diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
16 files changed, 1041 insertions, 157 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.yaml b/Documentation/devicetree/bindings/net/dsa/dsa.yaml index 6107189d276a..2abd036578d1 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.yaml +++ b/Documentation/devicetree/bindings/net/dsa/dsa.yaml @@ -46,4 +46,10 @@ $defs: $ref: dsa-port.yaml# unevaluatedProperties: false +oneOf: + - required: + - ports + - required: + - ethernet-ports + ... diff --git a/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6060.yaml b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6060.yaml new file mode 100644 index 000000000000..4f1adf00431a --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6060.yaml @@ -0,0 +1,88 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6060.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MV88E6060 DSA switch + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + +description: + The Marvell MV88E6060 switch has been produced and sold by Marvell + since at least 2008. The switch has one pin ADDR4 that controls the + MDIO address of the switch to be 0x10 or 0x00, and on the MDIO bus + connected to the switch, the PHYs inside the switch appear as + independent devices on address 0x00-0x04 or 0x10-0x14, so in difference + from many other DSA switches this switch does not have an internal + MDIO bus for the PHY devices. + +properties: + compatible: + const: marvell,mv88e6060 + description: + The MV88E6060 is the oldest Marvell DSA switch product, and + as such a bit limited in features compared to later hardware. + + reg: + maxItems: 1 + + reset-gpios: + description: + GPIO to be used to reset the whole device + maxItems: 1 + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@16 { + compatible = "marvell,mv88e6060"; + reg = <16>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-port@0 { + reg = <0>; + label = "lan1"; + }; + ethernet-port@1 { + reg = <1>; + label = "lan2"; + }; + ethernet-port@2 { + reg = <2>; + label = "lan3"; + }; + ethernet-port@3 { + reg = <3>; + label = "lan4"; + }; + ethernet-port@5 { + reg = <5>; + phy-mode = "rev-mii"; + ethernet = <ðc>; + fixed-link { + speed = <100>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml new file mode 100644 index 000000000000..19f15bdd1c97 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml @@ -0,0 +1,337 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MV88E6xxx DSA switch family + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + +description: + The Marvell MV88E6xxx switch series has been produced and sold + by Marvell since at least 2008. The switch has a few compatibles which + just indicate the base address of the switch, then operating systems + can investigate switch ID registers to find out which actual version + of the switch it is dealing with. + +properties: + compatible: + oneOf: + - enum: + - marvell,mv88e6085 + - marvell,mv88e6190 + - marvell,mv88e6250 + description: | + marvell,mv88e6085: This switch uses base address 0x10. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6085" should be + specified. This includes the following list of MV88Exxxx switches: + 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, 6171, 6172, 6175, 6176, + 6185, 6240, 6320, 6321, 6341, 6350, 6351, 6352 + marvell,mv88e6190: This switch uses base address 0x00. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6190" should be + specified. This includes the following list of MV88Exxxx switches: + 6190, 6190X, 6191, 6290, 6361, 6390, 6390X + marvell,mv88e6250: This switch uses base address 0x08 or 0x18. