summaryrefslogtreecommitdiff
path: root/kernel/kprobes.c
AgeCommit message (Collapse)AuthorFilesLines
2023-02-21x86/kprobes: Fix arch_check_optimized_kprobe check within optimized_kprobe rangeYang Jihong1-1/+1
When arch_prepare_optimized_kprobe calculating jump destination address, it copies original instructions from jmp-optimized kprobe (see __recover_optprobed_insn), and calculated based on length of original instruction. arch_check_optimized_kprobe does not check KPROBE_FLAG_OPTIMATED when checking whether jmp-optimized kprobe exists. As a result, setup_detour_execution may jump to a range that has been overwritten by jump destination address, resulting in an inval opcode error. For example, assume that register two kprobes whose addresses are <func+9> and <func+11> in "func" function. The original code of "func" function is as follows: 0xffffffff816cb5e9 <+9>: push %r12 0xffffffff816cb5eb <+11>: xor %r12d,%r12d 0xffffffff816cb5ee <+14>: test %rdi,%rdi 0xffffffff816cb5f1 <+17>: setne %r12b 0xffffffff816cb5f5 <+21>: push %rbp 1.Register the kprobe for <func+11>, assume that is kp1, corresponding optimized_kprobe is op1. After the optimization, "func" code changes to: 0xffffffff816cc079 <+9>: push %r12 0xffffffff816cc07b <+11>: jmp 0xffffffffa0210000 0xffffffff816cc080 <+16>: incl 0xf(%rcx) 0xffffffff816cc083 <+19>: xchg %eax,%ebp 0xffffffff816cc084 <+20>: (bad) 0xffffffff816cc085 <+21>: push %rbp Now op1->flags == KPROBE_FLAG_OPTIMATED; 2. Register the kprobe for <func+9>, assume that is kp2, corresponding optimized_kprobe is op2. register_kprobe(kp2) register_aggr_kprobe alloc_aggr_kprobe __prepare_optimized_kprobe arch_prepare_optimized_kprobe __recover_optprobed_insn // copy original bytes from kp1->optinsn.copied_insn, // jump address = <func+14> 3. disable kp1: disable_kprobe(kp1) __disable_kprobe ... if (p == orig_p || aggr_kprobe_disabled(orig_p)) { ret = disarm_kprobe(orig_p, true) // add op1 in unoptimizing_list, not unoptimized orig_p->flags |= KPROBE_FLAG_DISABLED; // op1->flags == KPROBE_FLAG_OPTIMATED | KPROBE_FLAG_DISABLED ... 4. unregister kp2 __unregister_kprobe_top ... if (!kprobe_disabled(ap) && !kprobes_all_disarmed) { optimize_kprobe(op) ... if (arch_check_optimized_kprobe(op) < 0) // because op1 has KPROBE_FLAG_DISABLED, here not return return; p->kp.flags |= KPROBE_FLAG_OPTIMIZED; // now op2 has KPROBE_FLAG_OPTIMIZED } "func" code now is: 0xffffffff816cc079 <+9>: int3 0xffffffff816cc07a <+10>: push %rsp 0xffffffff816cc07b <+11>: jmp 0xffffffffa0210000 0xffffffff816cc080 <+16>: incl 0xf(%rcx) 0xffffffff816cc083 <+19>: xchg %eax,%ebp 0xffffffff816cc084 <+20>: (bad) 0xffffffff816cc085 <+21>: push %rbp 5. if call "func", int3 handler call setup_detour_execution: if (p->flags & KPROBE_FLAG_OPTIMIZED) { ... regs->ip = (unsigned long)op->optinsn.insn + TMPL_END_IDX; ... } The code for the destination address is 0xffffffffa021072c: push %r12 0xffffffffa021072e: xor %r12d,%r12d 0xffffffffa0210731: jmp 0xffffffff816cb5ee <func+14> However, <func+14> is not a valid start instruction address. As a result, an error occurs. Link: https://lore.kernel.org/all/20230216034247.32348-3-yangjihong1@huawei.com/ Fixes: f66c0447cca1 ("kprobes: Set unoptimized flag after unoptimizing code") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Cc: stable@vger.kernel.org Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2023-02-21x86/kprobes: Fix __recover_optprobed_insn check optimizing logicYang Jihong1-1/+1
Since the following commit: commit f66c0447cca1 ("kprobes: Set unoptimized flag after unoptimizing code") modified the update timing of the KPROBE_FLAG_OPTIMIZED, a optimized_kprobe may be in the optimizing or unoptimizing state when op.kp->flags has KPROBE_FLAG_OPTIMIZED and op->list is not empty. The __recover_optprobed_insn check logic is incorrect, a kprobe in the unoptimizing state may be incorrectly determined as unoptimizing. As a result, incorrect instructions are copied. The optprobe_queued_unopt function needs to be exported for invoking in arch directory. Link: https://lore.kernel.org/all/20230216034247.32348-2-yangjihong1@huawei.com/ Fixes: f66c0447cca1 ("kprobes: Set unoptimized flag after unoptimizing code") Cc: stable@vger.kernel.org Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2023-02-21kprobes: Fix to handle forcibly unoptimized kprobes on freeing_listMasami Hiramatsu (Google)1-13/+10
Since forcibly unoptimized kprobes will be put on the freeing_list directly in the unoptimize_kprobe(), do_unoptimize_kprobes() must continue to check the freeing_list even if unoptimizing_list is empty. This bug can happen if a kprobe is put in an instruction which is in the middle of the jump-replaced instruction sequence of an optprobe, *and* the optprobe is recently unregistered and queued on unoptimizing_list. In this case, the optprobe will be unoptimized forcibly (means immediately) and put it into the freeing_list, expecting the optprobe will be handled in do_unoptimize_kprobe(). But if there is no other optprobes on the unoptimizing_list, current code returns from the do_unoptimize_kprobe() soon and does not handle the optprobe which is on the freeing_list. Then the optprobe will hit the WARN_ON_ONCE() in the do_free_cleaned_kprobes(), because it is not handled in the latter loop of the do_unoptimize_kprobe(). To solve this issue, do not return from do_unoptimize_kprobes() immediately even if unoptimizing_list is empty. Moreover, this change affects another case. kill_optimized_kprobes() expects kprobe_optimizer() will just free the optprobe on freeing_list. So I changed it to just do list_move() to freeing_list if optprobes are on unoptimizing list. And the do_unoptimize_kprobe() will skip arch_disarm_kprobe() if the probe on freeing_list has gone flag. Link: https://lore.kernel.org/all/Y8URdIfVr3pq2X8w@xpf.sh.intel.com/ Link: https://lore.kernel.org/all/167448024501.3253718.13037333683110512967.stgit@devnote3/ Fixes: e4add247789e ("kprobes: Fix optimize_kprobe()/unoptimize_kprobe() cancellation logic") Reported-by: Pengfei Xu <pengfei.xu@intel.com> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Cc: stable@vger.kernel.org Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2022-12-15kprobes: kretprobe events missing on 2-core KVM guestwuqiang1-6/+2
Default value of maxactive is set as num_possible_cpus() for nonpreemptable systems. For a 2-core system, only 2 kretprobe instances would be allocated in default, then these 2 instances for execve kretprobe are very likely to be used up with a pipelined command. Here's the testcase: a shell script was added to crontab, and the content of the script is: #!/bin/sh do_something_magic `tr -dc a-z < /dev/urandom | head -c 10` cron will trigger a series of program executions (4 times every hour). Then events loss would be noticed normally after 3-4 hours of testings. The issue is caused by a burst of series of execve requests. The best number of kretprobe instances could be different case by case, and should be user's duty to determine, but num_possible_cpus() as the default value is inadequate especially for systems with small number of cpus. This patch enables the logic for preemption as default, thus increases the minimum of maxactive to 10 for nonpreemptable systems. Link: https://lore.kernel.org/all/20221110081502.492289-1-wuqiang.matt@bytedance.com/ Signed-off-by: wuqiang <wuqiang.matt@bytedance.com> Reviewed-by: Solar Designer <solar@openwall.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2022-11-28kprobes: Fix check for probe enabled in kill_kprobe()Li Huafei1-8/+8
