summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/usb/dwc3.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/usb/dwc3.txt')
-rw-r--r--Documentation/devicetree/bindings/usb/dwc3.txt128
1 files changed, 0 insertions, 128 deletions
diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
deleted file mode 100644
index 1aae2b6160c1..000000000000
--- a/Documentation/devicetree/bindings/usb/dwc3.txt
+++ /dev/null
@@ -1,128 +0,0 @@
-synopsys DWC3 CORE
-
-DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
- as described in 'usb/generic.txt'
-
-Required properties:
- - compatible: must be "snps,dwc3"
- - reg : Address and length of the register set for the device
- - interrupts: Interrupts used by the dwc3 controller.
- - clock-names: list of clock names. Ideally should be "ref",
- "bus_early", "suspend" but may be less or more.
- - clocks: list of phandle and clock specifier pairs corresponding to
- entries in the clock-names property.
-
-Exception for clocks:
- clocks are optional if the parent node (i.e. glue-layer) is compatible to
- one of the following:
- "cavium,octeon-7130-usb-uctl"
- "qcom,dwc3"
- "samsung,exynos5250-dwusb3"
- "samsung,exynos5433-dwusb3"
- "samsung,exynos7-dwusb3"
- "sprd,sc9860-dwc3"
- "st,stih407-dwc3"
- "ti,am437x-dwc3"
- "ti,dwc3"
- "ti,keystone-dwc3"
- "rockchip,rk3399-dwc3"
- "xlnx,zynqmp-dwc3"
-
-Optional properties:
- - usb-phy : array of phandle for the PHY device. The first element
- in the array is expected to be a handle to the USB2/HS PHY and
- the second element is expected to be a handle to the USB3/SS PHY
- - phys: from the *Generic PHY* bindings
- - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy"
- or "usb3-phy".
- - resets: set of phandle and reset specifier pairs
- - snps,usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM
- - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
- - snps,dis-start-transfer-quirk: when set, disable isoc START TRANSFER command
- failure SW work-around for DWC_usb31 version 1.70a-ea06
- and prior.
- - snps,disable_scramble_quirk: true when SW should disable data scrambling.
- Only really useful for FPGA builds.
- - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled
- - snps,lpm-nyet-threshold: LPM NYET threshold
- - snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk
- - snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
- - snps,req_p1p2p3_quirk: when set, the core will always request for
- P1/P2/P3 transition sequence.
- - snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain
- amount of 8B10B errors occur.
- - snps,del_phy_power_chg_quirk: when set core will delay PHY power change
- from P0 to P1/P2/P3.
- - snps,lfps_filter_quirk: when set core will filter LFPS reception.
- - snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start
- Polling LFPS after RX.Detect.
- - snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value.
- - snps,tx_de_emphasis: the value driven to the PHY is controlled by the
- LTSSM during USB3 Compliance mode.
- - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
- - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
- - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
- disabling the suspend signal to the PHY.
- - snps,dis-u1-entry-quirk: set if link entering into U1 needs to be disabled.
- - snps,dis-u2-entry-quirk: set if link entering into U2 needs to be disabled.
- - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection
- in PHY P3 power state.
- - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists
- in GUSB2PHYCFG, specify that USB2 PHY doesn't provide
- a free-running PHY clock.
- - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power
- from P0 to P1/P2/P3 without delay.
- - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check
- during HS transmit.
- - snps,parkmode-disable-ss-quirk: when set, all SuperSpeed bus instances in
- park mode are disabled.
- - snps,dis_metastability_quirk: when set, disable metastability workaround.
- CAUTION: use only if you are absolutely sure of it.
- - snps,dis-split-quirk: when set, change the way URBs are handled by the
- driver. Needed to avoid -EPROTO errors with usbhid
- on some devices (Hikey 970).
- - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
- utmi_l1_suspend_n, false when asserts utmi_sleep_n
- - snps,hird-threshold: HIRD threshold
- - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
- UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
- - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
- register for post-silicon frame length adjustment when the
- fladj_30mhz_sdbnd signal is invalid or incorrect.
- - snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode
- only. Set this and rx-max-burst-prd to a valid,
- non-zero value 1-16 (DWC_usb31 programming guide
- section 1.2.4) to enable periodic ESS RX threshold.
- - snps,rx-max-burst-prd: max periodic ESS RX burst size - host mode only. Set
- this and rx-thr-num-pkt-prd to a valid, non-zero value
- 1-16 (DWC_usb31 programming guide section 1.2.4) to
- enable periodic ESS RX threshold.
- - snps,tx-thr-num-pkt-prd: periodic ESS TX packet threshold count - host mode
- only. Set this and tx-max-burst-prd to a valid,
- non-zero value 1-16 (DWC_usb31 programming guide
- section 1.2.3) to enable periodic ESS TX threshold.
- - snps,tx-max-burst-prd: max periodic ESS TX burst size - host mode only. Set
- this and tx-thr-num-pkt-prd to a valid, non-zero value
- 1-16 (DWC_usb31 programming guide section 1.2.3) to
- enable periodic ESS TX threshold.
-
- - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.
- - snps,incr-burst-type-adjustment: Value for INCR burst type of GSBUSCFG0
- register, undefined length INCR burst type enable and INCRx type.
- When just one value, which means INCRX burst mode enabled. When
- more than one value, which means undefined length INCR burst type
- enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256.
-
- - in addition all properties from usb-xhci.txt from the current directory are
- supported as well
-
-
-This is usually a subnode to DWC3 glue to which it is connected.
-
-dwc3@4a030000 {
- compatible = "snps,dwc3";
- reg = <0x4a030000 0xcfff>;
- interrupts = <0 92 4>
- usb-phy = <&usb2_phy>, <&usb3,phy>;
- snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
-};