up to 8 channels can be sampled in round-robin fashion. One + Maxim chip supplies single ADC channel with data, thus for + 8-channel operation, 8 chips are required. + A 3:8 chipselect demuxer is required to connect the nCS line + of the MAX chips to the GyroADC, while MISO line of each Maxim + ADC connects to a shared input pin of the GyroADC. + enum: + - adi,7476 + - fujitsu,mb88101a + - maxim,max1162 + - maxim,max11100 + - ti,adcs7476 + - ti,adc121 + + reg: + minimum: 0 + maximum: 7 + + vref-supply: true + + additionalProperties: false + + required: + - compatible + - reg + - vref-supply + +examples: + - | + #include <dt-bindings/clock/r8a7791-clock.h> + #include <dt-bindings/power/r8a7791-sysc.h> + soc { + #address-cells = <2>; + #size-cells = <2>; + + adc@e6e54000 { + compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; + reg = <0 0xe6e54000 0 64>; + clocks = <&mstp9_clks R8A7791_CLK_GYROADC>; + clock-names = "fck"; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + + pinctrl-0 = <&adc_pins>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + reg = <0>; + compatible = "maxim,max1162"; + vref-supply = <&vref_max1162>; + }; + + adc@1 { + reg = <1>; + compatible = "maxim,max1162"; + vref-supply = <&vref_max1162>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.yaml b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.yaml index 5ebb0ab250bd..c65921e66dc1 100644 --- a/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.yaml +++ b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.yaml @@ -49,8 +49,6 @@ properties: "#io-channel-cells": const: 1 - io-channel-ranges: true - vdd-supply: true samsung,syscon-phandle: @@ -130,7 +128,6 @@ examples: reg = <0x12d10000 0x100>; interrupts = <0 106 0>; #io-channel-cells = <1>; - io-channel-ranges; clocks = <&clock 303>; clock-names = "adc"; @@ -156,7 +153,6 @@ examples: reg = <0x126C0000 0x100>; interrupts = <0 137 0>; #io-channel-cells = <1>; - io-channel-ranges; clocks = <&cmu CLK_TSADC>, <&cmu CLK_SCLK_TSADC>; diff --git a/Documentation/devicetree/bindings/iio/adc/ti,adc084s021.yaml b/Documentation/devicetree/bindings/iio/adc/ti,adc084s021.yaml new file mode 100644 index 000000000000..1a113b30a414 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti,adc084s021.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/ti,adc084s021.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments ADC084S021 ADC + +maintainers: + - Mårten Lindahl <martenli@axis.com> + +description: | + 8 bit ADC with 4 channels + +properties: + compatible: + const: ti,adc084s021 + + reg: + maxItems: 1 + + spi-max-frequency: true + + vref-supply: + description: External reference, needed to establish input scaling + + spi-cpol: true + spi-cpha: true + + "#io-channel-cells": + const: 1 + +required: + - compatible + - reg + - vref-supply + - spi-cpol + - spi-cpha + +additionalProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "ti,adc084s021"; + reg = <0>; + vref-supply = <&adc_vref>; + spi-cpol; + spi-cpha; + spi-max-frequency = <16000000>; + #io-channel-cells = <1>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/ti,ads124s08.yaml b/Documentation/devicetree/bindings/iio/adc/ti,ads124s08.yaml new file mode 100644 index 000000000000..9f5e96439c01 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti,ads124s08.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/ti,ads124s08.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments' ads124s08 and ads124s06 ADC chip + +maintainers: + - Dan Murphy <dmurphy@ti.com> + +properties: + compatible: + enum: + - ti,ads124s06 + - ti,ads124s08 + + reg: + maxItems: 1 + + spi-max-frequency: true + + spi-cpha: true + + reset-gpios: + maxItems: 1 + + "#io-channel-cells": + const: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "ti,ads124s08"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpha; + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/ti,palmas-gpadc.yaml b/Documentation/devicetree/bindings/iio/adc/ti,palmas-gpadc.yaml new file mode 100644 index 000000000000..692dacd0fee5 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti,palmas-gpadc.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/ti,palmas-gpadc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Palmas general purpose ADC IP block devicetree bindings + +maintainers: + - Tony Lindgren <tony@atomide.com> + +description: | + This ADC is often used to provide channels via the io-channels + consumer framework. + Channels list: + 0 battery type + 1 battery temp NTC (optional current source) + 2 GP + 3 temp (with ext. diode, optional current source) + 4 GP + 5 GP + 6 VBAT_SENSE + 7 VCC_SENSE + 8 Backup Battery voltage + 9 external charger (VCHG) + 10 VBUS + 11 DC-DC current probe (how does this work?) + 12 internal die temp + 13 internal die temp + 14 USB ID pin voltage + 15 test network + +properties: + compatible: + const: ti,palmas-gpadc + + interrupts: + minItems: 1 + maxItems: 3 + + "#io-channel-cells": + const: 1 + + ti,channel0-current-microamp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Channel 0 current in uA. + enum: + - 0 + - 5 + - 15 + - 20 + + ti,channel3-current-microamp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Channel 3 current in uA. + enum: + - 0 + - 10 + - 400 + - 800 + + ti,enable-extended-delay: + $ref: /schemas/types.yaml#/definitions/flag + description: Enable extended delay. + +additionalProperties: false + +required: + - compatible + - "#io-channel-cells" + +examples: + - | + #include <dt-bindings/clock/mt8183-clk.h> + pmic { + compatible = "ti,twl6035-pmic", "ti,palmas-pmic"; + adc { + compatible = "ti,palmas-gpadc"; + interrupts = <18 0 + 16 0 + 17 0>; + #io-channel-cells = <1>; + ti,channel0-current-microamp = <5>; + ti,channel3-current-microamp = <10>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc084s021.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc084s021.txt deleted file mode 100644 index 4259e50620bc..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/ti-adc084s021.txt +++ /dev/null @@ -1,19 +0,0 @@ -* Texas Instruments' ADC084S021 - -Required properties: - - compatible : Must be "ti,adc084s021" - - reg : SPI chip select number for the device - - vref-supply : The regulator supply for ADC reference voltage - - spi-cpol : Per spi-bus bindings - - spi-cpha : Per spi-bus bindings - - spi-max-frequency : Per spi-bus bindings - -Example: -adc@0 { - compatible = "ti,adc084s021"; - reg = <0>; - vref-supply = <&adc_vref>; - spi-cpol; - spi-cpha; - spi-max-frequency = <16000000>; -}; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt b/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt deleted file mode 100644 index ecf807bb32f7..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt +++ /dev/null @@ -1,25 +0,0 @@ -* Texas Instruments' ads124s08 and ads124s06 ADC chip - -Required properties: - - compatible : - "ti,ads124s08" - "ti,ads124s06" - - reg : spi chip select number for the device - -Recommended properties: - - spi-max-frequency : Definition as per - Documentation/devicetree/bindings/spi/spi-bus.txt - - spi-cpha : Definition as per - Documentation/devicetree/bindings/spi/spi-bus.txt - -Optional properties: - - reset-gpios : GPIO pin used to reset the device. - -Example: -adc@0 { - compatible = "ti,ads124s08"; - reg = <0>; - spi-max-frequency = <1000000>; - spi-cpha; - reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; -}; diff --git a/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml b/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml new file mode 100644 index 000000000000..5ccbb1f81960 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/x-powers,axp209-adc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: X-Powers AXP ADC bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + +description: | + ADC is frequently used as a provider to consumers of the ADC channels. + Device is a child of an axp209 multifunction device + ADC channels and their indexes per variant: + + AXP209 + ------ + 0 | acin_v + 1 | acin_i + 2 | vbus_v + 3 | vbus_i + 4 | pmic_temp + 5 | gpio0_v + 6 | gpio1_v + 7 | ipsout_v + 8 | batt_v + 9 | batt_chrg_i + 10 | batt_dischrg_i + + AXP22x + ------ + 0 | pmic_temp + 1 | batt_v + 2 | batt_chrg_i + 3 | batt_dischrg_i + + AXP813 + ------ + 0 | pmic_temp + 1 | gpio0_v + 2 | batt_v + 3 | batt_chrg_i + 4 | batt_dischrg_i + + +properties: + compatible: + enum: + - x-powers,axp209-adc + - x-powers,axp221-adc + - x-powers,axp813-adc + + "#io-channel-cells": + const: 1 + +additionalProperties: false + +examples: + - | + axp221 { + adc { + compatible = "x-powers,axp221-adc"; + #io-channel-cells = <1>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.txt b/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.txt deleted file mode 100644 index 821b61b8c542..000000000000 --- a/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.txt +++ /dev/null @@ -1,26 +0,0 @@ -Current Sense Amplifier -======================= - -When an io-channel measures the output voltage from a current sense -amplifier, the interesting measurement is almost always the current -through the sense resistor, not the voltage output. This binding -describes such a current sense circuit. - -Required properties: -- compatible : "current-sense-amplifier" -- io-channels : Channel node of a voltage io-channel. -- sense-resistor-micro-ohms : The sense resistance in microohms. - -Optional properties: -- sense-gain-mult: Amplifier gain multiplier. The default is <1>. -- sense-gain-div: Amplifier gain divider. The default is <1>. - -Example: - -sysi { - compatible = "current-sense-amplifier"; - io-channels = <&tiadc 0>; - - sense-resistor-micro-ohms = <20000>; - sense-gain-mul = <50>; -}; diff --git a/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.yaml b/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.yaml new file mode 100644 index 000000000000..527501c1d695 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/afe/current-sense-amplifier.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Current Sense Amplifier + +maintainers: + - Peter Rosin <peda@axentia.se> + +description: | + When an io-channel measures the output voltage from a current sense + amplifier, the interesting measurement is almost always the current + through the sense resistor, not the voltage output. This binding + describes such a current sense circuit. + +properties: + compatible: + const: current-sense-amplifier + + io-channels: + maxItems: 1 + description: | + Channel node of a voltage io-channel. + + sense-resistor-micro-ohms: + description: The sense resistance. + + sense-gain-mult: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Amplifier gain multiplier. The default is <1>. + + sense-gain-div: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Amplifier gain divider. The default is <1>. + +required: + - compatible + - io-channels + - sense-resistor-micro-ohms + +additionalProperties: false + +examples: + - | + sysi { + compatible = "current-sense-amplifier"; + io-channels = <&tiadc 0>; + + sense-resistor-micro-ohms = <20000>; + sense-gain-mult = <50>; + }; +... diff --git a/Documentation/devicetree/bindings/iio/afe/current-sense-shunt.txt b/Documentation/devicetree/bindings/iio/afe/current-sense-shunt.txt deleted file mode 100644 index 0f67108a07b6..000000000000 --- a/Documentation/devicetree/bindings/iio/afe/current-sense-shunt.txt +++ /dev/null @@ -1,41 +0,0 @@ -Current Sense Shunt -=================== - -When an io-channel measures the voltage over a current sense shunt, -the interesting measurement is almost always the current through the -shunt, not the voltage over it. This binding describes such a current -sense circuit. - -Required properties: -- compatible : "current-sense-shunt" -- io-channels : Channel node of a voltage io-channel. -- shunt-resistor-micro-ohms : The shunt resistance in microohms. - -Example: -The system current is measured by measuring the voltage over a -3.3 ohms shunt resistor. - -sysi { - compatible = "current-sense-shunt"; - io-channels = <&tiadc 0>; - - /* Divide the voltage by 3300000/1000000 (or 3.3) for the current. */ - shunt-resistor-micro-ohms = <3300000>; -}; - -&i2c { - tiadc: adc@48 { - compatible = "ti,ads1015"; - reg = <0x48>; - #io-channel-cells = <1>; - - #address-cells = <1>; - #size-cells = <0>; - - channel@0 { /* IN0,IN1 differential */ - reg = <0>; - ti,gain = <1>; - ti,datarate = <4>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/iio/afe/current-sense-shunt.yaml b/Documentation/devicetree/bindings/iio/afe/current-sense-shunt.yaml new file mode 100644 index 000000000000..90439a8dc785 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/afe/current-sense-shunt.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/afe/current-sense-shunt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Current Sense Shunt + +maintainers: + - Peter Rosin <peda@axentia.se> + +description: | + When an io-channel measures the voltage over a current sense shunt, + the interesting measurement is almost always the current through the + shunt, not the voltage over it. This binding describes such a current + sense circuit. + +properties: + compatible: + const: current-sense-shunt + + io-channels: + maxItems: 1 + description: | + Channel node of a voltage io-channel. + + shunt-resistor-micro-ohms: + description: The shunt resistance. + +required: + - compatible + - io-channels + - shunt-resistor-micro-ohms + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + tiadc: adc@48 { + compatible = "ti,ads1015"; + reg = <0x48>; + #io-channel-cells = <1>; + + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { /* IN0,IN1 differential */ + reg = <0>; + ti,gain = <1>; + ti,datarate = <4>; + }; + }; + }; + sysi { + compatible = "current-sense-shunt"; + io-channels = <&tiadc 0>; + + /* Divide the voltage by 3300000/1000000 (or 3.3) for the current. */ + shunt-resistor-micro-ohms = <3300000>; + }; +... diff --git a/Documentation/devicetree/bindings/iio/afe/voltage-divider.txt b/Documentation/devicetree/bindings/iio/afe/voltage-divider.txt deleted file mode 100644 index b452a8406107..000000000000 --- a/Documentation/devicetree/bindings/iio/afe/voltage-divider.txt +++ /dev/null @@ -1,53 +0,0 @@ -Voltage divider -=============== - -When an io-channel measures the midpoint of a voltage divider, the -interesting voltage is often the voltage over the full resistance -of the divider. This binding describes the voltage divider in such -a curcuit. - - Vin ----. - | - .-----. - | R | - '-----' - | - +---- Vout - | - .-----. - | Rout| - '-----' - | - GND - -Required properties: -- compatible : "voltage-divider" -- io-channels : Channel node of a voltage io-channel measuring Vout. -- output-ohms : Resistance Rout over which the output voltage is measured. - See full-ohms. -- full-ohms : Resistance R + Rout for the full divider. The io-channel - is scaled by the Rout / (R + Rout) quotient. - -Example: -The system voltage is circa 12V, but divided down with a 22/222 -voltage divider (R = 200 Ohms, Rout = 22 Ohms) and fed to an ADC. - -sysv { - compatible = "voltage-divider"; - io-channels = <&maxadc 1>; - - /* Scale the system voltage by 22/222 to fit the ADC range. */ - output-ohms = <22>; - full-ohms = <222>; /* 200 + 22 */ -}; - -&spi { - maxadc: adc@0 { - compatible = "maxim,max1027"; - reg = <0>; - #io-channel-cells = <1>; - interrupt-parent = <&gpio5>; - interrupts = <15 IRQ_TYPE_EDGE_RISING>; - spi-max-frequency = <1000000>; - }; -}; diff --git a/Documentation/devicetree/bindings/iio/afe/voltage-divider.yaml b/Documentation/devicetree/bindings/iio/afe/voltage-divider.yaml new file mode 100644 index 000000000000..df2589f214e1 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/afe/voltage-divider.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/afe/voltage-divider.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Voltage divider + +maintainers: + - Peter Rosin <peda@axentia.se> + +description: | + When an io-channel measures the midpoint of a voltage divider, the + interesting voltage is often the voltage over the full resistance + of the divider. This binding describes the voltage divider in such + a curcuit. + + Vin ----. + | + .-----. + | R | + '-----' + | + +---- Vout + | + .-----. + | Rout| + '-----' + | + GND + + +properties: + compatible: + const: voltage-divider + + io-channels: + maxItems: 1 + description: | + Channel node of a voltage io-channel. + + output-ohms: + description: + Resistance Rout over which the output voltage is measured. See full-ohms. + + full-ohms: + description: + Resistance R + Rout for the full divider. The io-channel is scaled by + the Rout / (R + Rout) quotient. + +required: + - compatible + - io-channels + - output-ohms + - full-ohms + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + /* + * The system voltage is circa 12V, but divided down with a 22/222 + * voltage divider (R = 200 Ohms, Rout = 22 Ohms) and fed to an ADC. + */ + spi { + #address-cells = <1>; + #size-cells = <0>; + maxadc: adc@0 { + compatible = "maxim,max1027"; + reg = <0>; + #io-channel-cells = <1>; + interrupt-parent = <&gpio5>; + interrupts = <15 IRQ_TYPE_EDGE_RISING>; + spi-max-frequency = <1000000>; + }; + }; + sysv { + compatible = "voltage-divider"; + io-channels = <&maxadc 1>; + + /* Scale the system voltage by 22/222 to fit the ADC range. */ + output-ohms = <22>; + full-ohms = <222>; /* 200 + 22 */ + }; +... diff --git a/Documentation/devicetree/bindings/iio/chemical/bme680.txt b/Documentation/devicetree/bindings/iio/chemical/bme680.txt deleted file mode 100644 index 7f3827cfb2ff..000000000000 --- a/Documentation/devicetree/bindings/iio/chemical/bme680.txt +++ /dev/null @@ -1,11 +0,0 @@ -Bosch Sensortec BME680 pressure/temperature/humidity/voc sensors - -Required properties: -- compatible: must be "bosch,bme680" - -Example: - -bme680@76 { - compatible = "bosch,bme680"; - reg = <0x76>; -}; diff --git a/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt b/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt deleted file mode 100644 index 5844ed58173c..000000000000 --- a/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt +++ /dev/null @@ -1,15 +0,0 @@ -* Sensirion SGP30/SGPC3 multi-pixel Gas Sensor - -Required properties: - - - compatible: must be one of - "sensirion,sgp30" - "sensirion,sgpc3" - - reg: the I2C address of the sensor - -Example: - -gas@58 { - compatible = "sensirion,sgp30"; - reg = <0x58>; -}; diff --git a/Documentation/devicetree/bindings/iio/dac/ad5592r.txt b/Documentation/devicetree/bindings/iio/dac/ad5592r.txt deleted file mode 100644 index 989f96f31c66..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/ad5592r.txt +++ /dev/null @@ -1,155 +0,0 @@ -Analog Devices AD5592R/AD5593R DAC/ADC device driver - -Required properties for the AD5592R: - - compatible: Must be "adi,ad5592r" - - reg: SPI chip select number for the device - - spi-max-frequency: Max SPI frequency to use (< 30000000) - - spi-cpol: The AD5592R requires inverse clock polarity (CPOL) mode - -Required properties for the AD5593R: - - compatible: Must be "adi,ad5593r" - - reg: I2C address of the device - -Required properties for all supported chips: - - #address-cells: Should be 1. - - #size-cells: Should be 0. - - channel nodes: - Each child node represents one channel and has the following - Required properties: - * reg: Pin on which this channel is connected to. - * adi,mode: Mode or function of this channel. - Macros specifying the valid values - can be found in <dt-bindings/iio/adi,ad5592r.h>. - - The following values are currently supported: - * CH_MODE_UNUSED (the pin is unused) - * CH_MODE_ADC (the pin is ADC input) - * CH_MODE_DAC (the pin is DAC output) - * CH_MODE_DAC_AND_ADC (the pin is DAC output - but can be monitored by an ADC, since - there is no disadvantage this - this should be considered as the - preferred DAC mode) - * CH_MODE_GPIO (the pin is registered - with GPIOLIB) - Optional properties: - * adi,off-state: State of this channel when unused or the - device gets removed. Macros specifying the - valid values can be found in - <dt-bindings/iio/adi,ad5592r.h>. - - * CH_OFFSTATE_PULLDOWN (the pin is pulled down) - * CH_OFFSTATE_OUT_LOW (the pin is output low) - * CH_OFFSTATE_OUT_HIGH (the pin is output high) - * CH_OFFSTATE_OUT_TRISTATE (the pin is - tristated output) - - -Optional properties: - - vref-supply: Phandle to the external reference voltage supply. This should - only be set if there is an external reference voltage connected to the VREF - pin. If the property is not set the internal 2.5V reference is used. - - reset-gpios : GPIO spec for the RESET pin. If specified, it will be - asserted during driver probe. - - gpio-controller: Marks the device node as a GPIO controller. - - #gpio-cells: Should be 2. The first cell is the GPIO number and the second - cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. - -AD5592R Example: - - #include <dt-bindings/iio/adi,ad5592r.h> - - vref: regulator-vref { - compatible = "regulator-fixed"; - regulator-name = "vref-ad559x"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - ad5592r@0 { - #size-cells = <0>; - #address-cells = <1>; - #gpio-cells = <2>; - compatible = "adi,ad5592r"; - reg = <0>; - - spi-max-frequency = <1000000>; - spi-cpol; - - vref-supply = <&vref>; /* optional */ - reset-gpios = <&gpio0 86 0>; /* optional */ - gpio-controller; - - channel@0 { - reg = <0>; - adi,mode = <CH_MODE_DAC>; - }; - channel@1 { - reg = <1>; - adi,mode = <CH_MODE_ADC>; - }; - channel@2 { - reg = <2>; - adi,mode = <CH_MODE_DAC_AND_ADC>; - }; - channel@3 { - reg = <3>; - adi,mode = <CH_MODE_DAC_AND_ADC>; - adi,off-state = <CH_OFFSTATE_PULLDOWN>; - }; - channel@4 { - reg = <4>; - adi,mode = <CH_MODE_UNUSED>; - adi,off-state = <CH_OFFSTATE_PULLDOWN>; - }; - channel@5 { - reg = <5>; - adi,mode = <CH_MODE_GPIO>; - adi,off-state = <CH_OFFSTATE_PULLDOWN>; - }; - channel@6 { - reg = <6>; - adi,mode = <CH_MODE_GPIO>; - adi,off-state = <CH_OFFSTATE_PULLDOWN>; - }; - channel@7 { - reg = <7>; - adi,mode = <CH_MODE_GPIO>; - adi,off-state = <CH_OFFSTATE_PULLDOWN>; - }; - }; - -AD5593R Example: - - #include <dt-bindings/iio/adi,ad5592r.h> - - ad5593r@10 { - #size-cells = <0>; - #address-cells = <1>; - #gpio-cells = <2>; - compatible = "adi,ad5593r"; - reg = <0x10>; - gpio-controller; - - channel@0 { - reg = <0>; - adi,mode = <CH_MODE_DAC>; - adi,off-state = <CH_OFFSTATE_PULLDOWN>; - }; - channel@1 { - reg = <1>; - adi,mode = <CH_MODE_ADC>; - adi,off-state = <CH_OFFSTATE_PULLDOWN>; - }; - channel@2 { - reg = <2>; - adi,mode = <CH_MODE_DAC_AND_ADC>; - adi,off-state = <CH_OFFSTATE_PULLDOWN>; - }; - channel@6 { - reg = <6>; - adi,mode = <CH_MODE_GPIO>; - adi,off-state = <CH_OFFSTATE_PULLDOWN>; - }; - }; diff --git a/Documentation/devicetree/bindings/iio/dac/ad5758.txt b/Documentation/devicetree/bindings/iio/dac/ad5758.txt deleted file mode 100644 index 2f607f41f9d3..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/ad5758.txt +++ /dev/null @@ -1,83 +0,0 @@ -Analog Devices AD5758 DAC device driver - -Required properties for the AD5758: - - compatible: Must be "adi,ad5758" - - reg: SPI chip select number for the device - - spi-max-frequency: Max SPI frequency to use (< 50000000) - - spi-cpha: is the only mode that is supported - -Required properties: - - - adi,dc-dc-mode: Mode of operation of the dc-to-dc converter - Dynamic Power Control (DPC) - In this mode, the AD5758 circuitry senses the output - voltage and dynamically regulates the supply voltage, - VDPC+, to meet compliance requirements plus an optimized - headroom voltage for the output buffer. - - Programmable Power Control (PPC) - In this mode, the VDPC+ voltage is user-programmable to - a fixed level that needs to accommodate the maximum output - load required. - - The output of the DAC core is either converted to a - current or voltage output at the VIOUT pin. Only one mode - can be enabled at any one time. - - The following values are currently supported: - * 1: DPC current mode - * 2: DPC voltage mode - * 3: PPC current mode - - Depending on the selected output mode (voltage or current) one of the - two properties must - be present: - - - adi,range-microvolt: Voltage output range - The array of voltage output ranges must contain two fields: - * <0 5000000>: 0 V to 5 V voltage range - * <0 10000000>: 0 V to 10 V voltage range - * <(-5000000) 5000000>: ±5 V voltage range - * <(-10000000) 10000000>: ±10 V voltage range - - adi,range-microamp: Current output range - The array of current output ranges must contain two fields: - * <0 20000>: 0 mA to 20 mA current range - * <0 24000>: 0 mA to 24 mA current range - * <4 24000>: 4 mA to 20 mA current range - * <(-20000) 20000>: ±20 mA current range - * <(-24000) 24000>: ±24 mA current range - * <(-1000) 22000>: −1 mA to +22 mA current range - -Optional properties: - - - reset-gpios : GPIO spec for the RESET pin. If specified, it will be - asserted during driver probe. - - - adi,dc-dc-ilim-microamp: The dc-to-dc converter current limit - The following values are currently supported [uA]: - * 150000 - * 200000 - * 250000 - * 300000 - * 350000 - * 400000 - - - adi,slew-time-us: The time it takes for the output to reach the - full scale [uS] - The supported range is between 133us up to 1023984375us - -AD5758 Example: - - dac@0 { - compatible = "adi,ad5758"; - reg = <0>; - spi-max-frequency = <1000000>; - spi-cpha; - - reset-gpios = <&gpio 22 0>; - - adi,dc-dc-mode = <2>; - adi,range-microvolt = <0 10000000>; - adi,dc-dc-ilim-microamp = <200000>; - adi,slew-time-us = <125000>; - }; diff --git a/Documentation/devicetree/bindings/iio/dac/ad7303.txt b/Documentation/devicetree/bindings/iio/dac/ad7303.txt deleted file mode 100644 index 914610f0556e..