Merge branch 'for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata changes from Tejun Heo:
 "Except for a few, all the changes are for ahci platform drivers for
  the arm devices.  Nothing too interesting or dangerous.  There's one
  merge from libata/for-3.16-fixes to pull in dependent changes"

* 'for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (23 commits)
  ata: libahci: Silence compiler warning on 64-bit
  Documentation: bindings: document the sub-nodes AHCI bindings
  ata: ahci_platform: add a generic AHCI compatible
  ata: libahci: allow to use multiple PHYs
  ata: libahci_platform: move port_map parameters into the AHCI structure
  ahci: imx: add missing clk_disable_unprepare() on error in imx_sata_enable()
  ahci_xgene: Use correct OOB tunning parameters for APM X-Gene SoC AHCI SATA Host controller driver.
  ahci_xgene: Fix the watermark threshold for the APM X-Gene SATA host controller driver.
  ahci: st: Make of_device_id array const
  sata_sil24: Identify which card suffered IRQ status error
  ahci: st: Provide DT bindings for ST's SATA implementation
  ata: Add support for the Tegra124 SATA controller
  ata: ahci_platform: Increase AHCI_MAX_CLKS to 4
  of: Add NVIDIA Tegra SATA controller binding
  dt-bindings: ata: document ability to disable spread-spectrum clock
  ata: ahci_imx: add disable for spread-spectrum
  dt-bindings: ata: add ahci_imx electrical properties
  ata: ahci_imx: allow hardware parameters to be specified in DT
  dt-bindings: ata: create bindings for imx sata controller
  ata: pata_samsung_cf: removes s5pc100 related ata codes
  ...

25 files changed, 917 insertions, 141 deletions

diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt
index c96d8dcf98fd..4ab09f2202d4 100644
--- a/Documentation/devicetree/bindings/ata/ahci-platform.txt
+++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt
@@ -3,28 +3,43 @@
 SATA nodes are defined to describe on-chip Serial ATA controllers.
 Each SATA controller should have its own node.
 
+It is possible, but not required, to represent each port as a sub-node.
+It allows to enable each port independently when dealing with multiple
+PHYs.
+
 Required properties:
 - compatible        : compatible string, one of:
   - "allwinner,sun4i-a10-ahci"
-  - "fsl,imx53-ahci"
-  - "fsl,imx6q-ahci"
   - "hisilicon,hisi-ahci"
   - "ibm,476gtr-ahci"
   - "marvell,armada-380-ahci"
   - "snps,dwc-ahci"
   - "snps,exynos5440-ahci"
   - "snps,spear-ahci"
+  - "generic-ahci"
 - interrupts        : <interrupt mapping for SATA IRQ>
 - reg               : <registers mapping>
 
+Please note that when using "generic-ahci" you must also specify a SoC specific
+compatible:
+	compatible = "manufacturer,soc-model-ahci", "generic-ahci";
+
 Optional properties:
 - dma-coherent      : Present if dma operations are coherent
 - clocks            : a list of phandle + clock specifier pairs
 - target-supply     : regulator for SATA target power
+- phys              : reference to the SATA PHY node
+- phy-names         : must be "sata-phy"
+
+Required properties when using sub-nodes:
+- #address-cells    : number of cells to encode an address
+- #size-cells       : number of cells representing the size of an address
+
+
+Sub-nodes required properties:
+- reg               : the port number
+- phys              : reference to the SATA PHY node
 
-"fsl,imx53-ahci", "fsl,imx6q-ahci" required properties:
-- clocks            : must contain the sata, sata_ref and ahb clocks
-- clock-names       : must contain "ahb" for the ahb clock
 
 Examples:
         sata@ffe08000 {
@@ -40,3 +55,23 @@ Examples:
 		clocks = <&pll6 0>, <&ahb_gates 25>;
 		target-supply = <&reg_ahci_5v>;
 	};
+
+With sub-nodes:
+	sata@f7e90000 {
+		compatible = "marvell,berlin2q-achi", "generic-ahci";
+		reg = <0xe90000 0x1000>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&chip CLKID_SATA>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sata0: sata-port@0 {
+			reg = <0>;
+			phys = <&sata_phy 0>;
+		};
+
+		sata1: sata-port@1 {
+			reg = <1>;
+			phys = <&sata_phy 1>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/ata/ahci-st.txt b/Documentation/devicetree/bindings/ata/ahci-st.txt
new file mode 100644
index 000000000000..0574a77a0b9f
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/ahci-st.txt
@@ -0,0 +1,31 @@
+STMicroelectronics STi SATA controller
+
+This binding describes a SATA device.
+
+Required properties:
+ - compatible	   : Must be "st,sti-ahci"
+ - reg		   : Physical base addresses and length of register sets
+ - interrupts	   : Interrupt associated with the SATA device
+ - interrupt-names :   Associated name must be; "hostc"
+ - resets	   : The power-down and soft-reset lines of SATA IP
+ - reset-names	   :   Associated names must be; "pwr-dwn" and "sw-rst"
+ - clocks	   : The phandle for the clock
+ - clock-names	   :   Associated name must be; "ahci_clk"
+ - phys		   : The phandle for the PHY device
+ - phy-names	   :   Associated name must be; "ahci_phy"
+
+Example:
+
+	sata0: sata@fe380000 {
+		compatible      = "st,sti-ahci";
+		reg             = <0xfe380000 0x1000>;
+		interrupts      = <GIC_SPI 157 IRQ_TYPE_NONE>;
+		interrupt-names = "hostc";
+		phys	        = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>;
+		phy-names       = "ahci_phy";
+		resets	        = <&powerdown STIH416_SATA0_POWERDOWN>,
+				  <&softreset STIH416_SATA0_SOFTRESET>;
+		reset-names     = "pwr-dwn", "sw-rst";
+		clocks	        = <&clk_s_a0_ls CLK_ICN_REG>;
+		clock-names     = "ahci_clk";
+	};
diff --git a/Documentation/devicetree/bindings/ata/imx-sata.txt b/Documentation/devicetree/bindings/ata/imx-sata.txt
new file mode 100644
index 000000000000..fa511db18408
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/imx-sata.txt
@@ -0,0 +1,36 @@
+* Freescale i.MX AHCI SATA Controller
+
+The Freescale i.MX SATA controller mostly conforms to the AHCI interface
+with some special extensions at integration level.
+
+Required properties:
+- compatible : should be one of the following:
+   - "fsl,imx53-ahci" for i.MX53 SATA controller
+   - "fsl,imx6q-ahci" for i.MX6Q SATA controller
+- interrupts : interrupt mapping for SATA IRQ
+- reg : registers mapping
+- clocks : list of clock specifiers, must contain an entry for each
+  required entry in clock-names
+- clock-names : should include "sata", "sata_ref" and "ahb" entries
+
+Optional properties:
+- fsl,transmit-level-mV : transmit voltage level, in millivolts.
+- fsl,transmit-boost-mdB : transmit boost level, in milli-decibels
+- fsl,transmit-atten-16ths : transmit attenuation, in 16ths
+- fsl,receive-eq-mdB : receive equalisation, in milli-decibels
+  Please refer to the technical documentation or the driver source code
+  for the list of legal values for these options.
+- fsl,no-spread-spectrum : disable spread-spectrum clocking on the SATA
+  link.
+
+Examples:
+
+sata@02200000 {
+	compatible = "fsl,imx6q-ahci";
+	reg = <0x02200000 0x4000>;
+	interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&clks IMX6QDL_CLK_SATA>,
+		 <&clks IMX6QDL_CLK_SATA_REF_100M>,
+		 <&clks IMX6QDL_CLK_AHB>;
+	clock-names = "sata", "sata_ref", "ahb";
+};
diff --git a/Documentation/devicetree/bindings/ata/tegra-sata.txt b/Documentation/devicetree/bindings/ata/tegra-sata.txt
new file mode 100644
index 000000000000..946f2072570b
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/tegra-sata.txt
@@ -0,0 +1,30 @@
+Tegra124 SoC SATA AHCI controller
+
+Required properties :
+- compatible : "nvidia,tegra124-ahci".
+- reg : Should contain 2 entries:
+  - AHCI register set (SATA BAR5)
+  - SATA register set
+- interrupts : Defines the interrupt used by SATA
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  - sata
+  - sata-oob
+  - cml1
+  - pll_e
+- resets : Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names : Must include the following entries:
+  - sata
+  - sata-oob
+  - sata-cold
+- phys : Must contain an entry for each entry in phy-names.
+  See ../phy/phy-bindings.txt for details.
+- phy-names : Must include the following entries:
+  - sata-phy : XUSB PADCTL SATA PHY
+- hvdd-supply : Defines the SATA HVDD regulator
+- vddio-supply : Defines the SATA VDDIO regulator
+- avdd-supply : Defines the SATA AVDD regulator
+- target-5v-supply : Defines the SATA 5V power regulator
+- target-12v-supply : Defines the SATA 12V power regulator
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 7671dbac6015..e65d400efd44 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -141,6 +141,15 @@ config AHCI_SUNXI
 
 	  If unsure, say N.
 