In kill_kprobe(), the check whether disarm_kprobe_ftrace() needs to be called always fails. This is because before that we set the KPROBE_FLAG_GONE flag for kprobe so that "!kprobe_disabled(p)" is always false. The disarm_kprobe_ftrace() call introduced by commit: 0cb2f1372baa ("kprobes: Fix NULL pointer dereference at kprobe_ftrace_handler") to fix the NULL pointer reference problem. When the probe is enabled, if we do not disarm it, this problem still exists. Fix it by putting the probe enabled check before setting the KPROBE_FLAG_GONE flag. Link: https://lore.kernel.org/all/20221126114316.201857-1-lihuafei1@huawei.com/ Fixes: 3031313eb3d54 ("kprobes: Fix to check probe enabled before disarm_kprobe_ftrace()") Signed-off-by: Li Huafei <lihuafei1@huawei.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2022-11-18kprobes: Skip clearing aggrprobe's post_handler in kprobe-on-ftrace caseLi Huafei1-1/+7
In __unregister_kprobe_top(), if the currently unregistered probe has post_handler but other child probes of the aggrprobe do not have post_handler, the post_handler of the aggrprobe is cleared. If this is a ftrace-based probe, there is a problem. In later calls to disarm_kprobe(), we will use kprobe_ftrace_ops because post_handler is NULL. But we're armed with kprobe_ipmodify_ops. This triggers a WARN in __disarm_kprobe_ftrace() and may even cause use-after-free: Failed to disarm kprobe-ftrace at kernel_clone+0x0/0x3c0 (error -2) WARNING: CPU: 5 PID: 137 at kernel/kprobes.c:1135 __disarm_kprobe_ftrace.isra.21+0xcf/0xe0 Modules linked in: testKprobe_007(-) CPU: 5 PID: 137 Comm: rmmod Not tainted 6.1.0-rc4-dirty #18 [...] Call Trace: <TASK> __disable_kprobe+0xcd/0xe0 __unregister_kprobe_top+0x12/0x150 ? mutex_lock+0xe/0x30 unregister_kprobes.part.23+0x31/0xa0 unregister_kprobe+0x32/0x40 __x64_sys_delete_module+0x15e/0x260 ? do_user_addr_fault+0x2cd/0x6b0 do_syscall_64+0x3a/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd [...] For the kprobe-on-ftrace case, we keep the post_handler setting to identify this aggrprobe armed with kprobe_ipmodify_ops. This way we can disarm it correctly. Link: https://lore.kernel.org/all/20221112070000.35299-1-lihuafei1@huawei.com/ Fixes: 0bc11ed5ab60 ("kprobes: Allow kprobes coexist with livepatch") Reported-by: Zhao Gongyi <zhaogongyi@huawei.com> Suggested-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Li Huafei <lihuafei1@huawei.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2022-11-04kprobe: reverse kp->flags when arm_kprobe failedLi Qiang1-1/+4
In aggregate kprobe case, when arm_kprobe failed, we need set the kp->flags with KPROBE_FLAG_DISABLED again. If not, the 'kp' kprobe will been considered as enabled but it actually not enabled. Link: https://lore.kernel.org/all/20220902155820.34755-1-liq3ea@163.com/ Fixes: 12310e343755 ("kprobes: Propagate error from arm_kprobe_ftrace()") Cc: stable@vger.kernel.org Signed-off-by: Li Qiang <liq3ea@163.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2022-10-03Merge https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextJakub Kicinski1-1/+5
Daniel Borkmann says: ==================== pull-request: bpf-next 2022-10-03 We've added 143 non-merge commits during the last 27 day(s) which contain a total of 151 files changed, 8321 insertions(+), 1402 deletions(-). The main changes are: 1) Add kfuncs for PKCS#7 signature verification from BPF programs, from Roberto Sassu. 2) Add support for struct-based arguments for trampoline based BPF programs, from Yonghong Song. 3) Fix entry IP for kprobe-multi and trampoline probes under IBT enabled, from Jiri Olsa. 4) Batch of improvements to veristat selftest tool in particular to add CSV output, a comparison mode for CSV outputs and filtering, from Andrii Nakryiko. 5) Add preparatory changes needed for the BPF core for upcoming BPF HID support, from Benjamin Tissoires. 6) Support for direct writes to nf_conn's mark field from tc and XDP BPF program types, from Daniel Xu. 7) Initial batch of documentation improvements for BPF insn set spec, from Dave Thaler. 8) Add a new BPF_MAP_TYPE_USER_RINGBUF map which provides single-user-space-producer / single-kernel-consumer semantics for BPF ring buffer, from David Vernet. 9) Follow-up fixes to BPF allocator under RT to always use raw spinlock for the BPF hashtab's bucket lock, from Hou Tao. 10) Allow creating an iterator that loops through only the resources of one task/thread instead of all, from Kui-Feng Lee. 11) Add support for kptrs in the per-CPU arraymap, from Kumar Kartikeya Dwivedi. 12) Add a new kfunc helper for nf to set src/dst NAT IP/port in a newly allocated CT entry which is not yet inserted, from Lorenzo Bianconi. 13) Remove invalid recursion check for struct_ops for TCP congestion control BPF programs, from Martin KaFai Lau. 14) Fix W^X issue with BPF trampoline and BPF dispatcher, from Song Liu. 15) Fix percpu_counter leakage in BPF hashtab allocation error path, from Tetsuo Handa. 16) Various cleanups in BPF selftests to use preferred ASSERT_* macros, from Wang Yufen. 17) Add invocation for cgroup/connect{4,6} BPF programs for ICMP pings, from YiFei Zhu. 18) Lift blinding decision under bpf_jit_harden = 1 to bpf_capable(), from Yauheni Kaliuta. 19) Various libbpf fixes and cleanups including a libbpf NULL pointer deref, from Xin Liu. * https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (143 commits) net: netfilter: move bpf_ct_set_nat_info kfunc in nf_nat_bpf.c Documentation: bpf: Add implementation notes documentations to table of contents bpf, docs: Delete misformatted table. selftests/xsk: Fix double free bpftool: Fix error message of strerror libbpf: Fix overrun in netlink attribute iteration selftests/bpf: Fix spelling mistake "unpriviledged" -> "unprivileged" samples/bpf: Fix typo in xdp_router_ipv4 sample bpftool: Remove unused struct event_ring_info bpftool: Remove unused struct btf_attach_point bpf, docs: Add TOC and fix formatting. bpf, docs: Add Clang note about BPF_ALU bpf, docs: Move Clang notes to a separate file bpf, docs: Linux byteswap note bpf, docs: Move legacy packet instructions to a separate file selftests/bpf: Check -EBUSY for the recurred bpf_setsockopt(TCP_CONGESTION) bpf: tcp: Stop bpf_setsockopt(TCP_CONGESTION) in init ops to recur itself bpf: Refactor bpf_setsockopt(TCP_CONGESTION) handling into another function bpf: Move the "cdg" tcp-cc check to the common sol_tcp_sockopt() bpf: Add __bpf_prog_{enter,exit}_struct_ops for struct_ops trampoline ... ==================== Link: https://lore.kernel.org/r/20221003194915.11847-1-daniel@iogearbox.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-26kprobes: Add new KPROBE_FLAG_ON_FUNC_ENTRY kprobe flagJiri Olsa1-1/+5