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/ad7303.txt +++ /dev/null @@ -1,23 +0,0 @@ -Analog Devices AD7303 DAC device driver - -Required properties: - - compatible: Must be "adi,ad7303" - - reg: SPI chip select number for the device - - spi-max-frequency: Max SPI frequency to use (< 30000000) - - Vdd-supply: Phandle to the Vdd power supply - -Optional properties: - - REF-supply: Phandle to the external reference voltage supply. This should - only be set if there is an external reference voltage connected to the REF - pin. If the property is not set Vdd/2 is used as the reference voltage. - -Example: - - ad7303@4 { - compatible = "adi,ad7303"; - reg = <4>; - spi-max-frequency = <10000000>; - Vdd-supply = <&vdd_supply>; - adi,use-external-reference; - REF-supply = <&vref_supply>; - }; diff --git a/Documentation/devicetree/bindings/iio/dac/adi,ad5592r.yaml b/Documentation/devicetree/bindings/iio/dac/adi,ad5592r.yaml new file mode 100644 index 000000000000..30194880f457 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/adi,ad5592r.yaml @@ -0,0 +1,204 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/adi,ad5592r.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD5592R/AD5593R DAC/ADC + +maintainers: + - Michael Hennerich <michael.hennerich@analog.com> + +properties: + compatible: + enum: + - adi,ad5592r + - adi,ad5593r + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 30000000 + + spi-cpol: true + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + "#io-channel-cells": + const: 1 + + vref-supply: + description: If not set internal 2.5V reference used. + + reset-gpios: + maxItems: 1 + + gpio-controller: + description: Marks the device node as a GPIO controller. + + "#gpio-cells": + const: 2 + description: + The first cell is the GPIO number and the second cell specifies + GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + +allOf: + - if: + properties: + compatible: + contains: + const: adi,ad5592r + then: + required: + - spi-cpol + else: + properties: + spi-cpol: false + +additionalProperties: false + +patternProperties: + "^(channel@)[0-7]$": + type: object + description: Child node to describe a channel + properties: + reg: + minimum: 0 + maximum: 7 + + adi,mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 8] + description: | + Mode or function of this channel. + Macros specifying the valid values can be found in + <dt-bindings/iio/adi,ad5592r.h>. + + The following values are currently supported: + * CH_MODE_UNUSED (the pin is unused) + * CH_MODE_ADC (the pin is ADC input) + * CH_MODE_DAC (the pin is DAC output) + * CH_MODE_DAC_AND_ADC (the pin is DAC output but can be monitored + by an ADC, since there is no disadvantage this should be + considered as the preferred DAC mode) + * CH_MODE_GPIO (the pin is registered with GPIOLIB) + + adi,off-state: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + State of this channel when unused or the device gets removed. + Macros specifying the valid values can be found in + <dt-bindings/iio/adi,ad5592r.h>. + * CH_OFFSTATE_PULLDOWN (the pin is pulled down) + * CH_OFFSTATE_OUT_LOW (the pin is output low) + * CH_OFFSTATE_OUT_HIGH (the pin is output high) + * CH_OFFSTATE_OUT_TRISTATE (the pin is tristated output) + + required: + - reg + - adi,mode + + additionalProperties: false + +examples: + - | + #include <dt-bindings/iio/adi,ad5592r.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + addac@0 { + compatible = "adi,ad5592r"; + #size-cells = <0>; + #address-cells = <1>; + #gpio-cells = <2>; + reg = <0>; + + spi-max-frequency = <1000000>; + spi-cpol; + + vref-supply = <&vref>; + reset-gpios = <&gpio0 86 0>; + gpio-controller; + + channel@0 { + reg = <0>; + adi,mode = <CH_MODE_DAC>; + }; + channel@1 { + reg = <1>; + adi,mode = <CH_MODE_ADC>; + }; + channel@2 { + reg = <2>; + adi,mode = <CH_MODE_DAC_AND_ADC>; + }; + channel@3 { + reg = <3>; + adi,mode = <CH_MODE_DAC_AND_ADC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@4 { + reg = <4>; + adi,mode = <CH_MODE_UNUSED>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@5 { + reg = <5>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@6 { + reg = <6>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@7 { + reg = <7>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + }; + ad5593r@10 { + compatible = "adi,ad5593r"; + #size-cells = <0>; + #address-cells = <1>; + #gpio-cells = <2>; + reg = <0x10>; + gpio-controller; + + channel@0 { + reg = <0>; + adi,mode = <CH_MODE_DAC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@1 { + reg = <1>; + adi,mode = <CH_MODE_ADC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@2 { + reg = <2>; + adi,mode = <CH_MODE_DAC_AND_ADC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@6 { + reg = <6>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/adi,ad5686.yaml b/Documentation/devicetree/bindings/iio/dac/adi,ad5686.yaml new file mode 100644 index 000000000000..8065228e5df8 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/adi,ad5686.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/adi,ad5686.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD5686 and similar multi-channel DACs + +maintainers: + - Michael Auchter <michael.auchter@ni.com> + +description: | + Binding for Analog Devices AD5686 and similar multi-channel DACs + +properties: + compatible: + enum: + - adi,ad5311r + - adi,ad5338r + - adi,ad5671r + - adi,ad5675r + - adi,ad5691r + - adi,ad5692r + - adi,ad5693 + - adi,ad5693r + - adi,ad5694 + - adi,ad5694r + - adi,ad5695r + - adi,ad5696 + - adi,ad5696r + + reg: + maxItems: 1 + + vcc-supply: + description: | + The regulator supply for DAC reference voltage. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ad5686: dac@0 { + compatible = "adi,ad5686"; + reg = <0>; + vcc-supply = <&dac_vref>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/adi,ad5758.yaml b/Documentation/devicetree/bindings/iio/dac/adi,ad5758.yaml new file mode 100644 index 000000000000..626ccb6fe21e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/adi,ad5758.yaml @@ -0,0 +1,129 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/adi,ad5758.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD5758 DAC + +maintainers: + - Michael Hennerich <Michael.Hennerich@analog.com> + +properties: + compatible: + const: adi,ad5758 + + reg: + maxItems: 1 + + spi-max-frequency: true + spi-cpha: true + + adi,dc-dc-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 3] + description: | + Mode of operation of the dc-to-dc converter + Dynamic Power Control (DPC) + In this mode, the AD5758 circuitry senses the output voltage and + dynamically regulates the supply voltage, VDPC+, to meet compliance + requirements plus an optimized headroom voltage for the output buffer. + + Programmable Power Control (PPC) + In this mode, the VDPC+ voltage is user-programmable to a fixed level + that needs to accommodate the maximum output load required. + + The output of the DAC core is either converted to a current or + voltage output at the VIOUT pin. Only one mode can be enabled at + any one time. + + The following values are currently supported: + * 1: DPC current mode + * 2: DPC voltage mode + * 3: PPC current mode + + Depending on the selected output mode (voltage or current) one of the + two properties must be present: + + adi,range-microvolt: + $ref: /schemas/types.yaml#/definitions/int32-array + description: | + Voltage output range specified as <minimum, maximum> + enum: + - [[0, 5000000]] + - [[0, 10000000]] + - [[-5000000, 5000000]] + - [[-10000000, 10000000]] + + adi,range-microamp: + $ref: /schemas/types.yaml#/definitions/int32-array + description: | + Current output range specified as <minimum, maximum> + enum: + - [[0, 20000]] + - [[0, 24000]] + - [[4, 24000]] + - [[-20000, 20000]] + - [[-24000, 24000]] + - [[-1000, 22000]] + + reset-gpios: true + + adi,dc-dc-ilim-microamp: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [150000, 200000, 250000, 300000, 350000, 400000] + description: | + The dc-to-dc converter current limit. + + adi,slew-time-us: + description: | + The time it takes for the output to reach the full scale [uS] + minimum: 133 + maximum: 1023984375 + +required: + - compatible + - reg + - spi-cpha + - adi,dc-dc-mode + +allOf: + - if: + properties: + adi,dc-dc-mode: + contains: + enum: [1, 3] + then: + properties: + adi,range-microvolt: false + required: + - adi,range-microamp + else: + properties: + adi,range-microamp: false + required: + - adi,range-microvolt + +additionalProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + dac@0 { + compatible = "adi,ad5758"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpha; + + reset-gpios = <&gpio 22 0>; + + adi,dc-dc-mode = <2>; + adi,range-microvolt = <0 10000000>; + adi,dc-dc-ilim-microamp = <200000>; + adi,slew-time-us = <125000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/adi,ad7303.yaml b/Documentation/devicetree/bindings/iio/dac/adi,ad7303.yaml new file mode 100644 index 000000000000..1f0037152095 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/adi,ad7303.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/adi,ad7303.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD7303 DAC + +maintainers: + - Lars-Peter Clausen <lars@metafoo.de> + +properties: + compatible: + const: adi,ad7303 + + reg: + maxItems: 1 + + Vdd-supply: + description: + Used to calculate output channel scalling if REF-supply not specified. + REF-supply: + description: + If not provided, Vdd/2 is used as the reference voltage. + + spi-max-frequency: + maximum: 30000000 + +required: + - compatible + - reg + - Vdd-supply + +additionalProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + dac@4 { + compatible = "adi,ad7303"; + reg = <4>; + spi-max-frequency = <10000000>; + Vdd-supply = <&vdd_supply>; + REF-supply = <&vref_supply>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt b/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt deleted file mode 100644 index fdf47a01bfef..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt +++ /dev/null @@ -1,41 +0,0 @@ -Bindings for DAC emulation using a digital potentiometer - -It is assumed that the dpot is used as a voltage divider between the -current dpot wiper setting and the maximum resistance of the dpot. The -divided voltage is provided by a vref regulator. - - .------. - .-----------. | | - | vref |--' .---. - | regulator |--. | | - '-----------' | | d | - | | p | - | | o | wiper - | | t |<---------+ - | | | - | '---' dac output voltage - | | - '------+------------+ - -Required properties: -- compatible: Should be "dpot-dac" -- vref-supply: The regulator supplying the voltage divider. -- io-channels: Channel node of the dpot to be used for the voltage division. -- io-channel-names: Should be "dpot". - -Example: - - &i2c { - dpot: mcp4651-503@28 { - compatible = "microchip,mcp4651-503"; - reg = <0x28>; - #io-channel-cells = <1>; - }; - }; - - dac { - compatible = "dpot-dac"; - vref-supply = <®_3v3>; - io-channels = <&dpot 0>; - io-channel-names = "dpot"; - }; diff --git a/Documentation/devicetree/bindings/iio/dac/dpot-dac.yaml b/Documentation/devicetree/bindings/iio/dac/dpot-dac.yaml new file mode 100644 index 000000000000..6a7ca8e432d1 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/dpot-dac.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/dpot-dac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: DAC emulation using a digital potentiometer + +maintainers: + - Peter Rosin <peda@axentia.se> + +description: | + It is assumed that the dpot is used as a voltage divider between the + current dpot wiper setting and the maximum resistance of the dpot. The + divided voltage is provided by a vref regulator. + + .------. + .-----------. | | + | vref |--' .---. + | regulator |--. | | + '-----------' | | d | + | | p | + | | o | wiper + | | t |<---------+ + | | | + | '---' dac output voltage + | | + '------+------------+ + +properties: + compatible: + const: dpot-dac + + vref-supply: + description: Regulator supplying the voltage divider. + + io-channels: + maxItems: 1 + description: | + Channel node of the dpot to be used for the voltage division. + + io-channel-names: + const: dpot + + "#io-channel-cells": + const: 1 + +required: + - compatible + - vref-supply + - io-channels + - io-channel-names + +additionalProperties: false + +examples: + - | + dac { + compatible = "dpot-dac"; + vref-supply = <®_3v3>; + io-channels = <&dpot 0>; + io-channel-names = "dpot"; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/ds4424.txt b/Documentation/devicetree/bindings/iio/dac/ds4424.txt deleted file mode 100644 index eaebbf8dab40..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/ds4424.txt +++ /dev/null @@ -1,20 +0,0 @@ -Maxim Integrated DS4422/DS4424 7-bit Sink/Source Current DAC Device Driver - -Datasheet publicly available at: -https://datasheets.maximintegrated.com/en/ds/DS4422-DS4424.pdf - -Required properties: - - compatible: Should be one of - maxim,ds4422 - maxim,ds4424 - - reg: Should contain the DAC I2C address - -Optional properties: - - vcc-supply: Power supply is optional. If not defined, driver will ignore it. - -Example: - ds4224@10 { - compatible = "maxim,ds4424"; - reg = <0x10>; /* When A0, A1 pins are ground */ - vcc-supply = <&vcc_3v3>; - }; diff --git a/Documentation/devicetree/bindings/iio/dac/fsl,vf610-dac.yaml b/Documentation/devicetree/bindings/iio/dac/fsl,vf610-dac.yaml new file mode 100644 index 000000000000..999c715c6179 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/fsl,vf610-dac.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/fsl,vf610-dac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale vf610 Digital to Analog Converter + +maintainers: + - Sanchayan Maity <maitysanchayan@gmail.com> + +properties: + compatible: + const: fsl,vf610-dac + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: dac + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/vf610-clock.h> + bus@40000000 { + compatible = "fsl,aips-bus", "simple-bus"; + reg = <0x40000000 0x00070000>; + ranges; + #address-cells = <1>; + #size-cells = <1>; + dac@400cc000 { + compatible = "fsl,vf610-dac"; + reg = <0x400cc000 0x1000>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "dac"; + clocks = <&clks VF610_CLK_DAC0>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt b/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt deleted file mode 100644 index 42db783c4e75..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt +++ /dev/null @@ -1,19 +0,0 @@ -NXP LPC1850 DAC bindings - -Required properties: -- compatible: Should be "nxp,lpc1850-dac" -- reg: Offset and length of the register set for the ADC device -- interrupts: The interrupt number for the ADC device -- clocks: The root clock of the ADC controller -- vref-supply: The regulator supply ADC reference voltage -- resets: phandle to reset controller and line specifier - -Example: -dac: dac@400e1000 { - compatible = "nxp,lpc1850-dac"; - reg = <0x400e1000 0x1000>; - interrupts = <0>; - clocks = <&ccu1 CLK_APB3_DAC>; - vref-supply = <®_vdda>; - resets = <&rgu 42>; -}; diff --git a/Documentation/devicetree/bindings/iio/dac/max5821.txt b/Documentation/devicetree/bindings/iio/dac/max5821.txt deleted file mode 100644 index 54276ce8c971..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/max5821.txt +++ /dev/null @@ -1,14 +0,0 @@ -Maxim max5821 DAC device driver - -Required properties: - - compatible: Must be "maxim,max5821" - - reg: Should contain the DAC I2C address - - vref-supply: Phandle to the vref power supply - -Example: - - max5821@38 { - compatible = "maxim,max5821"; - reg = <0x38>; - vref-supply = <®_max5821>; - }; diff --git a/Documentation/devicetree/bindings/iio/dac/maxim,ds4424.yaml b/Documentation/devicetree/bindings/iio/dac/maxim,ds4424.yaml new file mode 100644 index 000000000000..264fa7c5fe3a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/maxim,ds4424.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/maxim,ds4424.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim Integrated DS4422/DS4424 7-bit Sink/Source Current DAC + +maintainers: + - Ismail Kose <ihkose@gmail.com> + +description: | + Datasheet publicly available at: + https://datasheets.maximintegrated.com/en/ds/DS4422-DS4424.pdf + +properties: + compatible: + enum: + - maxim,ds4422 + - maxim,ds4424 + + reg: + maxItems: 1 + + vcc-supply: true + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + dac@10 { + compatible = "maxim,ds4424"; + reg = <0x10>; /* When A0, A1 pins are ground */ + vcc-supply = <&vcc_3v3>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/maxim,max5821.yaml b/Documentation/devicetree/bindings/iio/dac/maxim,max5821.yaml new file mode 100644 index 000000000000..c43fb5f3f8ac --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/maxim,max5821.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/maxim,max5821.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim max5821 dual 10-bit DAC + +maintainers: + - Philippe Reynes <tremyfr@yahoo.fr> + +description: | + Datasheet publicly available at: + https://datasheets.maximintegrated.com/en/ds/MAX5821.pdf + +properties: + compatible: + const: maxim,max5821 + + reg: + maxItems: 1 + + vref-supply: true + +required: + - compatible + - reg + - vref-supply + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + dac@38 { + compatible = "maxim,max5821"; + reg = <0x38>; + vref-supply = <®_max5821>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/mcp4725.txt b/Documentation/devicetree/bindings/iio/dac/mcp4725.txt deleted file mode 100644 index 1bc6c093fbfe..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/mcp4725.txt +++ /dev/null @@ -1,35 +0,0 @@ -Microchip mcp4725 and mcp4726 DAC device driver - -Required properties: - - compatible: Must be "microchip,mcp4725" or "microchip,mcp4726" - - reg: Should contain the DAC I2C address - - vdd-supply: Phandle to the Vdd power supply. This supply is used as a - voltage reference on mcp4725. It is used as a voltage reference on - mcp4726 if there is no vref-supply specified. - -Optional properties (valid only for mcp4726): - - vref-supply: Optional phandle to the Vref power supply. Vref pin is - used as a voltage reference when this supply is specified. - - microchip,vref-buffered: Boolean to enable buffering of the external - Vref pin. This boolean is not valid without the vref-supply. Quoting - the datasheet: This is offered in cases where the reference voltage - does not have the current capability not to drop its voltage when - connected to the internal resistor ladder circuit. - -Examples: - - /* simple mcp4725 */ - mcp4725@60 { - compatible = "microchip,mcp4725"; - reg = <0x60>; - vdd-supply = <&vdac_vdd>; - }; - - /* mcp4726 with the buffered external reference voltage */ - mcp4726@60 { - compatible = "microchip,mcp4726"; - reg = <0x60>; - vdd-supply = <&vdac_vdd>; - vref-supply = <&vdac_vref>; - microchip,vref-buffered; - }; diff --git a/Documentation/devicetree/bindings/iio/dac/microchip,mcp4725.yaml b/Documentation/devicetree/bindings/iio/dac/microchip,mcp4725.yaml new file mode 100644 index 000000000000..271998610ceb --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/microchip,mcp4725.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/microchip,mcp4725.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip mcp4725 and mcp4726 DAC + +maintainers: + - Tomas Novotny <tomas@novotny.cz> + +properties: + compatible: + enum: + - microchip,mcp4725 + - microchip,mcp4726 + + reg: + maxItems: 1 + + vdd-supply: + description: | + Provides both power and acts as the reference supply on the mcp4725. + For the mcp4726 it will be used as the reference voltage if vref-supply + is not provided. + + vref-supply: + description: + Vref pin is used as a voltage reference when this supply is specified. + + microchip,vref-buffered: + type: boolean + description: | + Enable buffering of the external Vref pin. This boolean is not valid + without the vref-supply. Quoting the datasheet: This is offered in + cases where the reference voltage does not have the current + capability not to drop its voltage when connected to the internal + resistor ladder circuit. + +allOf: + - if: + not: + properties: + compatible: + contains: + const: microchip,mcp4726 + then: + properties: + vref-supply: false + microchip,vref-buffered: false + +required: + - compatible + - reg + - vdd-supply + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + mcp4725@60 { + compatible = "microchip,mcp4725"; + reg = <0x60>; + vdd-supply = <&vdac_vdd>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/nxp,lpc1850-dac.yaml b/Documentation/devicetree/bindings/iio/dac/nxp,lpc1850-dac.yaml new file mode 100644 index 000000000000..595f481c548e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/nxp,lpc1850-dac.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/nxp,lpc1850-dac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP LPC1850 DAC bindings + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: + Supports the DAC found on the LPC1850 SoC. + +properties: + compatible: + const: nxp,lpc1850-dac + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + vref-supply: true + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - vref-supply + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/lpc18xx-ccu.h> + soc { + #address-cells = <1>; + #size-cells = <1>; + dac: dac@400e1000 { + compatible = "nxp,lpc1850-dac"; + reg = <0x400e1000 0x1000>; + interrupts = <0>; + clocks = <&ccu1 CLK_APB3_DAC>; + vref-supply = <®_vdda>; + resets = <&rgu 42>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac5571.txt b/Documentation/devicetree/bindings/iio/dac/ti,dac5571.txt deleted file mode 100644 index 03af6b9a4d07..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/ti,dac5571.txt +++ /dev/null @@ -1,24 +0,0 @@ -* Texas Instruments DAC5571 Family - -Required properties: - - compatible: Should contain - "ti,dac5571" - "ti,dac6571" - "ti,dac7571" - "ti,dac5574" - "ti,dac6574" - "ti,dac7574" - "ti,dac5573" - "ti,dac6573" - "ti,dac7573" - - reg: Should contain the DAC I2C address - -Optional properties: - - vref-supply: The regulator supply for DAC reference voltage - -Example: -dac@0 { - compatible = "ti,dac5571"; - reg = <0x4C>; - vref-supply = <&vdd_supply>; -}; diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac5571.yaml b/Documentation/devicetree/bindings/iio/dac/ti,dac5571.yaml new file mode 100644 index 000000000000..714191724f7c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ti,dac5571.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/ti,dac5571.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DAC5571 Family + +maintainers: + - Sean Nyekjaer <sean@geanix.com> + +properties: + compatible: + enum: + - ti,dac5571 + - ti,dac6571 + - ti,dac7571 + - ti,dac5574 + - ti,dac6574 + - ti,dac7574 + - ti,dac5573 + - ti,dac6573 + - ti,dac7573 + + reg: + maxItems: 1 + + vref-supply: + description: + Reference voltage must be supplied to establish the scaling of the + output voltage. + +required: + - compatible + - reg + - vref-supply + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + dac@4c { + compatible = "ti,dac5571"; + reg = <0x4C>; + vref-supply = <&vdd_supply>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac7311.txt b/Documentation/devicetree/bindings/iio/dac/ti,dac7311.txt deleted file mode 100644 index e5a507db5e01..