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6250" should be + specified. This includes the following list of MV88Exxxx switches: + 6220, 6250 + - items: + - const: marvell,turris-mox-mv88e6085 + - const: marvell,mv88e6085 + - items: + - const: marvell,turris-mox-mv88e6190 + - const: marvell,mv88e6190 + + reg: + maxItems: 1 + + eeprom-length: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Set to the length of an EEPROM connected to the switch. Must be + set if the switch can not detect the presence and/or size of a connected + EEPROM, otherwise optional. + + reset-gpios: + description: + GPIO to be used to reset the whole device + maxItems: 1 + + interrupts: + description: The switch provides an external interrupt line, but it is + not always used by target systems. + maxItems: 1 + + interrupt-controller: + description: The switch has an internal interrupt controller used by + the different sub-blocks. + + '#interrupt-cells': + description: The internal interrupt controller only supports triggering + on active high level interrupts so the second cell must alway be set to + IRQ_TYPE_LEVEL_HIGH. + const: 2 + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + description: Marvell MV88E6xxx switches have an varying combination of + internal and external MDIO buses, in some cases a combined bus that + can be used both internally and externally. This node is for the + primary bus, used internally and sometimes also externally. + + mdio-external: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + description: Marvell MV88E6xxx switches that have a separate external + MDIO bus use this port to access external components on the MDIO bus. + + properties: + compatible: + const: marvell,mv88e6xxx-mdio-external + + required: + - compatible + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + sw_phy0: ethernet-phy@0 { + reg = <0x0>; + }; + + sw_phy1: ethernet-phy@1 { + reg = <0x1>; + }; + + sw_phy2: ethernet-phy@2 { + reg = <0x2>; + }; + + sw_phy3: ethernet-phy@3 { + reg = <0x3>; + }; + }; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-port@0 { + reg = <0>; + label = "lan4"; + phy-handle = <&sw_phy0>; + phy-mode = "internal"; + }; + + ethernet-port@1 { + reg = <1>; + label = "lan3"; + phy-handle = <&sw_phy1>; + phy-mode = "internal"; + }; + + ethernet-port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&sw_phy2>; + phy-mode = "internal"; + }; + + ethernet-port@3 { + reg = <3>; + label = "lan1"; + phy-handle = <&sw_phy3>; + phy-mode = "internal"; + }; + + ethernet-port@5 { + reg = <5>; + ethernet = <&fec>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@0 { + compatible = "marvell,mv88e6190"; + #interrupt-cells = <2>; + interrupt-controller; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&switch_interrupt_pins>; + pinctrl-names = "default"; + reg = <0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch0phy1: ethernet-phy@1 { + reg = <0x1>; + }; + + switch0phy2: ethernet-phy@2 { + reg = <0x2>; + }; + + switch0phy3: ethernet-phy@3 { + reg = <0x3>; + }; + + switch0phy4: ethernet-phy@4 { + reg = <0x4>; + }; + + switch0phy5: ethernet-phy@5 { + reg = <0x5>; + }; + + switch0phy6: ethernet-phy@6 { + reg = <0x6>; + }; + + switch0phy7: ethernet-phy@7 { + reg = <0x7>; + }; + + switch0phy8: ethernet-phy@8 { + reg = <0x8>; + }; + }; + + mdio-external { + compatible = "marvell,mv88e6xxx-mdio-external"; + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@b { + reg = <0xb>; + compatible = "ethernet-phy-ieee802.3-c45"; + }; + + phy2: ethernet-phy@c { + reg = <0xc>; + compatible = "ethernet-phy-ieee802.3-c45"; + }; + }; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-port@0 { + ethernet = <ð0>; + phy-mode = "rgmii"; + reg = <0>; + + fixed-link { + full-duplex; + pause; + speed = <1000>; + }; + }; + + ethernet-port@1 { + label = "lan1"; + phy-handle = <&switch0phy1>; + reg = <1>; + }; + + ethernet-port@2 { + label = "lan2"; + phy-handle = <&switch0phy2>; + reg = <2>; + }; + + ethernet-port@3 { + label = "lan3"; + phy-handle = <&switch0phy3>; + reg = <3>; + }; + + ethernet-port@4 { + label = "lan4"; + phy-handle = <&switch0phy4>; + reg = <4>; + }; + + ethernet-port@5 { + label = "lan5"; + phy-handle = <&switch0phy5>; + reg = <5>; + }; + + ethernet-port@6 { + label = "lan6"; + phy-handle = <&switch0phy6>; + reg = <6>; + }; + + ethernet-port@7 { + label = "lan7"; + phy-handle = <&switch0phy7>; + reg = <7>; + }; + + ethernet-port@8 { + label = "lan8"; + phy-handle = <&switch0phy8>; + reg = <8>; + }; + + ethernet-port@9 { + /* 88X3310P external phy */ + label = "lan9"; + phy-handle = <&phy1>; + phy-mode = "xaui"; + reg = <9>; + }; + + ethernet-port@a { + /* 88X3310P external phy */ + label = "lan10"; + phy-handle = <&phy2>; + phy-mode = "xaui"; + reg = <0xa>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt deleted file mode 100644 index 6ec0c181b6db..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/marvell.txt +++ /dev/null @@ -1,109 +0,0 @@ -Marvell DSA Switch Device Tree Bindings ---------------------------------------- - -WARNING: This binding is currently unstable. Do not program it into a -FLASH never to be changed again. Once this binding is stable, this -warning will be removed. - -If you need a stable binding, use the old dsa.txt binding. - -Marvell Switches are MDIO devices. The following properties should be -placed as a child node of an mdio device. - -The properties described here are those specific to Marvell devices. -Additional required and optional properties can be found in dsa.txt. - -The compatibility string is used only to find an identification register, -which is at a different MDIO base address in different switch families. -- "marvell,mv88e6085" : Switch has base address 0x10. Use with models: - 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, - 6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321, - 6341, 6350, 6351, 6352 -- "marvell,mv88e6190" : Switch has base address 0x00. Use with models: - 6190, 6190X, 6191, 6290, 6361, 6390, 6390X -- "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model: - 6220, 6250 - -Required properties: -- compatible : Should be one of "marvell,mv88e6085", - "marvell,mv88e6190" or "marvell,mv88e6250" as - indicated above -- reg : Address on the MII bus for the switch. - -Optional properties: - -- reset-gpios : Should be a gpio specifier for a reset line -- interrupts : Interrupt from the switch -- interrupt-controller : Indicates the switch is itself an interrupt - controller. This is used for the PHY interrupts. -#interrupt-cells = <2> : Controller uses two cells, number and flag -- eeprom-length : Set to the length of an EEPROM connected to the - switch. Must be set if the switch can not detect - the presence and/or size of a connected EEPROM, - otherwise optional. -- mdio : Container of PHY and devices on the switches MDIO - bus. -- mdio? : Container of PHYs and devices on the external MDIO - bus. The node must contains a compatible string of - "marvell,mv88e6xxx-mdio-external" - -Example: - - mdio { - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&gpio0>; - interrupts = <27 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <2>; - - switch0: switch@0 { - compatible = "marvell,mv88e6085"; - reg = <0>; - reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - switch1phy0: switch1phy0@0 { - reg = <0>; - interrupt-parent = <&switch0>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; - }; - }; - }; - }; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&gpio0>; - interrupts = <27 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <2>; - - switch0: switch@0 { - compatible = "marvell,mv88e6190"; - reg = <0>; - reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - switch1phy0: switch1phy0@0 { - reg = <0>; - interrupt-parent = <&switch0>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; - }; - }; - - mdio1 { - compatible = "marvell,mv88e6xxx-mdio-external"; - #address-cells = <1>; - #size-cells = <0>; - switch1phy9: switch1phy0@9 { - reg = <9>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml index b3029c64d0d5..c963dc09e8e1 100644 --- a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml +++ b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml @@ -11,7 +11,6 @@ maintainers: - Woojung Huh <Woojung.Huh@microchip.com> allOf: - - $ref: dsa.yaml#/$defs/ethernet-ports - $ref: /schemas/spi/spi-peripheral-props.yaml# properties: @@ -78,6 +77,39 @@ required: - compatible - reg +if: + not: + properties: + compatible: + enum: + - microchip,ksz8863 + - microchip,ksz8873 +then: + $ref: dsa.yaml#/$defs/ethernet-ports +else: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-2]$": + $ref: dsa-port.yaml# + unevaluatedProperties: false + properties: + microchip,rmii-clk-internal: + $ref: /schemas/types.yaml#/definitions/flag + description: + When ksz88x3 is acting as clock provier (via REFCLKO) it + can select between internal and external RMII reference + clock. Internal reference clock means that the clock for + the RMII of ksz88x3 is provided by the ksz88x3 internally + and the REFCLKI pin is unconnected. For the external + reference clock, the clock needs to be fed back to ksz88x3 + via REFCLKI. + If microchip,rmii-clk-internal is set, ksz88x3 will provide + rmii reference clock internally, otherwise reference clock + should be provided externally. + dependencies: + microchip,rmii-clk-internal: [ethernet] + unevaluatedProperties: false examples: diff --git a/Documentation/devicetree/bindings/net/ethernet-switch.yaml b/Documentation/devicetree/bindings/net/ethernet-switch.yaml index 72ac67ca3415..b3b7e1a1b127 100644 --- a/Documentation/devicetree/bindings/net/ethernet-switch.yaml +++ b/Documentation/devicetree/bindings/net/ethernet-switch.yaml @@ -20,9 +20,26 @@ description: select: false -properties: - $nodename: - pattern: "^(ethernet-)?switch(@.*)?$" +allOf: + # This condition is here to satisfy the case where certain device + # nodes have to preserve non-standard names because of + # backward-compatibility with boot loaders inspecting certain + # node names. + - if: + properties: + compatible: + contains: + enum: + - marvell,turris-mox-mv88e6085 + - marvell,turris-mox-mv88e6190 + then: + properties: + $nodename: + pattern: "switch[0-3]@[0-3]+$" + else: + properties: + $nodename: + pattern: "^(ethernet-)?switch(@.*)?$" patternProperties: "^(ethernet-)?ports$": diff --git a/Documentation/devicetree/bindings/net/lantiq,pef2256.yaml b/Documentation/devicetree/bindings/net/lantiq,pef2256.yaml new file mode 100644 index 000000000000..7da8370e2468 --- /dev/null +++ b/Documentation/devicetree/bindings/net/lantiq,pef2256.yaml @@ -0,0 +1,213 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/lantiq,pef2256.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Lantiq PEF2256 + +maintainers: + - Herve Codina <herve.codina@bootlin.com> + +description: + The Lantiq PEF2256, also known as Infineon PEF2256 or FALC56, is a framer and + line interface component designed to fulfill all required interfacing between + an analog E1/T1/J1 line and the digital PCM system highway/H.100 bus. + +properties: + compatible: + items: + - const: lantiq,pef2256 + + reg: + maxItems: 1 + + clocks: + items: + - description: Master Clock + - description: System Clock Receive + - description: System Clock Transmit + + clock-names: + items: + - const: mclk + - const: sclkr + - const: sclkx + + interrupts: + maxItems: 1 + + reset-gpios: + description: + GPIO used to reset the device. + maxItems: 1 + + pinctrl: + $ref: /schemas/pinctrl/pinctrl.yaml# + additionalProperties: false + + patternProperties: + '-pins$': + type: object + $ref: /schemas/pinctrl/pinmux-node.yaml# + additionalProperties: false + + properties: + pins: + enum: [ RPA, RPB, RPC, RPD, XPA, XPB, XPC, XPD ] + + function: + enum: [ SYPR, RFM, RFMB, RSIGM, RSIG, DLR, FREEZE, RFSP, LOS, + SYPX, XFMS, XSIG, TCLK, XMFB, XSIGM, DLX, XCLK, XLT, + GPI, GPOH, GPOL ] + + required: + - pins + - function + + lantiq,data-rate-bps: + enum: [2048000, 4096000, 8192000, 16384000] + default: 2048000 + description: + Data rate (bit per seconds) on the system highway. + + lantiq,clock-falling-edge: + $ref: /schemas/types.yaml#/definitions/flag + description: + Data is sent on falling edge of the clock (and received on the rising + edge). If 'clock-falling-edge' is not present, data is sent on the + rising edge (and received on the falling edge). + + lantiq,channel-phase: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5, 6, 7] + default: 0 + description: | + The pef2256 delivers a full frame (32 8-bit time-slots in E1 and 24 8-bit + time-slots 8 8-bit signaling in E1/J1) every 125us. This lead to a data + rate of 2048000 bit/s. When lantiq,data-rate-bps is more than 2048000 + bit/s, the data (all 32 8-bit) present in the frame are interleave with + unused time-slots. The lantiq,channel-phase property allows to set the + correct alignment of the interleave mechanism. + For instance, suppose lantiq,data-rate-bps = 8192000 (ie 4*2048000), and + lantiq,channel-phase = 2, the interleave schema with unused time-slots + (nu) and used time-slots (XX) for TSi is + nu nu XX nu nu nu XX nu nu nu XX nu + <-- TSi --> <- TSi+1 -> <- TSi+2 -> + With lantiq,data-rate-bps = 8192000, and lantiq,channel-phase = 1, the + interleave schema is + nu XX nu nu nu XX nu nu nu XX nu nu + <-- TSi --> <- TSi+1 -> <- TSi+2 -> + With lantiq,data-rate-bps = 4096000 (ie 2*2048000), and + lantiq,channel-phase = 1, the interleave schema is + nu XX nu XX nu XX + <-- TSi --> <- TSi+1 -> <- TSi+2 -> + +patternProperties: + '^codec(-([0-9]|[1-2][0-9]|3[0-1]))?$': + type: object + $ref: /schemas/sound/dai-common.yaml + unevaluatedProperties: false + description: + Codec provided by the pef2256. This codec allows to use some of the PCM + system highway time-slots as audio channels to transport audio data over + the E1/T1/J1 lines. + The time-slots used by the codec must be set and so, the properties + 'dai-tdm-slot-num', 'dai-tdm-slot-width', 'dai-tdm-slot-tx-mask' and + 'dai-tdm-slot-rx-mask' must be present in the sound card node for + sub-nodes that involve the codec. The codec uses 8-bit time-slots. + 'dai-tdm-tdm-slot-with' must be set to 8. + The tx and rx masks define the pef2256 time-slots assigned to the codec. + + properties: + compatible: + const: lantiq,pef2256-codec + + '#sound-dai-cells': + const: 0 + + required: + - compatible + - '#sound-dai-cells' + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + pef2256: framer@2000000 { + compatible = "lantiq,pef2256"; + reg = <0x2000000 0x100>; + interrupts = <8 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&intc>; + clocks = <&clk_mclk>, <&clk_sclkr>, <&clk_sclkx>; + clock-names = "mclk", "sclkr", "sclkx"; + reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + lantiq,data-rate-bps = <4096000>; + + pinctrl { + pef2256_rpa_sypr: rpa-pins { + pins = "RPA"; + function = "SYPR"; + }; + pef2256_xpa_sypx: xpa-pins { + pins = "XPA"; + function = "SYPX"; + }; + }; + + pef2256_codec0: codec-0 { + compatible = "lantiq,pef2256-codec"; + #sound-dai-cells = <0>; + sound-name-prefix = "PEF2256_0"; + }; + + pef2256_codec1: codec-1 { + compatible = "lantiq,pef2256-codec"; + #sound-dai-cells = <0>; + sound-name-prefix = "PEF2256_1"; + }; + }; + + sound { + compatible = "simple-audio-card"; + #address-cells = <1>; + #size-cells = <0>; + simple-audio-card,dai-link@0 { /* CPU DAI1 - pef2256 codec 1 */ + reg = <0>; + cpu { + sound-dai = <&cpu_dai1>; + }; + codec { + sound-dai = <&pef2256_codec0>; + dai-tdm-slot-num = <4>; + dai-tdm-slot-width = <8>; + /* TS 1, 2, 3, 4 */ + dai-tdm-slot-tx-mask = <0 1 1 1 1>; + dai-tdm-slot-rx-mask = <0 1 1 1 1>; + }; + }; + simple-audio-card,dai-link@1 { /* CPU DAI2 - pef2256 codec 2 */ + reg = <1>; + cpu { + sound-dai = <&cpu_dai2>; + }; + codec { + sound-dai = <&pef2256_codec1>; + dai-tdm-slot-num = <4>; + dai-tdm-slot-width = <8>; + /* TS 5, 6, 7, 8 */ + dai-tdm-slot-tx-mask = <0 0 0 0 0 1 1 1 1>; + dai-tdm-slot-rx-mask = <0 0 0 0 0 1 1 1 1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/marvell,aquantia.yaml b/Documentation/devicetree/bindings/net/marvell,aquantia.yaml new file mode 100644 index 000000000000..9854fab4c4db --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell,aquantia.yaml @@ -0,0 +1,116 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/marvell,aquantia.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell Aquantia Ethernet PHY + +maintainers: + - Christian Marangi <ansuelsmth@gmail.com> + +description: | + Marvell Aquantia Ethernet PHY require a firmware to be loaded to actually + work. + + This can be done and is implemented by OEM in 3 different way: + - Attached SPI flash directly to the PHY with the firmware. The PHY + will self load the firmware in the presence of this configuration. + - Read from a dedicated partition on system NAND declared in an + NVMEM cell, and loaded to the PHY using its mailbox interface. + - Manually provided firmware loaded from a file in the filesystem. + +allOf: + - $ref: ethernet-phy.yaml# + +select: + properties: + compatible: + contains: + enum: + - ethernet-phy-id03a1.b445 + - ethernet-phy-id03a1.b460 + - ethernet-phy-id03a1.b4a2 + - ethernet-phy-id03a1.b4d0 + - ethernet-phy-id03a1.b4e0 + - ethernet-phy-id03a1.b5c2 + - ethernet-phy-id03a1.b4b0 + - ethernet-phy-id03a1.b662 + - ethernet-phy-id03a1.b712 + - ethernet-phy-id31c3.1c12 + required: + - compatible + +properties: + reg: + maxItems: 1 + + firmware-name: + description: specify the name of PHY firmware to load + + nvmem-cells: + description: phandle to the firmware nvmem cell + maxItems: 1 + + nvmem-cell-names: + const: firmware + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-phy@0 { + compatible = "ethernet-phy-id31c3.1c12", + "ethernet-phy-ieee802.3-c45"; + + reg = <0>; + firmware-name = "AQR-G4_v5.4.C-AQR_CIG_WF-1945_0x8_ID44776_VER1630.cld"; + }; + + ethernet-phy@1 { + compatible = "ethernet-phy-id31c3.1c12", + "ethernet-phy-ieee802.3-c45"; + + reg = <1>; + nvmem-cells = <&aqr_fw>; + nvmem-cell-names = "firmware"; + }; + }; + + flash { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + /* ... */ + + partition@650000 { + compatible = "nvmem-cells"; + label = "0:ethphyfw"; + reg = <0x650000 0x80000>; + read-only; + #address-cells = <1>; + #size-cells = <1>; + + aqr_fw: aqr_fw@0 { + reg = <0x0 0x5f42a>; + }; + }; + + /* ... */ + + }; + }; diff --git a/Documentation/devicetree/bindings/net/marvell,mvusb.yaml b/Documentation/devicetree/bindings/net/marvell,mvusb.yaml index 3a3325168048..ab838c1ffeed 100644 --- a/Documentation/devicetree/bindings/net/marvell,mvusb.yaml +++ b/Documentation/devicetree/bindings/net/marvell,mvusb.yaml @@ -50,11 +50,14 @@ examples: #address-cells = <1>; #size-cells = <0>; - switch@0 { + ethernet-switch@0 { compatible = "marvell,mv88e6190"; reg = <0x0>; - ports { + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + /* Port definitions */ }; diff --git a/Documentation/devicetree/bindings/net/marvell,orion-mdio.yaml b/Documentation/devicetree/bindings/net/marvell,orion-mdio.yaml index e35da8b01dc2..73429855d584 100644 --- a/Documentation/devicetree/bindings/net/marvell,orion-mdio.yaml +++ b/Documentation/devicetree/bindings/net/marvell,orion-mdio.yaml @@ -39,28 +39,6 @@ required: allOf: - $ref: mdio.yaml# - - if: - required: - - interrupts - - then: - properties: - reg: - items: - - items: - - $ref: /schemas/types.yaml#/definitions/cell - - const: 0x84 - - else: - properties: - reg: - items: - - items: - - $ref: /schemas/types.yaml#/definitions/cell - - enum: - - 0x4 - - 0x10 - unevaluatedProperties: false examples: diff --git a/Documentation/devicetree/bindings/net/pcs/mediatek,sgmiisys.yaml b/Documentation/devicetree/bindings/net/pcs/mediatek,sgmiisys.yaml index 66a95191bd77..1bacc0eeff75 100644 --- a/Documentation/devicetree/bindings/net/pcs/mediatek,sgmiisys.yaml +++ b/Documentation/devicetree/bindings/net/pcs/mediatek,sgmiisys.yaml @@ -15,15 +15,22 @@ description: properties: compatible: - items: - - enum: - - mediatek,mt7622-sgmiisys - - mediatek,mt7629-sgmiisys - - mediatek,mt7981-sgmiisys_0 - - mediatek,mt7981-sgmiisys_1 - - mediatek,mt7986-sgmiisys_0 - - mediatek,mt7986-sgmiisys_1 - - const: syscon + oneOf: + - items: + - enum: + - mediatek,mt7622-sgmiisys + - mediatek,mt7629-sgmiisys + - mediatek,mt7981-sgmiisys_0 + - mediatek,mt7981-sgmiisys_1 + - mediatek,mt7986-sgmiisys_0 + - mediatek,mt7986-sgmiisys_1 + - const: syscon + - items: + - enum: + - mediatek,mt7988-sgmiisys0 + - mediatek,mt7988-sgmiisys1 + - const: simple-mfd + - const: syscon reg: maxItems: 1 @@ -35,11 +42,51 @@ properties: description: Invert polarity of the SGMII data lanes type: boolean + pcs: + type: object + description: MediaTek LynxI HSGMII PCS + properties: + compatible: + const: mediatek,mt7988-sgmii + + clocks: + maxItems: 3 + + clock-names: + items: + - const: sgmii_sel + - const: sgmii_tx + - const: sgmii_rx + + required: + - compatible + - clocks + - clock-names + + additionalProperties: false + required: - compatible - reg - '#clock-cells' +allOf: + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt7988-sgmiisys0 + - mediatek,mt7988-sgmiisys1 + + then: + required: + - pcs + + else: + properties: + pcs: false + additionalProperties: false examples: diff --git a/Documentation/devicetree/bindings/net/qcom,ipa.yaml b/Documentation/devicetree/bindings/net/qcom,ipa.yaml index 2d5e4ffb2f9e..c30218684cfe 100644 --- a/Documentation/devicetree/bindings/net/qcom,ipa.yaml +++ b/Documentation/devicetree/bindings/net/qcom,ipa.yaml @@ -43,15 +43,21 @@ description: properties: compatible: - enum: - - qcom,msm8998-ipa - - qcom,sc7180-ipa - - qcom,sc7280-ipa - - qcom,sdm845-ipa - - qcom,sdx55-ipa - - qcom,sdx65-ipa - - qcom,sm6350-ipa - - qcom,sm8350-ipa + oneOf: + - enum: + - qcom,msm8998-ipa + - qcom,sc7180-ipa + - qcom,sc7280-ipa + - qcom,sdm845-ipa + - qcom,sdx55-ipa + - qcom,sdx65-ipa + - qcom,sm6350-ipa + - qcom,sm8350-ipa + - qcom,sm8550-ipa + - items: + - enum: + - qcom,sm8650-ipa + - const: qcom,sm8550-ipa reg: items: diff --git a/Documentation/devicetree/bindings/net/renesas,etheravb.yaml b/Documentation/devicetree/bindings/net/renesas,etheravb.yaml index 5d074f27d462..890f7858d0dc 100644 --- a/Documentation/devicetree/bindings/net/renesas,etheravb.yaml +++ b/Documentation/devicetree/bindings/net/renesas,etheravb.yaml @@ -55,9 +55,10 @@ properties: - items: - enum: - - renesas,r9a07g043-gbeth # RZ/G2UL + - renesas,r9a07g043-gbeth # RZ/G2UL and RZ/Five - renesas,r9a07g044-gbeth # RZ/G2{L,LC} - renesas,r9a07g054-gbeth # RZ/V2L + - renesas,r9a08g045-gbeth # RZ/G3S - const: renesas,rzg2l-gbeth # RZ/{G2L,G2UL,V2L} family reg: true diff --git a/Documentation/devicetree/bindings/net/renesas,ethertsn.yaml b/Documentation/devicetree/bindings/net/renesas,ethertsn.yaml new file mode 100644 index 000000000000..475aff7714d6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/renesas,ethertsn.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/renesas,ethertsn.