+config AHCI_TEGRA
+	tristate "NVIDIA Tegra124 AHCI SATA support"
+	depends on ARCH_TEGRA
+	help
+	  This option enables support for the NVIDIA Tegra124 SoC's
+	  onboard AHCI SATA.
+
+	  If unsure, say N.
+
 config AHCI_XGENE
 	tristate "APM X-Gene 6.0Gbps AHCI SATA host controller support"
 	depends on PHY_XGENE
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 5a02aeecef5b..ae41107afc1f 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_MVEBU)	+= ahci_mvebu.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_ST)		+= ahci_st.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_TEGRA)	+= ahci_tegra.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_XGENE)	+= ahci_xgene.o libahci.o libahci_platform.o
 
 # SFF w/ custom DMA
diff --git a/drivers/ata/acard-ahci.c b/drivers/ata/acard-ahci.c
index 0cd7c7a39e5b..25d0ac32e721 100644
--- a/drivers/ata/acard-ahci.c
+++ b/drivers/ata/acard-ahci.c
@@ -441,7 +441,7 @@ static int acard_ahci_init_one(struct pci_dev *pdev, const struct pci_device_id
 	hpriv->mmio = pcim_iomap_table(pdev)[AHCI_PCI_BAR];
 
 	/* save initial config */
-	ahci_save_initial_config(&pdev->dev, hpriv, 0, 0);
+	ahci_save_initial_config(&pdev->dev, hpriv);
 
 	/* prepare host */
 	if (hpriv->cap & HOST_CAP_NCQ)
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 4cd52a4541a9..a29f8012fb08 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -526,8 +526,7 @@ static void ahci_pci_save_initial_config(struct pci_dev *pdev,
 			  "Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.\n");
 	}
 
-	ahci_save_initial_config(&pdev->dev, hpriv, force_port_map,
-				 mask_port_map);
+	ahci_save_initial_config(&pdev->dev, hpriv);
 }
 
 static int ahci_pci_reset_controller(struct ata_host *host)
diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
index 5513296e5e2e..59ae0ee00149 100644
--- a/drivers/ata/ahci.h
+++ b/drivers/ata/ahci.h
@@ -53,7 +53,7 @@
 
 enum {
 	AHCI_MAX_PORTS		= 32,
-	AHCI_MAX_CLKS		= 3,
+	AHCI_MAX_CLKS		= 4,
 	AHCI_MAX_SG		= 168, /* hardware max is 64K */
 	AHCI_DMA_BOUNDARY	= 0xffffffff,
 	AHCI_MAX_CMDS		= 32,
@@ -316,8 +316,12 @@ struct ahci_port_priv {
 };
 
 struct ahci_host_priv {
-	void __iomem *		mmio;		/* bus-independent mem map */
+	/* Input fields */
 	unsigned int		flags;		/* AHCI_HFLAG_* */
+	u32			force_port_map;	/* force port map */
+	u32			mask_port_map;	/* mask out particular bits */
+
+	void __iomem *		mmio;		/* bus-independent mem map */
 	u32			cap;		/* cap to use */
 	u32			cap2;		/* cap2 to use */
 	u32			port_map;	/* port map to use */
@@ -330,7 +334,12 @@ struct ahci_host_priv {
 	bool			got_runtime_pm; /* Did we do pm_runtime_get? */
 	struct clk		*clks[AHCI_MAX_CLKS]; /* Optional */
 	struct regulator	*target_pwr;	/* Optional */
-	struct phy		*phy;		/* If platform uses phy */
+	/*
+	 * If platform uses PHYs. There is a 1:1 relation between the port number and
+	 * the PHY position in this array.
+	 */
+	struct phy		**phys;
+	unsigned		nports;		/* Number of ports */
 	void			*plat_data;	/* Other platform data */
 	/*
 	 * Optional ahci_start_engine override, if not set this gets set to the
@@ -361,9 +370,7 @@ unsigned int ahci_dev_classify(struct ata_port *ap);
 void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
 			u32 opts);
 void ahci_save_initial_config(struct device *dev,
-			      struct ahci_host_priv *hpriv,
-			      unsigned int force_port_map,
-			      unsigned int mask_port_map);
+			      struct ahci_host_priv *hpriv);
 void ahci_init_controller(struct ata_host *host);
 int ahci_reset_controller(struct ata_host *host);
 
diff --git a/drivers/ata/ahci_da850.c b/drivers/ata/ahci_da850.c
index 2b77d53bccf8..ad1e71ec10cf 100644
--- a/drivers/ata/ahci_da850.c
+++ b/drivers/ata/ahci_da850.c
@@ -85,8 +85,7 @@ static int ahci_da850_probe(struct platform_device *pdev)
 
 	da850_sata_init(dev, pwrdn_reg, hpriv->mmio);
 
-	rc = ahci_platform_init_host(pdev, hpriv, &ahci_da850_port_info,
-				     0, 0, 0);
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_da850_port_info);
 	if (rc)
 		goto disable_resources;
 
diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c
index cac4360f272a..f3970b4ed889 100644
--- a/drivers/ata/ahci_imx.c
+++ b/drivers/ata/ahci_imx.c
@@ -64,6 +64,7 @@ struct imx_ahci_priv {
 	struct regmap *gpr;
 	bool no_device;
 	bool first_time;
+	u32 phy_params;
 };
 
 static int ahci_imx_hotplug;
@@ -248,14 +249,7 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv)
 				   IMX6Q_GPR13_SATA_TX_LVL_MASK |
 				   IMX6Q_GPR13_SATA_MPLL_CLK_EN |
 				   IMX6Q_GPR13_SATA_TX_EDGE_RATE,
-				   IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB |
-				   IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M |
-				   IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F |
-				   IMX6Q_GPR13_SATA_SPD_MODE_3P0G |
-				   IMX6Q_GPR13_SATA_MPLL_SS_EN |
-				   IMX6Q_GPR13_SATA_TX_ATTEN_9_16 |
-				   IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB |
-				   IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
+				   imxpriv->phy_params);
 		regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
 				   IMX6Q_GPR13_SATA_MPLL_CLK_EN,
 				   IMX6Q_GPR13_SATA_MPLL_CLK_EN);
@@ -265,7 +259,7 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv)
 		ret = imx_sata_phy_reset(hpriv);
 		if (ret) {
 			dev_err(dev, "failed to reset phy: %d\n", ret);
-			goto disable_regulator;
+			goto disable_clk;
 		}
 	}
 
@@ -273,6 +267,8 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv)
 
 	return 0;
 
+disable_clk:
+	clk_disable_unprepare(imxpriv->sata_ref_clk);
 disable_regulator:
 	if (hpriv->target_pwr)
 		regulator_disable(hpriv->target_pwr);
@@ -369,6 +365,165 @@ static const struct of_device_id imx_ahci_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, imx_ahci_of_match);
 