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/ti,dac7311.txt +++ /dev/null @@ -1,23 +0,0 @@ -TI DAC7311 device tree bindings - -Required properties: -- compatible: must be set to: - * "ti,dac7311" - * "ti,dac6311" - * "ti,dac5311" -- reg: spi chip select number for the device -- vref-supply: The regulator supply for ADC reference voltage - -Optional properties: -- spi-max-frequency: Max SPI frequency to use - -Example: - - spi_master { - dac@0 { - compatible = "ti,dac7311"; - reg = <0>; /* CS0 */ - spi-max-frequency = <1000000>; - vref-supply = <&vdd_supply>; - }; - }; diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac7311.yaml b/Documentation/devicetree/bindings/iio/dac/ti,dac7311.yaml new file mode 100644 index 000000000000..10be98d1f19c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ti,dac7311.yaml @@ -0,0 +1,49 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/ti,dac7311.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DAC5311 and similar SPI DACs + +maintainers: + - Charles-Antoine Couret <charles-antoine.couret@essensium.com> + +properties: + compatible: + enum: + - ti,dac7311 + - ti,dac6311 + - ti,dac5311 + + reg: + maxItems: 1 + + vref-supply: + description: + Reference voltage must be supplied to establish the scaling of the + output voltage. + + spi-max-frequency: true + +required: + - compatible + - reg + - vref-supply + +additionalProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + dac@0 { + compatible = "ti,dac7311"; + reg = <0>; /* CS0 */ + spi-max-frequency = <1000000>; + vref-supply = <&vdd_supply>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac7512.txt b/Documentation/devicetree/bindings/iio/dac/ti,dac7512.txt deleted file mode 100644 index 1db45939dac9..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/ti,dac7512.txt +++ /dev/null @@ -1,20 +0,0 @@ -TI DAC7512 DEVICETREE BINDINGS - -Required properties: - - - "compatible" Must be set to "ti,dac7512" - -Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt -apply. In particular, "reg" and "spi-max-frequency" properties must be given. - - -Example: - - spi_master { - dac7512: dac7512@0 { - compatible = "ti,dac7512"; - reg = <0>; /* CS0 */ - spi-max-frequency = <1000000>; - }; - }; - diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac7512.yaml b/Documentation/devicetree/bindings/iio/dac/ti,dac7512.yaml new file mode 100644 index 000000000000..4277cf8a4a2e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ti,dac7512.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/ti,dac7512.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DAC7512 DAC + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +properties: + compatible: + const: ti,dac7512 + + reg: + maxItems: 1 + + spi-max-frequency: + description: + Maximum frequency is reduced for supply voltage of less than 3.6V + maximum: 30000000 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + dac@0 { + compatible = "ti,dac7512"; + reg = <0>; /* CS0 */ + spi-max-frequency = <1000000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt b/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt deleted file mode 100644 index 17af395b99d9..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt +++ /dev/null @@ -1,28 +0,0 @@ -* Texas Instruments Dual, 12-Bit Serial Input Digital-to-Analog Converter - -The DAC7612 is a dual, 12-bit digital-to-analog converter (DAC) with guaranteed -12-bit monotonicity performance over the industrial temperature range. -Is is programmable through an SPI interface. - -The internal DACs are loaded when the LOADDACS pin is pulled down. - -https://www.ti.com/lit/ds/sbas106/sbas106.pdf - -Required Properties: -- compatible: Should be one of: - "ti,dac7612" - "ti,dac7612u" - "ti,dac7612ub" -- reg: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt - -Optional Properties: -- ti,loaddacs-gpios: GPIO descriptor for the LOADDACS pin. -- spi-*: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt - -Example: - - dac@1 { - compatible = "ti,dac7612"; - reg = <0x1>; - ti,loaddacs-gpios = <&msmgpio 25 GPIO_ACTIVE_LOW>; - }; diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac7612.yaml b/Documentation/devicetree/bindings/iio/dac/ti,dac7612.yaml new file mode 100644 index 000000000000..d172b142f6ed --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ti,dac7612.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/ti,dac7612.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DAC7612 family of DACs + +description: + The DAC7612 is a dual, 12-bit digital-to-analog converter (DAC) with + guaranteed 12-bit monotonicity performance over the industrial temperature + range. Is is programmable through an SPI interface. + +maintainers: + - Ricardo Ribalda Delgado <ricardo@ribalda.com> + +properties: + compatible: + enum: + - ti,dac7612 + - ti,dac7612u + - ti,dac7612ub + + reg: + maxItems: 1 + + ti,loaddacs-gpios: + description: + DACs are loaded when the pin connected to this GPIO is pulled low. + maxItems: 1 + + spi-max-frequency: true + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + dac@1 { + compatible = "ti,dac7612"; + reg = <0x1>; + ti,loaddacs-gpios = <&msmgpio 25 GPIO_ACTIVE_LOW>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt b/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt deleted file mode 100644 index 20c6c7ae9687..000000000000 --- a/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt +++ /dev/null @@ -1,20 +0,0 @@ -Freescale vf610 Digital to Analog Converter bindings - -The devicetree bindings are for the new DAC driver written for -vf610 SoCs from Freescale. - -Required properties: -- compatible: Should contain "fsl,vf610-dac" -- reg: Offset and length of the register set for the device -- interrupts: Should contain the interrupt for the device -- clocks: The clock is needed by the DAC controller -- clock-names: Must contain "dac" matching entry in the clocks property. - -Example: -dac0: dac@400cc000 { - compatible = "fsl,vf610-dac"; - reg = <0x400cc000 0x1000>; - interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "dac"; - clocks = <&clks VF610_CLK_DAC0>; -}; diff --git a/Documentation/devicetree/bindings/iio/frequency/adf4350.txt b/Documentation/devicetree/bindings/iio/frequency/adf4350.txt deleted file mode 100644 index f8c181d81d2d..000000000000 --- a/Documentation/devicetree/bindings/iio/frequency/adf4350.txt +++ /dev/null @@ -1,86 +0,0 @@ -Analog Devices ADF4350/ADF4351 device driver - -Required properties: - - compatible: Should be one of - * "adi,adf4350": When using the ADF4350 device - * "adi,adf4351": When using the ADF4351 device - - reg: SPI chip select numbert for the device - - spi-max-frequency: Max SPI frequency to use (< 20000000) - - clocks: From common clock binding. Clock is phandle to clock for - ADF435x Reference Clock (CLKIN). - -Optional properties: - - gpios: GPIO Lock detect - If set with a valid phandle and GPIO number, - pll lock state is tested upon read. - - adi,channel-spacing: Channel spacing in Hz (influences MODULUS). - - adi,power-up-frequency: If set in Hz the PLL tunes to - the desired frequency on probe. - - adi,reference-div-factor: If set the driver skips dynamic calculation - and uses this default value instead. - - adi,reference-doubler-enable: Enables reference doubler. - - adi,reference-div2-enable: Enables reference divider. - - adi,phase-detector-polarity-positive-enable: Enables positive phase - detector polarity. Default = negative. - - adi,lock-detect-precision-6ns-enable: Enables 6ns lock detect precision. - Default = 10ns. - - adi,lock-detect-function-integer-n-enable: Enables lock detect - for integer-N mode. Default = factional-N mode. - - adi,charge-pump-current: Charge pump current in mA. - Default = 2500mA. - - adi,muxout-select: On chip multiplexer output selection. - Valid values for the multiplexer output are: - 0: Three-State Output (default) - 1: DVDD - 2: DGND - 3: R-Counter output - 4: N-Divider output - 5: Analog lock detect - 6: Digital lock detect - - adi,low-spur-mode-enable: Enables low spur mode. - Default = Low noise mode. - - adi,cycle-slip-reduction-enable: Enables cycle slip reduction. - - adi,charge-cancellation-enable: Enabled charge pump - charge cancellation for integer-N modes. - - adi,anti-backlash-3ns-enable: Enables 3ns antibacklash pulse width - for integer-N modes. - - adi,band-select-clock-mode-high-enable: Enables faster band - selection logic. - - adi,12bit-clk-divider: Clock divider value used when - adi,12bit-clkdiv-mode != 0 - - adi,clk-divider-mode: - Valid values for the clkdiv mode are: - 0: Clock divider off (default) - 1: Fast lock enable - 2: Phase resync enable - - adi,aux-output-enable: Enables auxiliary RF output. - - adi,aux-output-fundamental-enable: Selects fundamental VCO output on - the auxiliary RF output. Default = Output of RF dividers. - - adi,mute-till-lock-enable: Enables Mute-Till-Lock-Detect function. - - adi,output-power: Output power selection. - Valid values for the power mode are: - 0: -4dBm (default) - 1: -1dBm - 2: +2dBm - 3: +5dBm - - adi,aux-output-power: Auxiliary output power selection. - Valid values for the power mode are: - 0: -4dBm (default) - 1: -1dBm - 2: +2dBm - 3: +5dBm - - -Example: - lo_pll0_rx_adf4351: adf4351-rx-lpc@4 { - compatible = "adi,adf4351"; - reg = <4>; - spi-max-frequency = <10000000>; - clocks = <&clk0_ad9523 9>; - clock-names = "clkin"; - adi,channel-spacing = <10000>; - adi,power-up-frequency = <2400000000>; - adi,phase-detector-polarity-positive-enable; - adi,charge-pump-current = <2500>; - adi,output-power = <3>; - adi,mute-till-lock-enable; - }; diff --git a/Documentation/devicetree/bindings/iio/frequency/adi,adf4350.yaml b/Documentation/devicetree/bindings/iio/frequency/adi,adf4350.yaml new file mode 100644 index 000000000000..d7f20b8518e0 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/frequency/adi,adf4350.yaml @@ -0,0 +1,190 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/frequency/adi,adf4350.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADF4350/ADF4351 wideband synthesizer + +maintainers: + - Michael Hennerich <michael.hennerich@analog.com> + +properties: + compatible: + enum: + - adi,adf4350 + - adi,adf4351 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 20000000 + + clocks: + maxItems: 1 + description: Clock to provide CLKIN reference clock signal. + + clock-names: + const: clkin + + gpios: + maxItems: 1 + description: Lock detect GPIO. + + adi,channel-spacing: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Channel spacing in Hz (influences MODULUS). + + adi,power-up-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + If set the PLL tunes to this frequency (in Hz) on driver probe. + + adi,reference-div-factor: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + If set the driver skips dynamic calculation and uses this default + value instead. + + adi,reference-doubler-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables reference doubler. + + adi,reference-div2-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables reference divider. + + adi,phase-detector-polarity-positive-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables positive phase detector polarity. Default negative. + + adi,lock-detect-precision-6ns-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables 6ns lock detect precision. Default = 10ns. + + adi,lock-detect-function-integer-n-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enables lock detect for integer-N mode. Default = factional-N mode. + + adi,charge-pump-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Charge pump current in mA. Default = 2500mA. + + adi,muxout-select: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 6 + description: | + On chip multiplexer output selection. + Valid values for the multiplexer output are: + 0: Three-State Output (default) + 1: DVDD + 2: DGND + 3: R-Counter output + 4: N-Divider output + 5: Analog lock detect + 6: Digital lock detect + + adi,low-spur-mode-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables low spur mode. Default = Low noise mode. + + adi,cycle-slip-reduction-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables cycle slip reduction. + + adi,charge-cancellation-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enabled charge pump charge cancellation for integer-N modes. + + adi,anti-backlash-3ns-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enables 3ns antibacklash pulse width for integer-N modes. + + adi,band-select-clock-mode-high-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables faster band selection logic. + + adi,12bit-clk-divider: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Clock divider value used when adi,12bit-clkdiv-mode != 0 + + adi,clk-divider-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + description: | + Valid values for the clkdiv mode are: + 0: Clock divider off (default) + 1: Fast lock enable + 2: Phase resync enable + + adi,aux-output-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables auxiliary RF output. + + adi,aux-output-fundamental-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Selects fundamental VCO output on the auxiliary RF output. + Default = Output of RF dividers. + + adi,mute-till-lock-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables Mute-Till-Lock-Detect function. + + adi,output-power: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Output power selection. + Valid values for the power mode are: + 0: -4dBm (default) + 1: -1dBm + 2: +2dBm + 3: +5dBm + + adi,aux-output-power: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Auxiliary output power selection. + Valid values for the power mode are: + 0: -4dBm (default) + 1: -1dBm + 2: +2dBm + 3: +5dBm + +additionalProperties: false + +required: + - compatible + - reg + - clocks + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + pll@4 { + compatible = "adi,adf4351"; + reg = <4>; + spi-max-frequency = <10000000>; + clocks = <&clk0_ad9523 9>; + clock-names = "clkin"; + adi,channel-spacing = <10000>; + adi,power-up-frequency = <2400000000>; + adi,phase-detector-polarity-positive-enable; + adi,charge-pump-current = <2500>; + adi,output-power = <3>; + adi,mute-till-lock-enable; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/gyroscope/bmg160.txt b/Documentation/devicetree/bindings/iio/gyroscope/bmg160.txt deleted file mode 100644 index bb43d1ad9c9f..000000000000 --- a/Documentation/devicetree/bindings/iio/gyroscope/bmg160.txt +++ /dev/null @@ -1,20 +0,0 @@ -* Bosch BMG160 triaxial rotation sensor (gyroscope) - -Required properties: - - - compatible : should be "bosch,bmg160", "bosch,bmi055_gyro" or "bosch,bmi088_gyro" - - reg : the I2C address of the sensor (0x69) - -Optional properties: - - - interrupts : interrupt mapping for GPIO IRQ, it should by configured with - flags IRQ_TYPE_EDGE_RISING - -Example: - -bmg160@69 { - compatible = "bosch,bmg160"; - reg = <0x69>; - interrupt-parent = <&gpio6>; - interrupts = <18 (IRQ_TYPE_EDGE_RISING)>; -}; diff --git a/Documentation/devicetree/bindings/iio/gyroscope/bosch,bmg160.yaml b/Documentation/devicetree/bindings/iio/gyroscope/bosch,bmg160.yaml new file mode 100644 index 000000000000..0466483be6bb --- /dev/null +++ b/Documentation/devicetree/bindings/iio/gyroscope/bosch,bmg160.yaml @@ -0,0 +1,46 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/gyroscope/bosch,bmg160.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bosch BMG160 triaxial rotation sensor (gyroscope) + +maintainers: + - H. Nikolaus Schaller <hns@goldelico.com> + +properties: + compatible: + enum: + - bosch,bmg160 + - bosch,bmi055_gyro + - bosch,bmi088_gyro + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + description: + Should be configured with type IRQ_TYPE_EDGE_RISING. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + gyroscope@69 { + compatible = "bosch,bmg160"; + reg = <0x69>; + interrupt-parent = <&gpio6>; + interrupts = <18 IRQ_TYPE_EDGE_RISING>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/gyroscope/nxp,fxas21002c.txt b/Documentation/devicetree/bindings/iio/gyroscope/nxp,fxas21002c.txt deleted file mode 100644 index 465e104bbf14..000000000000 --- a/Documentation/devicetree/bindings/iio/gyroscope/nxp,fxas21002c.txt +++ /dev/null @@ -1,31 +0,0 @@ -* NXP FXAS21002C Gyroscope device tree bindings - -http://www.nxp.com/products/sensors/gyroscopes/3-axis-digital-gyroscope:FXAS21002C - -Required properties: - - compatible : should be "nxp,fxas21002c" - - reg : the I2C address of the sensor or SPI chip select number for the - device. - - vdd-supply: phandle to the regulator that provides power to the sensor. - - vddio-supply: phandle to the regulator that provides power to the bus. - -Optional properties: - - reset-gpios : gpio used to reset the device, see gpio/gpio.txt - - interrupts : device support 2 interrupts, INT1 and INT2, - the interrupts can be triggered on rising or falling edges. - See interrupt-controller/interrupts.txt - - interrupt-names: should contain "INT1" or "INT2", the gyroscope interrupt - line in use. - - drive-open-drain: the interrupt/data ready line will be configured - as open drain, which is useful if several sensors share - the same interrupt line. This is a boolean property. - (This binding is taken from pinctrl/pinctrl-bindings.txt) - -Example: - -gyroscope@20 { - compatible = "nxp,fxas21002c"; - reg = <0x20>; - vdd-supply = <®_peri_3p15v>; - vddio-supply = <®_peri_3p15v>; -}; diff --git a/Documentation/devicetree/bindings/iio/gyroscope/nxp,fxas21002c.yaml b/Documentation/devicetree/bindings/iio/gyroscope/nxp,fxas21002c.yaml new file mode 100644 index 000000000000..d97ee774d6a6 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/gyroscope/nxp,fxas21002c.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/gyroscope/nxp,fxas21002c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP FXAS21002C Gyroscope + +maintainers: + - Rui Miguel Silva <rmfrfs@gmail.com> + +description: | + 3 axis digital gyroscope device with an I2C and SPI interface. + http://www.nxp.com/products/sensors/gyroscopes/3-axis-digital-gyroscope:FXAS21002C + +properties: + compatible: + const: nxp,fxas21002c + + reg: + maxItems: 1 + + vdd-supply: + description: Regulator that provides power to the sensor + + vddio-supply: + description: Regulator that provides power to the bus + + reset-gpios: + maxItems: 1 + description: GPIO connected to reset + + interrupts: + minItems: 1 + maxItems: 2 + description: Either interrupt may be triggered on rising or falling edges. + + interrupt-names: + minItems: 1 + maxItems: 2 + items: + enum: + - INT1 + - INT2 + + drive-open-drain: + type: boolean + description: the interrupt/data ready line will be configured as open drain, + which is useful if several sensors share the same interrupt + line. + + spi-max-frequency: + maximum: 2000000 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + gyroscope@20 { + compatible = "nxp,fxas21002c"; + reg = <0x20>; + + vdd-supply = <®_peri_3p15v>; + vddio-supply = <®_peri_3p15v>; + + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "INT1"; + }; + }; + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + gyroscope@0 { + compatible = "nxp,fxas2102c"; + reg = <0x0>; + + spi-max-frequency = <2000000>; + + interrupt-parent = <&gpio2>; + interrupts = <7 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "INT2"; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/health/afe4403.txt b/Documentation/devicetree/bindings/iio/health/afe4403.txt deleted file mode 100644 index 8e412054d6d5..000000000000 --- a/Documentation/devicetree/bindings/iio/health/afe4403.txt +++ /dev/null @@ -1,33 +0,0 @@ -Texas Instruments AFE4403 Heart rate and Pulse Oximeter - -Required properties: - - compatible : Should be "ti,afe4403". - - reg : SPI chip select address of device. - - tx-supply : Regulator supply to transmitting LEDs. - - interrupts : The interrupt line the device ADC_RDY pin is - connected to. For details refer to, - ../../interrupt-controller/interrupts.txt. - -Optional properties: - - reset-gpios : GPIO used to reset the device. - For details refer to, ../../gpio/gpio.txt. - -For other required and optional properties of SPI slave nodes -please refer to ../../spi/spi-bus.txt. - -Example: - -&spi0 { - heart_mon@0 { - compatible = "ti,afe4403"; - reg = <0>; - spi-max-frequency = <10000000>; - - tx-supply = <&vbat>; - - interrupt-parent = <&gpio1>; - interrupts = <28 IRQ_TYPE_EDGE_RISING>; - - reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; - }; -}; diff --git a/Documentation/devicetree/bindings/iio/health/afe4404.txt b/Documentation/devicetree/bindings/iio/health/afe4404.txt deleted file mode 100644 index 0b52830a0d9c..000000000000 --- a/Documentation/devicetree/bindings/iio/health/afe4404.txt +++ /dev/null @@ -1,29 +0,0 @@ -Texas Instruments AFE4404 Heart rate and Pulse Oximeter - -Required properties: - - compatible : Should be "ti,afe4404". - - reg : I2C address of the device. - - tx-supply : Regulator supply to transmitting LEDs. - - interrupts : The interrupt line the device ADC_RDY pin is - connected to. For details refer to, - ../interrupt-controller/interrupts.txt. - -Optional properties: - - reset-gpios : GPIO used to reset the device. - For details refer to, ../gpio/gpio.txt. - -Example: - -&i2c2 { - heart_mon@58 { - compatible = "ti,afe4404"; - reg = <0x58>; - - tx-supply = <&vbat>; - - interrupt-parent = <&gpio1>; - interrupts = <28 IRQ_TYPE_EDGE_RISING>; - - reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; - }; -}; diff --git a/Documentation/devicetree/bindings/iio/health/max30100.txt b/Documentation/devicetree/bindings/iio/health/max30100.txt deleted file mode 100644 index 0054908a6e74..000000000000 --- a/Documentation/devicetree/bindings/iio/health/max30100.txt +++ /dev/null @@ -1,28 +0,0 @@ -Maxim MAX30100 heart rate and pulse oximeter sensor - -* https://datasheets.maximintegrated.com/en/ds/MAX30100.pdf - -Required properties: - - compatible: must be "maxim,max30100" - - reg: the I2C address of the sensor - - interrupts: the sole interrupt generated by the device - - Refer to interrupt-controller/interrupts.txt for generic - interrupt client node bindings. - -Optional properties: - - maxim,led-current-microamp: configuration for LED current in microamperes - while the engine is running. First indexed value is the configuration for - the RED LED, and second value is for the IR LED. - - Refer to the datasheet for the allowed current values. - -Example: - -max30100@57 { - compatible = "maxim,max30100"; - reg = <0x57>; - maxim,led-current-microamp = <24000 50000>; - interrupt-parent = <&gpio1>; - interrupts = <16 2>; -}; diff --git a/Documentation/devicetree/bindings/iio/health/max30102.txt b/Documentation/devicetree/bindings/iio/health/max30102.txt deleted file mode 100644 index 7ef7ae40ae4f..000000000000 --- a/Documentation/devicetree/bindings/iio/health/max30102.txt +++ /dev/null @@ -1,33 +0,0 @@ -Maxim MAX30102 heart rate and pulse oximeter sensor -Maxim MAX30105 optical particle-sensing module - -* https://datasheets.maximintegrated.com/en/ds/MAX30102.pdf -* https://datasheets.maximintegrated.com/en/ds/MAX30105.pdf - -Required properties: - - compatible: must be "maxim,max30102" or "maxim,max30105" - - reg: the I2C address of the sensor - - interrupts: the sole interrupt generated by the device - - Refer to interrupt-controller/interrupts.txt for generic - interrupt client node bindings. - -Optional properties: - - maxim,red-led-current-microamp: configuration for red LED current - - maxim,ir-led-current-microamp: configuration for IR LED current - - maxim,green-led-current-microamp: configuration for green LED current - (max30105 only) - - Note that each step is approximately 200 microamps, ranging from 0 uA to - 50800 uA. - -Example: - -max30102@57 { - compatible = "maxim,max30102"; - reg = <0x57>; - maxim,red-led-current-microamp = <7000>; - maxim,ir-led-current-microamp = <7000>; - interrupt-parent = <&gpio1>; - interrupts = <16 2>; -}; diff --git a/Documentation/devicetree/bindings/iio/health/maxim,max30100.yaml b/Documentation/devicetree/bindings/iio/health/maxim,max30100.yaml new file mode 100644 index 000000000000..64b862637039 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/health/maxim,max30100.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/health/maxim,max30100.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX30100 heart rate and pulse oximeter sensor + +maintainers: + - Matt Ranostay <matt.ranostay@konsulko.com> + +properties: + compatible: + const: maxim,max30100 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + description: Connected to ADC_RDY pin. + + maxim,led-current-microamp: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: | + LED current whilst the engine is running. First indexed value is + the configuration for the RED LED, and second value is for the IR LED. + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + heart-rate@57 { + compatible = "maxim,max30100"; + reg = <0x57>; + maxim,led-current-microamp = <24000 50000>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/health/maxim,max30102.yaml b/Documentation/devicetree/bindings/iio/health/maxim,max30102.yaml new file mode 100644 index 000000000000..c13c10c8d65d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/health/maxim,max30102.