Merge 3.2-rc3 into tty-next to handle merge conflict in tty_ldisc.c

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

6 files changed, 46 insertions, 36 deletions

diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 45c5758f7690..705d2dc39c9a 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1581,7 +1581,7 @@ config SERIAL_IFX6X60
 	  Support for the IFX6x60 modem devices on Intel MID platforms.
 
 config SERIAL_PCH_UART
-	tristate "Intel EG20T PCH / OKI SEMICONDUCTOR IOH(ML7213/ML7223) UART"
+	tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) UART"
 	depends on PCI
 	select SERIAL_CORE
 	help
@@ -1589,12 +1589,12 @@ config SERIAL_PCH_UART
 	  which is an IOH(Input/Output Hub) for x86 embedded processor.
 	  Enabling PCH_DMA, this PCH UART works as DMA mode.
 
-	  This driver also can be used for OKI SEMICONDUCTOR IOH(Input/
-	  Output Hub), ML7213 and ML7223.
-	  ML7213 IOH is for IVI(In-Vehicle Infotainment) use and ML7223 IOH is
-	  for MP(Media Phone) use.
-	  ML7213/ML7223 is companion chip for Intel Atom E6xx series.
-	  ML7213/ML7223 is completely compatible for Intel EG20T PCH.
+	  This driver also can be used for LAPIS Semiconductor IOH(Input/
+	  Output Hub), ML7213, ML7223 and ML7831.
+	  ML7213 IOH is for IVI(In-Vehicle Infotainment) use, ML7223 IOH is
+	  for MP(Media Phone) use and ML7831 IOH is for general purpose use.
+	  ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series.
+	  ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH.
 
 config SERIAL_PCH_UART_CONSOLE
 	bool "Support for console on Intel EG20T PCH UART/OKI SEMICONDUCTOR ML7213 IOH"
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 6b844d422578..bd85e32521d2 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -228,7 +228,7 @@ void atmel_config_rs485(struct uart_port *port, struct serial_rs485 *rs485conf)
 	if (rs485conf->flags & SER_RS485_ENABLED) {
 		dev_dbg(port->dev, "Setting UART to RS485\n");
 		atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
-		if (rs485conf->flags & SER_RS485_RTS_AFTER_SEND)
+		if ((rs485conf->delay_rts_after_send) > 0)
 			UART_PUT_TTGR(port, rs485conf->delay_rts_after_send);
 		mode |= ATMEL_US_USMODE_RS485;
 	} else {
@@ -304,7 +304,7 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
 
 	if (atmel_port->rs485.flags & SER_RS485_ENABLED) {
 		dev_dbg(port->dev, "Setting UART to RS485\n");
-		if (atmel_port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
+		if ((atmel_port->rs485.delay_rts_after_send) > 0)
 			UART_PUT_TTGR(port,
 					atmel_port->rs485.delay_rts_after_send);
 		mode |= ATMEL_US_USMODE_RS485;
@@ -1228,7 +1228,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
 
 	if (atmel_port->rs485.flags & SER_RS485_ENABLED) {
 		dev_dbg(port->dev, "Setting UART to RS485\n");
-		if (atmel_port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
+		if ((atmel_port->rs485.delay_rts_after_send) > 0)
 			UART_PUT_TTGR(port,
 					atmel_port->rs485.delay_rts_after_send);
 		mode |= ATMEL_US_USMODE_RS485;
@@ -1442,16 +1442,6 @@ static void __devinit atmel_of_init_port(struct atmel_uart_port *atmel_port,
 		rs485conf->delay_rts_after_send = rs485_delay[1];
 		rs485conf->flags = 0;
 