+struct reg_value {
+	u32 of_value;
+	u32 reg_value;
+};
+
+struct reg_property {
+	const char *name;
+	const struct reg_value *values;
+	size_t num_values;
+	u32 def_value;
+	u32 set_value;
+};
+
+static const struct reg_value gpr13_tx_level[] = {
+	{  937, IMX6Q_GPR13_SATA_TX_LVL_0_937_V },
+	{  947, IMX6Q_GPR13_SATA_TX_LVL_0_947_V },
+	{  957, IMX6Q_GPR13_SATA_TX_LVL_0_957_V },
+	{  966, IMX6Q_GPR13_SATA_TX_LVL_0_966_V },
+	{  976, IMX6Q_GPR13_SATA_TX_LVL_0_976_V },
+	{  986, IMX6Q_GPR13_SATA_TX_LVL_0_986_V },
+	{  996, IMX6Q_GPR13_SATA_TX_LVL_0_996_V },
+	{ 1005, IMX6Q_GPR13_SATA_TX_LVL_1_005_V },
+	{ 1015, IMX6Q_GPR13_SATA_TX_LVL_1_015_V },
+	{ 1025, IMX6Q_GPR13_SATA_TX_LVL_1_025_V },
+	{ 1035, IMX6Q_GPR13_SATA_TX_LVL_1_035_V },
+	{ 1045, IMX6Q_GPR13_SATA_TX_LVL_1_045_V },
+	{ 1054, IMX6Q_GPR13_SATA_TX_LVL_1_054_V },
+	{ 1064, IMX6Q_GPR13_SATA_TX_LVL_1_064_V },
+	{ 1074, IMX6Q_GPR13_SATA_TX_LVL_1_074_V },
+	{ 1084, IMX6Q_GPR13_SATA_TX_LVL_1_084_V },
+	{ 1094, IMX6Q_GPR13_SATA_TX_LVL_1_094_V },
+	{ 1104, IMX6Q_GPR13_SATA_TX_LVL_1_104_V },
+	{ 1113, IMX6Q_GPR13_SATA_TX_LVL_1_113_V },
+	{ 1123, IMX6Q_GPR13_SATA_TX_LVL_1_123_V },
+	{ 1133, IMX6Q_GPR13_SATA_TX_LVL_1_133_V },
+	{ 1143, IMX6Q_GPR13_SATA_TX_LVL_1_143_V },
+	{ 1152, IMX6Q_GPR13_SATA_TX_LVL_1_152_V },
+	{ 1162, IMX6Q_GPR13_SATA_TX_LVL_1_162_V },
+	{ 1172, IMX6Q_GPR13_SATA_TX_LVL_1_172_V },
+	{ 1182, IMX6Q_GPR13_SATA_TX_LVL_1_182_V },
+	{ 1191, IMX6Q_GPR13_SATA_TX_LVL_1_191_V },
+	{ 1201, IMX6Q_GPR13_SATA_TX_LVL_1_201_V },
+	{ 1211, IMX6Q_GPR13_SATA_TX_LVL_1_211_V },
+	{ 1221, IMX6Q_GPR13_SATA_TX_LVL_1_221_V },
+	{ 1230, IMX6Q_GPR13_SATA_TX_LVL_1_230_V },
+	{ 1240, IMX6Q_GPR13_SATA_TX_LVL_1_240_V }
+};
+
+static const struct reg_value gpr13_tx_boost[] = {
+	{    0, IMX6Q_GPR13_SATA_TX_BOOST_0_00_DB },
+	{  370, IMX6Q_GPR13_SATA_TX_BOOST_0_37_DB },
+	{  740, IMX6Q_GPR13_SATA_TX_BOOST_0_74_DB },
+	{ 1110, IMX6Q_GPR13_SATA_TX_BOOST_1_11_DB },
+	{ 1480, IMX6Q_GPR13_SATA_TX_BOOST_1_48_DB },
+	{ 1850, IMX6Q_GPR13_SATA_TX_BOOST_1_85_DB },
+	{ 2220, IMX6Q_GPR13_SATA_TX_BOOST_2_22_DB },
+	{ 2590, IMX6Q_GPR13_SATA_TX_BOOST_2_59_DB },
+	{ 2960, IMX6Q_GPR13_SATA_TX_BOOST_2_96_DB },
+	{ 3330, IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB },
+	{ 3700, IMX6Q_GPR13_SATA_TX_BOOST_3_70_DB },
+	{ 4070, IMX6Q_GPR13_SATA_TX_BOOST_4_07_DB },
+	{ 4440, IMX6Q_GPR13_SATA_TX_BOOST_4_44_DB },
+	{ 4810, IMX6Q_GPR13_SATA_TX_BOOST_4_81_DB },
+	{ 5280, IMX6Q_GPR13_SATA_TX_BOOST_5_28_DB },
+	{ 5750, IMX6Q_GPR13_SATA_TX_BOOST_5_75_DB }
+};
+
+static const struct reg_value gpr13_tx_atten[] = {
+	{  8, IMX6Q_GPR13_SATA_TX_ATTEN_8_16 },
+	{  9, IMX6Q_GPR13_SATA_TX_ATTEN_9_16 },
+	{ 10, IMX6Q_GPR13_SATA_TX_ATTEN_10_16 },
+	{ 12, IMX6Q_GPR13_SATA_TX_ATTEN_12_16 },
+	{ 14, IMX6Q_GPR13_SATA_TX_ATTEN_14_16 },
+	{ 16, IMX6Q_GPR13_SATA_TX_ATTEN_16_16 },
+};
+
+static const struct reg_value gpr13_rx_eq[] = {
+	{  500, IMX6Q_GPR13_SATA_RX_EQ_VAL_0_5_DB },
+	{ 1000, IMX6Q_GPR13_SATA_RX_EQ_VAL_1_0_DB },
+	{ 1500, IMX6Q_GPR13_SATA_RX_EQ_VAL_1_5_DB },
+	{ 2000, IMX6Q_GPR13_SATA_RX_EQ_VAL_2_0_DB },
+	{ 2500, IMX6Q_GPR13_SATA_RX_EQ_VAL_2_5_DB },
+	{ 3000, IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB },
+	{ 3500, IMX6Q_GPR13_SATA_RX_EQ_VAL_3_5_DB },
+	{ 4000, IMX6Q_GPR13_SATA_RX_EQ_VAL_4_0_DB },
+};
+
+static const struct reg_property gpr13_props[] = {
+	{
+		.name = "fsl,transmit-level-mV",
+		.values = gpr13_tx_level,
+		.num_values = ARRAY_SIZE(gpr13_tx_level),
+		.def_value = IMX6Q_GPR13_SATA_TX_LVL_1_025_V,
+	}, {
+		.name = "fsl,transmit-boost-mdB",
+		.values = gpr13_tx_boost,
+		.num_values = ARRAY_SIZE(gpr13_tx_boost),
+		.def_value = IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB,
+	}, {
+		.name = "fsl,transmit-atten-16ths",
+		.values = gpr13_tx_atten,
+		.num_values = ARRAY_SIZE(gpr13_tx_atten),
+		.def_value = IMX6Q_GPR13_SATA_TX_ATTEN_9_16,
+	}, {
+		.name = "fsl,receive-eq-mdB",
+		.values = gpr13_rx_eq,
+		.num_values = ARRAY_SIZE(gpr13_rx_eq),
+		.def_value = IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB,
+	}, {
+		.name = "fsl,no-spread-spectrum",
+		.def_value = IMX6Q_GPR13_SATA_MPLL_SS_EN,
+		.set_value = 0,
+	},
+};
+
+static u32 imx_ahci_parse_props(struct device *dev,
+				const struct reg_property *prop, size_t num)
+{
+	struct device_node *np = dev->of_node;
+	u32 reg_value = 0;
+	int i, j;
+
+	for (i = 0; i < num; i++, prop++) {
+		u32 of_val;
+
+		if (prop->num_values == 0) {
+			if (of_property_read_bool(np, prop->name))
+				reg_value |= prop->set_value;
+			else
+				reg_value |= prop->def_value;
+			continue;
+		}
+
+		if (of_property_read_u32(np, prop->name, &of_val)) {
+			dev_info(dev, "%s not specified, using %08x\n",
+				prop->name, prop->def_value);
+			reg_value |= prop->def_value;
+			continue;
+		}
+
+		for (j = 0; j < prop->num_values; j++) {
+			if (prop->values[j].of_value == of_val) {
+				dev_info(dev, "%s value %u, using %08x\n",
+					prop->name, of_val, prop->values[j].reg_value);
+				reg_value |= prop->values[j].reg_value;
+				break;
+			}
+		}
+
+		if (j == prop->num_values) {
+			dev_err(dev, "DT property %s is not a valid value\n",
+				prop->name);
+			reg_value |= prop->def_value;
+		}
+	}
+
+	return reg_value;
+}
+
 static int imx_ahci_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -410,6 +565,8 @@ static int imx_ahci_probe(struct platform_device *pdev)
 	}
 