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/health/maxim,max30102.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX30102 heart rate and pulse oximeter and MAX30105 particle-sensor + +maintainers: + - Matt Ranostay <matt.ranostay@konsulko.com> + +properties: + compatible: + enum: + - maxim,max30102 + - maxim,max30105 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + description: Connected to ADC_RDY pin. + + maxim,red-led-current-microamp: + description: RED LED current. Each step is approximately 200 microamps. + minimum: 0 + maximum: 50800 + + maxim,ir-led-current-microamp: + description: IR LED current. Each step is approximately 200 microamps. + minimum: 0 + maximum: 50800 + + maxim,green-led-current-microamp: + description: Green LED current. Each step is approximately 200 microamps. + minimum: 0 + maximum: 50800 + +allOf: + - if: + properties: + compatible: + contains: + const: maxim,max30100 + then: + properties: + maxim,green-led-current-microamp: false + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + heart-rate@57 { + compatible = "maxim,max30102"; + reg = <0x57>; + maxim,red-led-current-microamp = <7000>; + maxim,ir-led-current-microamp = <7000>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/health/ti,afe4403.yaml b/Documentation/devicetree/bindings/iio/health/ti,afe4403.yaml new file mode 100644 index 000000000000..d861526c5c42 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/health/ti,afe4403.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/health/ti,afe4403.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments AFE4403 Heart rate and Pulse Oximeter + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +properties: + compatible: + const: ti,afe4403 + + reg: + maxItems: 1 + + tx-supply: + description: Supply to transmitting LEDs. + + interrupts: + maxItems: 1 + description: Connected to ADC_RDY pin. + + reset-gpios: true + + spi-max-frequency: true + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + heart_mon@0 { + compatible = "ti,afe4403"; + reg = <0>; + spi-max-frequency = <10000000>; + tx-supply = <&vbat>; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_EDGE_RISING>; + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/health/ti,afe4404.yaml b/Documentation/devicetree/bindings/iio/health/ti,afe4404.yaml new file mode 100644 index 000000000000..3b4d6c48b8bb --- /dev/null +++ b/Documentation/devicetree/bindings/iio/health/ti,afe4404.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/health/ti,afe4404.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments AFE4404 Heart rate and Pulse Oximeter + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +properties: + compatible: + const: ti,afe4403 + + reg: + maxItems: 1 + + tx-supply: + description: Supply to transmitting LEDs. + + interrupts: + maxItems: 1 + description: Connected to ADC_RDY pin. + + reset-gpios: true + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + heart_mon@58 { + compatible = "ti,afe4404"; + reg = <0x58>; + tx-supply = <&vbat>; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_EDGE_RISING>; + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/humidity/dht11.txt b/Documentation/devicetree/bindings/iio/humidity/dht11.txt deleted file mode 100644 index ecc24c199fd6..000000000000 --- a/Documentation/devicetree/bindings/iio/humidity/dht11.txt +++ /dev/null @@ -1,14 +0,0 @@ -* DHT11 humidity/temperature sensor (and compatibles like DHT22) - -Required properties: - - compatible: Should be "dht11" - - gpios: Should specify the GPIO connected to the sensor's data - line, see "gpios property" in - Documentation/devicetree/bindings/gpio/gpio.txt. - -Example: - -humidity_sensor { - compatible = "dht11"; - gpios = <&gpio0 6 0>; -} diff --git a/Documentation/devicetree/bindings/iio/humidity/dht11.yaml b/Documentation/devicetree/bindings/iio/humidity/dht11.yaml new file mode 100644 index 000000000000..2247481d0203 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/dht11.yaml @@ -0,0 +1,41 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/humidity/dht11.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: DHT11 humidity + temperature sensor + +maintainers: + - Harald Geyer <harald@ccbib.org> + +description: | + A simple and low cost module providing a non standard single GPIO based + interface. It is believed the part is made by aosong but don't have + absolute confirmation of this, or what the aosong part number is. + +properties: + compatible: + const: dht11 + + reg: + maxItems: 1 + + gpios: + maxItems: 1 + description: + Single, interrupt capable, GPIO used to communicate with the device. + +required: + - compatible + - gpios + +additionalProperties: false + +examples: + - | + humidity_sensor { + compatible = "dht11"; + gpios = <&gpio0 6 0>; + }; +... diff --git a/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt b/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt deleted file mode 100644 index c52333bdfd19..000000000000 --- a/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt +++ /dev/null @@ -1,17 +0,0 @@ -* HDC100x temperature + humidity sensors - -Required properties: - - compatible: Should contain one of the following: - ti,hdc1000 - ti,hdc1008 - ti,hdc1010 - ti,hdc1050 - ti,hdc1080 - - reg: i2c address of the sensor - -Example: - -hdc100x@40 { - compatible = "ti,hdc1000"; - reg = <0x40>; -}; diff --git a/Documentation/devicetree/bindings/iio/humidity/hts221.txt b/Documentation/devicetree/bindings/iio/humidity/hts221.txt deleted file mode 100644 index 84d029372260..000000000000 --- a/Documentation/devicetree/bindings/iio/humidity/hts221.txt +++ /dev/null @@ -1,30 +0,0 @@ -* HTS221 STM humidity + temperature sensor - -Required properties: -- compatible: should be "st,hts221" -- reg: i2c address of the sensor / spi cs line - -Optional properties: -- drive-open-drain: the interrupt/data ready line will be configured - as open drain, which is useful if several sensors share the same - interrupt line. This is a boolean property. - If the requested interrupt is configured as IRQ_TYPE_LEVEL_HIGH or - IRQ_TYPE_EDGE_RISING a pull-down resistor is needed to drive the line - when it is not active, whereas a pull-up one is needed when interrupt - line is configured as IRQ_TYPE_LEVEL_LOW or IRQ_TYPE_EDGE_FALLING. - Refer to pinctrl/pinctrl-bindings.txt for the property description. -- interrupts: interrupt mapping for IRQ. It should be configured with - flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or - IRQ_TYPE_EDGE_FALLING. - - Refer to interrupt-controller/interrupts.txt for generic interrupt - client node bindings. - -Example: - -hts221@5f { - compatible = "st,hts221"; - reg = <0x5f>; - interrupt-parent = <&gpio0>; - interrupts = <0 IRQ_TYPE_EDGE_RISING>; -}; diff --git a/Documentation/devicetree/bindings/iio/humidity/htu21.txt b/Documentation/devicetree/bindings/iio/humidity/htu21.txt deleted file mode 100644 index 97d79636f7ae..000000000000 --- a/Documentation/devicetree/bindings/iio/humidity/htu21.txt +++ /dev/null @@ -1,13 +0,0 @@ -*HTU21 - Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor - -Required properties: - - - compatible: should be "meas,htu21" or "meas,ms8607-humidity" - - reg: I2C address of the sensor - -Example: - -htu21@40 { - compatible = "meas,htu21"; - reg = <0x40>; -}; diff --git a/Documentation/devicetree/bindings/iio/humidity/st,hts221.yaml b/Documentation/devicetree/bindings/iio/humidity/st,hts221.yaml new file mode 100644 index 000000000000..598473df74fa --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/st,hts221.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/humidity/st,hts221.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HTS221 STM humidity + temperature sensor + +maintainers: + - Lorenzo Bianconi <lorenzo@kernel.org> + +description: | + Humidity and temperature sensor with I2C interface and data ready + interrupt. + +properties: + compatible: + const: st,hts221 + + reg: + maxItems: 1 + + drive-open-drain: + type: boolean + description: + The interrupt/data ready line will be configured as open drain, which + is useful if several sensors share the same interrupt line. + + vdd-supply: true + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hts221@5f { + compatible = "st,hts221"; + reg = <0x5f>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/iio-bindings.txt b/Documentation/devicetree/bindings/iio/iio-bindings.txt deleted file mode 100644 index aa63cac7323e..000000000000 --- a/Documentation/devicetree/bindings/iio/iio-bindings.txt +++ /dev/null @@ -1,102 +0,0 @@ -This binding is derived from clock bindings, and based on suggestions -from Lars-Peter Clausen [1]. - -Sources of IIO channels can be represented by any node in the device -tree. Those nodes are designated as IIO providers. IIO consumer -nodes use a phandle and IIO specifier pair to connect IIO provider -outputs to IIO inputs. Similar to the gpio specifiers, an IIO -specifier is an array of one or more cells identifying the IIO -output on a device. The length of an IIO specifier is defined by the -value of a #io-channel-cells property in the IIO provider node. - -[1] https://marc.info/?l=linux-iio&m=135902119507483&w=2 - -==IIO providers== - -Required properties: -#io-channel-cells: Number of cells in an IIO specifier; Typically 0 for nodes - with a single IIO output and 1 for nodes with multiple - IIO outputs. - -Optional properties: -label: A symbolic name for the device. - - -Example for a simple configuration with no trigger: - - adc: voltage-sensor@35 { - compatible = "maxim,max1139"; - reg = <0x35>; - #io-channel-cells = <1>; - label = "voltage_feedback_group1"; - }; - -Example for a configuration with trigger: - - adc@35 { - compatible = "some-vendor,some-adc"; - reg = <0x35>; - - adc1: iio-device@0 { - #io-channel-cells = <1>; - /* other properties */ - }; - adc2: iio-device@1 { - #io-channel-cells = <1>; - /* other properties */ - }; - }; - -==IIO consumers== - -Required properties: -io-channels: List of phandle and IIO specifier pairs, one pair - for each IIO input to the device. Note: if the - IIO provider specifies '0' for #io-channel-cells, - then only the phandle portion of the pair will appear. - -Optional properties: -io-channel-names: - List of IIO input name strings sorted in the same - order as the io-channels property. Consumers drivers - will use io-channel-names to match IIO input names - with IIO specifiers. -io-channel-ranges: - Empty property indicating that child nodes can inherit named - IIO channels from this node. Useful for bus nodes to provide - and IIO channel to their children. - -For example: - - device { - io-channels = <&adc 1>, <&ref 0>; - io-channel-names = "vcc", "vdd"; - }; - -This represents a device with two IIO inputs, named "vcc" and "vdd". -The vcc channel is connected to output 1 of the &adc device, and the -vdd channel is connected to output 0 of the &ref device. - -==Example== - - adc: max1139@35 { - compatible = "maxim,max1139"; - reg = <0x35>; - #io-channel-cells = <1>; - }; - - ... - - iio-hwmon { - compatible = "iio-hwmon"; - io-channels = <&adc 0>, <&adc 1>, <&adc 2>, - <&adc 3>, <&adc 4>, <&adc 5>, - <&adc 6>, <&adc 7>, <&adc 8>, - <&adc 9>; - }; - - some_consumer { - compatible = "some-consumer"; - io-channels = <&adc 10>, <&adc 11>; - io-channel-names = "adc1", "adc2"; - }; diff --git a/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt b/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt deleted file mode 100644 index 5ff38728ff91..000000000000 --- a/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt +++ /dev/null @@ -1,26 +0,0 @@ -Analog Devices AD5933/AD5934 Impedance Converter, Network Analyzer - -https://www.analog.com/media/en/technical-documentation/data-sheets/AD5933.pdf -https://www.analog.com/media/en/technical-documentation/data-sheets/AD5934.pdf - -Required properties: - - compatible : should be one of - "adi,ad5933" - "adi,ad5934" - - reg : the I2C address. - - vdd-supply : The regulator supply for DVDD, AVDD1 and AVDD2 when they - are connected together. - -Optional properties: -- clocks : external clock reference. -- clock-names : must be "mclk" if clocks is set. - -Example for a I2C device node: - - impedance-analyzer@0d { - compatible = "adi,adxl345"; - reg = <0x0d>; - vdd-supply = <&vdd_supply>; - clocks = <&ref_clk>; - clock-names = "mclk"; - }; diff --git a/Documentation/devicetree/bindings/iio/impedance-analyzer/adi,ad5933.yaml b/Documentation/devicetree/bindings/iio/impedance-analyzer/adi,ad5933.yaml new file mode 100644 index 000000000000..2ad043554b9c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/impedance-analyzer/adi,ad5933.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/impedance-analyzer/adi,ad5933.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD5933/AD5934 Impedance Converter, Network Analyzer + +maintainers: + - Marcelo Schmitt <marcelo.schmitt1@gmail.com> + - Gabriel Capella <gabriel@capella.pro> + +description: | + https://www.analog.com/media/en/technical-documentation/data-sheets/AD5933.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/AD5934.pdf + +properties: + compatible: + enum: + - adi,ad5933 + - adi,ad5934 + + reg: + maxItems: 1 + + vdd-supply: + description: | + The regulator supply for DVDD, AVDD1 and AVDD2 when they + are connected together. Used to calculate voltage scaling of measurement + channels. + + clocks: + maxItems: 1 + + clock-names: + const: mclk + +additionalProperties: false + +required: + - compatible + - reg + - vdd-supply + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + impedance-analyzer@d { + compatible = "adi,ad5933"; + reg = <0x0d>; + vdd-supply = <&vdd_supply>; + clocks = <&ref_clk>; + clock-names = "mclk"; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt b/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt deleted file mode 100644 index cd903a1d880d..000000000000 --- a/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt +++ /dev/null @@ -1,86 +0,0 @@ - -Analog Devices ADIS16480 and similar IMUs - -Required properties for the ADIS16480: - -- compatible: Must be one of - * "adi,adis16375" - * "adi,adis16480" - * "adi,adis16485" - * "adi,adis16488" - * "adi,adis16490" - * "adi,adis16495-1" - * "adi,adis16495-2" - * "adi,adis16495-3" - * "adi,adis16497-1" - * "adi,adis16497-2" - * "adi,adis16497-3" -- reg: SPI chip select number for the device -- spi-max-frequency: Max SPI frequency to use - see: Documentation/devicetree/bindings/spi/spi-bus.txt -- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt -- spi-cpol: See Documentation/devicetree/bindings/spi/spi-bus.txt -- interrupts: interrupt mapping for IRQ, accepted values are: - * IRQF_TRIGGER_RISING - * IRQF_TRIGGER_FALLING - -Optional properties: - -- interrupt-names: Data ready line selection. Valid values are: - * DIO1 - * DIO2 - * DIO3 - * DIO4 - If this field is left empty, DIO1 is assigned as default data ready - signal. -- reset-gpios: must be the device tree identifier of the RESET pin. As the line - is active low, it should be marked GPIO_ACTIVE_LOW. -- clocks: phandle to the external clock. Should be set according to - "clock-names". - If this field is left empty together with the "clock-names" field, then - the internal clock is used. -- clock-names: The name of the external clock to be used. Valid values are: - * sync: In sync mode, the internal clock is disabled and the frequency - of the external clock signal establishes therate of data - collection and processing. See Fig 14 and 15 in the datasheet. - The clock-frequency must be: - * 3000 to 4500 Hz for adis1649x devices. - * 700 to 2400 Hz for adis1648x devices. - * pps: In Pulse Per Second (PPS) Mode, the rate of data collection and - production is equal to the product of the external clock - frequency and the scale factor in the SYNC_SCALE register, see - Table 154 in the datasheet. - The clock-frequency must be: - * 1 to 128 Hz for adis1649x devices. - * This mode is not supported by adis1648x devices. - If this field is left empty together with the "clocks" field, then the - internal clock is used. -- adi,ext-clk-pin: The DIOx line to be used as an external clock input. - Valid values are: - * DIO1 - * DIO2 - * DIO3 - * DIO4 - Each DIOx pin supports only one function at a time (data ready line - selection or external clock input). When a single pin has two - two assignments, the enable bit for the lower priority function - automatically resets to zero (disabling the lower priority function). - Data ready has highest priority. - If this field is left empty, DIO2 is assigned as default external clock - input pin. - -Example: - - imu@0 { - compatible = "adi,adis16495-1"; - reg = <0>; - spi-max-frequency = <3200000>; - spi-cpol; - spi-cpha; - interrupts = <25 IRQF_TRIGGER_FALLING>; - interrupt-parent = <&gpio>; - interrupt-names = "DIO2"; - clocks = <&adis16495_sync>; - clock-names = "sync"; - adi,ext-clk-pin = "DIO1"; - }; diff --git a/Documentation/devicetree/bindings/iio/imu/adi,adis16480.yaml b/Documentation/devicetree/bindings/iio/imu/adi,adis16480.yaml new file mode 100644 index 000000000000..5dbe24be9925 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/imu/adi,adis16480.yaml @@ -0,0 +1,130 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/imu/adi,adis16480.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADIS16480 and similar IMUs + +maintainers: + - Alexandru Ardelean <alexandru.ardelean@analog.com> + +properties: + compatible: + enum: + - adi,adis16375 + - adi,adis16480 + - adi,adis16485 + - adi,adis16488 + - adi,adis16490 + - adi,adis16495-1 + - adi,adis16495-2 + - adi,adis16495-3 + - adi,adis16497-1 + - adi,adis16497-2 + - adi,adis16497-3 + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + description: | + Accepted interrupt types are: + * IRQ_TYPE_EDGE_RISING + * IRQ_TYPE_EDGE_FALLING + + interrupt-names: + minItems: 1 + maxItems: 2 + description: + Default if not supplied is DIO1. + items: + enum: + - DIO1 + - DIO2 + - DIO3 + - DIO4 + + spi-max-frequency: true + + spi-cpha: true + spi-cpol: true + + reset-gpios: + maxItems: 1 + description: Connected to RESET pin which is active low. + + clocks: + maxItems: 1 + description: If not provided, then the internal clock is used. + + clock-names: + description: | + sync: In sync mode, the internal clock is disabled and the frequency + of the external clock signal establishes therate of data + collection and processing. See Fig 14 and 15 in the datasheet. + The clock-frequency must be: + * 3000 to 4500 Hz for adis1649x devices. + * 700 to 2400 Hz for adis1648x devices. + pps: In Pulse Per Second (PPS) Mode, the rate of data collection and + production is equal to the product of the external clock + frequency and the scale factor in the SYNC_SCALE register, see + Table 154 in the datasheet. + The clock-frequency must be: + * 1 to 128 Hz for adis1649x devices. + * This mode is not supported by adis1648x devices. + enum: + - sync + - pps + + adi,ext-clk-pin: + $ref: /schemas/types.yaml#/definitions/string + description: | + The DIOx line to be used as an external clock input. + Each DIOx pin supports only one function at a time (data ready line + selection or external clock input). When a single pin has two + two assignments, the enable bit for the lower priority function + automatically resets to zero (disabling the lower priority function). + Data ready has highest priority. + If not provided then DIO2 is assigned as default external clock + input pin. + enum: + - DIO1 + - DIO2 + - DIO3 + - DIO4 + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - spi-cpha + - spi-cpol + - spi-max-frequency + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + imu@0 { + compatible = "adi,adis16495-1"; + reg = <0>; + spi-max-frequency = <3200000>; + spi-cpol; + spi-cpha; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + interrupt-names = "DIO2"; + clocks = <&adis16495_sync>; + clock-names = "sync"; + adi,ext-clk-pin = "DIO1"; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/imu/st,lsm6dsx.yaml b/Documentation/devicetree/bindings/iio/imu/st,lsm6dsx.yaml new file mode 100644 index 000000000000..d9b3213318fb --- /dev/null +++ b/Documentation/devicetree/bindings/iio/imu/st,lsm6dsx.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/imu/st,lsm6dsx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STM 6-axis (acc + gyro) IMU Mems sensors + +maintainers: + - Lorenzo Bianconi <lorenzo@kernel.org> + +description: + Devices have both I2C and SPI interfaces. + +properties: + compatible: + enum: + - st,lsm6ds3 + - st,lsm6ds3h + - st,lsm6dsl + - st,lsm6dsm + - st,ism330dlc + - st,lsm6dso + - st,asm330lhh + - st,lsm6dsox + - st,lsm6dsr + - st,lsm6ds3tr-c + - st,ism330dhcx + - st,lsm9ds1-imu + - st,lsm6ds0 + - st,lsm6dsrx + - st,lsm6dst + - st,lsm6dsop + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + description: + Supports up to 2 interrupt lines via the INT1 and INT2 pins. + + spi-max-frequency: true + + vdd-supply: + description: if defined provides VDD power to the sensor. + + vddio-supply: + description: if defined provides VDD IO power to the sensor. + + st,drdy-int-pin: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: | + The pin on the package that will be used to signal data ready + enum: + - 1 + - 2 + + st,pullups: + type: boolean + description: enable/disable internal i2c controller pullup resistors. + + drive-open-drain: + type: boolean + description: + The interrupt/data ready line will be configured as open drain, which + is useful if several sensors share the same interrupt line. + + wakeup-source: + $ref: /schemas/types.yaml#/definitions/flag + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + imu@6b { + compatible = "st,lsm6dsm"; + reg = <0x6b>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt deleted file mode 100644 index cef4bc16fce1..000000000000 --- a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt +++ /dev/null @@ -1,48 +0,0 @@ -* ST_LSM6DSx driver for STM 6-axis (acc + gyro) imu Mems sensors - -Required properties: -- compatible: must be one of: - "st,lsm6ds3" - "st,lsm6ds3h" - "st,lsm6dsl" - "st,lsm6dsm" - "st,ism330dlc" - "st,lsm6dso" - "st,asm330lhh" - "st,lsm6dsox" - "st,lsm6dsr" - "st,lsm6ds3tr-c" - "st,ism330dhcx" - "st,lsm9ds1-imu" - "st,lsm6ds0" - "st,lsm6dsrx" -- reg: i2c address of the sensor / spi cs line - -Optional properties: -- st,drdy-int-pin: the pin on the package that will be used to signal - "data ready" (valid values: 1 or 2). -- st,pullups : enable/disable internal i2c controller pullup resistors. -- drive-open-drain: the interrupt/data ready line will be configured - as open drain, which is useful if several sensors share the same - interrupt line. This is a boolean property. - (This binding is taken from pinctrl/pinctrl-bindings.txt) - If the requested interrupt is configured as IRQ_TYPE_LEVEL_HIGH or - IRQ_TYPE_EDGE_RISING a pull-down resistor is needed to drive the line - when it is not active, whereas a pull-up one is needed when interrupt - line is configured as IRQ_TYPE_LEVEL_LOW or IRQ_TYPE_EDGE_FALLING. -- interrupts: interrupt mapping for IRQ. It should be configured with - flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or - IRQ_TYPE_EDGE_FALLING. -- wakeup-source: Enables wake up of host system on event. - - Refer to interrupt-controller/interrupts.txt for generic interrupt - client node bindings. - -Example: - -lsm6dsm@6b { - compatible = "st,lsm6dsm"; - reg = <0x6b>; - interrupt-parent = <&gpio0>; - interrupts = <0 IRQ_TYPE_EDGE_RISING>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/apds9300.txt b/Documentation/devicetree/bindings/iio/light/apds9300.txt deleted file mode 100644 index 3aa6db3ee99d..000000000000 --- a/Documentation/devicetree/bindings/iio/light/apds9300.txt +++ /dev/null @@ -1,21 +0,0 @@ -* Avago APDS9300 ambient light sensor - -https://www.avagotech.com/docs/AV02-1077EN - -Required properties: - - - compatible : should be "avago,apds9300" - - reg : the I2C address of the sensor - -Optional properties: - - - interrupts : interrupt mapping for GPIO IRQ - -Example: - -apds9300@39 { - compatible = "avago,apds9300"; - reg = <0x39>; - interrupt-parent = <&gpio2>; - interrupts = <29 8>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/apds9960.txt b/Documentation/devicetree/bindings/iio/light/apds9960.txt deleted file mode 100644 index c53ddb81c4aa..000000000000 --- a/Documentation/devicetree/bindings/iio/light/apds9960.txt +++ /dev/null @@ -1,21 +0,0 @@ -* Avago APDS9960 gesture/RGB/ALS/proximity sensor - -https://www.avagotech.com/docs/AV02-4191EN - -Required properties: - - - compatible: must be "avago,apds9960" - - reg: the I2c address of the sensor - - interrupts : the sole interrupt generated by the device - - Refer to interrupt-controller/interrupts.txt for generic interrupt client - node bindings. - -Example: - -apds9960@39 { - compatible = "avago,apds9960"; - reg = <0x39>; - interrupt-parent = <&gpio1>; - interrupts = <16 1>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/avago,apds9300.yaml b/Documentation/devicetree/bindings/iio/light/avago,apds9300.yaml new file mode 100644 index 000000000000..206af44f2c43 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/avago,apds9300.