Merge tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull TTY changes from Greg Kroah-Hartman:
 "As we skipped the merge window for 3.6-rc1 for the tty tree,
  everything is now settled down and working properly, so we are ready
  for 3.7-rc1.  Here's the patchset, it's big, but the large changes are
  removing a firmware file and adding a staging tty driver (it depended
  on the tty core changes, so it's going through this tree instead of
  the staging tree.)

  All of these patches have been in the linux-next tree for a while.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

Fix up more-or-less trivial conflicts in
 - drivers/char/pcmcia/synclink_cs.c:
    tty NULL dereference fix vs tty_port_cts_enabled() helper function
 - drivers/staging/{Kconfig,Makefile}:
    add-add conflict (dgrp driver added close to other staging drivers)
 - drivers/staging/ipack/devices/ipoctal.c:
    "split ipoctal_channel from iopctal" vs "TTY: use tty_port_register_device"

* tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (235 commits)
  tty/serial: Add kgdb_nmi driver
  tty/serial/amba-pl011: Quiesce interrupts in poll_get_char
  tty/serial/amba-pl011: Implement poll_init callback
  tty/serial/core: Introduce poll_init callback
  kdb: Turn KGDB_KDB=n stubs into static inlines
  kdb: Implement disable_nmi command
  kernel/debug: Mask KGDB NMI upon entry
  serial: pl011: handle corruption at high clock speeds
  serial: sccnxp: Make 'default' choice in switch last
  serial: sccnxp: Remove mask termios caps for SW flow control
  serial: sccnxp: Report actual baudrate back to core
  serial: samsung: Add poll_get_char & poll_put_char
  Powerpc 8xx CPM_UART setting MAXIDL register proportionaly to baud rate
  Powerpc 8xx CPM_UART maxidl should not depend on fifo size
  Powerpc 8xx CPM_UART too many interrupts
  Powerpc 8xx CPM_UART desynchronisation
  serial: set correct baud_base for EXSYS EX-41092 Dual 16950
  serial: omap: fix the reciever line error case
  8250: blacklist Winbond CIR port
  8250_pnp: do pnp probe before legacy probe
  ...

1 files changed, 0 insertions, 21 deletions

diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index a534d8880de1..1d2e3c6f8b59 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -524,33 +524,12 @@ static struct stedma40_chan_cfg uart2_dma_cfg_tx = {
 };
 #endif
 
-#define PRCC_K_SOFTRST_SET      0x18
-#define PRCC_K_SOFTRST_CLEAR    0x1C
-static void ux500_uart0_reset(void)
-{
-	void __iomem *prcc_rst_set, *prcc_rst_clr;
-
-	prcc_rst_set = (void __iomem *)IO_ADDRESS(U8500_CLKRST1_BASE +
-			PRCC_K_SOFTRST_SET);
-	prcc_rst_clr = (void __iomem *)IO_ADDRESS(U8500_CLKRST1_BASE +
-			PRCC_K_SOFTRST_CLEAR);
-
-	/* Activate soft reset PRCC_K_SOFTRST_CLEAR */
-	writel((readl(prcc_rst_clr) | 0x1), prcc_rst_clr);
-	udelay(1);
-
-	/* Release soft reset PRCC_K_SOFTRST_SET */
-	writel((readl(prcc_rst_set) | 0x1), prcc_rst_set);
-	udelay(1);
-}
-
 static struct amba_pl011_data uart0_plat = {
 #ifdef CONFIG_STE_DMA40
 	.dma_filter = stedma40_filter,
 	.dma_rx_param = &uart0_dma_cfg_rx,
 	.dma_tx_param = &uart0_dma_cfg_tx,
 #endif
-	.reset = ux500_uart0_reset,
 };
 
 static struct amba_pl011_data uart1_plat = {