Blackfin arch: Added support for HV Sistemas H8606 board

Signed-off-by: Javier Herrero <jherrero@hvsistemas.es>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

3 files changed, 359 insertions, 2 deletions

diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 7888551ed939..9f9de3e95826 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -295,6 +295,12 @@ config PNAV10
 	help
 	  PNAV 1.0 board Support.
 
+config H8606_HVSISTEMAS
+        bool "HV Sistemas H8606"
+        depends on (BF532)
+        help
+          HV Sistemas H8606 board support.
+
 config GENERIC_BOARD
 	bool "Custom"
 	depends on (BF537 || BF536 \
@@ -317,7 +323,8 @@ config MEM_MT48LC64M4A2FB_7E
 config MEM_MT48LC16M16A2TG_75
 	bool
 	depends on (BFIN533_EZKIT || BFIN561_EZKIT \
-		|| BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM)
+		|| BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM \
+		|| H8606_HVSISTEMAS)
 	default y
 
 config MEM_MT48LC32M8A2_75
@@ -366,7 +373,7 @@ config CLKIN_HZ
 	int "Crystal Frequency in Hz"
 	default "11059200" if BFIN533_STAMP
 	default "27000000" if BFIN533_EZKIT
-	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT)
+	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS)
 	default "30000000" if BFIN561_EZKIT
 	default "24576000" if PNAV10
 	help
@@ -404,6 +411,7 @@ config VCO_MULT
 	default "20" if BFIN537_BLUETECHNIX_CM
 	default "20" if BFIN561_BLUETECHNIX_CM
 	default "20" if BFIN561_EZKIT
+	default "16" if H8606_HVSISTEMAS
 	help
 	  This controls the frequency of the on-chip PLL. This can be between 1 and 64.
 	  PLL Frequency = (Crystal Frequency) * (this setting)
@@ -440,6 +448,7 @@ config SCLK_DIV
 	default 4 if BFIN537_BLUETECHNIX_CM
 	default 4 if BFIN561_BLUETECHNIX_CM
 	default 5 if BFIN561_EZKIT
+	default 3 if H8606_HVSISTEMAS
 	help
 	  This sets the frequency of the system clock (including SDRAM or DDR).
 	  This can be between 1 and 15
@@ -492,11 +501,13 @@ config MEM_SIZE
 	default  64 if BFIN561_EZKIT
 	default 128 if BFIN533_STAMP
 	default  64 if PNAV10
+	default  32 if H8606_HVSISTEMAS
 