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/avago,apds9300.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Avago APDS9300 ambient light sensor + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: | + Datasheet at https://www.avagotech.com/docs/AV02-1077EN + +properties: + compatible: + const: avago,apds9300 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + light-sensor@39 { + compatible = "avago,apds9300"; + reg = <0x39>; + interrupt-parent = <&gpio2>; + interrupts = <29 8>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/avago,apds9960.yaml b/Documentation/devicetree/bindings/iio/light/avago,apds9960.yaml new file mode 100644 index 000000000000..f06e0fda5629 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/avago,apds9960.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/avago,apds9960.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Avago APDS9960 gesture/RGB/ALS/proximity sensor + +maintainers: + - Matt Ranostay <matt.ranostay@konsulko.com> + +description: | + Datasheet at https://www.avagotech.com/docs/AV02-4191EN + +properties: + compatible: + const: avago,apds9960 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + light-sensor@39 { + compatible = "avago,apds9960"; + reg = <0x39>; + interrupt-parent = <&gpio1>; + interrupts = <16 1>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/capella,cm3605.yaml b/Documentation/devicetree/bindings/iio/light/capella,cm3605.yaml new file mode 100644 index 000000000000..27972938b60d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/capella,cm3605.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/capella,cm3605.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: + Capella Microsystems CM3605 Ambient Light and Short Distance Proximity Sensor + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + - Kevin Tsai <ktsai@capellamicro.com> + +description: | + The CM3605 is an entirely analog part. However, it requires quite a bit of + software logic to interface a host operating system. + + This ALS and proximity sensor was one of the very first deployed in mobile + handsets, notably it is used in the very first Nexus One Android phone from + 2010. + +properties: + compatible: + const: capella,cm3605 + + aset-gpios: + maxItems: 1 + description: + ASET line (drive low to activate the ALS, should be flagged + GPIO_ACTIVE_LOW) + + interrupts: + maxItems: 1 + description: + Connected to the POUT (proximity sensor out) line. The edge + detection must be set to IRQ_TYPE_EDGE_BOTH so as to detect + movements toward and away from the proximity sensor. + + io-channels: + maxItems: 1 + description: + ADC channel used for converting the voltage from AOUT to a digital + representation. + + io-channel-names: + const: aout + + vdd-supply: true + + capella,aset-resistance-ohms: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [50000, 100000, 300000, 600000] + description: > + Sensitivity calibration resistance. Note that calibration curves + are only provided for specific allowed values. Default: 100 kOhms. + +required: + - compatible + - aset-gpios + - interrupts + - io-channels + - io-channel-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + light-sensor { + compatible = "capella,cm3605"; + vdd-supply = <&foo_reg>; + aset-gpios = <&foo_gpio 1 GPIO_ACTIVE_LOW>; + capella,aset-resistance-ohms = <100000>; + interrupts = <1 IRQ_TYPE_EDGE_BOTH>; + io-channels = <&adc 0x01>; + io-channel-names = "aout"; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/capella,cm36651.yaml b/Documentation/devicetree/bindings/iio/light/capella,cm36651.yaml new file mode 100644 index 000000000000..446d94f3a89f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/capella,cm36651.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/capella,cm36651.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Capella CM36651 I2C Proximity and Color Light sensor + +maintainers: + - Beomho Seo <beomho.seo@samsung.com> + +properties: + compatible: + const: capella,cm36651 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vled-supply: + description: | + Supply for the IR_LED which is part of the cm36651 for proximity detection. + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - vled-supply + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + light-sensor@18 { + compatible = "capella,cm36651"; + reg = <0x18>; + interrupt-parent = <&gpx0>; + interrupts = <2 0>; + vled-supply = <&ps_als_reg>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/cm3605.txt b/Documentation/devicetree/bindings/iio/light/cm3605.txt deleted file mode 100644 index 56331a79f9ab..000000000000 --- a/Documentation/devicetree/bindings/iio/light/cm3605.txt +++ /dev/null @@ -1,41 +0,0 @@ -Capella Microsystems CM3605 -Ambient Light and Short Distance Proximity Sensor - -The CM3605 is an entirely analog part which however require quite a bit of -software logic to interface a host operating system. - -This ALS and proximity sensor was one of the very first deployed in mobile -handsets, notably it is used in the very first Nexus One Android phone from -2010. - -Required properties: -- compatible: must be: "capella,cm3605" -- aset-gpios: GPIO line controlling the ASET line (drive low - to activate the ALS, should be flagged GPIO_ACTIVE_LOW) -- interrupts: the IRQ line (such as a GPIO) that is connected to - the POUT (proximity sensor out) line. The edge detection must - be set to IRQ_TYPE_EDGE_BOTH so as to detect movements toward - and away from the proximity sensor. -- io-channels: the ADC channel used for converting the voltage from - AOUT to a digital representation. -- io-channel-names: must be "aout" - -Optional properties: -- vdd-supply: regulator supplying VDD power to the component. -- capella,aset-resistance-ohms: the sensitivity calibration resistance, - in Ohms. Valid values are: 50000, 100000, 300000 and 600000, - as these are the resistance values that we are supplied with - calibration curves for. If not supplied, 100 kOhm will be assumed - but it is strongly recommended to supply this. - -Example: - -cm3605 { - compatible = "capella,cm3605"; - vdd-supply = <&foo_reg>; - aset-gpios = <&foo_gpio 1 GPIO_ACTIVE_LOW>; - capella,aset-resistance-ohms = <100000>; - interrupts = <1 IRQ_TYPE_EDGE_BOTH>; - io-channels = <&adc 0x01>; - io-channel-names = "aout"; -}; diff --git a/Documentation/devicetree/bindings/iio/light/cm36651.txt b/Documentation/devicetree/bindings/iio/light/cm36651.txt deleted file mode 100644 index c03e19db4550..000000000000 --- a/Documentation/devicetree/bindings/iio/light/cm36651.txt +++ /dev/null @@ -1,26 +0,0 @@ -* Capella CM36651 I2C Proximity and Color Light sensor - -Required properties: -- compatible: must be "capella,cm36651" -- reg: the I2C address of the device -- interrupts: interrupt-specifier for the sole interrupt - generated by the device -- vled-supply: regulator for the IR LED. IR_LED is a part - of the cm36651 for proximity detection. - As covered in ../../regulator/regulator.txt - -Example: - - i2c_cm36651: i2c-gpio { - /* ... */ - - cm36651@18 { - compatible = "capella,cm36651"; - reg = <0x18>; - interrupt-parent = <&gpx0>; - interrupts = <2 0>; - vled-supply = <&ps_als_reg>; - }; - - /* ... */ - }; diff --git a/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt b/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt deleted file mode 100644 index 9231c82317ad..000000000000 --- a/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt +++ /dev/null @@ -1,21 +0,0 @@ -* Sharp GP2AP020A00F I2C Proximity/ALS sensor - -The proximity detector sensor requires power supply -for its built-in led. It is also defined by this binding. - -Required properties: - - - compatible : should be "sharp,gp2ap020a00f" - - reg : the I2C slave address of the light sensor - - interrupts : interrupt specifier for the sole interrupt generated - by the device - - vled-supply : VLED power supply, as covered in ../regulator/regulator.txt - -Example: - -gp2ap020a00f@39 { - compatible = "sharp,gp2ap020a00f"; - reg = <0x39>; - interrupts = <2 0>; - vled-supply = <...>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/max44009.txt b/Documentation/devicetree/bindings/iio/light/max44009.txt deleted file mode 100644 index 4a98848e35c0..000000000000 --- a/Documentation/devicetree/bindings/iio/light/max44009.txt +++ /dev/null @@ -1,24 +0,0 @@ -* MAX44009 Ambient Light Sensor - -Required properties: - -- compatible: should be "maxim,max44009" -- reg: the I2C address of the device (default is <0x4a>) - -Optional properties: - -- interrupts: interrupt mapping for GPIO IRQ. Should be configured with - IRQ_TYPE_EDGE_FALLING. - -Refer to interrupt-controller/interrupts.txt for generic interrupt client -node bindings. - -Example: - -light-sensor@4a { - compatible = "maxim,max44009"; - reg = <0x4a>; - - interrupt-parent = <&gpio1>; - interrupts = <17 IRQ_TYPE_EDGE_FALLING>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/maxim,max44009.yaml b/Documentation/devicetree/bindings/iio/light/maxim,max44009.yaml new file mode 100644 index 000000000000..5911bd93bcb1 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/maxim,max44009.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/maxim,max44009.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MAX44009 Ambient Light Sensor + +maintainers: + - Robert Eshleman <bobbyeshleman@gmail.com> + +properties: + compatible: + const: maxim,max44009 + + reg: + maxItems: 1 + description: Default address is 0x4a + + interrupts: + maxItems: 1 + description: Should be configured with type IRQ_TYPE_EDGE_FALLING + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + light-sensor@4a { + compatible = "maxim,max44009"; + reg = <0x4a>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/opt3001.txt b/Documentation/devicetree/bindings/iio/light/opt3001.txt deleted file mode 100644 index 9e6f2998e751..000000000000 --- a/Documentation/devicetree/bindings/iio/light/opt3001.txt +++ /dev/null @@ -1,25 +0,0 @@ -* Texas Instruments OPT3001 Ambient Light Sensor - -The driver supports interrupt-driven and interrupt-less operation, depending -on whether an interrupt property has been populated into the DT. Note that -the optional generation of IIO events on rising/falling light threshold changes -requires the use of interrupts. Without interrupts, only the simple reading -of the current light value is supported through the IIO API. - -https://www.ti.com/product/opt3001 - -Required properties: - - compatible: should be "ti,opt3001" - - reg: the I2C address of the sensor - -Optional properties: - - interrupts: interrupt mapping for GPIO IRQ (configure for falling edge) - -Example: - -opt3001@44 { - compatible = "ti,opt3001"; - reg = <0x44>; - interrupt-parent = <&gpio1>; - interrupts = <28 IRQ_TYPE_EDGE_FALLING>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/renesas,isl29501.txt b/Documentation/devicetree/bindings/iio/light/renesas,isl29501.txt deleted file mode 100644 index 46957997fee3..000000000000 --- a/Documentation/devicetree/bindings/iio/light/renesas,isl29501.txt +++ /dev/null @@ -1,13 +0,0 @@ -* ISL29501 Time-of-flight sensor. - -Required properties: - - - compatible : should be "renesas,isl29501" - - reg : the I2C address of the sensor - -Example: - -isl29501@57 { - compatible = "renesas,isl29501"; - reg = <0x57>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/sharp,gp2ap020a00f.yaml b/Documentation/devicetree/bindings/iio/light/sharp,gp2ap020a00f.yaml new file mode 100644 index 000000000000..3fabf1f576cf --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/sharp,gp2ap020a00f.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/sharp,gp2ap020a00f.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sharp GP2AP020A00F I2C Proximity/ALS sensor + +maintainers: + - Kyungmin Park <kyungmin.park@samsung.com> + +description: | + The proximity detector sensor requires power supply for its built-in led. + +properties: + compatible: + const: sharp,gp2ap020a00f + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vled-supply: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - vled-supply + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + light-sensor@39 { + compatible = "sharp,gp2ap020a00f"; + reg = <0x39>; + interrupts = <2 0>; + vled-supply = <&als_reg>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/st,uvis25.yaml b/Documentation/devicetree/bindings/iio/light/st,uvis25.yaml new file mode 100644 index 000000000000..c86e5e1d135e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/st,uvis25.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/st,uvis25.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ST UVIS25 uv sensor + +maintainers: + - Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> + +properties: + compatible: + const: st,uvis25 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + uv-sensor@47 { + compatible = "st,uvis25"; + reg = <0x47>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/st,vl6180.yaml b/Documentation/devicetree/bindings/iio/light/st,vl6180.yaml new file mode 100644 index 000000000000..27c36ab7990d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/st,vl6180.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/st,vl6180.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicro VL6180 ALS, range and proximity sensor + +maintainers: + - Manivannan Sadhasivam <manivannanece23@gmail.com> + - Peter Meerwald-Stadler <pmeerw@pmeerw.net> + +description: | + Proximity sensing module incorporating time of flight sensor + Datasheet at https://www.st.com/resource/en/datasheet/vl6180x.pdf + +properties: + compatible: + const: st,vl6180 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + proximity@29 { + compatible = "st,vl6180"; + reg = <0x29>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/ti,opt3001.yaml b/Documentation/devicetree/bindings/iio/light/ti,opt3001.yaml new file mode 100644 index 000000000000..441e9343fc97 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/ti,opt3001.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/ti,opt3001.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments OPT3001 Ambient Light Sensor + +maintainers: + - Andreas Dannenberg <dannenberg@ti.com> + +description: | + The device supports interrupt-driven and interrupt-less operation, depending + on whether an interrupt property has been populated into the DT. + +properties: + compatible: + const: ti,opt3001 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + description: Should be configured with type IRQ_TYPE_EDGE_FALLING + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + light-sensor@44 { + compatible = "ti,opt3001"; + reg = <0x44>; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_EDGE_FALLING>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/upisemi,us5182.yaml b/Documentation/devicetree/bindings/iio/light/upisemi,us5182.yaml new file mode 100644 index 000000000000..4a9b2827cf7b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/upisemi,us5182.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/upisemi,us5182.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: UPISEMI us5182d I2C ALS and Proximity sensor + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +properties: + compatible: + const: upisemi,asd5182 + + reg: + maxItems: 1 + + upsemi,glass-coef: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + glass attenuation factor - compensation factor of resolution 1000 + for material transmittance. + default: 1000 + + upisemi,dark-ths: + $ref: /schemas/types.yaml#/definitions/uint16-array + minItems: 8 + maxItems: 8 + description: + 16-bit thresholds (adc counts) corresponding to every scale. + + upisemi,upper-dark-gain: + $ref: /schemas/types.yaml#/definitions/uint8 + description: | + 8-bit dark gain compensation factor(4 int and 4 fractional bits - Q4.4) + applied when light > threshold. + default: 0 + + upisemi,lower-dark-gain: + $ref: /schemas/types.yaml#/definitions/uint8 + description: | + 8-bit dark gain compensation factor(4 int and 4 fractional bits - Q4.4) + applied when light < threshold. + default: 0x16 + + upisemi,continuous: + $ref: /schemas/types.yaml#definitions/flag + description: | + This chip has two power modes: one-shot (chip takes one measurement and + then shuts itself down) and continuous (chip takes continuous + measurements). The one-shot mode is more power-friendly but the + continuous mode may be more reliable. If this property is specified + the continuous mode will be used instead of the default one-shot one for + raw reads. + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + light-sensor@39 { + compatible = "upisemi,usd5182"; + reg = <0x39>; + upisemi,glass-coef = < 1000 >; + upisemi,dark-ths = /bits/ 16 <170 200 512 512 800 2000 4000 8000>; + upisemi,upper-dark-gain = /bits/ 8 <0x00>; + upisemi,lower-dark-gain = /bits/ 8 <0x16>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/us5182d.txt b/Documentation/devicetree/bindings/iio/light/us5182d.txt deleted file mode 100644 index a61979997f37..000000000000 --- a/Documentation/devicetree/bindings/iio/light/us5182d.txt +++ /dev/null @@ -1,45 +0,0 @@ -* UPISEMI us5182d I2C ALS and Proximity sensor - -Required properties: -- compatible: must be "upisemi,usd5182" -- reg: the I2C address of the device - -Optional properties: -- upisemi,glass-coef: glass attenuation factor - compensation factor of - resolution 1000 for material transmittance. - -- upisemi,dark-ths: array of 8 elements containing 16-bit thresholds (adc - counts) corresponding to every scale. - -- upisemi,upper-dark-gain: 8-bit dark gain compensation factor(4 int and 4 - fractional bits - Q4.4) applied when light > threshold - -- upisemi,lower-dark-gain: 8-bit dark gain compensation factor(4 int and 4 - fractional bits - Q4.4) applied when light < threshold - -- upisemi,continuous: This chip has two power modes: one-shot (chip takes one - measurement and then shuts itself down) and continuous ( - chip takes continuous measurements). The one-shot mode is - more power-friendly but the continuous mode may be more - reliable. If this property is specified the continuous - mode will be used instead of the default one-shot one for - raw reads. - -If the optional properties are not specified these factors will default to the -values in the below example. -The glass-coef defaults to no compensation for the covering material. -The threshold array defaults to experimental values that work with US5182D -sensor on evaluation board - roughly between 12-32 lux. -There will be no dark-gain compensation by default when ALS > thresh -(0 * dark-gain), and a 1.35 compensation factor when ALS < thresh. - -Example: - - usd5182@39 { - compatible = "upisemi,usd5182"; - reg = <0x39>; - upisemi,glass-coef = < 1000 >; - upisemi,dark-ths = /bits/ 16 <170 200 512 512 800 2000 4000 8000>; - upisemi,upper-dark-gain = /bits/ 8 <0x00>; - upisemi,lower-dark-gain = /bits/ 8 <0x16>; - }; diff --git a/Documentation/devicetree/bindings/iio/light/uvis25.txt b/Documentation/devicetree/bindings/iio/light/uvis25.txt deleted file mode 100644 index 043c139d91e6..000000000000 --- a/Documentation/devicetree/bindings/iio/light/uvis25.txt +++ /dev/null @@ -1,22 +0,0 @@ -* ST UVIS25 uv sensor - -Required properties: -- compatible: should be "st,uvis25" -- reg: i2c address of the sensor / spi cs line - -Optional properties: -- interrupts: interrupt mapping for IRQ. It should be configured with - flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or - IRQ_TYPE_EDGE_FALLING. - - Refer to interrupt-controller/interrupts.txt for generic interrupt - client node bindings. - -Example: - -uvis25@47 { - compatible = "st,uvis25"; - reg = <0x47>; - interrupt-parent = <&gpio0>; - interrupts = <0 IRQ_TYPE_EDGE_RISING>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/vcnl4035.txt b/Documentation/devicetree/bindings/iio/light/vcnl4035.txt deleted file mode 100644 index c07c7f052556..000000000000 --- a/Documentation/devicetree/bindings/iio/light/vcnl4035.txt +++ /dev/null @@ -1,18 +0,0 @@ -VISHAY VCNL4035 - Ambient Light and proximity sensor - -Link to datasheet: https://www.vishay.com/docs/84251/vcnl4035x01.pdf - -Required properties: - - -compatible: should be "vishay,vcnl4035" - -reg: I2C address of the sensor, should be 0x60 - -interrupts: interrupt mapping for GPIO IRQ (level active low) - -Example: - -light-sensor@60 { - compatible = "vishay,vcnl4035"; - reg = <0x60>; - interrupt-parent = <&gpio4>; - interrupts = <11 IRQ_TYPE_LEVEL_LOW>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/vishay,vcnl4035.yaml b/Documentation/devicetree/bindings/iio/light/vishay,vcnl4035.yaml new file mode 100644 index 000000000000..2c57ff05de15 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/vishay,vcnl4035.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/vishay,vcnl4035.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: VISHAY VCNL4035 ambient Light and proximity sensor + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: | + Datasheet at https://www.vishay.com/docs/84251/vcnl4035x01.pdf + +properties: + compatible: + const: vishay,vcnl4035 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + light-sensor@60 { + compatible = "vishay,vcnl4035"; + reg = <0x60>; + interrupt-parent = <&gpio4>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/vl6180.txt b/Documentation/devicetree/bindings/iio/light/vl6180.txt deleted file mode 100644 index fb9137d85df9..000000000000 --- a/Documentation/devicetree/bindings/iio/light/vl6180.txt +++ /dev/null @@ -1,15 +0,0 @@ -STMicro VL6180 - ALS, range and proximity sensor - -Link to datasheet: https://www.st.com/resource/en/datasheet/vl6180x.pdf - -Required properties: - - -compatible: should be "st,vl6180" - -reg: the I2C address of the sensor - -Example: - -vl6180@29 { - compatible = "st,vl6180"; - reg = <0x29>; -}; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt b/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt deleted file mode 100644 index 7f06eff3b504..000000000000 --- a/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt +++ /dev/null @@ -1,31 +0,0 @@ -* Asahi Kasei AK8974 magnetometer sensor - -Required properties: - -- compatible: - * "asahi-kasei,ak8974" - * "alps,hscdtd008a" -- reg : the I2C address of the magnetometer - -Optional properties: - -- avdd-supply: regulator supply for the analog voltage - (see regulator/regulator.txt) -- dvdd-supply: regulator supply for the digital voltage - (see regulator/regulator.txt) -- interrupts: data ready (DRDY) and interrupt (INT1) lines - from the chip, the DRDY interrupt must be placed first. - The interrupts can be triggered on rising or falling - edges alike. -- mount-matrix: an optional 3x3 mounting rotation matrix - -Example: - -ak8974@f { - compatible = "asahi-kasei,ak8974"; - reg = <0x0f>; - avdd-supply = <&foo_reg>; - dvdd-supply = <&bar_reg>; - interrupts = <0 IRQ_TYPE_EDGE_RISING>, - <1 IRQ_TYPE_EDGE_RISING>; -}; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8974.yaml b/Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8974.yaml new file mode 100644 index 000000000000..cefb70def188 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8974.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/magnetometer/asahi-kasei,ak8974.