Adding KPROBE_FLAG_ON_FUNC_ENTRY kprobe flag to indicate that attach address is on function entry. This is used in following changes in get_func_ip helper to return correct function address. Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Link: https://lore.kernel.org/r/20220926153340.1621984-2-jolsa@kernel.org Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2022-09-08kprobes: Prohibit probes in gate areaChristian A. Ehrhardt1-0/+1
The system call gate area counts as kernel text but trying to install a kprobe in this area fails with an Oops later on. To fix this explicitly disallow the gate area for kprobes. Found by syzkaller with the following reproducer: perf_event_open$cgroup(&(0x7f00000001c0)={0x6, 0x80, 0x0, 0x0, 0x0, 0x0, 0x80ffff, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, @perf_config_ext={0x0, 0xffffffffff600000}}, 0xffffffffffffffff, 0x0, 0xffffffffffffffff, 0x0) Sample report: BUG: unable to handle page fault for address: fffffbfff3ac6000 PGD 6dfcb067 P4D 6dfcb067 PUD 6df8f067 PMD 6de4d067 PTE 0 Oops: 0000 [#1] PREEMPT SMP KASAN NOPTI CPU: 0 PID: 21978 Comm: syz-executor.2 Not tainted 6.0.0-rc3-00363-g7726d4c3e60b-dirty #6 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:__insn_get_emulate_prefix arch/x86/lib/insn.c:91 [inline] RIP: 0010:insn_get_emulate_prefix arch/x86/lib/insn.c:106 [inline] RIP: 0010:insn_get_prefixes.part.0+0xa8/0x1110 arch/x86/lib/insn.c:134 Code: 49 be 00 00 00 00 00 fc ff df 48 8b 40 60 48 89 44 24 08 e9 81 00 00 00 e8 e5 4b 39 ff 4c 89 fa 4c 89 f9 48 c1 ea 03 83 e1 07 <42> 0f b6 14 32 38 ca 7f 08 84 d2 0f 85 06 10 00 00 48 89 d8 48 89 RSP: 0018:ffffc900088bf860 EFLAGS: 00010246 RAX: 0000000000040000 RBX: ffffffff9b9bebc0 RCX: 0000000000000000 RDX: 1ffffffff3ac6000 RSI: ffffc90002d82000 RDI: ffffc900088bf9e8 RBP: ffffffff9d630001 R08: 0000000000000000 R09: ffffc900088bf9e8 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000001 R13: ffffffff9d630000 R14: dffffc0000000000 R15: ffffffff9d630000 FS: 00007f63eef63640(0000) GS:ffff88806d000000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: fffffbfff3ac6000 CR3: 0000000029d90005 CR4: 0000000000770ef0 PKRU: 55555554 Call Trace: <TASK> insn_get_prefixes arch/x86/lib/insn.c:131 [inline] insn_get_opcode arch/x86/lib/insn.c:272 [inline] insn_get_modrm+0x64a/0x7b0 arch/x86/lib/insn.c:343 insn_get_sib+0x29a/0x330 arch/x86/lib/insn.c:421 insn_get_displacement+0x350/0x6b0 arch/x86/lib/insn.c:464 insn_get_immediate arch/x86/lib/insn.c:632 [inline] insn_get_length arch/x86/lib/insn.c:707 [inline] insn_decode+0x43a/0x490 arch/x86/lib/insn.c:747 can_probe+0xfc/0x1d0 arch/x86/kernel/kprobes/core.c:282 arch_prepare_kprobe+0x79/0x1c0 arch/x86/kernel/kprobes/core.c:739 prepare_kprobe kernel/kprobes.c:1160 [inline] register_kprobe kernel/kprobes.c:1641 [inline] register_kprobe+0xb6e/0x1690 kernel/kprobes.c:1603 __register_trace_kprobe kernel/trace/trace_kprobe.c:509 [inline] __register_trace_kprobe+0x26a/0x2d0 kernel/trace/trace_kprobe.c:477 create_local_trace_kprobe+0x1f7/0x350 kernel/trace/trace_kprobe.c:1833 perf_kprobe_init+0x18c/0x280 kernel/trace/trace_event_perf.c:271 perf_kprobe_event_init+0xf8/0x1c0 kernel/events/core.c:9888 perf_try_init_event+0x12d/0x570 kernel/events/core.c:11261 perf_init_event kernel/events/core.c:11325 [inline] perf_event_alloc.part.0+0xf7f/0x36a0 kernel/events/core.c:11619 perf_event_alloc kernel/events/core.c:12059 [inline] __do_sys_perf_event_open+0x4a8/0x2a00 kernel/events/core.c:12157 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x38/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7f63ef7efaed Code: 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f63eef63028 EFLAGS: 00000246 ORIG_RAX: 000000000000012a RAX: ffffffffffffffda RBX: 00007f63ef90ff80 RCX: 00007f63ef7efaed RDX: 0000000000000000 RSI: ffffffffffffffff RDI: 00000000200001c0 RBP: 00007f63ef86019c R08: 0000000000000000 R09: 0000000000000000 R10: ffffffffffffffff R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000002 R14: 00007f63ef90ff80 R15: 00007f63eef43000 </TASK> Modules linked in: CR2: fffffbfff3ac6000 ---[ end trace 0000000000000000 ]--- RIP: 0010:__insn_get_emulate_prefix arch/x86/lib/insn.c:91 [inline] RIP: 0010:insn_get_emulate_prefix arch/x86/lib/insn.c:106 [inline] RIP: 0010:insn_get_prefixes.part.0+0xa8/0x1110 arch/x86/lib/insn.c:134 Code: 49 be 00 00 00 00 00 fc ff df 48 8b 40 60 48 89 44 24 08 e9 81 00 00 00 e8 e5 4b 39 ff 4c 89 fa 4c 89 f9 48 c1 ea 03 83 e1 07 <42> 0f b6 14 32 38 ca 7f 08 84 d2 0f 85 06 10 00 00 48 89 d8 48 89 RSP: 0018:ffffc900088bf860 EFLAGS: 00010246 RAX: 0000000000040000 RBX: ffffffff9b9bebc0 RCX: 0000000000000000 RDX: 1ffffffff3ac6000 RSI: ffffc90002d82000 RDI: ffffc900088bf9e8 RBP: ffffffff9d630001 R08: 0000000000000000 R09: ffffc900088bf9e8 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000001 R13: ffffffff9d630000 R14: dffffc0000000000 R15: ffffffff9d630000 FS: 00007f63eef63640(0000) GS:ffff88806d000000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: fffffbfff3ac6000 CR3: 0000000029d90005 CR4: 0000000000770ef0 PKRU: 55555554 ================================================================== Link: https://lkml.kernel.org/r/20220907200917.654103-1-lk@c--e.de cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com> cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> cc: "David S. Miller" <davem@davemloft.net> Cc: stable@vger.kernel.org Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Christian A. Ehrhardt <lk@c--e.de> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2022-08-20kprobes: don't call disarm_kprobe() for disabled kprobesKuniyuki Iwashima1-4/+5
The assumption in __disable_kprobe() is wrong, and it could try to disarm an already disarmed kprobe and fire the WARN_ONCE() below. [0] We can easily reproduce this issue. 1. Write 0 to /sys/kernel/debug/kprobes/enabled. # echo 0 > /sys/kernel/debug/kprobes/enabled 2. Run execsnoop. At this time, one kprobe is disabled. # /usr/share/bcc/tools/execsnoop & [1] 2460 PCOMM PID PPID RET ARGS # cat /sys/kernel/debug/kprobes/list ffffffff91345650 r __x64_sys_execve+0x0 [FTRACE] ffffffff91345650 k __x64_sys_execve+0x0 [DISABLED][FTRACE] 3. Write 1 to /sys/kernel/debug/kprobes/enabled, which changes kprobes_all_disarmed to false but does not arm the disabled kprobe. # echo 1 > /sys/kernel/debug/kprobes/enabled # cat /sys/kernel/debug/kprobes/list ffffffff91345650 r __x64_sys_execve+0x0 [FTRACE] ffffffff91345650 k __x64_sys_execve+0x0 [DISABLED][FTRACE] 4. Kill execsnoop, when __disable_kprobe() calls disarm_kprobe() for the disabled kprobe and hits the WARN_ONCE() in __disarm_kprobe_ftrace(). # fg /usr/share/bcc/tools/execsnoop ^C Actually, WARN_ONCE() is fired twice, and __unregister_kprobe_top() misses some cleanups and leaves the aggregated kprobe in the hash table. Then, __unregister_trace_kprobe() initialises tk->rp.kp.list and creates an infinite loop like this. aggregated kprobe.list -> kprobe.list -. ^ | '.