 	if (imxpriv->type == AHCI_IMX6Q) {
+		u32 reg_value;
+
 		imxpriv->gpr = syscon_regmap_lookup_by_compatible(
 							"fsl,imx6q-iomuxc-gpr");
 		if (IS_ERR(imxpriv->gpr)) {
@@ -417,6 +574,15 @@ static int imx_ahci_probe(struct platform_device *pdev)
 				"failed to find fsl,imx6q-iomux-gpr regmap\n");
 			return PTR_ERR(imxpriv->gpr);
 		}
+
+		reg_value = imx_ahci_parse_props(dev, gpr13_props,
+						 ARRAY_SIZE(gpr13_props));
+
+		imxpriv->phy_params =
+				   IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M |
+				   IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F |
+				   IMX6Q_GPR13_SATA_SPD_MODE_3P0G |
+				   reg_value;
 	}
 
 	hpriv = ahci_platform_get_resources(pdev);
@@ -454,8 +620,7 @@ static int imx_ahci_probe(struct platform_device *pdev)
 	reg_val = clk_get_rate(imxpriv->ahb_clk) / 1000;
 	writel(reg_val, hpriv->mmio + IMX_TIMER1MS);
 
-	ret = ahci_platform_init_host(pdev, hpriv, &ahci_imx_port_info,
-				      0, 0, 0);
+	ret = ahci_platform_init_host(pdev, hpriv, &ahci_imx_port_info);
 	if (ret)
 		goto disable_sata;
 
diff --git a/drivers/ata/ahci_mvebu.c b/drivers/ata/ahci_mvebu.c
index fd3dfd733b84..68672d2692ee 100644
--- a/drivers/ata/ahci_mvebu.c
+++ b/drivers/ata/ahci_mvebu.c
@@ -88,8 +88,7 @@ static int ahci_mvebu_probe(struct platform_device *pdev)
 	ahci_mvebu_mbus_config(hpriv, dram);
 	ahci_mvebu_regret_option(hpriv);
 
-	rc = ahci_platform_init_host(pdev, hpriv, &ahci_mvebu_port_info,
-				     0, 0, 0);
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_mvebu_port_info);
 	if (rc)
 		goto disable_resources;
 
diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
index b10d81ddb528..f61ddb9146d6 100644
--- a/drivers/ata/ahci_platform.c
+++ b/drivers/ata/ahci_platform.c
@@ -34,7 +34,6 @@ static int ahci_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct ahci_platform_data *pdata = dev_get_platdata(dev);
 	struct ahci_host_priv *hpriv;
-	unsigned long hflags = 0;
 	int rc;
 
 	hpriv = ahci_platform_get_resources(pdev);
@@ -58,10 +57,9 @@ static int ahci_probe(struct platform_device *pdev)
 	}
 
 	if (of_device_is_compatible(dev->of_node, "hisilicon,hisi-ahci"))
-		hflags |= AHCI_HFLAG_NO_FBS | AHCI_HFLAG_NO_NCQ;
+		hpriv->flags |= AHCI_HFLAG_NO_FBS | AHCI_HFLAG_NO_NCQ;
 
-	rc = ahci_platform_init_host(pdev, hpriv, &ahci_port_info,
-				     hflags, 0, 0);
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_port_info);
 	if (rc)
 		goto pdata_exit;
 
@@ -78,6 +76,8 @@ static SIMPLE_DEV_PM_OPS(ahci_pm_ops, ahci_platform_suspend,
 			 ahci_platform_resume);
 
 static const struct of_device_id ahci_of_match[] = {
+	{ .compatible = "generic-ahci", },
+	/* Keep the following compatibles for device tree compatibility */
 	{ .compatible = "snps,spear-ahci", },
 	{ .compatible = "snps,exynos5440-ahci", },
 	{ .compatible = "ibm,476gtr-ahci", },
diff --git a/drivers/ata/ahci_st.c b/drivers/ata/ahci_st.c
index 2595598df9ce..835d6eea84fd 100644
--- a/drivers/ata/ahci_st.c
+++ b/drivers/ata/ahci_st.c
@@ -166,7 +166,7 @@ static int st_ahci_probe(struct platform_device *pdev)
 	if (err)
 		return err;
 
-	err = ahci_platform_init_host(pdev, hpriv, &st_ahci_port_info, 0, 0, 0);
+	err = ahci_platform_init_host(pdev, hpriv, &st_ahci_port_info);
 	if (err) {
 		ahci_platform_disable_resources(hpriv);
 		return err;
@@ -221,7 +221,7 @@ static int st_ahci_resume(struct device *dev)
 
 static SIMPLE_DEV_PM_OPS(st_ahci_pm_ops, st_ahci_suspend, st_ahci_resume);
 
-static struct of_device_id st_ahci_match[] = {
+static const struct of_device_id st_ahci_match[] = {
 	{ .compatible = "st,ahci", },
 	{},
 };
diff --git a/drivers/ata/ahci_sunxi.c b/drivers/ata/ahci_sunxi.c
index 02002f125bd4..e44d675a30ec 100644
--- a/drivers/ata/ahci_sunxi.c
+++ b/drivers/ata/ahci_sunxi.c
@@ -167,7 +167,6 @@ static int ahci_sunxi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct ahci_host_priv *hpriv;
-	unsigned long hflags;
 	int rc;
 
 	hpriv = ahci_platform_get_resources(pdev);
@@ -184,11 +183,10 @@ static int ahci_sunxi_probe(struct platform_device *pdev)
 	if (rc)
 		goto disable_resources;
 
-	hflags = AHCI_HFLAG_32BIT_ONLY | AHCI_HFLAG_NO_MSI |
-		 AHCI_HFLAG_NO_PMP | AHCI_HFLAG_YES_NCQ;
+	hpriv->flags = AHCI_HFLAG_32BIT_ONLY | AHCI_HFLAG_NO_MSI |
+		       AHCI_HFLAG_NO_PMP | AHCI_HFLAG_YES_NCQ;
 
-	rc = ahci_platform_init_host(pdev, hpriv, &ahci_sunxi_port_info,
-				     hflags, 0, 0);
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_sunxi_port_info);
 	if (rc)
 		goto disable_resources;
 
diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c
new file mode 100644
index 000000000000..fc3df47fca35
--- /dev/null
+++ b/drivers/ata/ahci_tegra.c
@@ -0,0 +1,376 @@
+/*
+ * drivers/ata/ahci_tegra.c
+ *
+ * Copyright (c) 2014, NVIDIA CORPORATION.  All rights reserved.
+ *
+ * Author:
+ *	Mikko Perttunen <mperttunen@nvidia.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/ahci_platform.h>
+#include <linux/reset.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/tegra-powergate.h>
+#include <linux/regulator/consumer.h>
+#include "ahci.h"
+
+#define SATA_CONFIGURATION_0				0x180
+#define SATA_CONFIGURATION_EN_FPCI			BIT(0)
+
+#define SCFG_OFFSET					0x1000
+
+#define T_SATA0_CFG_1					0x04
+#define T_SATA0_CFG_1_IO_SPACE				BIT(0)
+#define T_SATA0_CFG_1_MEMORY_SPACE			BIT(1)
+#define T_SATA0_CFG_1_BUS_MASTER			BIT(2)
+#define T_SATA0_CFG_1_SERR				BIT(8)
+
+#define T_SATA0_CFG_9					0x24
+#define T_SATA0_CFG_9_BASE_ADDRESS_SHIFT		13
+
+#define SATA_FPCI_BAR5					0x94
+#define SATA_FPCI_BAR5_START_SHIFT			4
+
+#define SATA_INTR_MASK					0x188
+#define SATA_INTR_MASK_IP_INT_MASK			BIT(16)
+
+#define T_SATA0_AHCI_HBA_CAP_BKDR			0x300
+
+#define T_SATA0_BKDOOR_CC				0x4a4
+
+#define T_SATA0_CFG_SATA				0x54c
+#define T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN		BIT(12)
+
+#define T_SATA0_CFG_MISC				0x550
+
+#define T_SATA0_INDEX					0x680
+
+#define T_SATA0_CHX_PHY_CTRL1_GEN1			0x690
+#define T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK		0xff
+#define T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT		0
+#define T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK		(0xff << 8)
+#define T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT	8
+
+#define T_SATA0_CHX_PHY_CTRL1_GEN2			0x694
+#define T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK		0xff
+#define T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_SHIFT		0
+#define T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK		(0xff << 12)
+#define T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_SHIFT	12
+
+#define T_SATA0_CHX_PHY_CTRL2				0x69c
+#define T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1		0x23
+
+#define T_SATA0_CHX_PHY_CTRL11				0x6d0
+#define T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ		(0x2800 << 16)
+
+#define FUSE_SATA_CALIB					0x124
+#define FUSE_SATA_CALIB_MASK				0x3
+
+struct sata_pad_calibration {
+	u8 gen1_tx_amp;
+	u8 gen1_tx_peak;
+	u8 gen2_tx_amp;
+	u8 gen2_tx_peak;
+};
+
+static const struct sata_pad_calibration tegra124_pad_calibration[] = {
+	{0x18, 0x04, 0x18, 0x0a},
+	{0x0e, 0x04, 0x14, 0x0a},
+	{0x0e, 0x07, 0x1a, 0x0e},
+	{0x14, 0x0e, 0x1a, 0x0e},
+};
+
+struct tegra_ahci_priv {
+	struct platform_device	   *pdev;
+	void __iomem		   *sata_regs;
+	struct reset_control	   *sata_rst;
+	struct reset_control	   *sata_oob_rst;
+	struct reset_control	   *sata_cold_rst;
+	/* Needs special handling, cannot use ahci_platform */
+	struct clk		   *sata_clk;
+	struct regulator_bulk_data supplies[5];
+};
+
+static int tegra_ahci_power_on(struct ahci_host_priv *hpriv)
+{
+	struct tegra_ahci_priv *tegra = hpriv->plat_data;
+	int ret;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(tegra->supplies),
+				    tegra->supplies);
+	if (ret)
+		return ret;
+
+	ret = tegra_powergate_sequence_power_up(TEGRA_POWERGATE_SATA,
+						tegra->sata_clk,
+						tegra->sata_rst);
+	if (ret)
+		goto disable_regulators;
+
+	reset_control_assert(tegra->sata_oob_rst);
+	reset_control_assert(tegra->sata_cold_rst);
+
+	ret = ahci_platform_enable_resources(hpriv);
+	if (ret)
+		goto disable_power;
+
+	reset_control_deassert(tegra->sata_cold_rst);
+	reset_control_deassert(tegra->sata_oob_rst);
+
+	return 0;
+
+disable_power:
+	clk_disable_unprepare(tegra->sata_clk);
+
+	tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
+
+disable_regulators:
+	regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies);
+
+	return ret;
+}
+
+static void tegra_ahci_power_off(struct ahci_host_priv *hpriv)
+{
+	struct tegra_ahci_priv *tegra = hpriv->plat_data;
+
+	ahci_platform_disable_resources(hpriv);
+
+	reset_control_assert(tegra->sata_rst);
+	reset_control_assert(tegra->sata_oob_rst);
+	reset_control_assert(tegra->sata_cold_rst);
+
+	clk_disable_unprepare(tegra->sata_clk);
+	tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
+
+	regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies);
+}
+
+static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv)
+{
+	struct tegra_ahci_priv *tegra = hpriv->plat_data;
+	int ret;
+	unsigned int val;
+	struct sata_pad_calibration calib;
+
+	ret = tegra_ahci_power_on(hpriv);
+	if (ret) {
+		dev_err(&tegra->pdev->dev,
+			"failed to power on AHCI controller: %d\n", ret);
+		return ret;
+	}
+
+	val = readl(tegra->sata_regs + SATA_CONFIGURATION_0);
+	val |= SATA_CONFIGURATION_EN_FPCI;
+	writel(val, tegra->sata_regs + SATA_CONFIGURATION_0);
+
+	/* Pad calibration */
+
+	/* FIXME Always use calibration 0. Change this to read the calibration
+	 * fuse once the fuse driver has landed. */
+	val = 0;
+
+	calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK];
+
+	writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
+
+	val = readl(tegra->sata_regs +
+		SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1);
+	val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK;
+	val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK;
+	val |= calib.gen1_tx_amp <<
+			T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
+	val |= calib.gen1_tx_peak <<
+			T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
+	writel(val, tegra->sata_regs + SCFG_OFFSET +
+		T_SATA0_CHX_PHY_CTRL1_GEN1);
+
+	val = readl(tegra->sata_regs +
+			SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2);
+	val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK;
+	val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK;
+	val |= calib.gen2_tx_amp <<
+			T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
+	val |= calib.gen2_tx_peak <<
+			T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
+	writel(val, tegra->sata_regs + SCFG_OFFSET +
+		T_SATA0_CHX_PHY_CTRL1_GEN2);
+
+	writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ,
+		tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11);
+	writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1,
+		tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2);
+
+	writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
+
+	/* Program controller device ID */
+
+	val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
+	val |= T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN;
+	writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
+
+	writel(0x01060100, tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC);
+
+	val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
+	val &= ~T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN;
+	writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
+
+	/* Enable IO & memory access, bus master mode */
+
+	val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
+	val |= T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE |
+		T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR;
+	writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
+
+	/* Program SATA MMIO */
+
+	writel(0x10000 << SATA_FPCI_BAR5_START_SHIFT,
+	       tegra->sata_regs + SATA_FPCI_BAR5);
+
+	writel(0x08000 << T_SATA0_CFG_9_BASE_ADDRESS_SHIFT,
+	       tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9);
+
+	/* Unmask SATA interrupts */
+
+	val = readl(tegra->sata_regs + SATA_INTR_MASK);
+	val |= SATA_INTR_MASK_IP_INT_MASK;
+	writel(val, tegra->sata_regs + SATA_INTR_MASK);
+
+	return 0;
+}
+
+static void tegra_ahci_controller_deinit(struct ahci_host_priv *hpriv)
+{
+	tegra_ahci_power_off(hpriv);
+}
+
+static void tegra_ahci_host_stop(struct ata_host *host)
+{
+	struct ahci_host_priv *hpriv = host->private_data;
+
+	tegra_ahci_controller_deinit(hpriv);
+}
+
+static struct ata_port_operations ahci_tegra_port_ops = {
+	.inherits	= &ahci_ops,
+	.host_stop	= tegra_ahci_host_stop,
+};
+
+static const struct ata_port_info ahci_tegra_port_info = {
+	.flags		= AHCI_FLAG_COMMON,
+	.pio_mask	= ATA_PIO4,
+	.udma_mask	= ATA_UDMA6,
+	.port_ops	= &ahci_tegra_port_ops,
+};
+
+static const struct of_device_id tegra_ahci_of_match[] = {
+	{ .compatible = "nvidia,tegra124-ahci" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, tegra_ahci_of_match);
+
+static int tegra_ahci_probe(struct platform_device *pdev)
+{
+	struct ahci_host_priv *hpriv;
+	struct tegra_ahci_priv *tegra;
+	struct resource *res;
+	int ret;
+
+	hpriv = ahci_platform_get_resources(pdev);
+	if (IS_ERR(hpriv))
+		return PTR_ERR(hpriv);
+
+	tegra = devm_kzalloc(&pdev->dev, sizeof(*tegra), GFP_KERNEL);
+	if (!tegra)
+		return -ENOMEM;
+
+	hpriv->plat_data = tegra;
+
+	tegra->pdev = pdev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	tegra->sata_regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(tegra->sata_regs))
+		return PTR_ERR(tegra->sata_regs);
+
+	tegra->sata_rst = devm_reset_control_get(&pdev->dev, "sata");
+	if (IS_ERR(tegra->sata_rst)) {
+		dev_err(&pdev->dev, "Failed to get sata reset\n");
+		return PTR_ERR(tegra->sata_rst);
+	}
+
+	tegra->sata_oob_rst = devm_reset_control_get(&pdev->dev, "sata-oob");
+	if (IS_ERR(tegra->sata_oob_rst)) {
+		dev_err(&pdev->dev, "Failed to get sata-oob reset\n");
+		return PTR_ERR(tegra->sata_oob_rst);
+	}
+
+	tegra->sata_cold_rst = devm_reset_control_get(&pdev->dev, "sata-cold");
+	if (IS_ERR(tegra->sata_cold_rst)) {
+		dev_err(&pdev->dev, "Failed to get sata-cold reset\n");
+		return PTR_ERR(tegra->sata_cold_rst);
+	}
+
+	tegra->sata_clk = devm_clk_get(&pdev->dev, "sata");
+	if (IS_ERR(tegra->sata_clk)) {
+		dev_err(&pdev->dev, "Failed to get sata clock\n");
+		return PTR_ERR(tegra->sata_clk);
+	}
+
+	tegra->supplies[0].supply = "avdd";
+	tegra->supplies[1].supply = "hvdd";
+	tegra->supplies[2].supply = "vddio";
+	tegra->supplies[3].supply = "target-5v";
+	tegra->supplies[4].supply = "target-12v";
+
+	ret = devm_regulator_bulk_get(&pdev->dev, ARRAY_SIZE(tegra->supplies),
+				      tegra->supplies);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to get regulators\n");
+		return ret;
+	}
+
+	ret = tegra_ahci_controller_init(hpriv);
+	if (ret)
+		return ret;
+
+	ret = ahci_platform_init_host(pdev, hpriv, &ahci_tegra_port_info);
+	if (ret)
+		goto deinit_controller;
+
+	return 0;
+
+deinit_controller:
+	tegra_ahci_controller_deinit(hpriv);
+
+	return ret;
+};
+
+static struct platform_driver tegra_ahci_driver = {
+	.probe = tegra_ahci_probe,
+	.remove = ata_platform_remove_one,
+	.driver = {
+		.name = "tegra-ahci",
+		.of_match_table = tegra_ahci_of_match,
+	},
+	/* LP0 suspend support not implemented */
+};
+module_platform_driver(tegra_ahci_driver);
+
+MODULE_AUTHOR("Mikko Perttunen <mperttunen@nvidia.com>");
+MODULE_DESCRIPTION("Tegra124 AHCI SATA driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/ata/ahci_xgene.c b/drivers/ata/ahci_xgene.c
index ee3a3659bd9e..bc281115490b 100644
--- a/drivers/ata/ahci_xgene.c
+++ b/drivers/ata/ahci_xgene.c
@@ -67,6 +67,9 @@
 #define PORTAXICFG			0x000000bc
 #define PORTAXICFG_OUTTRANS_SET(dst, src) \
 		(((dst) & ~0x00f00000) | (((u32)(src) << 0x14) & 0x00f00000))
+#define PORTRANSCFG			0x000000c8
+#define PORTRANSCFG_RXWM_SET(dst, src)		\
+		(((dst) & ~0x0000007f) | (((u32)(src)) & 0x0000007f))
 