 config MEM_ADD_WIDTH
 	int "SDRAM Memory Address Width"
 	default  9 if BFIN533_EZKIT
 	default  9 if BFIN561_EZKIT
+	default  9 if H8606_HVSISTEMAS
 	default 10 if BFIN527_EZKIT
 	default 10 if BFIN537_STAMP
 	default 11 if BFIN533_STAMP
diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c
new file mode 100644
index 000000000000..b941550f9568
--- /dev/null
+++ b/arch/blackfin/mach-bf533/boards/H8606.c
@@ -0,0 +1,345 @@
+/*
+ * File:         arch/blackfin/mach-bf533/H8606.c
+ * Based on:     arch/blackfin/mach-bf533/stamp.c
+ * Author:       Javier Herrero <jherrero@hvsistemas.es>
+ *
+ * Created:      2007
+ * Description:  Board Info File for the HV Sistemas H8606 board
+ *
+ * Modified:
+ *               Copyright 2005 National ICT Australia (NICTA)
+ *               Copyright 2004-2006 Analog Devices Inc
+ *		 Copyright 2007 HV Sistemas S.L.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#include <linux/usb_isp1362.h>
+#endif
+#include <linux/pata_platform.h>
+#include <linux/irq.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "HV Sistemas H8606";
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_BFIN_MODULE)
+static struct platform_device rtc_device = {
+	.name = "rtc-bfin",
+	.id   = -1,
+};
+#endif
+
+/*
+*  Driver needs to know address, irq and flag pin.
+ */
+ #if	defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+static struct resource dm9000_resources[] = {
+	[0] = {
+		.start	= 0x20300000,
+		.end	= 0x20300000 + 8,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_PF10,
+		.end	= IRQ_PF10,
+		.flags	= (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
+	},
+};
+
+static struct platform_device dm9000_device = {
+    .id			= 0,
+    .name		= "dm9000",
+    .resource		= dm9000_resources,
+    .num_resources	= ARRAY_SIZE(dm9000_resources),
+};
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+static struct resource smc91x_resources[] = {
+	{
+		.name = "smc91x-regs",
+		.start = 0x20300300,
+		.end = 0x20300300 + 16,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PROG_INTB,
+		.end = IRQ_PROG_INTB,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	}, {
+		/*
+		 *  denotes the flag pin and is used directly if
+		 *  CONFIG_IRQCHIP_DEMUX_GPIO is defined.
+		 */
+		.start = IRQ_PF7,
+		.end = IRQ_PF7,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct platform_device smc91x_device = {
+	.name = "smc91x",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(smc91x_resources),
+	.resource = smc91x_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+	{
+		.start = 0x20300000,
+		.end = 0x20300000 + 0x100,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF10,
+		.end = IRQ_PF10,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct platform_device net2272_bfin_device = {
+	.name = "net2272",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(net2272_bfin_resources),
+	.resource = net2272_bfin_resources,
+};
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+	{
+		.name = "bootloader",
+		.size = 0x00060000,
+		.offset = 0,
+		.mask_flags = MTD_CAP_ROM
+	}, {
+		.name = "kernel",
+		.size = 0x100000,
+		.offset = 0x60000
+	}, {
+		.name = "file system",
+		.size = 0x6a0000,
+		.offset = 0x00160000,
+	}
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+	.name = "m25p80",
+	.parts = bfin_spi_flash_partitions,
+	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+	.type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+	.ctl_reg = 0x1000,
+	.enable_dma = 1,         /* use dma transfer with this chip*/
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+	.ctl_reg = 0x1000,
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_PBX)
+static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
+	.ctl_reg	= 0x1c04,
+	.enable_dma	= 0,
+	.bits_per_word	= 8,
+	.cs_change_per_word = 1,
+};
+#endif
+
+/* Notice: for blackfin, the speed_hz is the value of register
+ * SPI_BAUD, not the real baudrate */
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+	{
+		/* the modalias must be the same as spi device driver name */
+		.modalias = "m25p80", /* Name of spi_driver for this device */
+		/* this value is the baudrate divisor */
+		.max_speed_hz = 50000000, /* actual baudrate is SCLK/(2xspeed_hz) */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 2, /* Framework chip select. On STAMP537 it is SPISSEL2*/
+		.platform_data = &bfin_spi_flash_data,
+		.controller_data = &spi_flash_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE)
+	{
+		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+		.max_speed_hz = 4,     /* actual baudrate is SCLK/(2xspeed_hz) */
+		.bus_num = 1, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.controller_data = &spi_adc_chip_info,
+	},
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+	{
+		.modalias = "ad1836-spi",
+		.max_speed_hz = 16,
+		.bus_num = 1,
+		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.controller_data = &ad1836_spi_chip_info,
+	},
+#endif
+
+#if defined(CONFIG_PBX)
+	{
+		.modalias	 = "fxs-spi",
+		.max_speed_hz	 = 4,
+		.bus_num	 = 1,
+		.chip_select	 = 3,
+		.controller_data = &spi_si3xxx_chip_info,
+	},
+
+	{
+		.modalias	 = "fxo-spi",
+		.max_speed_hz	 = 4,
+		.bus_num	 = 1,
+		.chip_select	 = 2,
+		.controller_data = &spi_si3xxx_chip_info,
+	},
+#endif
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+	[0] = {
+		.start = SPI0_REGBASE,
+		.end   = SPI0_REGBASE + 0xFF,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = CH_SPI,
+		.end   = CH_SPI,
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+	.num_chipselect = 8,
+	.enable_dma = 1,  /* master has the ability to do dma transfer */
+};
+
+static struct platform_device bfin_spi0_device = {
+	.name = "bfin-spi",
+	.id = 0, /* Bus number */
+	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
+	.resource = bfin_spi0_resource,
+	.dev = {
+		.platform_data = &bfin_spi0_info, /* Passed to driver */
+	},
+};
+#endif  /* spi master and devices */
+
+#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+static struct platform_device bfin_fb_device = {
+	.name = "bf537-fb",
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device bfin_uart_device = {
+	.name = "bfin-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_uart_resources),
+	.resource = bfin_uart_resources,
+};
+#endif
+
+static struct platform_device *stamp_devices[] __initdata = {
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+	&rtc_device,
+#endif
+
+#if	defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+	&dm9000_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+	&smc91x_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	&net2272_bfin_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	&bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+	&bfin_uart_device,
+#endif
+};
+
+static int __init H8606_init(void)
+{
+	printk(KERN_INFO "HV Sistemas H8606 board support by http://www.hvsistemas.com\n");
+	printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+	platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+#endif
+	return 0;
+}
+
+arch_initcall(H8606_init);
\ No newline at end of file
diff --git a/arch/blackfin/mach-bf533/boards/Makefile b/arch/blackfin/mach-bf533/boards/Makefile
index 12a631ab389d..2452b456ccbd 100644
--- a/arch/blackfin/mach-bf533/boards/Makefile
+++ b/arch/blackfin/mach-bf533/boards/Makefile
@@ -6,3 +6,4 @@ obj-$(CONFIG_GENERIC_BOARD)            += generic_board.o
 obj-$(CONFIG_BFIN533_STAMP)            += stamp.o
 obj-$(CONFIG_BFIN533_EZKIT)            += ezkit.o
 obj-$(CONFIG_BFIN533_BLUETECHNIX_CM)   += cm_bf533.o
+obj-$(CONFIG_H8606_HVSISTEMAS)         += H8606.o