__.' In this situation, these commands fall into the infinite loop and result in RCU stall or soft lockup. cat /sys/kernel/debug/kprobes/list : show_kprobe_addr() enters into the infinite loop with RCU. /usr/share/bcc/tools/execsnoop : warn_kprobe_rereg() holds kprobe_mutex, and __get_valid_kprobe() is stuck in the loop. To avoid the issue, make sure we don't call disarm_kprobe() for disabled kprobes. [0] Failed to disarm kprobe-ftrace at __x64_sys_execve+0x0/0x40 (error -2) WARNING: CPU: 6 PID: 2460 at kernel/kprobes.c:1130 __disarm_kprobe_ftrace.isra.19 (kernel/kprobes.c:1129) Modules linked in: ena CPU: 6 PID: 2460 Comm: execsnoop Not tainted 5.19.0+ #28 Hardware name: Amazon EC2 c5.2xlarge/, BIOS 1.0 10/16/2017 RIP: 0010:__disarm_kprobe_ftrace.isra.19 (kernel/kprobes.c:1129) Code: 24 8b 02 eb c1 80 3d c4 83 f2 01 00 75 d4 48 8b 75 00 89 c2 48 c7 c7 90 fa 0f 92 89 04 24 c6 05 ab 83 01 e8 e4 94 f0 ff <0f> 0b 8b 04 24 eb b1 89 c6 48 c7 c7 60 fa 0f 92 89 04 24 e8 cc 94 RSP: 0018:ffff9e6ec154bd98 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffffffff930f7b00 RCX: 0000000000000001 RDX: 0000000080000001 RSI: ffffffff921461c5 RDI: 00000000ffffffff RBP: ffff89c504286da8 R08: 0000000000000000 R09: c0000000fffeffff R10: 0000000000000000 R11: ffff9e6ec154bc28 R12: ffff89c502394e40 R13: ffff89c502394c00 R14: ffff9e6ec154bc00 R15: 0000000000000000 FS: 00007fe800398740(0000) GS:ffff89c812d80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000c00057f010 CR3: 0000000103b54006 CR4: 00000000007706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> __disable_kprobe (kernel/kprobes.c:1716) disable_kprobe (kernel/kprobes.c:2392) __disable_trace_kprobe (kernel/trace/trace_kprobe.c:340) disable_trace_kprobe (kernel/trace/trace_kprobe.c:429) perf_trace_event_unreg.isra.2 (./include/linux/tracepoint.h:93 kernel/trace/trace_event_perf.c:168) perf_kprobe_destroy (kernel/trace/trace_event_perf.c:295) _free_event (kernel/events/core.c:4971) perf_event_release_kernel (kernel/events/core.c:5176) perf_release (kernel/events/core.c:5186) __fput (fs/file_table.c:321) task_work_run (./include/linux/sched.h:2056 (discriminator 1) kernel/task_work.c:179 (discriminator 1)) exit_to_user_mode_prepare (./include/linux/resume_user_mode.h:49 kernel/entry/common.c:169 kernel/entry/common.c:201) syscall_exit_to_user_mode (./arch/x86/include/asm/jump_label.h:55 ./arch/x86/include/asm/nospec-branch.h:384 ./arch/x86/include/asm/entry-common.h:94 kernel/entry/common.c:133 kernel/entry/common.c:296) do_syscall_64 (arch/x86/entry/common.c:87) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) RIP: 0033:0x7fe7ff210654 Code: 15 79 89 20 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb be 0f 1f 00 8b 05 9a cd 20 00 48 63 ff 85 c0 75 11 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 3a f3 c3 48 83 ec 18 48 89 7c 24 08 e8 34 fc RSP: 002b:00007ffdbd1d3538 EFLAGS: 00000246 ORIG_RAX: 0000000000000003 RAX: 0000000000000000 RBX: 0000000000000008 RCX: 00007fe7ff210654 RDX: 0000000000000000 RSI: 0000000000002401 RDI: 0000000000000008 RBP: 0000000000000000 R08: 94ae31d6fda838a4 R0900007fe8001c9d30 R10: 00007ffdbd1d34b0 R11: 0000000000000246 R12: 00007ffdbd1d3600 R13: 0000000000000000 R14: fffffffffffffffc R15: 00007ffdbd1d3560 </TASK> Link: https://lkml.kernel.org/r/20220813020509.90805-1-kuniyu@amazon.com Fixes: 69d54b916d83 ("kprobes: makes kprobes/enabled works correctly for optimized kprobes.") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reported-by: Ayushman Dutta <ayudutta@amazon.com> Cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Cc: Kuniyuki Iwashima <kuniyu@amazon.com> Cc: Kuniyuki Iwashima <kuni1840@gmail.com> Cc: Ayushman Dutta <ayudutta@amazon.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-02kprobes: Forbid probing on trampoline and BPF code areasChen Zhongjin1-1/+2
kernel_text_address() treats ftrace_trampoline, kprobe_insn_slot and bpf_text_address as valid kprobe addresses - which is not ideal. These text areas are removable and changeable without any notification to kprobes, and probing on them can trigger unexpected behavior: https://lkml.org/lkml/2022/7/26/1148 Considering that jump_label and static_call text are already forbiden to probe, kernel_text_address() should be replaced with core_kernel_text() and is_module_text_address() to check other text areas which are unsafe to kprobe. [ mingo: Rewrote the changelog. ] Fixes: 5b485629ba0d ("kprobes, extable: Identify kprobes trampolines as kernel text area") Fixes: 74451e66d516 ("bpf: make jited programs visible in traces") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Link: https://lore.kernel.org/r/20220801033719.228248-1-chenzhongjin@huawei.com
2022-05-29Merge tag 'trace-v5.19' of ↵Linus Torvalds1-73/+71
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing updates from Steven Rostedt: "The majority of the changes are for fixes and clean ups. Notable changes: - Rework trace event triggers code to be easier to interact with. - Support for embedding bootconfig with the kernel (as suppose to having it embedded in initram). This is useful for embedded boards without initram disks. - Speed up boot by parallelizing the creation of tracefs files. - Allow absolute ring buffer timestamps handle timestamps that use more than 59 bits. - Added new tracing clock "TAI" (International Atomic Time) - Have weak functions show up in available_filter_function list as: __ftrace_invalid_address___<invalid-offset> instead of using the name of the function before it" * tag 'trace-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (52 commits) ftrace: Add FTRACE_MCOUNT_MAX_OFFSET to avoid adding weak function tracing: Fix comments for event_trigger_separate_filter() x86/traceponit: Fix comment about irq vector tracepoints x86,tracing: Remove unused headers ftrace: Clean up hash direct_functions on register failures tracing: Fix comments of create_filter() tracing: Disable kcov on trace_preemptirq.c tracing: Initialize integer variable to prevent garbage return value ftrace: Fix typo in comment ftrace: Remove return value of ftrace_arch_modify_*() tracing: Cleanup code by removing init "char *name" tracing: Change "char *" string form to "char []" tracing/timerlat: Do not wakeup the thread if the trace stops at the IRQ tracing/timerlat: Print stacktrace in the IRQ handler if needed tracing/timerlat: Notify IRQ new max latency only if stop tracing is set kprobes: Fix build errors with CONFIG_KRETPROBES=n tracing: Fix return value of trace_pid_write() tracing: Fix potential double free in create_var_ref() tracing: Use strim() to remove whitespace instead of doing it manually ftrace: Deal with error return code of the ftrace_process_locs() function ...