 /* SATA host controller AXI CSR */
 #define INT_SLV_TMOMASK			0x00000010
@@ -193,11 +196,11 @@ static void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel)
 	/* Disable fix rate */
 	writel(0x0001fffe, mmio + PORTPHY1CFG);
 	readl(mmio + PORTPHY1CFG); /* Force a barrier */
-	writel(0x5018461c, mmio + PORTPHY2CFG);
+	writel(0x28183219, mmio + PORTPHY2CFG);
 	readl(mmio + PORTPHY2CFG); /* Force a barrier */
-	writel(0x1c081907, mmio + PORTPHY3CFG);
+	writel(0x13081008, mmio + PORTPHY3CFG);
 	readl(mmio + PORTPHY3CFG); /* Force a barrier */
-	writel(0x1c080815, mmio + PORTPHY4CFG);
+	writel(0x00480815, mmio + PORTPHY4CFG);
 	readl(mmio + PORTPHY4CFG); /* Force a barrier */
 	/* Set window negotiation */
 	val = readl(mmio + PORTPHY5CFG);
@@ -209,6 +212,10 @@ static void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel)
 	val = PORTAXICFG_OUTTRANS_SET(val, 0xe); /* Set outstanding */
 	writel(val, mmio + PORTAXICFG);
 	readl(mmio + PORTAXICFG); /* Force a barrier */
+	/* Set the watermark threshold of the receive FIFO */
+	val = readl(mmio + PORTRANSCFG);
+	val = PORTRANSCFG_RXWM_SET(val, 0x30);
+	writel(val, mmio + PORTRANSCFG);
 }
 
 /**
@@ -415,7 +422,6 @@ static int xgene_ahci_probe(struct platform_device *pdev)
 	struct ahci_host_priv *hpriv;
 	struct xgene_ahci_context *ctx;
 	struct resource *res;
-	unsigned long hflags;
 	int rc;
 
 	hpriv = ahci_platform_get_resources(pdev);
@@ -474,20 +480,9 @@ static int xgene_ahci_probe(struct platform_device *pdev)
 	/* Configure the host controller */
 	xgene_ahci_hw_init(hpriv);
 
-	/*
-	 * Setup DMA mask. This is preliminary until the DMA range is sorted
-	 * out.
-	 */
-	rc = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(64));
-	if (rc) {
-		dev_err(dev, "Unable to set dma mask\n");
-		goto disable_resources;
-	}
-
-	hflags = AHCI_HFLAG_NO_PMP | AHCI_HFLAG_YES_NCQ;
+	hpriv->flags = AHCI_HFLAG_NO_PMP | AHCI_HFLAG_YES_NCQ;
 
-	rc = ahci_platform_init_host(pdev, hpriv, &xgene_ahci_port_info,
-				     hflags, 0, 0);
+	rc = ahci_platform_init_host(pdev, hpriv, &xgene_ahci_port_info);
 	if (rc)
 		goto disable_resources;
 
diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c
index d72ce0470309..b784e9de426a 100644
--- a/drivers/ata/libahci.c
+++ b/drivers/ata/libahci.c
@@ -382,8 +382,6 @@ static ssize_t ahci_show_em_supported(struct device *dev,
  *	ahci_save_initial_config - Save and fixup initial config values
  *	@dev: target AHCI device
  *	@hpriv: host private area to store config values
- *	@force_port_map: force port map to a specified value
- *	@mask_port_map: mask out particular bits from port map
  *
  *	Some registers containing configuration info might be setup by
  *	BIOS and might be cleared on reset.  This function saves the
@@ -398,10 +396,7 @@ static ssize_t ahci_show_em_supported(struct device *dev,
  *	LOCKING:
  *	None.
  */
-void ahci_save_initial_config(struct device *dev,
-			      struct ahci_host_priv *hpriv,
-			      unsigned int force_port_map,
-			      unsigned int mask_port_map)
+void ahci_save_initial_config(struct device *dev, struct ahci_host_priv *hpriv)
 {
 	void __iomem *mmio = hpriv->mmio;
 	u32 cap, cap2, vers, port_map;
@@ -468,17 +463,17 @@ void ahci_save_initial_config(struct device *dev,
 		cap &= ~HOST_CAP_FBS;
 	}
 
-	if (force_port_map && port_map != force_port_map) {
+	if (hpriv->force_port_map && port_map != hpriv->force_port_map) {
 		dev_info(dev, "forcing port_map 0x%x -> 0x%x\n",
-			 port_map, force_port_map);
-		port_map = force_port_map;
+			 port_map, hpriv->force_port_map);
+		port_map = hpriv->force_port_map;
 	}
 
-	if (mask_port_map) {
+	if (hpriv->mask_port_map) {
 		dev_warn(dev, "masking port_map 0x%x -> 0x%x\n",
 			port_map,
-			port_map & mask_port_map);
-		port_map &= mask_port_map;
+			port_map & hpriv->mask_port_map);
+		port_map &= hpriv->mask_port_map;
 	}
 
 	/* cross check port_map and cap.n_ports */
diff --git a/drivers/ata/libahci_platform.c b/drivers/ata/libahci_platform.c
index b0077589f065..5b92c290e6c6 100644
--- a/drivers/ata/libahci_platform.c
+++ b/drivers/ata/libahci_platform.c
@@ -39,6 +39,67 @@ static struct scsi_host_template ahci_platform_sht = {
 };
 
