iio: st_sensors: support open drain mode

Some types of ST Sensors can be connected to the same IRQ line
as other peripherals using open drain. Add a device tree binding
and a sensor data property to flip the right bit in the interrupt
control register to enable open drain mode on the INT line.

If the line is set to be open drain, also tag on IRQF_SHARED
to the IRQ flags when requesting the interrupt, as the whole
point of using open drain interrupt lines is to share them with
more than one peripheral (wire-or).

Cc: devicetree@vger.kernel.org
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Rob Herring <rob@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

2 files changed, 33 insertions, 0 deletions

diff --git a/drivers/iio/common/st_sensors/st_sensors_core.c b/drivers/iio/common/st_sensors/st_sensors_core.c
index f5a2d445d0c0..dffe00692169 100644
--- a/drivers/iio/common/st_sensors/st_sensors_core.c
+++ b/drivers/iio/common/st_sensors/st_sensors_core.c
@@ -301,6 +301,14 @@ static int st_sensors_set_drdy_int_pin(struct iio_dev *indio_dev,
 		return -EINVAL;
 	}
 
+	if (pdata->open_drain) {
+		if (!sdata->sensor_settings->drdy_irq.addr_od)
+			dev_err(&indio_dev->dev,
+				"open drain requested but unsupported.\n");
+		else
+			sdata->int_pin_open_drain = true;
+	}
+
 	return 0;
 }
 
@@ -321,6 +329,8 @@ static struct st_sensors_platform_data *st_sensors_of_probe(struct device *dev,
 	else
 		pdata->drdy_int_pin = defdata ? defdata->drdy_int_pin : 0;
 
+	pdata->open_drain = of_property_read_bool(np, "drive-open-drain");
+
 	return pdata;
 }
 #else
@@ -374,6 +384,16 @@ int st_sensors_init_sensor(struct iio_dev *indio_dev,
 			return err;
 	}
 
+	if (sdata->int_pin_open_drain) {
+		dev_info(&indio_dev->dev,
+			 "set interrupt line to open drain mode\n");
+		err = st_sensors_write_data_with_mask(indio_dev,
+				sdata->sensor_settings->drdy_irq.addr_od,
+				sdata->sensor_settings->drdy_irq.mask_od, 1);
+		if (err < 0)
+			return err;
+	}
+
 	err = st_sensors_set_axis_enable(indio_dev, ST_SENSORS_ENABLE_ALL_AXIS);
 
 	return err;
diff --git a/drivers/iio/common/st_sensors/st_sensors_trigger.c b/drivers/iio/common/st_sensors/st_sensors_trigger.c
index 6a8c98327945..da72279fcf99 100644
--- a/drivers/iio/common/st_sensors/st_sensors_trigger.c
+++ b/drivers/iio/common/st_sensors/st_sensors_trigger.c
@@ -64,6 +64,19 @@ int st_sensors_allocate_trigger(struct iio_dev *indio_dev,
 			"rising edge\n", irq_trig);
 		irq_trig = IRQF_TRIGGER_RISING;
 	}
+
+	/*
+	 * If the interrupt pin is Open Drain, by definition this
+	 * means that the interrupt line may be shared with other
+	 * peripherals. But to do this we also need to have a status
+	 * register and mask to figure out if this sensor was firing
+	 * the IRQ or not, so we can tell the interrupt handle that
+	 * it was "our" interrupt.
+	 */
+	if (sdata->int_pin_open_drain &&
+	    sdata->sensor_settings->drdy_irq.addr_stat_drdy)
+		irq_trig |= IRQF_SHARED;
+
 	err = request_threaded_irq(irq,
 			iio_trigger_generic_data_rdy_poll,
 			NULL,