2022-05-26kprobes: Fix build errors with CONFIG_KRETPROBES=nMasami Hiramatsu1-73/+71
Max Filippov reported: When building kernel with CONFIG_KRETPROBES=n kernel/kprobes.c compilation fails with the following messages: kernel/kprobes.c: In function ‘recycle_rp_inst’: kernel/kprobes.c:1273:32: error: implicit declaration of function ‘get_kretprobe’ kernel/kprobes.c: In function ‘kprobe_flush_task’: kernel/kprobes.c:1299:35: error: ‘struct task_struct’ has no member named ‘kretprobe_instances’ This came from the commit d741bf41d7c7 ("kprobes: Remove kretprobe hash") which introduced get_kretprobe() and kretprobe_instances member in task_struct when CONFIG_KRETPROBES=y, but did not make recycle_rp_inst() and kprobe_flush_task() depending on CONFIG_KRETPORBES. Since those functions are only used for kretprobe, move those functions into #ifdef CONFIG_KRETPROBE area. Link: https://lkml.kernel.org/r/165163539094.74407.3838114721073251225.stgit@devnote2 Reported-by: Max Filippov <jcmvbkbc@gmail.com> Fixes: d741bf41d7c7 ("kprobes: Remove kretprobe hash") Cc: "Naveen N . Rao" <naveen.n.rao@linux.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: "David S . Miller" <davem@davemloft.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Tested-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2022-04-26kprobes: Fix KRETPROBES when CONFIG_KRETPROBE_ON_RETHOOK is setAdam Zabrocki1-1/+1
The recent kernel change in 73f9b911faa7 ("kprobes: Use rethook for kretprobe if possible"), introduced a potential NULL pointer dereference bug in the KRETPROBE mechanism. The official Kprobes documentation defines that "Any or all handlers can be NULL". Unfortunately, there is a missing return handler verification to fulfill these requirements and can result in a NULL pointer dereference bug. This patch adds such verification in kretprobe_rethook_handler() function. Fixes: 73f9b911faa7 ("kprobes: Use rethook for kretprobe if possible") Signed-off-by: Adam Zabrocki <pi3@pi3.com.pl> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com> Cc: Anil S. Keshavamurthy <anil.s.keshavamurthy@intel.com> Link: https://lore.kernel.org/bpf/20220422164027.GA7862@pi3.com.pl
2022-03-28kprobes: Use rethook for kretprobe if possibleMasami Hiramatsu1-20/+104
Use rethook for kretprobe function return hooking if the arch sets CONFIG_HAVE_RETHOOK=y. In this case, CONFIG_KRETPROBE_ON_RETHOOK is set to 'y' automatically, and the kretprobe internal data fields switches to use rethook. If not, it continues to use kretprobe specific function return hooks. Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/164826162556.2455864.12255833167233452047.stgit@devnote2
2022-03-15x86/ibt,kprobes: Cure sym+0 equals fentry woesPeter Zijlstra1-14/+52
In order to allow kprobes to skip the ENDBR instructions at sym+0 for X86_KERNEL_IBT builds, change _kprobe_addr() to take an architecture callback to inspect the function at hand and modify the offset if needed. This streamlines the existing interface to cover more cases and require less hooks. Once PowerPC gets fully converted there will only be the one arch hook. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Link: https://lore.kernel.org/r/20220308154318.405947704@infradead.org
2022-03-15x86/ibt,ftrace: Search for __fentry__ locationPeter Zijlstra1-6/+2
Currently a lot of ftrace code assumes __fentry__ is at sym+0. However with Intel IBT enabled the first instruction of a function will most likely be ENDBR. Change ftrace_location() to not only return the __fentry__ location when called for the __fentry__ location, but also when called for the sym+0 location. Then audit/update all callsites of this function to consistently use these new semantics. Suggested-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Link: https://lore.kernel.org/r/20220308154318.227581603@infradead.org
2022-01-22kprobe: move sysctl_kprobes_optimization to kprobes.cXiaoming Ni1-4/+26
kernel/sysctl.c is a kitchen sink where everyone leaves their dirty dishes, this makes it very difficult to maintain. To help with this maintenance let's start by moving sysctls to places where they actually belong. The proc sysctl maintainers do not want to know what sysctl knobs you wish to add for your own piece of code, we just care about the core logic. Move sysctl_kprobes_optimization from kernel/sysctl.c to kernel/kprobes.c. Use register_sysctl() to register the sysctl interface. [mcgrof@kernel.org: fix compile issue when CONFIG_OPTPROBES is disabled] Link: https://lkml.kernel.org/r/20211129211943.640266-7-mcgrof@kernel.org Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: Antti Palosaari <crope@iki.fi> Cc: Christian Brauner <christian.brauner@ubuntu.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Eric Biggers <ebiggers@google.com> Cc: Iurii Zaikin <yzaikin@google.com> Cc: Kees Cook <keescook@chromium.org> Cc: Lukas Middendorf <kernel@tuxforce.de> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com> Cc: Stephen Kitt <steve@sk2.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-12-01kprobes: Limit max data_size of the kretprobe instancesMasami Hiramatsu1-0/+3
The 'kprobe::data_size' is unsigned, thus it can not be negative. But if user sets it enough big number (e.g. (size_t)-8), the result of 'data_size + sizeof(struct kretprobe_instance)' becomes smaller than sizeof(struct kretprobe_instance) or zero. In result, the kretprobe_instance are allocated without enough memory, and kretprobe accesses outside of allocated memory. To avoid this issue, introduce a max limitation of the kretprobe::data_size. 4KB per instance should be OK. Link: https://lkml.kernel.org/r/163836995040.432120.10322772773821182925.stgit@devnote2 Cc: stable@vger.kernel.org Fixes: f47cd9b553aa ("kprobes: kretprobe user entry-handler") Reported-by: zhangyue <zhangyue1@kylinos.cn> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-11-01Merge tag 'trace-v5.16' of ↵Linus Torvalds1-227/+280
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing updates from Steven Rostedt: - kprobes: Restructured stack unwinder to show properly on x86 when a stack dump happens from a kretprobe callback. - Fix to bootconfig parsing - Have tracefs allow owner and group permissions by default (only denying others). There's been pressure to allow non root to tracefs in a controlled fashion, and using groups is probably the safest. - Bootconfig memory managament updates. - Bootconfig clean up to have the tools directory be less dependent on changes in the kernel tree. - Allow perf to be traced by function tracer. - Rewrite of function graph tracer to be a callback from the function tracer instead of having its own trampoline (this change will happen on an arch by arch basis, and currently only x86_64 implements it). - Allow multiple direct trampolines (bpf hooks to functions) be batched together in one synchronization. - Allow histogram triggers to add variables that can perform calculations against the event's fields. - Use the linker to determine architecture callbacks from the ftrace trampoline to allow for proper parameter prototypes and prevent warnings from the compiler. - Extend histogram triggers to key off of variables. - Have trace recursion use bit magic to determine preempt context over if branches. - Have trace recursion disable preemption as all use cases do anyway. - Added testing for verification of tracing utilities. - Various small clean ups and fixes. * tag 'trace-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (101 commits) tracing/histogram: Fix semicolon.cocci warnings tracing/histogram: Fix documentation inline emphasis warning tracing: Increase PERF_MAX_TRACE_SIZE to handle Sentinel1 and docker together tracing: Show size of requested perf buffer bootconfig: Initialize ret in xbc_parse_tree() ftrace: do CPU checking after preemption disabled ftrace: disable preemption when recursion locked tracing/histogram: Document expression arithmetic and constants tracing/histogram: Optimize division by a power of 2 tracing/histogram: Covert expr to const if both operands are constants tracing/histogram: Simplify handling of .sym-offset in expressions tracing: Fix operator precedence for hist triggers expression tracing: Add division and multiplication support for hist triggers tracing: Add support for creating hist trigger variables from literal selftests/ftrace: Stop tracing while reading the trace file by default MAINTAINERS: Update KPROBES and TRACING entries test_kprobes: Move it from kernel/ to lib/ docs, kprobes: Remove invalid URL and add new reference samples/kretprobes: Fix return value if register_kretprobe() failed lib/bootconfig: Fix the xbc_get_info kerneldoc ...