-		if (rs485conf->delay_rts_before_send == 0 &&
-		    rs485conf->delay_rts_after_send == 0) {
-			rs485conf->flags |= SER_RS485_RTS_ON_SEND;
-		} else {
-			if (rs485conf->delay_rts_before_send)
-				rs485conf->flags |= SER_RS485_RTS_BEFORE_SEND;
-			if (rs485conf->delay_rts_after_send)
-				rs485conf->flags |= SER_RS485_RTS_AFTER_SEND;
-		}
-
 		if (of_get_property(np, "rs485-rx-during-tx", NULL))
 			rs485conf->flags |= SER_RS485_RX_DURING_TX;
 
diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c
index b7435043f2fe..1dfba7b779c8 100644
--- a/drivers/tty/serial/crisv10.c
+++ b/drivers/tty/serial/crisv10.c
@@ -3234,9 +3234,8 @@ rs_write(struct tty_struct *tty,
 		e100_disable_rx(info);
 		e100_enable_rx_irq(info);
 #endif
-		if ((info->rs485.flags & SER_RS485_RTS_BEFORE_SEND) &&
-			(info->rs485.delay_rts_before_send > 0))
-				msleep(info->rs485.delay_rts_before_send);
+		if (info->rs485.delay_rts_before_send > 0)
+			msleep(info->rs485.delay_rts_before_send);
 	}
 #endif /* CONFIG_ETRAX_RS485 */
 
@@ -3693,10 +3692,6 @@ rs_ioctl(struct tty_struct *tty,
 
 		rs485data.delay_rts_before_send = rs485ctrl.delay_rts_before_send;
 		rs485data.flags = 0;
-		if (rs485data.delay_rts_before_send != 0)
-			rs485data.flags |= SER_RS485_RTS_BEFORE_SEND;
-		else
-			rs485data.flags &= ~(SER_RS485_RTS_BEFORE_SEND);
 
 		if (rs485ctrl.enabled)
 			rs485data.flags |= SER_RS485_ENABLED;
@@ -4531,7 +4526,6 @@ static int __init rs_init(void)
 		/* Set sane defaults */
 		info->rs485.flags &= ~(SER_RS485_RTS_ON_SEND);
 		info->rs485.flags |= SER_RS485_RTS_AFTER_SEND;
-		info->rs485.flags &= ~(SER_RS485_RTS_BEFORE_SEND);
 		info->rs485.delay_rts_before_send = 0;
 		info->rs485.flags &= ~(SER_RS485_ENABLED);
 #endif
diff --git a/drivers/tty/serial/mfd.c b/drivers/tty/serial/mfd.c
index 565f3fe3dd77..a9234ba8f8d5 100644
--- a/drivers/tty/serial/mfd.c
+++ b/drivers/tty/serial/mfd.c
@@ -884,7 +884,6 @@ serial_hsu_set_termios(struct uart_port *port, struct ktermios *termios,
 {
 	struct uart_hsu_port *up =
 			container_of(port, struct uart_hsu_port, port);
-	struct tty_struct *tty = port->state->port.tty;
 	unsigned char cval, fcr = 0;
 	unsigned long flags;
 	unsigned int baud, quot;
@@ -907,8 +906,7 @@ serial_hsu_set_termios(struct uart_port *port, struct ktermios *termios,
 	}
 
 	/* CMSPAR isn't supported by this driver */
-	if (tty)
-		tty->termios->c_cflag &= ~CMSPAR;
+	termios->c_cflag &= ~CMSPAR;
 
 	if (termios->c_cflag & CSTOPB)
 		cval |= UART_LCR_STOP;
diff --git a/drivers/tty/serial/pch_uart.c b/drivers/tty/serial/pch_uart.c
index b950d059a781..de0f613ed6f5 100644
--- a/drivers/tty/serial/pch_uart.c
+++ b/drivers/tty/serial/pch_uart.c
@@ -1,5 +1,5 @@
 /*
- *Copyright (C) 2010 OKI SEMICONDUCTOR CO., LTD.
+ *Copyright (C) 2011 LAPIS Semiconductor Co., Ltd.
  *
  *This program is free software; you can redistribute it and/or modify
  *it under the terms of the GNU General Public License as published by
@@ -49,8 +49,8 @@ enum {
 
