Merge tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Merge "wireless wl12xx and omap device tree changes for v4.1" from Tony
Lindgren:

Wireless and omap changes to make wl12xx driver to use device tree
data instead of platform data from Eliad Peller <eliad@wizery.com>:

- Add device-tree support to the wlcore (wl12xx/wl18xx) driver.

- Update the current users to use the bindings instead of pdata-quirks.

- Finally, remove the deprecated wl12xx_platform_data struct

Note that da850 board file code that still uses the platform data,
but we have da850.dtsi that can be used instead. So it was decided
that we should try to remove the wl12xx support from the da850
board file as suggested by Sekhar Nori <nsekhar@ti.com>. As it's
the last patch in the series, the last patch can be simply reverted
if needed.

As this series touches quite a bit of arch code, it was suggested
by Kalle Valo <kvalo@codeaurora.org> that the whole series should
be merged via the arm-soc tree.

* tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  wlcore: remove wl12xx_platform_data
  ARM: dts: add wl12xx/wl18xx bindings
  wlcore: add device-tree support
  dt: bindings: add TI's wilink wireless device
  wl12xx: use frequency instead of enumerations for pdata clocks
  wlcore: set irq_trigger in board files instead of hiding behind a quirk
  + Linux 4.0-rc4

Signed-off-by: Olof Johansson <olof@lixom.net>

1 files changed, 0 insertions, 112 deletions

diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index 6b5a97da9fe3..1ed545cc2b83 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -38,7 +38,6 @@
 #include <linux/regulator/fixed.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
-#include <linux/wl12xx.h>
 
 #include <mach/common.h>
 #include <mach/cp_intc.h>
@@ -60,9 +59,6 @@
 #define DA850_MMCSD_CD_PIN		GPIO_TO_PIN(4, 0)
 #define DA850_MMCSD_WP_PIN		GPIO_TO_PIN(4, 1)
 
-#define DA850_WLAN_EN			GPIO_TO_PIN(6, 9)
-#define DA850_WLAN_IRQ			GPIO_TO_PIN(6, 10)
-
 #define DA850_MII_MDIO_CLKEN_PIN	GPIO_TO_PIN(2, 6)
 
 static struct mtd_partition da850evm_spiflash_part[] = {
@@ -1343,109 +1339,6 @@ static __init void da850_vpif_init(void)
 static __init void da850_vpif_init(void) {}
 #endif
 
-#ifdef CONFIG_DA850_WL12XX
-
-static void wl12xx_set_power(int index, bool power_on)
-{
-	static bool power_state;
-
-	pr_debug("Powering %s wl12xx", power_on ? "on" : "off");
-
-	if (power_on == power_state)
-		return;
-	power_state = power_on;
-
-	if (power_on) {
-		/* Power up sequence required for wl127x devices */
-		gpio_set_value(DA850_WLAN_EN, 1);
-		usleep_range(15000, 15000);
-		gpio_set_value(DA850_WLAN_EN, 0);
-		usleep_range(1000, 1000);
-		gpio_set_value(DA850_WLAN_EN, 1);
-		msleep(70);
-	} else {
-		gpio_set_value(DA850_WLAN_EN, 0);
-	}
-}
-
-static struct davinci_mmc_config da850_wl12xx_mmc_config = {
-	.set_power	= wl12xx_set_power,
-	.wires		= 4,
-	.max_freq	= 25000000,
-	.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_NONREMOVABLE |
-			  MMC_CAP_POWER_OFF_CARD,
-};
-
-static const short da850_wl12xx_pins[] __initconst = {
-	DA850_MMCSD1_DAT_0, DA850_MMCSD1_DAT_1, DA850_MMCSD1_DAT_2,
-	DA850_MMCSD1_DAT_3, DA850_MMCSD1_CLK, DA850_MMCSD1_CMD,
-	DA850_GPIO6_9, DA850_GPIO6_10,
-	-1
-};
-
-static struct wl12xx_platform_data da850_wl12xx_wlan_data __initdata = {
-	.irq			= -1,
-	.board_ref_clock	= WL12XX_REFCLOCK_38,
-	.platform_quirks	= WL12XX_PLATFORM_QUIRK_EDGE_IRQ,
-};
-
-static __init int da850_wl12xx_init(void)
-{
-	int ret;
-
-	ret = davinci_cfg_reg_list(da850_wl12xx_pins);
-	if (ret) {
-		pr_err("wl12xx/mmc mux setup failed: %d\n", ret);
-		goto exit;
-	}
-
-	ret = da850_register_mmcsd1(&da850_wl12xx_mmc_config);
-	if (ret) {
-		pr_err("wl12xx/mmc registration failed: %d\n", ret);
-		goto exit;
-	}
-
-	ret = gpio_request_one(DA850_WLAN_EN, GPIOF_OUT_INIT_LOW, "wl12xx_en");
-	if (ret) {
-		pr_err("Could not request wl12xx enable gpio: %d\n", ret);
-		goto exit;
-	}
-
-	ret = gpio_request_one(DA850_WLAN_IRQ, GPIOF_IN, "wl12xx_irq");
-	if (ret) {
-		pr_err("Could not request wl12xx irq gpio: %d\n", ret);
-		goto free_wlan_en;
-	}
-
-	da850_wl12xx_wlan_data.irq = gpio_to_irq(DA850_WLAN_IRQ);
-
-	ret = wl12xx_set_platform_data(&da850_wl12xx_wlan_data);
-	if (ret) {
-		pr_err("Could not set wl12xx data: %d\n", ret);
-		goto free_wlan_irq;
-	}
-
-	return 0;
-
-free_wlan_irq:
-	gpio_free(DA850_WLAN_IRQ);
-
-free_wlan_en:
-	gpio_free(DA850_WLAN_EN);
-
-exit:
-	return ret;
-}
-
-#else /* CONFIG_DA850_WL12XX */
-
-static __init int da850_wl12xx_init(void)
-{
-	return 0;
-}
-
-#endif /* CONFIG_DA850_WL12XX */
-
 #define DA850EVM_SATA_REFCLKPN_RATE	(100 * 1000 * 1000)
 
 static __init void da850_evm_init(void)
@@ -1502,11 +1395,6 @@ static __init void da850_evm_init(void)
 		if (ret)
 			pr_warn("%s: MMCSD0 registration failed: %d\n",
 				__func__, ret);
-
-		ret = da850_wl12xx_init();
-		if (ret)
-			pr_warn("%s: WL12xx initialization failed: %d\n",
-				__func__, ret);
 	}
 
 	davinci_serial_init(da8xx_serial_device);