2021-10-21kprobes: convert tests to kunitSven Schnelle1-3/+0
This converts the kprobes testcases to use the kunit framework. It adds a dependency on CONFIG_KUNIT, and the output will change to TAP: TAP version 14 1..1 # Subtest: kprobes_test 1..4 random: crng init done ok 1 - test_kprobe ok 2 - test_kprobes ok 3 - test_kretprobe ok 4 - test_kretprobes ok 1 - kprobes_test Note that the kprobes testcases are no longer run immediately after kprobes initialization, but as a late initcall when kunit is initialized. kprobes itself is initialized with an early initcall, so the order is still correct. Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-10-05sched: Move kprobes cleanup out of finish_task_switch()Thomas Gleixner1-4/+4
Doing cleanups in the tail of schedule() is a latency punishment for the incoming task. The point of invoking kprobes_task_flush() for a dead task is that the instances are returned and cannot leak when __schedule() is kprobed. Move it into the delayed cleanup. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20210928122411.537994026@linutronix.de
2021-09-30x86/kprobes: Fixup return address in generic trampoline handlerMasami Hiramatsu1-0/+11
In x86, the fake return address on the stack saved by __kretprobe_trampoline() will be replaced with the real return address after returning from trampoline_handler(). Before fixing the return address, the real return address can be found in the 'current->kretprobe_instances'. However, since there is a window between updating the 'current->kretprobe_instances' and fixing the address on the stack, if an interrupt happens at that timing and the interrupt handler does stacktrace, it may fail to unwind because it can not get the correct return address from 'current->kretprobe_instances'. This will eliminate that window by fixing the return address right before updating 'current->kretprobe_instances'. Link: https://lkml.kernel.org/r/163163057094.489837.9044470370440745866.stgit@devnote2 Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Tested-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: Enable stacktrace from pt_regs in kretprobe handlerMasami Hiramatsu1-0/+7
Since the ORC unwinder from pt_regs requires setting up regs->ip correctly, set the correct return address to the regs->ip before calling user kretprobe handler. This allows the kretrprobe handler to trace stack from the kretprobe's pt_regs by stack_trace_save_regs() (eBPF will do this), instead of stack tracing from the handler context by stack_trace_save() (ftrace will do this). Link: https://lkml.kernel.org/r/163163053237.489837.4272653874525136832.stgit@devnote2 Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Tested-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: Add kretprobe_find_ret_addr() for searching return addressMasami Hiramatsu1-26/+83
Introduce kretprobe_find_ret_addr() and is_kretprobe_trampoline(). These APIs will be used by the ORC stack unwinder and ftrace, so that they can check whether the given address points kretprobe trampoline code and query the correct return address in that case. Link: https://lkml.kernel.org/r/163163046461.489837.1044778356430293962.stgit@devnote2 Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Tested-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: treewide: Remove trampoline_address from kretprobe_trampoline_handler()Masami Hiramatsu1-2/+1
The __kretprobe_trampoline_handler() callback, called from low level arch kprobes methods, has the 'trampoline_address' parameter, which is entirely superfluous as it basically just replicates: dereference_kernel_function_descriptor(kretprobe_trampoline) In fact we had bugs in arch code where it wasn't replicated correctly. So remove this superfluous parameter and use kretprobe_trampoline_addr() instead. Link: https://lkml.kernel.org/r/163163044546.489837.13505751885476015002.stgit@devnote2 Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Tested-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: treewide: Replace arch_deref_entry_point() with ↵Masami Hiramatsu1-6/+1
dereference_symbol_descriptor() ~15 years ago kprobes grew the 'arch_deref_entry_point()' __weak function: 3d7e33825d87: ("jprobes: make jprobes a little safer for users") But this is just open-coded dereference_symbol_descriptor() in essence, and its obscure nature was causing bugs. Just use the real thing and remove arch_deref_entry_point(). Link: https://lkml.kernel.org/r/163163043630.489837.7924988885652708696.stgit@devnote2 Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Tested-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: Use bool type for functions which returns boolean valueMasami Hiramatsu1-13/+13
Use the 'bool' type instead of 'int' for the functions which returns a boolean value, because this makes clear that those functions don't return any error code. Link: https://lkml.kernel.org/r/163163041649.489837.17311187321419747536.stgit@devnote2 Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: treewide: Use 'kprobe_opcode_t *' for the code address in ↵Masami Hiramatsu1-5/+5
get_optimized_kprobe() Since get_optimized_kprobe() is only used inside kprobes, it doesn't need to use 'unsigned long' type for 'addr' parameter. Make it use 'kprobe_opcode_t *' for the 'addr' parameter and subsequent call of arch_within_optimized_kprobe() also should use 'kprobe_opcode_t *'. Note that MAX_OPTIMIZED_LENGTH and RELATIVEJUMP_SIZE are defined by byte-size, but the size of 'kprobe_opcode_t' depends on the architecture. Therefore, we must be careful when calculating addresses using those macros. Link: https://lkml.kernel.org/r/163163040680.489837.12133032364499833736.stgit@devnote2 Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: Add assertions for required lockMasami Hiramatsu1-7/+12
Add assertions for required locks instead of comment it so that the lockdep can inspect locks automatically. Link: https://lkml.kernel.org/r/163163039572.489837.18011973177537476885.stgit@devnote2 Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: Fix coding style issuesMasami Hiramatsu1-114/+122
Fix coding style issues reported by checkpatch.pl and update comments to quote variable names and add "()" to function name. One TODO comment in __disarm_kprobe() is removed because it has been done by following commit. Link: https://lkml.kernel.org/r/163163037468.489837.4282347782492003960.stgit@devnote2 Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: treewide: Cleanup the error messages for kprobesMasami Hiramatsu1-20/+16
This clean up the error/notification messages in kprobes related code. Basically this defines 'pr_fmt()' macros for each files and update the messages which describes - what happened, - what is the kernel going to do or not do, - is the kernel fine, - what can the user do about it. Also, if the message is not needed (e.g. the function returns unique error code, or other error message is already shown.) remove it, and replace the message with WARN_*() macros if suitable. Link: https://lkml.kernel.org/r/163163036568.489837.14085396178727185469.stgit@devnote2 Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: Make arch_check_ftrace_location staticPunit Agrawal1-2/+2