 /**
+ * ahci_platform_enable_phys - Enable PHYs
+ * @hpriv: host private area to store config values
+ *
+ * This function enables all the PHYs found in hpriv->phys, if any.
+ * If a PHY fails to be enabled, it disables all the PHYs already
+ * enabled in reverse order and returns an error.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_enable_phys(struct ahci_host_priv *hpriv)
+{
+	int rc, i;
+
+	for (i = 0; i < hpriv->nports; i++) {
+		if (!hpriv->phys[i])
+			continue;
+
+		rc = phy_init(hpriv->phys[i]);
+		if (rc)
+			goto disable_phys;
+
+		rc = phy_power_on(hpriv->phys[i]);
+		if (rc) {
+			phy_exit(hpriv->phys[i]);
+			goto disable_phys;
+		}
+	}
+
+	return 0;
+
+disable_phys:
+	while (--i >= 0) {
+		phy_power_off(hpriv->phys[i]);
+		phy_exit(hpriv->phys[i]);
+	}
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_enable_phys);
+
+/**
+ * ahci_platform_disable_phys - Disable PHYs
+ * @hpriv: host private area to store config values
+ *
+ * This function disables all PHYs found in hpriv->phys.
+ */
+void ahci_platform_disable_phys(struct ahci_host_priv *hpriv)
+{
+	int i;
+
+	for (i = 0; i < hpriv->nports; i++) {
+		if (!hpriv->phys[i])
+			continue;
+
+		phy_power_off(hpriv->phys[i]);
+		phy_exit(hpriv->phys[i]);
+	}
+}
+EXPORT_SYMBOL_GPL(ahci_platform_disable_phys);
+
+/**
  * ahci_platform_enable_clks - Enable platform clocks
  * @hpriv: host private area to store config values
  *
@@ -92,7 +153,7 @@ EXPORT_SYMBOL_GPL(ahci_platform_disable_clks);
  * following order:
  * 1) Regulator
  * 2) Clocks (through ahci_platform_enable_clks)
- * 3) Phy
+ * 3) Phys
  *
  * If resource enabling fails at any point the previous enabled resources
  * are disabled in reverse order.
@@ -114,17 +175,9 @@ int ahci_platform_enable_resources(struct ahci_host_priv *hpriv)
 	if (rc)
 		goto disable_regulator;
 
-	if (hpriv->phy) {
-		rc = phy_init(hpriv->phy);
-		if (rc)
-			goto disable_clks;
-
-		rc = phy_power_on(hpriv->phy);
-		if (rc) {
-			phy_exit(hpriv->phy);
-			goto disable_clks;
-		}
-	}
+	rc = ahci_platform_enable_phys(hpriv);
+	if (rc)
+		goto disable_clks;
 
 	return 0;
 
@@ -144,16 +197,13 @@ EXPORT_SYMBOL_GPL(ahci_platform_enable_resources);
  *
  * This function disables all ahci_platform managed resources in the
  * following order:
- * 1) Phy
+ * 1) Phys
  * 2) Clocks (through ahci_platform_disable_clks)
  * 3) Regulator
  */
 void ahci_platform_disable_resources(struct ahci_host_priv *hpriv)
 {
-	if (hpriv->phy) {
-		phy_power_off(hpriv->phy);
-		phy_exit(hpriv->phy);
-	}
+	ahci_platform_disable_phys(hpriv);
 
 	ahci_platform_disable_clks(hpriv);
 
@@ -187,7 +237,7 @@ static void ahci_platform_put_resources(struct device *dev, void *res)
  * 2) regulator for controlling the targets power (optional)
  * 3) 0 - AHCI_MAX_CLKS clocks, as specified in the devs devicetree node,
  *    or for non devicetree enabled platforms a single clock
- *	4) phy (optional)
+ *	4) phys (optional)
  *
  * RETURNS:
  * The allocated ahci_host_priv on success, otherwise an ERR_PTR value
@@ -197,7 +247,9 @@ struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct ahci_host_priv *hpriv;
 	struct clk *clk;
-	int i, rc = -ENOMEM;
+	struct device_node *child;
+	int i, enabled_ports = 0, rc = -ENOMEM;
+	u32 mask_port_map = 0;
 
 	if (!devres_open_group(dev, NULL, GFP_KERNEL))
 		return ERR_PTR(-ENOMEM);
@@ -246,28 +298,89 @@ struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev)
 		hpriv->clks[i] = clk;
 	}
 
-	hpriv->phy = devm_phy_get(dev, "sata-phy");
-	if (IS_ERR(hpriv->phy)) {
-		rc = PTR_ERR(hpriv->phy);
-		switch (rc) {
-		case -ENOSYS:
-			/* No PHY support. Check if PHY is required. */
-			if (of_find_property(dev->of_node, "phys", NULL)) {
-				dev_err(dev, "couldn't get sata-phy: ENOSYS\n");
+	hpriv->nports = of_get_child_count(dev->of_node);
+
+	if (hpriv->nports) {
+		hpriv->phys = devm_kzalloc(dev,
+					   hpriv->nports * sizeof(*hpriv->phys),
+					   GFP_KERNEL);
+		if (!hpriv->phys) {
+			rc = -ENOMEM;
+			goto err_out;
+		}
+
+		for_each_child_of_node(dev->of_node, child) {
+			u32 port;
+
+			if (!of_device_is_available(child))
+				continue;
+
+			if (of_property_read_u32(child, "reg", &port)) {
+				rc = -EINVAL;
 				goto err_out;
 			}
-		case -ENODEV:
-			/* continue normally */
-			hpriv->phy = NULL;
-			break;
 
-		case -EPROBE_DEFER:
-			goto err_out;
+			if (port >= hpriv->nports) {
+				dev_warn(dev, "invalid port number %d\n", port);
+				continue;
+			}
+
+			mask_port_map |= BIT(port);
 
-		default:
-			dev_err(dev, "couldn't get sata-phy\n");
+			hpriv->phys[port] = devm_of_phy_get(dev, child, NULL);
+			if (IS_ERR(hpriv->phys[port])) {
+				rc = PTR_ERR(hpriv->phys[port]);
+				dev_err(dev,
+					"couldn't get PHY in node %s: %d\n",
+					child->name, rc);
+				goto err_out;
+			}
+
+			enabled_ports++;
+		}
+		if (!enabled_ports) {
+			dev_warn(dev, "No port enabled\n");
+			rc = -ENODEV;
 			goto err_out;
 		}
+
+		if (!hpriv->mask_port_map)
+			hpriv->mask_port_map = mask_port_map;
+	} else {
+		/*
+		 * If no sub-node was found, keep this for device tree
+		 * compatibility
+		 */
+		struct phy *phy = devm_phy_get(dev, "sata-phy");
+		if (!IS_ERR(phy)) {
+			hpriv->phys = devm_kzalloc(dev, sizeof(*hpriv->phys),
+						   GFP_KERNEL);
+			if (!hpriv->phys) {
+				rc = -ENOMEM;
+				goto err_out;
+			}
+
+			hpriv->phys[0] = phy;
+			hpriv->nports = 1;
+		} else {
+			rc = PTR_ERR(phy);
+			switch (rc) {
+				case -ENOSYS:
+					/* No PHY support. Check if PHY is required. */
+					if (of_find_property(dev->of_node, "phys", NULL)) {
+						dev_err(dev, "couldn't get sata-phy: ENOSYS\n");
+						goto err_out;
+					}
+				case -ENODEV:
+					/* continue normally */
+					hpriv->phys = NULL;
+					break;
+
+				default:
+					goto err_out;
+
+			}
+		}
 	}
 
 	pm_runtime_enable(dev);
@@ -288,12 +401,9 @@ EXPORT_SYMBOL_GPL(ahci_platform_get_resources);
  * @pdev: platform device pointer for the host
  * @hpriv: ahci-host private data for the host
  * @pi_template: template for the ata_port_info to use
- * @host_flags: ahci host flags used in ahci_host_priv
- * @force_port_map: param passed to ahci_save_initial_config
- * @mask_port_map: param passed to ahci_save_initial_config
  *
  * This function does all the usual steps needed to bring up an
- * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
+ * ahci-platform host, note any necessary resources (ie clks, phys, etc.)
  * must be initialized / enabled before calling this.
  *
  * RETURNS:
@@ -301,10 +411,7 @@ EXPORT_SYMBOL_GPL(ahci_platform_get_resources);
  */
 int ahci_platform_init_host(struct platform_device *pdev,
 			    struct ahci_host_priv *hpriv,
-			    const struct ata_port_info *pi_template,
-			    unsigned long host_flags,
-			    unsigned int force_port_map,
-			    unsigned int mask_port_map)
+			    const struct ata_port_info *pi_template)
 {
 	struct device *dev = &pdev->dev;
 	struct ata_port_info pi = *pi_template;
@@ -319,10 +426,9 @@ int ahci_platform_init_host(struct platform_device *pdev,
 	}
 