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Asahi Kasei AK8974 magnetometer sensor + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +properties: + compatible: + enum: + - alps,hscdtd008a + - asahi-kasei,ak8974 + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + description: | + Data ready (DRDY) and interrupt (INT1) lines from the chip. The DRDY + interrupt must be placed first. The interrupts can be triggered on + rising or falling edges. + + avdd-supply: true + + dvdd-supply: true + + mount-matrix: true + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + magnetometer@f { + compatible = "asahi-kasei,ak8974"; + reg = <0x0f>; + avdd-supply = <&foo_reg>; + dvdd-supply = <&bar_reg>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>, + <1 IRQ_TYPE_EDGE_RISING>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/magnetometer/bmc150_magn.txt b/Documentation/devicetree/bindings/iio/magnetometer/bmc150_magn.txt deleted file mode 100644 index 22912e43b60c..000000000000 --- a/Documentation/devicetree/bindings/iio/magnetometer/bmc150_magn.txt +++ /dev/null @@ -1,25 +0,0 @@ -* Bosch BMC150 magnetometer sensor - -http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-04.pdf - -Required properties: - - - compatible : should be one of: - "bosch,bmc150_magn" - "bosch,bmc156_magn" - "bosch,bmm150" - "bosch,bmm150_magn" (DEPRECATED, use bosch,bmm150) - - reg : the I2C address of the magnetometer - -Optional properties: - - - interrupts : interrupt mapping for GPIO IRQ - -Example: - -bmc150_magn@12 { - compatible = "bosch,bmc150_magn"; - reg = <0x12>; - interrupt-parent = <&gpio1>; - interrupts = <0 1>; -}; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/bosch,bmc150_magn.yaml b/Documentation/devicetree/bindings/iio/magnetometer/bosch,bmc150_magn.yaml new file mode 100644 index 000000000000..cdef7aeba708 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/magnetometer/bosch,bmc150_magn.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/magnetometer/bosch,bmc150_magn.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bosch BMC150 magnetometer sensor + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: | + Supports a range of parts, some of which form part of a multi die + package that also contains other sensors. The interface is independent + however, so a separate driver is used to support the magnetometer part. + Datasheet at: + http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-04.pdf + +properties: + compatible: + description: + Note the bmm150_magn is a deprecated compatible as this part contains only + a magnetometer. + enum: + - bosch,bmc150_magn + - bosch,bmc156_magn + - bosch,bmm150 + - bosch,bmm150_magn + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + magnetometer@12 { + compatible = "bosch,bmc150_magn"; + reg = <0x12>; + interrupt-parent = <&gpio1>; + interrupts = <0 1>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/magnetometer/fsl,mag3110.yaml b/Documentation/devicetree/bindings/iio/magnetometer/fsl,mag3110.yaml new file mode 100644 index 000000000000..6b54d32323fc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/magnetometer/fsl,mag3110.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/magnetometer/fsl,mag3110.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale MAG3110 magnetometer sensor + +maintainers: + - Anson Huang <Anson.Huang@nxp.com> + +properties: + compatible: + const: fsl,mag3110 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vdd-supply: true + + vddio-supply: true + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + magnetometer@e { + compatible = "fsl,mag3110"; + reg = <0x0e>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3_mag3110_int>; + interrupt-parent = <&gpio3>; + interrupts = <16 IRQ_TYPE_EDGE_RISING>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt b/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt deleted file mode 100644 index 8e191eef014e..000000000000 --- a/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt +++ /dev/null @@ -1,21 +0,0 @@ -* Honeywell HMC5843 magnetometer sensor - -Required properties: - - - compatible : should be "honeywell,hmc5843" - Other models which are supported with driver are: - "honeywell,hmc5883" - "honeywell,hmc5883l" - "honeywell,hmc5983" - - reg : the I2C address of the magnetometer - typically 0x1e - -Optional properties: - - - gpios : should be device tree identifier of the magnetometer DRDY pin - -Example: - -hmc5843@1e { - compatible = "honeywell,hmc5843" - reg = <0x1e>; -}; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/honeywell,hmc5843.yaml b/Documentation/devicetree/bindings/iio/magnetometer/honeywell,hmc5843.yaml new file mode 100644 index 000000000000..5e778c98584e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/magnetometer/honeywell,hmc5843.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/magnetometer/honeywell,hmc5843.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Honeywell HMC5843 magnetometer sensor + +maintainers: + - Neil Brown <neilb@suse.de> + +properties: + compatible: + enum: + - honeywell,hmc5843 + - honeywell,hmc5883 + - honeywell,hmc5883l + - honeywell,hmc5983 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + magnetometer@1e { + compatible = "honeywell,hmc5843"; + reg = <0x1e>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/magnetometer/mag3110.txt b/Documentation/devicetree/bindings/iio/magnetometer/mag3110.txt deleted file mode 100644 index bdd40bcaaa1f..000000000000 --- a/Documentation/devicetree/bindings/iio/magnetometer/mag3110.txt +++ /dev/null @@ -1,27 +0,0 @@ -* FREESCALE MAG3110 magnetometer sensor - -Required properties: - - - compatible : should be "fsl,mag3110" - - reg : the I2C address of the magnetometer - -Optional properties: - - - interrupts: the sole interrupt generated by the device - - Refer to interrupt-controller/interrupts.txt for generic interrupt client - node bindings. - - - vdd-supply: phandle to the regulator that provides power to the sensor. - - vddio-supply: phandle to the regulator that provides power to the sensor's IO. - -Example: - -magnetometer@e { - compatible = "fsl,mag3110"; - reg = <0x0e>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3_mag3110_int>; - interrupt-parent = <&gpio3>; - interrupts = <16 IRQ_TYPE_EDGE_RISING>; -}; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/mmc35240.txt b/Documentation/devicetree/bindings/iio/magnetometer/mmc35240.txt deleted file mode 100644 index a01235c7fa15..000000000000 --- a/Documentation/devicetree/bindings/iio/magnetometer/mmc35240.txt +++ /dev/null @@ -1,13 +0,0 @@ -* MEMSIC MMC35240 magnetometer sensor - -Required properties: - - - compatible : should be "memsic,mmc35240" - - reg : the I2C address of the magnetometer - -Example: - -mmc35240@30 { - compatible = "memsic,mmc35240"; - reg = <0x30>; -}; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.txt b/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.txt deleted file mode 100644 index 497c932e9e39..000000000000 --- a/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.txt +++ /dev/null @@ -1,20 +0,0 @@ -* PNI RM3100 3-axis magnetometer sensor - -Required properties: - -- compatible : should be "pni,rm3100" -- reg : the I2C address or SPI chip select number of the sensor. - -Optional properties: - -- interrupts: data ready (DRDY) from the chip. - The interrupts can be triggered on level high. - -Example: - -rm3100: rm3100@20 { - compatible = "pni,rm3100"; - reg = <0x20>; - interrupt-parent = <&gpio0>; - interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; -}; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.yaml b/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.yaml new file mode 100644 index 000000000000..a845cdd23e7b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/magnetometer/pni,rm3100.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: PNI RM3100 3-axis magnetometer sensor + +maintainers: + - Song Qiang <songqiang1304521@gmail.com> + +properties: + compatible: + const: pni,rm3100 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + magnetometer@20 { + compatible = "pni,rm3100"; + reg = <0x20>; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/potentiometer/ad5272.txt b/Documentation/devicetree/bindings/iio/potentiometer/ad5272.txt deleted file mode 100644 index f9b2eef946aa..000000000000 --- a/Documentation/devicetree/bindings/iio/potentiometer/ad5272.txt +++ /dev/null @@ -1,27 +0,0 @@ -* Analog Devices AD5272 digital potentiometer - -The node for this device must be a child node of a I2C controller, hence -all mandatory properties for your controller must be specified. See directory: - - Documentation/devicetree/bindings/i2c - -for more details. - -Required properties: - - compatible: Must be one of the following, depending on the model: - adi,ad5272-020 - adi,ad5272-050 - adi,ad5272-100 - adi,ad5274-020 - adi,ad5274-100 - -Optional properties: - - reset-gpios: GPIO specification for the RESET input. This is an - active low signal to the AD5272. - -Example: -ad5272: potentiometer@2f { - reg = <0x2F>; - compatible = "adi,ad5272-020"; - reset-gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>; -}; diff --git a/Documentation/devicetree/bindings/iio/potentiometer/adi,ad5272.yaml b/Documentation/devicetree/bindings/iio/potentiometer/adi,ad5272.yaml new file mode 100644 index 000000000000..1aee9f9be951 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiometer/adi,ad5272.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/potentiometer/adi,ad5272.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD5272 digital potentiometer + +maintainers: + - Phil Reid <preid@electromag.com.au> + +description: | + Datasheet: https://www.analog.com/en/products/ad5272.html + +properties: + compatible: + enum: + - adi,ad5272-020 + - adi,ad5272-050 + - adi,ad5272-100 + - adi,ad5274-020 + - adi,ad5274-100 + + reg: + maxItems: 1 + + reset-gpios: + description: + Active low signal to the AD5272 RESET input. + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + potentiometer@2f { + compatible = "adi,ad5272-020"; + reg = <0x2F>; + reset-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/potentiometer/ds1803.txt b/Documentation/devicetree/bindings/iio/potentiometer/ds1803.txt deleted file mode 100644 index df77bf552656..000000000000 --- a/Documentation/devicetree/bindings/iio/potentiometer/ds1803.txt +++ /dev/null @@ -1,21 +0,0 @@ -* Maxim Integrated DS1803 digital potentiometer driver - -The node for this driver must be a child node of a I2C controller, hence -all mandatory properties for your controller must be specified. See directory: - - Documentation/devicetree/bindings/i2c - -for more details. - -Required properties: - - compatible: Must be one of the following, depending on the - model: - "maxim,ds1803-010", - "maxim,ds1803-050", - "maxim,ds1803-100" - -Example: -ds1803: ds1803@1 { - reg = <0x28>; - compatible = "maxim,ds1803-010"; -}; diff --git a/Documentation/devicetree/bindings/iio/potentiometer/max5481.txt b/Documentation/devicetree/bindings/iio/potentiometer/max5481.txt deleted file mode 100644 index 6a91b106e076..000000000000 --- a/Documentation/devicetree/bindings/iio/potentiometer/max5481.txt +++ /dev/null @@ -1,23 +0,0 @@ -* Maxim Linear-Taper Digital Potentiometer MAX5481-MAX5484 - -The node for this driver must be a child node of a SPI controller, hence -all mandatory properties described in - - Documentation/devicetree/bindings/spi/spi-bus.txt - -must be specified. - -Required properties: - - compatible: Must be one of the following, depending on the - model: - "maxim,max5481" - "maxim,max5482" - "maxim,max5483" - "maxim,max5484" - -Example: -max548x: max548x@0 { - compatible = "maxim,max5482"; - spi-max-frequency = <7000000>; - reg = <0>; /* chip-select */ -}; diff --git a/Documentation/devicetree/bindings/iio/potentiometer/mcp41010.txt b/Documentation/devicetree/bindings/iio/potentiometer/mcp41010.txt deleted file mode 100644 index 4f245e8469fd..000000000000 --- a/Documentation/devicetree/bindings/iio/potentiometer/mcp41010.txt +++ /dev/null @@ -1,28 +0,0 @@ -* Microchip MCP41010/41050/41100/42010/42050/42100 Digital Potentiometer - -Datasheet publicly available at: -https://ww1.microchip.com/downloads/en/devicedoc/11195c.pdf - -The node for this driver must be a child node of a SPI controller, hence -all mandatory properties described in - - Documentation/devicetree/bindings/spi/spi-bus.txt - -must be specified. - -Required properties: - - compatible: Must be one of the following, depending on the - model: - "microchip,mcp41010" - "microchip,mcp41050" - "microchip,mcp41100" - "microchip,mcp42010" - "microchip,mcp42050" - "microchip,mcp42100" - -Example: -potentiometer@0 { - compatible = "microchip,mcp41010"; - reg = <0>; - spi-max-frequency = <500000>; -}; diff --git a/Documentation/devicetree/bindings/iio/potentiometer/mcp4131.txt b/Documentation/devicetree/bindings/iio/potentiometer/mcp4131.txt deleted file mode 100644 index 3ccba16f7035..000000000000 --- a/Documentation/devicetree/bindings/iio/potentiometer/mcp4131.txt +++ /dev/null @@ -1,84 +0,0 @@ -* Microchip MCP413X/414X/415X/416X/423X/424X/425X/426X Digital Potentiometer - driver - -The node for this driver must be a child node of a SPI controller, hence -all mandatory properties described in - - Documentation/devicetree/bindings/spi/spi-bus.txt - -must be specified. - -Required properties: - - compatible: Must be one of the following, depending on the - model: - "microchip,mcp4131-502" - "microchip,mcp4131-103" - "microchip,mcp4131-503" - "microchip,mcp4131-104" - "microchip,mcp4132-502" - "microchip,mcp4132-103" - "microchip,mcp4132-503" - "microchip,mcp4132-104" - "microchip,mcp4141-502" - "microchip,mcp4141-103" - "microchip,mcp4141-503" - "microchip,mcp4141-104" - "microchip,mcp4142-502" - "microchip,mcp4142-103" - "microchip,mcp4142-503" - "microchip,mcp4142-104" - "microchip,mcp4151-502" - "microchip,mcp4151-103" - "microchip,mcp4151-503" - "microchip,mcp4151-104" - "microchip,mcp4152-502" - "microchip,mcp4152-103" - "microchip,mcp4152-503" - "microchip,mcp4152-104" - "microchip,mcp4161-502" - "microchip,mcp4161-103" - "microchip,mcp4161-503" - "microchip,mcp4161-104" - "microchip,mcp4162-502" - "microchip,mcp4162-103" - "microchip,mcp4162-503" - "microchip,mcp4162-104" - "microchip,mcp4231-502" - "microchip,mcp4231-103" - "microchip,mcp4231-503" - "microchip,mcp4231-104" - "microchip,mcp4232-502" - "microchip,mcp4232-103" - "microchip,mcp4232-503" - "microchip,mcp4232-104" - "microchip,mcp4241-502" - "microchip,mcp4241-103" - "microchip,mcp4241-503" - "microchip,mcp4241-104" - "microchip,mcp4242-502" - "microchip,mcp4242-103" - "microchip,mcp4242-503" - "microchip,mcp4242-104" - "microchip,mcp4251-502" - "microchip,mcp4251-103" - "microchip,mcp4251-503" - "microchip,mcp4251-104" - "microchip,mcp4252-502" - "microchip,mcp4252-103" - "microchip,mcp4252-503" - "microchip,mcp4252-104" - "microchip,mcp4261-502" - "microchip,mcp4261-103" - "microchip,mcp4261-503" - "microchip,mcp4261-104" - "microchip,mcp4262-502" - "microchip,mcp4262-103" - "microchip,mcp4262-503" - "microchip,mcp4262-104" - -Example: -mcp4131: mcp4131@0 { - compatible = "mcp4131-502"; - reg = <0>; - spi-max-frequency = <500000>; -}; diff --git a/Documentation/devicetree/bindings/iio/potentiometer/microchip,mcp41010.yaml b/Documentation/devicetree/bindings/iio/potentiometer/microchip,mcp41010.yaml new file mode 100644 index 000000000000..567697d996ec --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiometer/microchip,mcp41010.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/potentiometer/microchip,mcp41010.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip MCP41010/41050/41100/42010/42050/42100 Digital Potentiometer + +maintainers: + - Chris Coffey <cmc@babblebit.net> + +description: | + Datasheet: https://ww1.microchip.com/downloads/en/devicedoc/11195c.pdf + +properties: + compatible: + enum: + - microchip,mcp41010 + - microchip,mcp41050 + - microchip,mcp41100 + - microchip,mcp42010 + - microchip,mcp42050 + - microchip,mcp42100 + + reg: + maxItems: 1 + + spi-max-frequency: true + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + potentiometer@0 { + compatible = "microchip,mcp41010"; + reg = <0>; + spi-max-frequency = <500000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/potentiometer/microchip,mcp4131.yaml b/Documentation/devicetree/bindings/iio/potentiometer/microchip,mcp4131.yaml new file mode 100644 index 000000000000..945a2d644ddc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiometer/microchip,mcp4131.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/potentiometer/microchip,mcp4131.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip MCP413X/414X/415X/416X/423X/424X/425X/426X Digital Potentiometer + +maintainers: + - Slawomir Stepien <sst@poczta.fm> + +properties: + compatible: + enum: + - microchip,mcp4131-103 + - microchip,mcp4131-104 + - microchip,mcp4131-502 + - microchip,mcp4131-503 + - microchip,mcp4132-103 + - microchip,mcp4132-104 + - microchip,mcp4132-502 + - microchip,mcp4132-503 + - microchip,mcp4141-103 + - microchip,mcp4141-104 + - microchip,mcp4141-502 + - microchip,mcp4141-503 + - microchip,mcp4142-103 + - microchip,mcp4142-104 + - microchip,mcp4142-502 + - microchip,mcp4142-503 + - microchip,mcp4151-103 + - microchip,mcp4151-104 + - microchip,mcp4151-502 + - microchip,mcp4151-503 + - microchip,mcp4152-103 + - microchip,mcp4152-104 + - microchip,mcp4152-502 + - microchip,mcp4152-503 + - microchip,mcp4161-103 + - microchip,mcp4161-104 + - microchip,mcp4161-502 + - microchip,mcp4161-503 + - microchip,mcp4162-103 + - microchip,mcp4162-104 + - microchip,mcp4162-502 + - microchip,mcp4162-503 + - microchip,mcp4231-103 + - microchip,mcp4231-104 + - microchip,mcp4231-502 + - microchip,mcp4231-503 + - microchip,mcp4232-103 + - microchip,mcp4232-104 + - microchip,mcp4232-502 + - microchip,mcp4232-503 + - microchip,mcp4241-103 + - microchip,mcp4241-104 + - microchip,mcp4241-502 + - microchip,mcp4241-503 + - microchip,mcp4242-103 + - microchip,mcp4242-104 + - microchip,mcp4242-502 + - microchip,mcp4242-503 + - microchip,mcp4251-103 + - microchip,mcp4251-104 + - microchip,mcp4251-502 + - microchip,mcp4251-503 + - microchip,mcp4252-103 + - microchip,mcp4252-104 + - microchip,mcp4252-502 + - microchip,mcp4252-503 + - microchip,mcp4261-103 + - microchip,mcp4261-104 + - microchip,mcp4261-502 + - microchip,mcp4261-503 + - microchip,mcp4262-103 + - microchip,mcp4262-104 + - microchip,mcp4262-502 + - microchip,mcp4262-503 + + reg: + maxItems: 1 + + spi-max-frequency: true + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + potentiometer@0 { + compatible = "mcp4131-502"; + reg = <0>; + spi-max-frequency = <500000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/potentiometer/microchip,mcp4531.yaml b/Documentation/devicetree/bindings/iio/potentiometer/microchip,mcp4531.yaml new file mode 100644 index 000000000000..5c4b9b9181ae --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiometer/microchip,mcp4531.yaml @@ -0,0 +1,116 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/potentiometer/microchip,mcp4531.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip mcp4531 and similar potentiometers. + +maintainers: + - Peter Rosin <peda@axentia.se> + +description: | + Family of I2C digital potentiometer + Datasheets at: + * volatile https://ww1.microchip.com/downloads/en/DeviceDoc/22096b.pdf + * non-volatile https://ww1.microchip.com/downloads/en/DeviceDoc/22107B.pdf + Part numbers as follows: mcp4ABC-XXX where + A = 5 (1 wiper), 6 (2 wipers) + B = 3 (7-bit, volatile), 4 (7-bit, non-volatile), + 5 (8-bit, volatile), 6 (8-bit, non-volatile), + C: 1 (potentiometer), 2 (rheostat) + XXX = 502 (5 kOhms), 103 (10 kOhms), 503 (50 kOhms), 104 (100 kOhms) + +properties: + compatible: + enum: + # Ordering reflects part number + range, so 502 < 103 etc + - microchip,mcp4531-502 + - microchip,mcp4531-103 + - microchip,mcp4531-503 + - microchip,mcp4531-104 + - microchip,mcp4532-502 + - microchip,mcp4532-103 + - microchip,mcp4532-503 + - microchip,mcp4532-104 + - microchip,mcp4541-502 + - microchip,mcp4541-103 + - microchip,mcp4541-503 + - microchip,mcp4541-104 + - microchip,mcp4542-502 + - microchip,mcp4542-103 + - microchip,mcp4542-503 + - microchip,mcp4542-104 + - microchip,mcp4551-502 + - microchip,mcp4551-103 + - microchip,mcp4551-503 + - microchip,mcp4551-104 + - microchip,mcp4552-502 + - microchip,mcp4552-103 + - microchip,mcp4552-503 + - microchip,mcp4552-104 + - microchip,mcp4561-502 + - microchip,mcp4561-103 + - microchip,mcp4561-503 + - microchip,mcp4561-104 + - microchip,mcp4562-502 + - microchip,mcp4562-103 + - microchip,mcp4562-503 + - microchip,mcp4562-104 + - microchip,mcp4631-502 + - microchip,mcp4631-103 + - microchip,mcp4631-503 + - microchip,mcp4631-104 + - microchip,mcp4632-502 + - microchip,mcp4632-103 + - microchip,mcp4632-503 + - microchip,mcp4632-104 + - microchip,mcp4641-502 + - microchip,mcp4641-103 + - microchip,mcp4641-503 + - microchip,mcp4641-104 + - microchip,mcp4642-502 + - microchip,mcp4642-103 + - microchip,mcp4642-503 + - microchip,mcp4642-104 + - microchip,mcp4651-502 + - microchip,mcp4651-103 + - microchip,mcp4651-503 + - microchip,mcp4651-104 + - microchip,mcp4652-502 + - microchip,mcp4652-103 + - microchip,mcp4652-503 + - microchip,mcp4652-104 + - microchip,mcp4661-502 + - microchip,mcp4661-103 + - microchip,mcp4661-503 + - microchip,mcp4661-104 + - microchip,mcp4662-502 + - microchip,mcp4662-103 + - microchip,mcp4662-503 + - microchip,mcp4662-104 + + reg: + maxItems: 1 + + "#io-channel-cells": + const: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + dpot: dpot@28 { + compatible = "microchip,mcp4651-104"; + reg = <0x28>; + #io-channel-cells = <1>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt deleted file mode 100644 index f3ab02b0dd41..000000000000 --- a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt +++ /dev/null @@ -1,33 +0,0 @@ -* Texas Instruments LMP91000 series of potentiostats - -LMP91000: https://www.ti.com/lit/ds/symlink/lmp91000.pdf -LMP91002: https://www.ti.com/lit/ds/symlink/lmp91002.pdf - -Required properties: - - - compatible: should be one of the following: - "ti,lmp91000" - "ti,lmp91002" - - reg: the I2C address of the device - - io-channels: the phandle of the iio provider - - - ti,external-tia-resistor: if the property ti,tia-gain-ohm is not defined this - needs to be set to signal that an external resistor value is being used. - -Optional properties: - - - ti,tia-gain-ohm: ohm value of the internal resistor for the transimpedance - amplifier. Must be 2750, 3500, 7000, 14000, 35000, 120000, or 350000 ohms. - - - ti,rload-ohm: ohm value of the internal resistor load applied to the gas - sensor. Must be 10, 33, 50, or 100 (default) ohms. - -Example: - -lmp91000@48 { - compatible = "ti,lmp91000"; - reg = <0x48>; - ti,tia-gain-ohm = <7500>; - ti,rload = <100>; - io-channels = <&adc>; -}; diff --git a/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml b/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml new file mode 100644 index 000000000000..e4b5d890e8d5 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/potentiostat/ti,lmp91000.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments LMP91000 series of potentiostats with I2C control + +maintainers: + - Matt Ranostay <matt.ranostay@konsulko.com> + +description: | + Typically used as a signal conditioner for chemical sensors. + LMP91000: https://www.ti.com/lit/ds/symlink/lmp91000.pdf + LMP91002: https://www.ti.com/lit/ds/symlink/lmp91002.pdf + +properties: + compatible: + enum: + - ti,lmp91000 + - ti,lmp91002 + + reg: + maxItems: 1 + + io-channels: + maxItems: 1 + + ti,external-tia-resistor: + $ref: /schemas/types.yaml#/definitions/flag + description: + If the property ti,tia-gain-ohm is not defined this needs to be set to + signal that an external resistor value is being used. + + ti,tia-gain-ohm: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [2750, 3500, 7000, 14000, 35000, 120000, 350000] + description: + Internal resistor for the transimpedance amplifier. + + ti,rload-ohm: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [10, 33, 50, 100] + description: + Internal resistor load applied to the gas sensor. + Default 100 Ohms. + +required: + - compatible + - reg + - io-channels + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + lmp91000@48 { + compatible = "ti,lmp91000"; + reg = <0x48>; + ti,tia-gain-ohm = <7000>; + ti,rload-ohm = <100>; + io-channels = <&adc>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml b/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml new file mode 100644 index 000000000000..69a3759e23db --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/pressure/hoperf,hp03.