arch_check_ftrace_location() was introduced as a weak function in commit f7f242ff004499 ("kprobes: introduce weak arch_check_ftrace_location() helper function") to allow architectures to handle kprobes call site on their own. Recently, the only architecture (csky) to implement arch_check_ftrace_location() was migrated to using the common version. As a result, further cleanup the code to drop the weak attribute and rename the function to remove the architecture specific implementation. Link: https://lkml.kernel.org/r/163163035673.489837.2367816318195254104.stgit@devnote2 Signed-off-by: Punit Agrawal <punitagrawal@gmail.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobe: Simplify prepare_kprobe() by dropping redundant versionPunit Agrawal1-14/+9
The function prepare_kprobe() is called during kprobe registration and is responsible for ensuring any architecture related preparation for the kprobe is done before returning. One of two versions of prepare_kprobe() is chosen depending on the availability of KPROBE_ON_FTRACE in the kernel configuration. Simplify the code by dropping the version when KPROBE_ON_FTRACE is not selected - instead relying on kprobe_ftrace() to return false when KPROBE_ON_FTRACE is not set. No functional change. Link: https://lkml.kernel.org/r/163163033696.489837.9264661820279300788.stgit@devnote2 Signed-off-by: Punit Agrawal <punitagrawal@gmail.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: Use helper to parse boolean input from userspacePunit Agrawal1-22/+6
The "enabled" file provides a debugfs interface to arm / disarm kprobes in the kernel. In order to parse the buffer containing the values written from userspace, the callback manually parses the user input to convert it to a boolean value. As taking a string value from userspace and converting it to boolean is a common operation, a helper kstrtobool_from_user() is already available in the kernel. Update the callback to use the common helper to parse the write buffer from userspace. Link: https://lkml.kernel.org/r/163163032637.489837.10678039554832855327.stgit@devnote2 Signed-off-by: Punit Agrawal <punitagrawal@gmail.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-09-30kprobes: Do not use local variable when creating debugfs filePunit Agrawal1-2/+1
debugfs_create_file() takes a pointer argument that can be used during file operation callbacks (accessible via i_private in the inode structure). An obvious requirement is for the pointer to refer to valid memory when used. When creating the debugfs file to dynamically enable / disable kprobes, a pointer to local variable is passed to debugfs_create_file(); which will go out of scope when the init function returns. The reason this hasn't triggered random memory corruption is because the pointer is not accessed during the debugfs file callbacks. Since the enabled state is managed by the kprobes_all_disabled global variable, the local variable is not needed. Fix the incorrect (and unnecessary) usage of local variable during debugfs_file_create() by passing NULL instead. Link: https://lkml.kernel.org/r/163163031686.489837.4476867635937014973.stgit@devnote2 Fixes: bf8f6e5b3e51 ("Kprobes: The ON/OFF knob thru debugfs") Signed-off-by: Punit Agrawal <punitagrawal@gmail.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-07-11Merge tag 'locking-urgent-2021-07-11' of ↵Linus Torvalds1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull locking fixes from Ingo Molnar: - Fix a Sparc crash - Fix a number of objtool warnings - Fix /proc/lockdep output on certain configs - Restore a kprobes fail-safe * tag 'locking-urgent-2021-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: locking/atomic: sparc: Fix arch_cmpxchg64_local() kprobe/static_call: Restore missing static_call_text_reserved() static_call: Fix static_call_text_reserved() vs __init jump_label: Fix jump_label_text_reserved() vs __init locking/lockdep: Fix meaningless /proc/lockdep output of lock classes on !CONFIG_PROVE_LOCKING
2021-07-05kprobe/static_call: Restore missing static_call_text_reserved()Peter Zijlstra1-0/+2
Restore two hunks from commit: 6333e8f73b83 ("static_call: Avoid kprobes on inline static_call()s") that went walkabout in a Git merge commit. Fixes: 76d4acf22b48 ("Merge tag 'perf-kprobes-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip") Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Link: https://lore.kernel.org/r/20210628113045.167127609@infradead.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
2021-07-02Merge tag 'powerpc-5.14-1' of ↵Linus Torvalds1-2/+12
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc updates from Michael Ellerman: - A big series refactoring parts of our KVM code, and converting some to C. - Support for ARCH_HAS_SET_MEMORY, and ARCH_HAS_STRICT_MODULE_RWX on some CPUs. - Support for the Microwatt soft-core. - Optimisations to our interrupt return path on 64-bit. - Support for userspace access to the NX GZIP accelerator on PowerVM on Power10. - Enable KUAP and KUEP by default on 32-bit Book3S CPUs. - Other smaller features, fixes & cleanups. Thanks to: Andy Shevchenko, Aneesh Kumar K.V, Arnd Bergmann, Athira Rajeev, Baokun Li, Benjamin Herrenschmidt, Bharata B Rao, Christophe Leroy, Daniel Axtens, Daniel Henrique Barboza, Finn Thain, Geoff Levand, Haren Myneni, Jason Wang, Jiapeng Chong, Joel Stanley, Jordan Niethe, Kajol Jain, Nathan Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers, Paul Mackerras, Russell Currey, Sathvika Vasireddy, Shaokun Zhang, Stephen Rothwell, Sudeep Holla, Suraj Jitindar Singh, Tom Rix, Vaibhav Jain, YueHaibing, Zhang Jianhua, and Zhen Lei. * tag 'powerpc-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (218 commits) powerpc: Only build restart_table.c for 64s powerpc/64s: move ret_from_fork etc above __end_soft_masked powerpc/64s/interrupt: clean up interrupt return labels powerpc/64/interrupt: add missing kprobe annotations on interrupt exit symbols powerpc/64: enable MSR[EE] in irq replay pt_regs powerpc/64s/interrupt: preserve regs->softe for NMI interrupts powerpc/64s: add a table of implicit soft-masked addresses powerpc/64e: remove implicit soft-masking and interrupt exit restart logic powerpc/64e: fix CONFIG_RELOCATABLE build warnings powerpc/64s: fix hash page fault interrupt handler powerpc/4xx: Fix setup_kuep() on SMP powerpc/32s: Fix setup_{kuap/kuep}() on SMP powerpc/interrupt: Use names in check_return_regs_valid() powerpc/interrupt: Also use exit_must_hard_disable() on PPC32 powerpc/sysfs: Replace sizeof(arr)/sizeof(arr[0]) with ARRAY_SIZE powerpc/ptrace: Refactor regs_set_return_{msr/ip} powerpc/ptrace: Move set_return_regs_changed() before regs_set_return_{msr/ip} powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi() powerpc/pseries/vas: Include irqdomain.h powerpc: mark local variables around longjmp as volatile ...