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas Ethernet TSN End-station + +maintainers: + - Niklas Söderlund <niklas.soderlund@ragnatech.se> + +description: + The RTSN device provides Ethernet network using a 10 Mbps, 100 Mbps, or 1 + Gbps full-duplex link via MII/GMII/RMII/RGMII. Depending on the connected PHY. + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + items: + - enum: + - renesas,r8a779g0-ethertsn # R-Car V4H + - const: renesas,rcar-gen4-ethertsn + + reg: + items: + - description: TSN End Station target + - description: generalized Precision Time Protocol target + + reg-names: + items: + - const: tsnes + - const: gptp + + interrupts: + items: + - description: TX data interrupt + - description: RX data interrupt + + interrupt-names: + items: + - const: tx + - const: rx + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + phy-mode: + contains: + enum: + - mii + - rgmii + + phy-handle: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Specifies a reference to a node representing a PHY device. + + rx-internal-delay-ps: + enum: [0, 1800] + + tx-internal-delay-ps: + enum: [0, 2000] + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +patternProperties: + "^ethernet-phy@[0-9a-f]$": + type: object + $ref: ethernet-phy.yaml# + unevaluatedProperties: false + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-names + - clocks + - power-domains + - resets + - phy-mode + - phy-handle + - '#address-cells' + - '#size-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a779g0-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a779g0-sysc.h> + #include <dt-bindings/gpio/gpio.h> + + tsn0: ethernet@e6460000 { + compatible = "renesas,r8a779g0-ethertsn", "renesas,rcar-gen4-ethertsn"; + reg = <0xe6460000 0x7000>, + <0xe6449000 0x500>; + reg-names = "tsnes", "gptp"; + interrupts = <GIC_SPI 429 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx", "rx"; + clocks = <&cpg CPG_MOD 2723>; + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>; + resets = <&cpg 2723>; + + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + phy-handle = <&phy3>; + + #address-cells = <1>; + #size-cells = <0>; + + phy3: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0>; + interrupt-parent = <&gpio4>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/sff,sfp.yaml b/Documentation/devicetree/bindings/net/sff,sfp.yaml index 973e478a399d..bf6cbc7c2ba3 100644 --- a/Documentation/devicetree/bindings/net/sff,sfp.yaml +++ b/Documentation/devicetree/bindings/net/sff,sfp.yaml @@ -120,7 +120,7 @@ examples: pinctrl-names = "default"; pinctrl-0 = <&cps_sfpp0_pins>; tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>; - tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>; }; mdio { diff --git a/Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml b/Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml index 1d33d80af11c..bbe89ea9590c 100644 --- a/Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml +++ b/Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml @@ -122,6 +122,20 @@ properties: and "phy-handle" should point to an external PHY if exists. maxItems: 1 + dmas: + minItems: 2 + maxItems: 32 + description: TX and RX DMA channel phandle + + dma-names: + items: + pattern: "^[tr]x_chan([0-9]|1[0-5])$" + description: + Should be "tx_chan0", "tx_chan1" ... "tx_chan15" for DMA Tx channel + Should be "rx_chan0", "rx_chan1" ... "rx_chan15" for DMA Rx channel + minItems: 2 + maxItems: 32 + required: - compatible - interrupts @@ -143,6 +157,8 @@ examples: clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>; phy-mode = "mii"; reg = <0x40c00000 0x40000>,<0x50c00000 0x40000>; + dmas = <&xilinx_dma 0>, <&xilinx_dma 1>; + dma-names = "tx_chan0", "rx_chan0"; xlnx,rxcsum = <0x2>; xlnx,rxmem = <0x800>; xlnx,txcsum = <0x2>; |