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HopeRF HP03 digital pressure/temperature sensors + +maintainers: + - Marek Vasut <marex@denx.de> + +description: | + Digital pressure and temperature sensor with an I2C interface. + +properties: + compatible: + const: hoperf,hp03 + + reg: + maxItems: 1 + + xclr-gpios: + description: + The XCLR pin is a reset of the ADC in the chip, it must be pulled + HI before the conversion and readout of the value from the ADC + registers and pulled LO afterward. + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pressure@77 { + compatible = "hoperf,hp03"; + reg = <0x77>; + xclr-gpios = <&portc 0 0x0>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/pressure/hp03.txt b/Documentation/devicetree/bindings/iio/pressure/hp03.txt deleted file mode 100644 index 831dbee7a5c3..000000000000 --- a/Documentation/devicetree/bindings/iio/pressure/hp03.txt +++ /dev/null @@ -1,17 +0,0 @@ -HopeRF HP03 digital pressure/temperature sensors - -Required properties: -- compatible: must be "hoperf,hp03" -- xclr-gpio: must be device tree identifier of the XCLR pin. - The XCLR pin is a reset of the ADC in the chip, - it must be pulled HI before the conversion and - readout of the value from the ADC registers and - pulled LO afterward. - -Example: - -hp03@77 { - compatible = "hoperf,hp03"; - reg = <0x77>; - xclr-gpio = <&portc 0 0x0>; -}; diff --git a/Documentation/devicetree/bindings/iio/pressure/meas,ms5611.yaml b/Documentation/devicetree/bindings/iio/pressure/meas,ms5611.yaml new file mode 100644 index 000000000000..4f06707450bf --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/meas,ms5611.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/pressure/meas,ms5611.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Measurement Specialities ms5611 and similar pressure sensors + +maintainers: + - Tomasz Duszynski <tduszyns@gmail.com> + +description: | + Pressure sensors from MEAS Switzerland with SPI and I2C bus interfaces. + +properties: + compatible: + enum: + - meas,ms5607 + - meas,ms5611 + + reg: + maxItems: 1 + + vdd-supply: true + + spi-max-frequency: + maximum: 20000000 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pressure@77 { + compatible = "meas,ms5607"; + reg = <0x77>; + vdd-supply = <&ldo_3v3_gnss>; + }; + }; + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + pressure@0 { + compatible = "meas,ms5611"; + reg = <0>; + vdd-supply = <&ldo_3v3_gnss>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/pressure/ms5611.txt b/Documentation/devicetree/bindings/iio/pressure/ms5611.txt deleted file mode 100644 index 17bca866c084..000000000000 --- a/Documentation/devicetree/bindings/iio/pressure/ms5611.txt +++ /dev/null @@ -1,19 +0,0 @@ -MEAS ms5611 family pressure sensors - -Pressure sensors from MEAS Switzerland with SPI and I2C bus interfaces. - -Required properties: -- compatible: "meas,ms5611" or "meas,ms5607" -- reg: the I2C address or SPI chip select the device will respond to - -Optional properties: -- vdd-supply: an optional regulator that needs to be on to provide VDD - power to the sensor. - -Example: - -ms5607@77 { - compatible = "meas,ms5607"; - reg = <0x77>; - vdd-supply = <&ldo_3v3_gnss>; -}; diff --git a/Documentation/devicetree/bindings/iio/pressure/ms5637.txt b/Documentation/devicetree/bindings/iio/pressure/ms5637.txt deleted file mode 100644 index 1f43ffa068ac..000000000000 --- a/Documentation/devicetree/bindings/iio/pressure/ms5637.txt +++ /dev/null @@ -1,17 +0,0 @@ -* MS5637 - Measurement-Specialties MS5637, MS5805, MS5837 and MS8607 pressure & temperature sensor - -Required properties: - - -compatible: should be one of the following - meas,ms5637 - meas,ms5805 - meas,ms5837 - meas,ms8607-temppressure - -reg: I2C address of the sensor - -Example: - -ms5637@76 { - compatible = "meas,ms5637"; - reg = <0x76>; -}; diff --git a/Documentation/devicetree/bindings/iio/pressure/murata,zpa2326.yaml b/Documentation/devicetree/bindings/iio/pressure/murata,zpa2326.yaml new file mode 100644 index 000000000000..d6103be03460 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/murata,zpa2326.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/pressure/murata,zpa2326.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Murata ZPA2326 pressure sensor + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: | + Pressure sensor from Murata with SPI and I2C bus interfaces. + + +properties: + compatible: + const: murata,zpa2326 + + reg: + maxItems: 1 + + vdd-supply: true + vref-supply: true + + interrupts: + maxItems: 1 + + spi-max-frequency: + maximum: 1000000 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pressure@5c { + compatible = "murata,zpa2326"; + reg = <0x5c>; + interrupt-parent = <&gpio>; + interrupts = <12>; + vdd-supply = <&ldo_1v8_gnss>; + }; + }; + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + pressure@0 { + compatible = "murata,zpa2326"; + reg = <0>; + spi-max-frequency = <500000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt b/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt deleted file mode 100644 index a36ab3e0c3f7..000000000000 --- a/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt +++ /dev/null @@ -1,29 +0,0 @@ -Murata ZPA2326 pressure sensor - -Pressure sensor from Murata with SPI and I2C bus interfaces. - -Required properties: -- compatible: "murata,zpa2326" -- reg: the I2C address or SPI chip select the device will respond to - -Recommended properties for SPI bus usage: -- spi-max-frequency: maximum SPI bus frequency as documented in - Documentation/devicetree/bindings/spi/spi-bus.txt - -Optional properties: -- vref-supply: an optional regulator that needs to be on to provide VREF - power to the sensor -- vdd-supply: an optional regulator that needs to be on to provide VDD - power to the sensor -- interrupts: interrupt mapping for IRQ as documented in - Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - -Example: - -zpa2326@5c { - compatible = "murata,zpa2326"; - reg = <0x5c>; - interrupt-parent = <&gpio>; - interrupts = <12>; - vdd-supply = <&ldo_1v8_gnss>; -}; diff --git a/Documentation/devicetree/bindings/iio/proximity/ams,as3935.yaml b/Documentation/devicetree/bindings/iio/proximity/ams,as3935.yaml new file mode 100644 index 000000000000..7fcba5d6d508 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/ams,as3935.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/proximity/ams,as3935.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Austrian Microsystems AS3935 Franklin lightning sensor + +maintainers: + - Matt Ranostay <matt.ranostay@konsulko.com> + +description: + This lightening distance sensor uses an I2C or SPI interface. The + binding currently only covers the SPI option. + +properties: + compatible: + const: ams,as3935 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 2000000 + + spi-cpha: true + + interrupts: + maxItems: 1 + + ams,tuning-capacitor-pf: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Calibration tuning capacitor stepping value. This will require using + the calibration data from the manufacturer. + minimum: 0 + maximum: 120 + + ams,nflwdth: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Set the noise and watchdog threshold register on startup. This will + need to set according to the noise from the MCU board, and possibly + the local environment. Refer to the datasheet for the threshold settings. + +required: + - compatible + - reg + - spi-cpha + - interrupts + +additionalProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + lightning@0 { + compatible = "ams,as3935"; + reg = <0>; + spi-max-frequency = <400000>; + spi-cpha; + interrupt-parent = <&gpio1>; + interrupts = <16 1>; + ams,tuning-capacitor-pf = <80>; + ams,nflwdth = <0x44>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/proximity/as3935.txt b/Documentation/devicetree/bindings/iio/proximity/as3935.txt deleted file mode 100644 index 849115585d55..000000000000 --- a/Documentation/devicetree/bindings/iio/proximity/as3935.txt +++ /dev/null @@ -1,34 +0,0 @@ -Austrian Microsystems AS3935 Franklin lightning sensor device driver - -Required properties: - - compatible: must be "ams,as3935" - - reg: SPI chip select number for the device - - spi-max-frequency: specifies maximum SPI clock frequency - - spi-cpha: SPI Mode 1. Refer to spi/spi-bus.txt for generic SPI - slave node bindings. - - interrupts : the sole interrupt generated by the device - - Refer to interrupt-controller/interrupts.txt for generic - interrupt client node bindings. - -Optional properties: - - ams,tuning-capacitor-pf: Calibration tuning capacitor stepping - value 0 - 120pF. This will require using the calibration data from - the manufacturer. - - ams,nflwdth: Set the noise and watchdog threshold register on - startup. This will need to set according to the noise from the - MCU board, and possibly the local environment. Refer to the - datasheet for the threshold settings. - -Example: - -as3935@0 { - compatible = "ams,as3935"; - reg = <0>; - spi-max-frequency = <400000>; - spi-cpha; - interrupt-parent = <&gpio1>; - interrupts = <16 1>; - ams,tuning-capacitor-pf = <80>; - ams,nflwdth = <0x44>; -}; diff --git a/Documentation/devicetree/bindings/iio/proximity/semtech,sx9310.yaml b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9310.yaml index 5739074d3592..ccfb163f3d34 100644 --- a/Documentation/devicetree/bindings/iio/proximity/semtech,sx9310.yaml +++ b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9310.yaml @@ -40,6 +40,63 @@ properties: "#io-channel-cells": const: 1 + semtech,cs0-ground: + description: Indicates the CS0 sensor is connected to ground. + type: boolean + + semtech,combined-sensors: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: | + List of which sensors are combined and represented by CS3. + Possible values are - + 3 - CS3 (internal) + 0 1 - CS0 + CS1 + 1 2 - CS1 + CS2 (default) + 0 1 2 3 - CS0 + CS1 + CS2 + CS3 + items: + enum: [ 0, 1, 2, 3 ] + minItems: 1 + maxItems: 4 + + semtech,resolution: + description: + Capacitance measure resolution. Refer to datasheet for more details. + enum: + - coarsest + - very-coarse + - coarse + - medium-coarse + - medium + - fine + - very-fine + - finest + + semtech,startup-sensor: + $ref: /schemas/types.yaml#definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Sensor used for start-up proximity detection. The combined + sensor is represented by the value 3. This is used for initial + compensation. + + semtech,proxraw-strength: + $ref: /schemas/types.yaml#definitions/uint32 + enum: [0, 2, 4, 8] + default: 2 + description: + PROXRAW filter strength. A value of 0 represents off, and other values + represent 1-1/N. + + semtech,avg-pos-strength: + $ref: /schemas/types.yaml#definitions/uint32 + enum: [0, 16, 64, 128, 256, 512, 1024, 4294967295] + default: 16 + description: + Average positive filter strength. A value of 0 represents off and + UINT_MAX (4294967295) represents infinite. Other values + represent 1-1/N. + required: - compatible - reg @@ -61,5 +118,11 @@ examples: vdd-supply = <&pp3300_a>; svdd-supply = <&pp1800_prox>; #io-channel-cells = <1>; + semtech,cs0-ground; + semtech,combined-sensors = <1 2 3>; + semtech,resolution = "fine"; + semtech,startup-sensor = <1>; + semtech,proxraw-strength = <2>; + semtech,avg-pos-strength = <64>; }; }; diff --git a/Documentation/devicetree/bindings/iio/proximity/semtech,sx9500.yaml b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9500.yaml new file mode 100644 index 000000000000..66dd01506859 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9500.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/proximity/semtech,sx9500.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Semtech's SX9500 capacitive proximity button device + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +properties: + compatible: + const: semtech,sx9500 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + description: + GPIO connected to the active low reset pin. + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + proximity@28 { + compatible = "semtech,sx9500"; + reg = <0x28>; + interrupt-parent = <&gpio2>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/proximity/st,vl53l0x.yaml b/Documentation/devicetree/bindings/iio/proximity/st,vl53l0x.yaml new file mode 100644 index 000000000000..656460d9d8c8 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/st,vl53l0x.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/proximity/st,vl53l0x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ST VL53L0X ToF ranging sensor + +maintainers: + - Song Qiang <songqiang1304521@gmail.com> + +properties: + compatible: + const: st,vl53l0x + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + proximity@29 { + compatible = "st,vl53l0x"; + reg = <0x29>; + interrupt-parent = <&gpio>; + interrupts = <23 IRQ_TYPE_EDGE_FALLING>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/proximity/sx9500.txt b/Documentation/devicetree/bindings/iio/proximity/sx9500.txt deleted file mode 100644 index c54455db3bec..000000000000 --- a/Documentation/devicetree/bindings/iio/proximity/sx9500.txt +++ /dev/null @@ -1,23 +0,0 @@ -Semtech's SX9500 capacitive proximity button device driver - -Required properties: - - compatible: must be "semtech,sx9500" - - reg: i2c address where to find the device - - interrupts : the sole interrupt generated by the device - - Refer to interrupt-controller/interrupts.txt for generic - interrupt client node bindings. - -Optional properties: - - reset-gpios: Reference to the GPIO connected to the device's active - low reset pin. - -Example: - -sx9500@28 { - compatible = "semtech,sx9500"; - reg = <0x28>; - interrupt-parent = <&gpio2>; - interrupts = <16 IRQ_TYPE_LEVEL_LOW>; - reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; -}; diff --git a/Documentation/devicetree/bindings/iio/proximity/vl53l0x.txt b/Documentation/devicetree/bindings/iio/proximity/vl53l0x.txt deleted file mode 100644 index dfe00eb961cd..000000000000 --- a/Documentation/devicetree/bindings/iio/proximity/vl53l0x.txt +++ /dev/null @@ -1,18 +0,0 @@ -ST VL53L0X ToF ranging sensor - -Required properties: - - compatible: must be "st,vl53l0x" - - reg: i2c address where to find the device - -Optional properties: - - interrupts: Interrupt for notifying that new measurement is ready. - If no interrupt is specified, polling is used. - -Example: - -vl53l0x@29 { - compatible = "st,vl53l0x"; - reg = <0x29>; - interrupt-parent = <&gpio>; - interrupts = <23 IRQ_TYPE_EDGE_FALLING>; -}; diff --git a/Documentation/devicetree/bindings/iio/resolver/ad2s90.txt b/Documentation/devicetree/bindings/iio/resolver/ad2s90.txt deleted file mode 100644 index 477d41fa6467..000000000000 --- a/Documentation/devicetree/bindings/iio/resolver/ad2s90.txt +++ /dev/null @@ -1,31 +0,0 @@ -Analog Devices AD2S90 Resolver-to-Digital Converter - -https://www.analog.com/en/products/ad2s90.html - -Required properties: - - compatible: should be "adi,ad2s90" - - reg: SPI chip select number for the device - - spi-max-frequency: set maximum clock frequency, must be 830000 - - spi-cpol and spi-cpha: - Either SPI mode (0,0) or (1,1) must be used, so specify none or both of - spi-cpha, spi-cpol. - -See for more details: - Documentation/devicetree/bindings/spi/spi-bus.txt - -Note about max frequency: - Chip's max frequency, as specified in its datasheet, is 2Mhz. But a 600ns - delay is expected between the application of a logic LO to CS and the - application of SCLK, as also specified. And since the delay is not - implemented in the spi code, to satisfy it, SCLK's period should be at most - 2 * 600ns, so the max frequency should be 1 / (2 * 6e-7), which gives - roughly 830000Hz. - -Example: -resolver@0 { - compatible = "adi,ad2s90"; - reg = <0>; - spi-max-frequency = <830000>; - spi-cpol; - spi-cpha; -}; diff --git a/Documentation/devicetree/bindings/iio/resolver/adi,ad2s90.yaml b/Documentation/devicetree/bindings/iio/resolver/adi,ad2s90.yaml new file mode 100644 index 000000000000..81e4bdfc17c4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/resolver/adi,ad2s90.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/resolver/adi,ad2s90.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD2S90 Resolver-to-Digital Converter + +maintainers: + - Matheus Tavares <matheus.bernardino@usp.br> + +description: | + Datasheet: https://www.analog.com/en/products/ad2s90.html + +properties: + compatible: + const: adi,ad2s90 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 830000 + description: | + Chip's max frequency, as specified in its datasheet, is 2Mhz. But a 600ns + delay is expected between the application of a logic LO to CS and the + application of SCLK, as also specified. And since the delay is not + implemented in the spi code, to satisfy it, SCLK's period should be at + most 2 * 600ns, so the max frequency should be 1 / (2 * 6e-7), which gives + roughly 830000Hz. + + spi-cpol: true + + spi-cpha: true + +additionalProperties: false + +required: + - compatible + - reg + +dependencies: + spi-cpol: [ spi-cpha ] + spi-cpha: [ spi-cpol ] + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + resolver@0 { + compatible = "adi,ad2s90"; + reg = <0>; + spi-max-frequency = <830000>; + spi-cpol; + spi-cpha; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/samsung,sensorhub-rinato.yaml b/Documentation/devicetree/bindings/iio/samsung,sensorhub-rinato.yaml new file mode 100644 index 000000000000..a88b3b14d6bd --- /dev/null +++ b/Documentation/devicetree/bindings/iio/samsung,sensorhub-rinato.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/samsung,sensorhub-rinato.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Sensorhub driver + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: | + Sensorhub is a MCU which manages several sensors and also plays the role + of a virtual sensor device. + +properties: + compatible: + enum: + - samsung,sensorhub-rinato + - samsung,sensorhub-thermostat + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + ap-mcu-gpios: + maxItems: 1 + description: + Application Processor to sensorhub line - used during communication + + mcu-ap-gpios: + maxItems: 1 + description: + Sensorhub to Application Processor - used during communication + + mcu-reset-gpios: + maxItems: 1 + description: + Reset the sensorhub. + + spi-max-frequency: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - ap-mcu-gpios + - mcu-ap-gpios + - mcu-reset-gpios + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + sensorhub@0 { + compatible = "samsung,sensorhub-rinato"; + reg = <0>; + spi-max-frequency = <5000000>; + interrupt-parent = <&gpx0>; + interrupts = <2 0>; + ap-mcu-gpios = <&gpx0 0 0>; + mcu-ap-gpios = <&gpx0 4 0>; + mcu-reset-gpios = <&gpx0 5 0>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/sensorhub.txt b/Documentation/devicetree/bindings/iio/sensorhub.txt deleted file mode 100644 index b6ac0457d4ea..000000000000 --- a/Documentation/devicetree/bindings/iio/sensorhub.txt +++ /dev/null @@ -1,24 +0,0 @@ -Samsung Sensorhub driver - -Sensorhub is a MCU which manages several sensors and also plays the role -of a virtual sensor device. - -Required properties: -- compatible: "samsung,sensorhub-rinato" or "samsung,sensorhub-thermostat" -- spi-max-frequency: max SPI clock frequency -- interrupts: communication interrupt -- ap-mcu-gpios: [out] ap to sensorhub line - used during communication -- mcu-ap-gpios: [in] sensorhub to ap - used during communication -- mcu-reset-gpios: [out] sensorhub reset - -Example: - - shub_spi: shub { - compatible = "samsung,sensorhub-rinato"; - spi-max-frequency = <5000000>; - interrupt-parent = <&gpx0>; - interrupts = <2 0>; - ap-mcu-gpios = <&gpx0 0 0>; - mcu-ap-gpios = <&gpx0 4 0>; - mcu-reset-gpios = <&gpx0 5 0>; - }; diff --git a/Documentation/devicetree/bindings/iio/st,st-sensors.yaml b/Documentation/devicetree/bindings/iio/st,st-sensors.yaml new file mode 100644 index 000000000000..db291a9390b7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/st,st-sensors.yaml @@ -0,0 +1,123 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/st,st-sensors.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics MEMS sensors + +description: | + Note that whilst this covers many STMicro MEMs sensors, some more complex + IMUs need their own bindings. + The STMicroelectronics sensor devices are pretty straight-forward I2C or + SPI devices, all sharing the same device tree descriptions no matter what + type of sensor it is. + +maintainers: + - Denis Ciocca <denis.ciocca@st.com> + +properties: + compatible: + description: | + Some values are deprecated. + st,lis3lv02d (deprecated, use st,lis3lv02dl-accel) + st,lis302dl-spi (deprecated, use st,lis3lv02dl-accel) + enum: + # Accelerometers + - st,lis3lv02d + - st,lis302dl-spi + - st,lis3lv02dl-accel + - st,lsm303dlh-accel + - st,lsm303dlhc-accel + - st,lis3dh-accel + - st,lsm330d-accel + - st,lsm330dl-accel + - st,lsm330dlc-accel + - st,lis331dl-accel + - st,lis331dlh-accel + - st,lsm303dl-accel + - st,lsm303dlm-accel + - st,lsm330-accel + - st,lsm303agr-accel + - st,lis2dh12-accel + - st,h3lis331dl-accel + - st,lng2dm-accel + - st,lis3l02dq + - st,lis2dw12 + - st,lis3dhh + - st,lis3de + - st,lis2de12 + - st,lis2hh12 + # Gyroscopes + - st,l3g4200d-gyro + - st,lsm330d-gyro + - st,lsm330dl-gyro + - st,lsm330dlc-gyro + - st,l3gd20-gyro + - st,l3gd20h-gyro + - st,l3g4is-gyro + - st,lsm330-gyro + - st,lsm9ds0-gyro + # Magnetometers + - st,lsm303agr-magn + - st,lsm303dlh-magn + - st,lsm303dlhc-magn + - st,lsm303dlm-magn + - st,lis3mdl-magn + - st,lis2mdl + - st,lsm9ds1-magn + # Pressure sensors + - st,lps001wp-press + - st,lps25h-press + - st,lps331ap-press + - st,lps22hb-press + - st,lps33hw + - st,lps35hw + - st,lps22hh + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + + vdd-supply: true + vddio-supply: true + + st,drdy-int-pin: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Some sensors have multiple possible pins via which they can provide + a data ready interrupt. This selects which one. + enum: + - 1 + - 2 + + drive-open-drain: + $ref: /schemas/types.yaml#/definitions/flag + description: | + The interrupt/data ready line will be configured as open drain, which + is useful if several sensors share the same interrupt line. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + accelerometer@1d { + compatible = "st,lis3lv02dl-accel"; + reg = <0x1d>; + interrupt-parent = <&gpio2>; + interrupts = <18 IRQ_TYPE_EDGE_RISING>; + pinctrl-0 = <&lis3lv02dl_nhk_mode>; + pinctrl-names = "default"; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt deleted file mode 100644 index 3213599c5071..000000000000 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ /dev/null @@ -1,82 +0,0 @@ -STMicroelectronics MEMS sensors - -The STMicroelectronics sensor devices are pretty straight-forward I2C or -SPI devices, all sharing the same device tree descriptions no matter what -type of sensor it is. - -Required properties: -- compatible: see the list of valid compatible strings below -- reg: the I2C or SPI address the device will respond to - -Optional properties: -- vdd-supply: an optional regulator that needs to be on to provide VDD - power to the sensor. -- vddio-supply: an optional regulator that needs to be on to provide the - VDD IO power to the sensor. -- st,drdy-int-pin: the pin on the package that will be used to signal - "data ready" (valid values: 1 or 2). This property is not configurable - on all sensors. -- drive-open-drain: the interrupt/data ready line will be configured - as open drain, which is useful if several sensors share the same - interrupt line. (This binding is taken from pinctrl/pinctrl-bindings.txt) - This is a boolean property. - -Sensors may also have applicable pin control settings, those use the -standard bindings from pinctrl/pinctrl-bindings.txt. - -Valid compatible strings: - -Accelerometers: -- st,lis3lv02d (deprecated, use st,lis3lv02dl-accel) -- st,lis302dl-spi (deprecated, use st,lis3lv02dl-accel) -- st,lis3lv02dl-accel -- st,lsm303dlh-accel -- st,lsm303dlhc-accel -- st,lis3dh-accel -- st,lsm330d-accel -- st,lsm330dl-accel -- st,lsm330dlc-accel -- st,lis331dl-accel -- st,lis331dlh-accel -- st,lsm303dl-accel -- st,lsm303dlm-accel -- st,lsm330-accel -- st,lsm303agr-accel -- st,lis2dh12-accel -- st,h3lis331dl-accel -- st,lng2dm-accel -- st,lis3l02dq -- st,lis2dw12 -- st,lis3dhh -- st,lis3de -- st,lis2de12 -- st,lis2hh12 - -Gyroscopes: -- st,l3g4200d-gyro -- st,lsm330d-gyro -- st,lsm330dl-gyro -- st,lsm330dlc-gyro -- st,l3gd20-gyro -- st,l3gd20h-gyro -- st,l3g4is-gyro -- st,lsm330-gyro -- st,lsm9ds0-gyro - -Magnetometers: -- st,lsm303agr-magn -- st,lsm303dlh-magn -- st,lsm303dlhc-magn -- st,lsm303dlm-magn -- st,lis3mdl-magn -- st,lis2mdl -- st,lsm9ds1-magn - -Pressure sensors: -- st,lps001wp-press -- st,lps25h-press -- st,lps331ap-press -- st,lps22hb-press -- st,lps33hw -- st,lps35hw -- st,lps22hh diff --git a/Documentation/devicetree/bindings/iio/temperature/max31856.txt b/Documentation/devicetree/bindings/iio/temperature/max31856.txt deleted file mode 100644 index 06ab43bb4de8..000000000000 --- a/Documentation/devicetree/bindings/iio/temperature/max31856.txt +++ /dev/null @@ -1,24 +0,0 @@ -Maxim MAX31856 thermocouple support - -https://datasheets.maximintegrated.com/en/ds/MAX31856.pdf - -Optional property: - - thermocouple-type: Type of thermocouple (THERMOCOUPLE_TYPE_K if - omitted). Supported types are B, E, J, K, N, R, S, T. - -Required properties: - - compatible: must be "maxim,max31856" - - reg: SPI chip select number for the device - - spi-max-frequency: As per datasheet max. supported freq is 5000000 - - spi-cpha: must be defined for max31856 to enable SPI mode 1 - - Refer to spi/spi-bus.txt for generic SPI slave bindings. - - Example: - temp-sensor@0 { - compatible = "maxim,max31856"; - reg = <0>; - spi-max-frequency = <5000000>; - spi-cpha; - thermocouple-type = <THERMOCOUPLE_TYPE_K>; - }; diff --git a/Documentation/devicetree/bindings/iio/temperature/maxim,max31855k.yaml b/Documentation/devicetree/bindings/iio/temperature/maxim,max31855k.yaml new file mode 100644 index 000000000000..9969bac66aa1 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/maxim,max31855k.