diff options
Diffstat (limited to 'Documentation')
4 files changed, 137 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index c96d8dcf98fd..4ab09f2202d4 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -3,28 +3,43 @@ SATA nodes are defined to describe on-chip Serial ATA controllers. Each SATA controller should have its own node. +It is possible, but not required, to represent each port as a sub-node. +It allows to enable each port independently when dealing with multiple +PHYs. + Required properties: - compatible : compatible string, one of: - "allwinner,sun4i-a10-ahci" - - "fsl,imx53-ahci" - - "fsl,imx6q-ahci" - "hisilicon,hisi-ahci" - "ibm,476gtr-ahci" - "marvell,armada-380-ahci" - "snps,dwc-ahci" - "snps,exynos5440-ahci" - "snps,spear-ahci" + - "generic-ahci" - interrupts : <interrupt mapping for SATA IRQ> - reg : <registers mapping> +Please note that when using "generic-ahci" you must also specify a SoC specific +compatible: + compatible = "manufacturer,soc-model-ahci", "generic-ahci"; + Optional properties: - dma-coherent : Present if dma operations are coherent - clocks : a list of phandle + clock specifier pairs - target-supply : regulator for SATA target power +- phys : reference to the SATA PHY node +- phy-names : must be "sata-phy" + +Required properties when using sub-nodes: +- #address-cells : number of cells to encode an address +- #size-cells : number of cells representing the size of an address + + +Sub-nodes required properties: +- reg : the port number +- phys : reference to the SATA PHY node -"fsl,imx53-ahci", "fsl,imx6q-ahci" required properties: -- clocks : must contain the sata, sata_ref and ahb clocks -- clock-names : must contain "ahb" for the ahb clock Examples: sata@ffe08000 { @@ -40,3 +55,23 @@ Examples: clocks = <&pll6 0>, <&ahb_gates 25>; target-supply = <®_ahci_5v>; }; + +With sub-nodes: + sata@f7e90000 { + compatible = "marvell,berlin2q-achi", "generic-ahci"; + reg = <0xe90000 0x1000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&chip CLKID_SATA>; + #address-cells = <1>; + #size-cells = <0>; + + sata0: sata-port@0 { + reg = <0>; + phys = <&sata_phy 0>; + }; + + sata1: sata-port@1 { + reg = <1>; + phys = <&sata_phy 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/ata/ahci-st.txt b/Documentation/devicetree/bindings/ata/ahci-st.txt new file mode 100644 index 000000000000..0574a77a0b9f --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-st.txt @@ -0,0 +1,31 @@ +STMicroelectronics STi SATA controller + +This binding describes a SATA device. + +Required properties: + - compatible : Must be "st,sti-ahci" + - reg : Physical base addresses and length of register sets + - interrupts : Interrupt associated with the SATA device + - interrupt-names : Associated name must be; "hostc" + - resets : The power-down and soft-reset lines of SATA IP + - reset-names : Associated names must be; "pwr-dwn" and "sw-rst" + - clocks : The phandle for the clock + - clock-names : Associated name must be; "ahci_clk" + - phys : The phandle for the PHY device + - phy-names : Associated name must be; "ahci_phy" + +Example: + + sata0: sata@fe380000 { + compatible = "st,sti-ahci"; + reg = <0xfe380000 0x1000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; + interrupt-names = "hostc"; + phys = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>; + phy-names = "ahci_phy"; + resets = <&powerdown STIH416_SATA0_POWERDOWN>, + <&softreset STIH416_SATA0_SOFTRESET>; + reset-names = "pwr-dwn", "sw-rst"; + clocks = <&clk_s_a0_ls CLK_ICN_REG>; + clock-names = "ahci_clk"; + }; diff --git a/Documentation/devicetree/bindings/ata/imx-sata.txt b/Documentation/devicetree/bindings/ata/imx-sata.txt new file mode 100644 index 000000000000..fa511db18408 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/imx-sata.txt @@ -0,0 +1,36 @@ +* Freescale i.MX AHCI SATA Controller + +The Freescale i.MX SATA controller mostly conforms to the AHCI interface +with some special extensions at integration level. + +Required properties: +- compatible : should be one of the following: + - "fsl,imx53-ahci" for i.MX53 SATA controller + - "fsl,imx6q-ahci" for i.MX6Q SATA controller +- interrupts : interrupt mapping for SATA IRQ +- reg : registers mapping +- clocks : list of clock specifiers, must contain an entry for each + required entry in clock-names +- clock-names : should include "sata", "sata_ref" and "ahb" entries + +Optional properties: +- fsl,transmit-level-mV : transmit voltage level, in millivolts. +- fsl,transmit-boost-mdB : transmit boost level, in milli-decibels +- fsl,transmit-atten-16ths : transmit attenuation, in 16ths +- fsl,receive-eq-mdB : receive equalisation, in milli-decibels + Please refer to the technical documentation or the driver source code + for the list of legal values for these options. +- fsl,no-spread-spectrum : disable spread-spectrum clocking on the SATA + link. + +Examples: + +sata@02200000 { + compatible = "fsl,imx6q-ahci"; + reg = <0x02200000 0x4000>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_SATA>, + <&clks IMX6QDL_CLK_SATA_REF_100M>, + <&clks IMX6QDL_CLK_AHB>; + clock-names = "sata", "sata_ref", "ahb"; +}; diff --git a/Documentation/devicetree/bindings/ata/tegra-sata.txt b/Documentation/devicetree/bindings/ata/tegra-sata.txt new file mode 100644 index 000000000000..946f2072570b --- /dev/null +++ b/Documentation/devicetree/bindings/ata/tegra-sata.txt @@ -0,0 +1,30 @@ +Tegra124 SoC SATA AHCI controller + +Required properties : +- compatible : "nvidia,tegra124-ahci". +- reg : Should contain 2 entries: + - AHCI register set (SATA BAR5) + - SATA register set +- interrupts : Defines the interrupt used by SATA +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - sata + - sata-oob + - cml1 + - pll_e +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - sata + - sata-oob + - sata-cold +- phys : Must contain an entry for each entry in phy-names. + See ../phy/phy-bindings.txt for details. +- phy-names : Must include the following entries: + - sata-phy : XUSB PADCTL SATA PHY +- hvdd-supply : Defines the SATA HVDD regulator +- vddio-supply : Defines the SATA VDDIO regulator +- avdd-supply : Defines the SATA AVDD regulator +- target-5v-supply : Defines the SATA 5V power regulator +- target-12v-supply : Defines the SATA 12V power regulator |