 	/* prepare host */
-	pi.private_data = (void *)host_flags;
-	hpriv->flags |= host_flags;
+	pi.private_data = (void *)(unsigned long)hpriv->flags;
 
-	ahci_save_initial_config(dev, hpriv, force_port_map, mask_port_map);
+	ahci_save_initial_config(dev, hpriv);
 
 	if (hpriv->cap & HOST_CAP_NCQ)
 		pi.flags |= ATA_FLAG_NCQ;
@@ -369,6 +475,19 @@ int ahci_platform_init_host(struct platform_device *pdev,
 			ap->ops = &ata_dummy_port_ops;
 	}
 
+	if (hpriv->cap & HOST_CAP_64) {
+		rc = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(64));
+		if (rc) {
+			rc = dma_coerce_mask_and_coherent(dev,
+							  DMA_BIT_MASK(32));
+			if (rc) {
+				dev_err(dev, "Failed to enable 64-bit DMA.\n");
+				return rc;
+			}
+			dev_warn(dev, "Enable 32-bit DMA instead of 64-bit.\n");
+		}
+	}
+
 	rc = ahci_reset_controller(host);
 	if (rc)
 		return rc;
@@ -399,7 +518,7 @@ static void ahci_host_stop(struct ata_host *host)
  * @dev: device pointer for the host
  *
  * This function does all the usual steps needed to suspend an
- * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
+ * ahci-platform host, note any necessary resources (ie clks, phys, etc.)
  * must be disabled after calling this.
  *
  * RETURNS:
@@ -436,7 +555,7 @@ EXPORT_SYMBOL_GPL(ahci_platform_suspend_host);
  * @dev: device pointer for the host
  *
  * This function does all the usual steps needed to resume an ahci-platform
- * host, note any necessary resources (ie clks, phy, etc.)  must be
+ * host, note any necessary resources (ie clks, phys, etc.)  must be
  * initialized / enabled before calling this.
  *
  * RETURNS:
diff --git a/drivers/ata/pata_samsung_cf.c b/drivers/ata/pata_samsung_cf.c
index fb528831fb92..2578fc16960a 100644
--- a/drivers/ata/pata_samsung_cf.c
+++ b/drivers/ata/pata_samsung_cf.c
@@ -54,7 +54,6 @@
 
 enum s3c_cpu_type {
 	TYPE_S3C64XX,
-	TYPE_S5PC100,
 	TYPE_S5PV210,
 };
 
@@ -476,10 +475,6 @@ static void pata_s3c_hwinit(struct s3c_ide_info *info,
 		writel(0x1b, info->ide_addr + S3C_ATA_IRQ_MSK);
 		break;
 
-	case TYPE_S5PC100:
-		pata_s3c_cfg_mode(info->sfr_addr);
-		/* FALLTHROUGH */
-
 	case TYPE_S5PV210:
 		/* Configure as little endian */
 		pata_s3c_set_endian(info->ide_addr, 0);
@@ -549,11 +544,6 @@ static int __init pata_s3c_probe(struct platform_device *pdev)
 		info->sfr_addr = info->ide_addr + 0x1800;
 		info->ide_addr += 0x1900;
 		info->fifo_status_reg = 0x94;
-	} else if (cpu_type == TYPE_S5PC100) {
-		ap->ops = &pata_s5p_port_ops;
-		info->sfr_addr = info->ide_addr + 0x1800;
-		info->ide_addr += 0x1900;
-		info->fifo_status_reg = 0x84;
 	} else {
 		ap->ops = &pata_s5p_port_ops;
 		info->fifo_status_reg = 0x84;
@@ -653,9 +643,6 @@ static struct platform_device_id pata_s3c_driver_ids[] = {
 		.name		= "s3c64xx-pata",
 		.driver_data	= TYPE_S3C64XX,
 	}, {
-		.name		= "s5pc100-pata",
-		.driver_data	= TYPE_S5PC100,
-	}, {
 		.name		= "s5pv210-pata",
 		.driver_data	= TYPE_S5PV210,
 	},
diff --git a/drivers/ata/sata_fsl.c b/drivers/ata/sata_fsl.c
index 616a6d2ac20c..07bc7e4dbd04 100644
--- a/drivers/ata/sata_fsl.c
+++ b/drivers/ata/sata_fsl.c
@@ -734,13 +734,12 @@ static int sata_fsl_port_start(struct ata_port *ap)
 	if (!pp)
 		return -ENOMEM;
 
-	mem = dma_alloc_coherent(dev, SATA_FSL_PORT_PRIV_DMA_SZ, &mem_dma,
-				 GFP_KERNEL);
+	mem = dma_zalloc_coherent(dev, SATA_FSL_PORT_PRIV_DMA_SZ, &mem_dma,
+				  GFP_KERNEL);
 	if (!mem) {
 		kfree(pp);
 		return -ENOMEM;
 	}
-	memset(mem, 0, SATA_FSL_PORT_PRIV_DMA_SZ);
 
 	pp->cmdslot = mem;
 	pp->cmdslot_paddr = mem_dma;
diff --git a/drivers/ata/sata_highbank.c b/drivers/ata/sata_highbank.c
index 65965cf5af06..da3bc2709c63 100644
--- a/drivers/ata/sata_highbank.c
+++ b/drivers/ata/sata_highbank.c
@@ -512,7 +512,7 @@ static int ahci_highbank_probe(struct platform_device *pdev)
 		return rc;
 
 
-	ahci_save_initial_config(dev, hpriv, 0, 0);
+	ahci_save_initial_config(dev, hpriv);
 
 	/* prepare host */
 	if (hpriv->cap & HOST_CAP_NCQ)
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index 0534890f118a..d81b20ddb527 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -1154,8 +1154,8 @@ static irqreturn_t sil24_interrupt(int irq, void *dev_instance)
 	status = readl(host_base + HOST_IRQ_STAT);
 
 	if (status == 0xffffffff) {
-		printk(KERN_ERR DRV_NAME ": IRQ status == 0xffffffff, "
-		       "PCI fault or device removal?\n");
+		dev_err(host->dev, "IRQ status == 0xffffffff, "
+			"PCI fault or device removal?\n");
 		goto out;
 	}
 
diff --git a/include/linux/ahci_platform.h b/include/linux/ahci_platform.h
index 6dfd51a04d77..09a947e8bc87 100644
--- a/include/linux/ahci_platform.h
+++ b/include/linux/ahci_platform.h
@@ -43,10 +43,7 @@ struct ahci_host_priv *ahci_platform_get_resources(
 	struct platform_device *pdev);
 int ahci_platform_init_host(struct platform_device *pdev,
 			    struct ahci_host_priv *hpriv,
-			    const struct ata_port_info *pi_template,
-			    unsigned long host_flags,
-			    unsigned int force_port_map,
-			    unsigned int mask_port_map);
+			    const struct ata_port_info *pi_template);
 
 int ahci_platform_suspend_host(struct device *dev);
 int ahci_platform_resume_host(struct device *dev);
diff --git a/include/linux/platform_data/ata-samsung_cf.h b/include/linux/platform_data/ata-samsung_cf.h
index c2049e3d7444..748e71642c4a 100644
--- a/include/linux/platform_data/ata-samsung_cf.h
+++ b/include/linux/platform_data/ata-samsung_cf.h
@@ -29,7 +29,6 @@ extern void s3c_ide_set_platdata(struct s3c_ide_platdata *pdata);
 
 /* architecture-specific IDE configuration */
 extern void s3c64xx_ide_setup_gpio(void);
-extern void s5pc100_ide_setup_gpio(void);
 extern void s5pv210_ide_setup_gpio(void);
 
 #endif /*__ATA_SAMSUNG_CF_H */