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/temperature/maxim,max31855k.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX31855 and similar thermocouples + +maintainers: + - Matt Ranostay <matt.ranostay@konsulko.com> + +description: | + https://datasheets.maximintegrated.com/en/ds/MAX6675.pdf + https://datasheets.maximintegrated.com/en/ds/MAX31855.pdf + +properties: + compatible: + description: + The generic maxim,max31855 compatible is deprecated in favour of + the thermocouple type specific variants. + enum: + - maxim,max6675 + - maxim,max31855 + - maxim,max31855k + - maxim,max31855j + - maxim,max31855n + - maxim,max31855s + - maxim,max31855t + - maxim,max31855e + - maxim,max31855r + + reg: + maxItems: 1 + + spi-max-frequency: true + spi-cpha: true + +required: + - compatible + - reg + +allOf: + - if: + properties: + compatible: + contains: + enum: + - maxim,max6675 + then: + required: + - spi-cpha + else: + properties: + spi-cpha: false + +additionalProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + temp-sensor@0 { + compatible = "maxim,max31855k"; + reg = <0>; + spi-max-frequency = <4300000>; + }; + temp-sensor@1 { + compatible = "maxim,max6675"; + reg = <1>; + spi-max-frequency = <4300000>; + spi-cpha; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/temperature/maxim,max31856.yaml b/Documentation/devicetree/bindings/iio/temperature/maxim,max31856.yaml new file mode 100644 index 000000000000..873b34766676 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/maxim,max31856.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/temperature/maxim,max31856.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX31856 thermocouple support + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: | + https://datasheets.maximintegrated.com/en/ds/MAX31856.pdf + +properties: + compatible: + const: maxim,max31856 + + reg: + maxItems: 1 + + spi-max-frequency: true + spi-cpha: true + + thermocouple-type: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Type of thermocouple (THERMOCOUPLE_TYPE_K if omitted). + Use defines in dt-bindings/iio/temperature/thermocouple.h. + Supported types are B, E, J, K, N, R, S, T. + +required: + - compatible + - reg + - spi-cpha + +additionalProperties: false + +examples: + - | + #include <dt-bindings/iio/temperature/thermocouple.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + temp-sensor@0 { + compatible = "maxim,max31856"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + thermocouple-type = <THERMOCOUPLE_TYPE_K>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt deleted file mode 100644 index bb85cd0e039c..000000000000 --- a/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt +++ /dev/null @@ -1,24 +0,0 @@ -Maxim thermocouple support - -* https://datasheets.maximintegrated.com/en/ds/MAX6675.pdf -* https://datasheets.maximintegrated.com/en/ds/MAX31855.pdf - -Required properties: - - - compatible: must be "maxim,max6675" or one of the following: - "maxim,max31855k", "maxim,max31855j", "maxim,max31855n", - "maxim,max31855s", "maxim,max31855t", "maxim,max31855e", - "maxim,max31855r"; the generic "max,max31855" is deprecated. - - reg: SPI chip select number for the device - - spi-max-frequency: must be 4300000 - - spi-cpha: must be defined for max6675 to enable SPI mode 1 - - Refer to spi/spi-bus.txt for generic SPI slave bindings. - -Example: - - max31855@0 { - compatible = "maxim,max31855k"; - reg = <0>; - spi-max-frequency = <4300000>; - }; diff --git a/Documentation/devicetree/bindings/iio/temperature/melexis,mlx90614.yaml b/Documentation/devicetree/bindings/iio/temperature/melexis,mlx90614.yaml new file mode 100644 index 000000000000..d6965a0c1cf3 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/melexis,mlx90614.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/temperature/melexis,mlx90614.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Melexis MLX90614 contactless IR temperature sensor + +maintainers: + - Peter Meerwald <pmeerw@pmeerw.net> + - Crt Mori <cmo@melexis.com> + +description: | + http://melexis.com/Infrared-Thermometer-Sensors/Infrared-Thermometer-Sensors/MLX90614-615.aspx + +properties: + compatible: + const: melexis,mlx90614 + + reg: + maxItems: 1 + + wakeup-gpios: + description: + GPIO connected to the SDA line to hold low in order to wake up the + device. In normal operation, the GPIO is set as input and will + not interfere in I2C communication. There is no need for a GPIO + driving the SCL line. If no GPIO is given, power management is disabled. + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + temp-sensor@5a { + compatible = "melexis,mlx90614"; + reg = <0x5a>; + wakeup-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/temperature/melexis,mlx90632.yaml b/Documentation/devicetree/bindings/iio/temperature/melexis,mlx90632.yaml new file mode 100644 index 000000000000..b547ddcd544a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/melexis,mlx90632.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/temperature/melexis,mlx90632.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Melexis MLX90632 contactless Infra Red temperature sensor + +maintainers: + - Crt Mori <cmo@melexis.com> + +description: | + https://www.melexis.com/en/documents/documentation/datasheets/datasheet-mlx90632 + + There are various applications for the Infra Red contactless temperature + sensor and MLX90632 is most suitable for consumer applications where + measured object temperature is in range between -20 to 200 degrees + Celsius with relative error of measurement below 1 degree Celsius in + object temperature range for industrial applications. Since it can + operate and measure ambient temperature in range of -20 to 85 degrees + Celsius it is suitable also for outdoor use. + + Be aware that electronics surrounding the sensor can increase ambient + temperature. MLX90632 can be calibrated to reduce the housing effect via + already existing EEPROM parameters. + + Since measured object emissivity effects Infra Red energy emitted, + emissivity should be set before requesting the object temperature. + +properties: + compatible: + const: melexis,mlx90632 + + reg: + maxItems: 1 + description: Default is 0x3a, but can be reprogrammed. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + temp-sensor@3a { + compatible = "melexis,mlx90632"; + reg = <0x3a>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt b/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt deleted file mode 100644 index 9be57b036092..000000000000 --- a/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt +++ /dev/null @@ -1,24 +0,0 @@ -* Melexis MLX90614 contactless IR temperature sensor - -http://melexis.com/Infrared-Thermometer-Sensors/Infrared-Thermometer-Sensors/MLX90614-615.aspx - -Required properties: - - - compatible: should be "melexis,mlx90614" - - reg: the I2C address of the sensor - -Optional properties: - - - wakeup-gpios: device tree identifier of the GPIO connected to the SDA line - to hold low in order to wake up the device. In normal operation, the - GPIO is set as input and will not interfere in I2C communication. There - is no need for a GPIO driving the SCL line. If no GPIO is given, power - management is disabled. - -Example: - -mlx90614@5a { - compatible = "melexis,mlx90614"; - reg = <0x5a>; - wakeup-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; -}; diff --git a/Documentation/devicetree/bindings/iio/temperature/mlx90632.txt b/Documentation/devicetree/bindings/iio/temperature/mlx90632.txt deleted file mode 100644 index 0b05812001f8..000000000000 --- a/Documentation/devicetree/bindings/iio/temperature/mlx90632.txt +++ /dev/null @@ -1,28 +0,0 @@ -* Melexis MLX90632 contactless Infra Red temperature sensor - -Link to datasheet: https://www.melexis.com/en/documents/documentation/datasheets/datasheet-mlx90632 - -There are various applications for the Infra Red contactless temperature sensor -and MLX90632 is most suitable for consumer applications where measured object -temperature is in range between -20 to 200 degrees Celsius with relative error -of measurement below 1 degree Celsius in object temperature range for -industrial applications. Since it can operate and measure ambient temperature -in range of -20 to 85 degrees Celsius it is suitable also for outdoor use. - -Be aware that electronics surrounding the sensor can increase ambient -temperature. MLX90632 can be calibrated to reduce the housing effect via -already existing EEPROM parameters. - -Since measured object emissivity effects Infra Red energy emitted, emissivity -should be set before requesting the object temperature. - -Required properties: - - compatible: should be "melexis,mlx90632" - - reg: the I2C address of the sensor (default 0x3a) - -Example: - -mlx90632@3a { - compatible = "melexis,mlx90632"; - reg = <0x3a>; -}; diff --git a/Documentation/devicetree/bindings/iio/temperature/temperature-bindings.txt b/Documentation/devicetree/bindings/iio/temperature/temperature-bindings.txt deleted file mode 100644 index 8f339cab74ae..000000000000 --- a/Documentation/devicetree/bindings/iio/temperature/temperature-bindings.txt +++ /dev/null @@ -1,7 +0,0 @@ -If the temperature sensor device can be configured to use some specific -thermocouple type, you can use the defined types provided in the file -"include/dt-bindings/iio/temperature/thermocouple.h". - -Property: -thermocouple-type: A single cell representing the type of the thermocouple - used by the device. diff --git a/Documentation/devicetree/bindings/iio/temperature/ti,tmp007.yaml b/Documentation/devicetree/bindings/iio/temperature/ti,tmp007.yaml new file mode 100644 index 000000000000..3c2b7189fa2e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/ti,tmp007.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/temperature/ti,tmp007.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: IR thermopile sensor with integrated math engine + +maintainers: + - Manivannan Sadhasivam <manivannanece23@gmail.com> + +description: | + http://www.ti.com/lit/ds/symlink/tmp007.pdf + +properties: + compatible: + const: ti,tmp007 + + reg: + description: | + The I2C address of the sensor (changeable via ADR pins) + ------------------------------ + |ADR1 | ADR0 | Device Address| + ------------------------------ + 0 0 0x40 + 0 1 0x41 + 0 SDA 0x42 + 0 SCL 0x43 + 1 0 0x44 + 1 1 0x45 + 1 SDA 0x46 + 1 SCL 0x47 + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + temp-sensor@40 { + compatible = "ti,tmp007"; + reg = <0x40>; + interrupt-parent = <&gpio0>; + interrupts = <5 0x08>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/temperature/tmp007.txt b/Documentation/devicetree/bindings/iio/temperature/tmp007.txt deleted file mode 100644 index da0af234a357..000000000000 --- a/Documentation/devicetree/bindings/iio/temperature/tmp007.txt +++ /dev/null @@ -1,33 +0,0 @@ -* TI TMP007 - IR thermopile sensor with integrated math engine - -Link to datasheet: http://www.ti.com/lit/ds/symlink/tmp007.pdf - -Required properties: - - - compatible: should be "ti,tmp007" - - reg: the I2C address of the sensor (changeable via ADR pins) - ------------------------------ - |ADR1 | ADR0 | Device Address| - ------------------------------ - 0 0 0x40 - 0 1 0x41 - 0 SDA 0x42 - 0 SCL 0x43 - 1 0 0x44 - 1 1 0x45 - 1 SDA 0x46 - 1 SCL 0x47 - -Optional properties: - - - interrupts: interrupt mapping for GPIO IRQ (level active low) - -Example: - -tmp007@40 { - compatible = "ti,tmp007"; - reg = <0x40>; - interrupt-parent = <&gpio0>; - interrupts = <5 0x08>; -}; - diff --git a/Documentation/devicetree/bindings/iio/temperature/tsys01.txt b/Documentation/devicetree/bindings/iio/temperature/tsys01.txt deleted file mode 100644 index 0d5cc5595d0c..000000000000 --- a/Documentation/devicetree/bindings/iio/temperature/tsys01.txt +++ /dev/null @@ -1,19 +0,0 @@ -* TSYS01 - Measurement Specialties temperature sensor - -Required properties: - - - compatible: should be "meas,tsys01" - - reg: I2C address of the sensor (changeable via CSB pin) - - ------------------------ - | CSB | Device Address | - ------------------------ - 1 0x76 - 0 0x77 - -Example: - -tsys01@76 { - compatible = "meas,tsys01"; - reg = <0x76>; -}; diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinmux.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinmux.yaml new file mode 100644 index 000000000000..7dea3e26d99e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinmux.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/ralink,rt2880-pinmux.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ralink rt2880 pinmux controller + +maintainers: + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +description: + The rt2880 pinmux can only set the muxing of pin groups. muxing indiviual pins + is not supported. There is no pinconf support. + +properties: + compatible: + enum: + - ralink,rt2880-pinmux + + pinctrl-0: + description: + A phandle to the node containing the subnodes containing default + configurations. This is for pinctrl hogs. + + pinctrl-names: + description: + A pinctrl state named "default" can be defined. + const: default + +required: + - compatible + +patternProperties: + '[a-z0-9_-]+': + if: + type: object + description: node for pinctrl. + $ref: "pinmux-node.yaml" + then: + properties: + groups: + description: Name of the pin group to use for the functions. + enum: [i2c, spi, uart1, uart2, uart3, rgmii1, rgmii2, mdio, + pcie, sdhci] + function: + description: The mux function to select + enum: [gpio, i2c, spi, uart1, uart2, uart3, rgmii1, rgmii2, + mdio, nand1, nand2, sdhci] + +additionalProperties: false + +examples: + # Pinmux controller node + - | + pinctrl { + compatible = "ralink,rt2880-pinmux"; + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinctrl0 { + }; + + i2c_pins: i2c0 { + i2c0 { + groups = "i2c"; + function = "i2c"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml index ab623ba930d5..52a7f793737e 100644 --- a/Documentation/devicetree/bindings/trivial-devices.yaml +++ b/Documentation/devicetree/bindings/trivial-devices.yaml @@ -44,6 +44,8 @@ properties: - atmel,atsha204a # i2c h/w elliptic curve crypto module - atmel,atecc508a + # Bosch Sensortec pressure, temperature, humididty and VOC sensor + - bosch,bme680 # CM32181: Ambient Light Sensor - capella,cm32181 # CM3232: Ambient Light Sensor @@ -70,6 +72,12 @@ properties: - dlg,da9053 # DA9063: system PMIC for quad-core application processors - dlg,da9063 + # DMARD05: 3-axis I2C Accelerometer + - domintech,dmard05 + # DMARD06: 3-axis I2C Accelerometer + - domintech,dmard06 + # DMARD05: 3-axis I2C Accelerometer + - domintech,dmard07 # DMARD09: 3-axis Accelerometer - domintech,dmard09 # DMARD10: 3-axis Accelerometer @@ -108,20 +116,22 @@ properties: - isil,isl68137 # 5 Bit Programmable, Pulse-Width Modulator - maxim,ds1050 - # 10-bit 8 channels 300ks/s SPI ADC with temperature sensor - - maxim,max1027 - # 10-bit 12 channels 300ks/s SPI ADC with temperature sensor - - maxim,max1029 - # 10-bit 16 channels 300ks/s SPI ADC with temperature sensor - - maxim,max1031 - # 12-bit 8 channels 300ks/s SPI ADC with temperature sensor - - maxim,max1227 - # 12-bit 12 channels 300ks/s SPI ADC with temperature sensor - - maxim,max1229 - # 12-bit 16 channels 300ks/s SPI ADC with temperature sensor - - maxim,max1231 + # 10 kOhm digital potentiometer with I2C interface + - maxim,ds1803-010 + # 50 kOhm digital potentiometer with I2C interface + - maxim,ds1803-050 + # 100 kOhm digital potentiometer with I2C interface + - maxim,ds1803-100 # Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs - maxim,max1237 + # 10-bit 10 kOhm linear programable voltage divider + - maxim,max5481 + # 10-bit 50 kOhm linear programable voltage divider + - maxim,max5482 + # 10-bit 10 kOhm linear programable variable resistor + - maxim,max5483 + # 10-bit 50 kOhm linear programable variable resistor + - maxim,max5484 # PECI-to-I2C translator for PECI-to-SMBus/I2C protocol conversion - maxim,max6621 # 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface @@ -130,8 +140,24 @@ properties: - maxim,max31730 # mCube 3-axis 8-bit digital accelerometer - mcube,mc3230 + # MEMSIC magnetometer + - memsic,mmc35240 # MEMSIC 2-axis 8-bit digital accelerometer - memsic,mxc6225 + # Measurement Specialities I2C temperature and humidity sensor + - meas,htu21 + # Measurement Specialities I2C pressure and temperature sensor + - meas,ms5637 + # Measurement Specialities I2C pressure and temperature sensor + - meas,ms5805 + # Measurement Specialities I2C pressure and temperature sensor + - meas,ms5837 + # Measurement Specialities temp and humidity part of ms8607 device + - meas,ms8607-humidity + # Measurement Specialities temp and pressure part of ms8607 device + - meas,ms8607-temppressure + # Measurement Specialties temperature sensor + - meas,tsys01 # Microchip differential I2C ADC, 1 Channel, 18 bit - microchip,mcp3421 # Microchip differential I2C ADC, 2 Channel, 18 bit @@ -172,134 +198,6 @@ properties: - microchip,mcp4019-503 # Microchip 7-bit Single I2C Digital POT (100k) - microchip,mcp4019-104 - # Microchip 7-bit Single I2C Digital Potentiometer (5k) - - microchip,mcp4531-502 - # Microchip 7-bit Single I2C Digital Potentiometer (10k) - - microchip,mcp4531-103 - # Microchip 7-bit Single I2C Digital Potentiometer (50k) - - microchip,mcp4531-503 - # Microchip 7-bit Single I2C Digital Potentiometer (100k) - - microchip,mcp4531-104 - # Microchip 7-bit Single I2C Digital Potentiometer (5k) - - microchip,mcp4532-502 - # Microchip 7-bit Single I2C Digital Potentiometer (10k) - - microchip,mcp4532-103 - # Microchip 7-bit Single I2C Digital Potentiometer (50k) - - microchip,mcp4532-503 - # Microchip 7-bit Single I2C Digital Potentiometer (100k) - - microchip,mcp4532-104 - # Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (5k) - - microchip,mcp4541-502 - # Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (10k) - - microchip,mcp4541-103 - # Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (50k) - - microchip,mcp4541-503 - # Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (100k) - - microchip,mcp4541-104 - # Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (5k) - - microchip,mcp4542-502 - # Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (10k) - - microchip,mcp4542-103 - # Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (50k) - - microchip,mcp4542-503 - # Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (100k) - - microchip,mcp4542-104 - # Microchip 8-bit Single I2C Digital Potentiometer (5k) - - microchip,mcp4551-502 - # Microchip 8-bit Single I2C Digital Potentiometer (10k) - - microchip,mcp4551-103 - # Microchip 8-bit Single I2C Digital Potentiometer (50k) - - microchip,mcp4551-503 - # Microchip 8-bit Single I2C Digital Potentiometer (100k) - - microchip,mcp4551-104 - # Microchip 8-bit Single I2C Digital Potentiometer (5k) - - microchip,mcp4552-502 - # Microchip 8-bit Single I2C Digital Potentiometer (10k) - - microchip,mcp4552-103 - # Microchip 8-bit Single I2C Digital Potentiometer (50k) - - microchip,mcp4552-503 - # Microchip 8-bit Single I2C Digital Potentiometer (100k) - - microchip,mcp4552-104 - # Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (5k) - - microchip,mcp4561-502 - # Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (10k) - - microchip,mcp4561-103 - # Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (50k) - - microchip,mcp4561-503 - # Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (100k) - - microchip,mcp4561-104 - # Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (5k) - - microchip,mcp4562-502 - # Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (10k) - - microchip,mcp4562-103 - # Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (50k) - - microchip,mcp4562-503 - # Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (100k) - - microchip,mcp4562-104 - # Microchip 7-bit Dual I2C Digital Potentiometer (5k) - - microchip,mcp4631-502 - # Microchip 7-bit Dual I2C Digital Potentiometer (10k) - - microchip,mcp4631-103 - # Microchip 7-bit Dual I2C Digital Potentiometer (50k) - - microchip,mcp4631-503 - # Microchip 7-bit Dual I2C Digital Potentiometer (100k) - - microchip,mcp4631-104 - # Microchip 7-bit Dual I2C Digital Potentiometer (5k) - - microchip,mcp4632-502 - # Microchip 7-bit Dual I2C Digital Potentiometer (10k) - - microchip,mcp4632-103 - # Microchip 7-bit Dual I2C Digital Potentiometer (50k) - - microchip,mcp4632-503 - # Microchip 7-bit Dual I2C Digital Potentiometer (100k) - - microchip,mcp4632-104 - # Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (5k) - - microchip,mcp4641-502 - # Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (10k) - - microchip,mcp4641-103 - # Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (50k) - - microchip,mcp4641-503 - # Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (100k) - - microchip,mcp4641-104 - # Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (5k) - - microchip,mcp4642-502 - # Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (10k) - - microchip,mcp4642-103 - # Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (50k) - - microchip,mcp4642-503 - # Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (100k) - - microchip,mcp4642-104 - # Microchip 8-bit Dual I2C Digital Potentiometer (5k) - - microchip,mcp4651-502 - # Microchip 8-bit Dual I2C Digital Potentiometer (10k) - - microchip,mcp4651-103 - # Microchip 8-bit Dual I2C Digital Potentiometer (50k) - - microchip,mcp4651-503 - # Microchip 8-bit Dual I2C Digital Potentiometer (100k) - - microchip,mcp4651-104 - # Microchip 8-bit Dual I2C Digital Potentiometer (5k) - - microchip,mcp4652-502 - # Microchip 8-bit Dual I2C Digital Potentiometer (10k) - - microchip,mcp4652-103 - # Microchip 8-bit Dual I2C Digital Potentiometer (50k) - - microchip,mcp4652-503 - # Microchip 8-bit Dual I2C Digital Potentiometer (100k) - - microchip,mcp4652-104 - # Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (5k) - - microchip,mcp4661-502 - # Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (10k) - - microchip,mcp4661-103 - # Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (50k) - - microchip,mcp4661-503 - # Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k) - - microchip,mcp4661-104 - # Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (5k) - - microchip,mcp4662-502 - # Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (10k) - - microchip,mcp4662-103 - # Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (50k) - - microchip,mcp4662-503 - # Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k) - - microchip,mcp4662-104 # PWM Fan Speed Controller With Fan Fault Detection - microchip,tc654 # PWM Fan Speed Controller With Fan Fault Detection @@ -336,8 +234,14 @@ properties: - plx,pex8648 # Pulsedlight LIDAR range-finding sensor - pulsedlight,lidar-lite-v2 + # Renesas ISL29501 time-of-flight sensor + - renesas,isl29501 # S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) - samsung,24ad0xd1 + # Sensirion low power multi-pixel gas sensor with I2C interface + - sensirion,sgpc3 + # Sensirion multi-pixel gas sensor with I2C interface + - sensirion,sgp30 # SGX Sensortech VZ89X Sensors - sgx,vz89x # Relative Humidity and Temperature Sensors @@ -356,6 +260,16 @@ properties: - ti,ads7830 # Temperature Monitoring and Fan Control - ti,amc6821 + # Temperature and humidity sensor with i2c interface + - ti,hdc1000 + # Temperature and humidity sensor with i2c interface + - ti,hdc1008 + # Temperature and humidity sensor with i2c interface + - ti,hdc1010 + # Temperature and humidity sensor with i2c interface + - ti,hdc1050 + # Temperature and humidity sensor with i2c interface + - ti,hdc1080 # Temperature sensor with 2-wire interface - ti,lm73 # Temperature sensor with integrated fan control |