 /* Set the max number of UART port
  * Intel EG20T PCH: 4 port
- * OKI SEMICONDUCTOR ML7213 IOH: 3 port
- * OKI SEMICONDUCTOR ML7223 IOH: 2 port
+ * LAPIS Semiconductor ML7213 IOH: 3 port
+ * LAPIS Semiconductor ML7223 IOH: 2 port
 */
 #define PCH_UART_NR	4
 
@@ -265,6 +265,8 @@ enum pch_uart_num_t {
 	pch_ml7213_uart2,
 	pch_ml7223_uart0,
 	pch_ml7223_uart1,
+	pch_ml7831_uart0,
+	pch_ml7831_uart1,
 };
 
 static struct pch_uart_driver_data drv_dat[] = {
@@ -277,6 +279,8 @@ static struct pch_uart_driver_data drv_dat[] = {
 	[pch_ml7213_uart2] = {PCH_UART_2LINE, 2},
 	[pch_ml7223_uart0] = {PCH_UART_8LINE, 0},
 	[pch_ml7223_uart1] = {PCH_UART_2LINE, 1},
+	[pch_ml7831_uart0] = {PCH_UART_8LINE, 0},
+	[pch_ml7831_uart1] = {PCH_UART_2LINE, 1},
 };
 
 #ifdef CONFIG_SERIAL_PCH_UART_CONSOLE
@@ -638,6 +642,7 @@ static void pch_request_dma(struct uart_port *port)
 		dev_err(priv->port.dev, "%s:dma_request_channel FAILS(Rx)\n",
 			__func__);
 		dma_release_channel(priv->chan_tx);
+		priv->chan_tx = NULL;
 		return;
 	}
 
@@ -1225,8 +1230,7 @@ static void pch_uart_shutdown(struct uart_port *port)
 		dev_err(priv->port.dev,
 			"pch_uart_hal_set_fifo Failed(ret=%d)\n", ret);
 
-	if (priv->use_dma_flag)
-		pch_free_dma(port);
+	pch_free_dma(port);
 
 	free_irq(priv->port.irq, priv);
 }
@@ -1290,6 +1294,7 @@ static void pch_uart_set_termios(struct uart_port *port,
 	if (rtn)
 		goto out;
 
+	pch_uart_set_mctrl(&priv->port, priv->port.mctrl);
 	/* Don't rewrite B0 */
 	if (tty_termios_baud_rate(termios))
 		tty_termios_encode_baud_rate(termios, baud, baud);
@@ -1710,6 +1715,10 @@ static DEFINE_PCI_DEVICE_TABLE(pch_uart_pci_id) = {
 	 .driver_data = pch_ml7223_uart0},
 	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x800D),
 	 .driver_data = pch_ml7223_uart1},
+	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8811),
+	 .driver_data = pch_ml7831_uart0},
+	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8812),
+	 .driver_data = pch_ml7831_uart1},
 	{0,},
 };
 
diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index 1945c70539c2..aff9d612dff0 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -207,6 +207,25 @@ static struct plat_sci_reg sci_regmap[SCIx_NR_REGTYPES][SCIx_NR_REGS] = {
 	},
 
 	/*
+	 * Common SH-2(A) SCIF definitions for ports with FIFO data
+	 * count registers.
+	 */
+	[SCIx_SH2_SCIF_FIFODATA_REGTYPE] = {
+		[SCSMR]		= { 0x00, 16 },
+		[SCBRR]		= { 0x04,  8 },
+		[SCSCR]		= { 0x08, 16 },
+		[SCxTDR]	= { 0x0c,  8 },
+		[SCxSR]		= { 0x10, 16 },
+		[SCxRDR]	= { 0x14,  8 },
+		[SCFCR]		= { 0x18, 16 },
+		[SCFDR]		= { 0x1c, 16 },
+		[SCTFDR]	= sci_reg_invalid,
+		[SCRFDR]	= sci_reg_invalid,
+		[SCSPTR]	= { 0x20, 16 },
+		[SCLSR]		= { 0x24, 16 },
+	},
+
+	/*
 	 * Common SH-3 SCIF definitions.
 	 */
 	[SCIx_SH3_SCIF_REGTYPE] = {