2021-07-02Merge branch 'akpm' (patches from Andrew)Linus Torvalds1-1/+1
Merge more updates from Andrew Morton: "190 patches. Subsystems affected by this patch series: mm (hugetlb, userfaultfd, vmscan, kconfig, proc, z3fold, zbud, ras, mempolicy, memblock, migration, thp, nommu, kconfig, madvise, memory-hotplug, zswap, zsmalloc, zram, cleanups, kfence, and hmm), procfs, sysctl, misc, core-kernel, lib, lz4, checkpatch, init, kprobes, nilfs2, hfs, signals, exec, kcov, selftests, compress/decompress, and ipc" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits) ipc/util.c: use binary search for max_idx ipc/sem.c: use READ_ONCE()/WRITE_ONCE() for use_global_lock ipc: use kmalloc for msg_queue and shmid_kernel ipc sem: use kvmalloc for sem_undo allocation lib/decompressors: remove set but not used variabled 'level' selftests/vm/pkeys: exercise x86 XSAVE init state selftests/vm/pkeys: refill shadow register after implicit kernel write selftests/vm/pkeys: handle negative sys_pkey_alloc() return code selftests/vm/pkeys: fix alloc_random_pkey() to make it really, really random kcov: add __no_sanitize_coverage to fix noinstr for all architectures exec: remove checks in __register_bimfmt() x86: signal: don't do sas_ss_reset() until we are certain that sigframe won't be abandoned hfsplus: report create_date to kstat.btime hfsplus: remove unnecessary oom message nilfs2: remove redundant continue statement in a while-loop kprobes: remove duplicated strong free_insn_page in x86 and s390 init: print out unknown kernel parameters checkpatch: do not complain about positive return values starting with EPOLL checkpatch: improve the indented label test checkpatch: scripts/spdxcheck.py now requires python3 ...
2021-07-01kprobes: remove duplicated strong free_insn_page in x86 and s390Barry Song1-1/+1
free_insn_page() in x86 and s390 is same with the common weak function in kernel/kprobes.c. Plus, the comment "Recover page to RW mode before releasing it" in x86 seems insensible to be there since resetting mapping is done by common code in vfree() of module_memfree(). So drop these two duplicated strong functions and related comment, then mark the common one in kernel/kprobes.c strong. Link: https://lkml.kernel.org/r/20210608065736.32656-1-song.bao.hua@hisilicon.com Signed-off-by: Barry Song <song.bao.hua@hisilicon.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Heiko Carstens <hca@linux.ibm.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Qi Liu <liuqi115@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-01kprobes: Remove kprobe::fault_handlerPeter Zijlstra1-19/+0
The reason for kprobe::fault_handler(), as given by their comment: * We come here because instructions in the pre/post * handler caused the page_fault, this could happen * if handler tries to access user space by * copy_from_user(), get_user() etc. Let the * user-specified handler try to fix it first. Is just plain bad. Those other handlers are ran from non-preemptible context and had better use _nofault() functions. Also, there is no upstream usage of this. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Link: https://lore.kernel.org/r/20210525073213.561116662@infradead.org
2021-05-23kprobes: Allow architectures to override optinsn page allocationChristophe Leroy1-2/+12
Some architectures like powerpc require a non standard allocation of optinsn page, because module pages are too far from the kernel for direct branches. Define weak alloc_optinsn_page() and free_optinsn_page(), that fall back on alloc_insn_page() and free_insn_page() when not overridden by the architecture. Suggested-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/40a43d6df1fdf41ade36e9a46e60a4df774ca9f6.1620896780.git.christophe.leroy@csgroup.eu
2021-02-19kprobes: Fix to delay the kprobes jump optimizationMasami Hiramatsu1-10/+21
Commit 36dadef23fcc ("kprobes: Init kprobes in early_initcall") moved the kprobe setup in early_initcall(), which includes kprobe jump optimization. The kprobes jump optimizer involves synchronize_rcu_tasks() which depends on the ksoftirqd and rcu_spawn_tasks_*(). However, since those are setup in core_initcall(), kprobes jump optimizer can not run at the early_initcall(). To avoid this issue, make the kprobe optimization disabled in the early_initcall() and enables it in subsys_initcall(). Note that non-optimized kprobes is still available after early_initcall(). Only jump optimization is delayed. Link: https://lkml.kernel.org/r/161365856280.719838.12423085451287256713.stgit@devnote2 Fixes: 36dadef23fcc ("kprobes: Init kprobes in early_initcall") Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: RCU <rcu@vger.kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Daniel Axtens <dja@axtens.net> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Neeraj Upadhyay <neeraju@codeaurora.org> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Michal Hocko <mhocko@suse.com> Cc: "Theodore Y . Ts'o" <tytso@mit.edu> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: stable@vger.kernel.org Reported-by: Paul E. McKenney <paulmck@kernel.org> Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reported-by: Uladzislau Rezki <urezki@gmail.com> Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-02-09kprobes: Warn if the kprobe is reregisteredMasami Hiramatsu1-5/+8
Warn if the kprobe is reregistered, since there must be a software bug (actively used resource must not be re-registered) and caller must be fixed. Link: https://lkml.kernel.org/r/161236436734.194052.4058506306336814476.stgit@devnote2 Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Ananth N Mavinakayanahalli <ananth@linux.ibm.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-01-29kretprobe: Avoid re-registration of the same kretprobe earlierWang ShaoBo1-0/+4
Our system encountered a re-init error when re-registering same kretprobe, where the kretprobe_instance in rp->free_instances is illegally accessed after re-init. Implementation to avoid re-registration has been introduced for kprobe before, but lags for register_kretprobe(). We must check if kprobe has been re-registered before re-initializing kretprobe, otherwise it will destroy the data struct of kretprobe registered, which can lead to memory leak, system crash, also some unexpected behaviors. We use check_kprobe_rereg() to check if kprobe has been re-registered before running register_kretprobe()'s body, for giving a warning message and terminate registration process. Link: https://lkml.kernel.org/r/20210128124427.2031088-1-bobo.shaobowang@huawei.com Cc: stable@vger.kernel.org Fixes: 1f0ab40976460 ("kprobes: Prevent re-registration of the same kprobe") [ The above commit should have been done for kretprobes too ] Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Ananth N Mavinakayanahalli <ananth@linux.ibm.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Signed-off-by: Cheng Jian <cj.chengjian@huawei.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-01-29tracing/kprobe: Fix to support kretprobe events on unloaded modulesMasami Hiramatsu1-9/+25
Fix kprobe_on_func_entry() returns error code instead of false so that register_kretprobe() can return an appropriate error code. append_trace_kprobe() expects the kprobe registration returns -ENOENT when the target symbol is not found, and it checks whether the target module is unloaded or not. If the target module doesn't exist, it defers to probe the target symbol until the module is loaded. However, since register_kretprobe() returns -EINVAL instead of -ENOENT in that case, it always fail on putting the kretprobe event on unloaded modules. e.g. Kprobe event: /sys/kernel/debug/tracing # echo p xfs:xfs_end_io >> kprobe_events [ 16.515574] trace_kprobe: This probe might be able to register after target module is loaded. Continue. Kretprobe event: (p -> r) /sys/kernel/debug/tracing # echo r xfs:xfs_end_io >> kprobe_events sh: write error: Invalid argument /sys/kernel/debug/tracing # cat error_log [ 41.122514] trace_kprobe: error: Failed to register probe event Command: r xfs:xfs_end_io ^ To fix this bug, change kprobe_on_func_entry() to detect symbol lookup failure and return -ENOENT in that case. Otherwise it returns -EINVAL or 0 (succeeded, given address is on the entry). Link: https://lkml.kernel.org/r/161176187132.1067016.8118042342894378981.stgit@devnote2 Cc: stable@vger.kernel.org Fixes: 59158ec4aef7 ("tracing/kprobes: Check the probe on unloaded module correctly") Reported-by: Jianlin Lv <Jianlin.Lv@arm.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2020-11-07Merge branch 'linus' into perf/kprobesIngo Molnar1-1/+23
Merge recent kprobes updates into perf/kprobes that came from -mm. Signed-off-by: Ingo Molnar <mingo@kernel.org>
2020-10-12kprobes: Replace rp->free_instance with freelistPeter Zijlstra1-32/+24
Gets rid of rp->lock, and as a result kretprobes are now fully lockless. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/159870623583.1229682.17472357584134058687.stgit@devnote2
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-21 11:29:13 +0000