| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit b03e7495a862 ("PCI: Set PCI-E Max Payload Size on fabric")
introduced a potential NULL pointer dereference in calls to
pcie_bus_configure_settings due to attempts to access pci_bus self
variables when the self pointer is NULL.
To correct this, verify that the self pointer in pci_bus is non-NULL
before dereferencing it.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Correct UV2 BAU destination timeout
x86, UV: Correct failed topology memory leak
x86, UV: Remove cpumask_t from the stack
x86, UV: Rename hubmask to pnmask
x86, UV: Correct reset_with_ipi()
x86, UV: Allow for non-consecutive sockets
x86, UV: Inline header file functions
x86, UV: Fix smp_processor_id() use in a preemptable region
x66, UV: Enable 64-bit ACPI MFCG support for SGI UV2 platform
x86, UV: Clean up uv_mmrs.h
|
|
Commit 6e8af08dfa40b747002207d3ce8e8b43a050d99f enables pci=bfsort on
future Dell systems. But the identification string 'Dell System' matches
on already existing whitelist, which do not have SMBIOS type 0xB1,
causing pci=bfsort not being set on existing whitelist.
This patch fixes the regression by moving the type 0xB1 check beyond the
existing whitelist so that existing whitelist is walked before.
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Narendra K <narendra_k@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Aside of the usual motivation for constification, this function has a
history of being abused a hook for interrupt and other fixups so I turned
this function const ages ago in the MIPS code but it should be done
treewide.
Due to function pointer passing in varous places a few other functions
had to be constified as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To: Anton Vorontsov <avorontsov@mvista.com>
To: Chris Metcalf <cmetcalf@tilera.com>
To: Colin Cross <ccross@android.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
To: Eric Miao <eric.y.miao@gmail.com>
To: Erik Gilling <konkers@android.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
To: "H. Peter Anvin" <hpa@zytor.com>
To: Imre Kaloz <kaloz@openwrt.org>
To: Ingo Molnar <mingo@redhat.com>
To: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
To: Jesse Barnes <jbarnes@virtuousgeek.org>
To: Krzysztof Halasa <khc@pm.waw.pl>
To: Lennert Buytenhek <kernel@wantstofly.org>
To: Matt Turner <mattst88@gmail.com>
To: Nicolas Pitre <nico@fluxnic.net>
To: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
To: Richard Henderson <rth@twiddle.net>
To: Russell King <linux@arm.linux.org.uk>
To: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-pci@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Without this change, the majority of the raw PCI config space access
functions silently ignore a non-zero segment argument, which is
certainly wrong.
Apart from pci_direct_conf1, all other non-MMCFG access methods get
used only for non-extended accesses (i.e. assigned to raw_pci_ops
only). Consequently, with the way raw_pci_{read,write}() work, it would
be a coding error to call these functions with a non-zero segment (with
the current call flow this cannot happen afaict).
The access method 1 accessor, as it can be used for extended accesses
(on AMD systems) instead gets checks added for the passed in segment to
be zero. This would be the case when on such a system having multiple
PCI segments (don't know whether any exist in practice) MMCFG for some
reason is not usable, and method 1 gets selected for doing extended
accesses. Rather than accessing the wrong device's config space, the
function will now error out.
v2: Convert BUG_ON() to WARN_ON(), and extend description as per Ingo's
request.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Host bridge windows are top-level resources, so if we find a host bridge
window conflict, it's probably with a hard-coded legacy reservation.
Moving host bridge windows is theoretically possible, but we don't support
it; we just ignore windows with conflicts, and it's not worth making this
a user-visible error.
Reported-and-tested-by: Jools Wills <jools@oxfordinspire.co.uk>
References: https://bugzilla.kernel.org/show_bug.cgi?id=38522
Reported-by: Das <dasfox@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=16497
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
In the past we would only use the function's value if the
returned value was not equal to 'acpi_sci_override_gsi'. Meaning
that the INT_SRV_OVR values for global and source irq were different.
But it is OK to use the function's value even when the global
and source irq are the same.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
In the past (2.6.38) the 'xen_allocate_pirq_gsi' would allocate
an entry in a Linux IRQ -> {XEN_IRQ, type, event, ..} array. All
of that has been removed in 2.6.39 and the Xen IRQ subsystem uses
an linked list that is populated when the call to
'xen_allocate_irq_gsi' (universally done from any of the xen_bind_*
calls) is done. The 'xen_allocate_pirq_gsi' is a NOP and there is
no need for it anymore so lets remove it.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
As the code paths that are guarded by CONFIG_XEN_DOM0 already depend
on CONFIG_ACPI so the extra #ifdef is not required. The earlier
patch that added them in had done its job.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
.. which means we can preset of NR_IRQS_LEGACY interrupts using
the 'acpi_get_override_irq' API before this loop.
This means that we can get the IRQ's polarity (and trigger) from either
the ACPI (or MP); or use the default values. This fixes a bug if we did
not have an IOAPIC we would not been able to preset the IRQ's polarity
if the MP table existed.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Since they are only called once and the rest of the pci_xen_*
functions follow the same pattern of setup.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
.. to cut down on the code duplicity.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Not before .. also that code segment starts looking like the HVM one.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
In the past we would guard those code segments to be dependent
on CONFIG_XEN_DOM0 (which depends on CONFIG_ACPI) so this patch is
not stricly necessary. But the next patch will merge common
HVM and initial domain code and we want to make sure the CONFIG_ACPI
dependency is preserved - as HVM code does not depend on CONFIG_XEN_DOM0.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Update the out-dated comment at the beginning of the file.
Also provide the copyrights of folks who have been contributing
to this code lately.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
The file is hard to read. Move the code around so that
the contents of it follows a uniform format:
- setup GSIs - PV, HVM, and initial domain case
- then MSI/MSI-x setup - PV, HVM and then initial domain case.
- then MSI/MSI-x teardown - same order.
- lastly, the __init functions in PV, HVM, and initial domain order.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Move check for acpi_sci_override_gsi to xen_setup_acpi_sci.
|
|
Previously we would check for acpi_sci_override_gsi == gsi every time
a PCI device was enabled. That works during early bootup, but later
on it could lead to triggering unnecessarily the acpi_gsi_to_irq(..) lookup.
The reason is that acpi_sci_override_gsi was declared in __initdata and
after early bootup could contain bogus values.
This patch moves the check for acpi_sci_override_gsi to the
site where the ACPI SCI is preset.
CC: stable@kernel.org
Reported-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
Tested-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
[http://lists.xensource.com/archives/html/xen-devel/2011-07/msg00154.html]
Suggested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Use the INT_SRC_OVR IRQ (instead of GSI) to preset the ACPI SCI IRQ.
xen/mmu: Fix for linker errors when CONFIG_SMP is not defined.
|
|
In the past we would use the GSI value to preset the ACPI SCI
IRQ which worked great as GSI == IRQ:
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
While that is most often seen, there are some oddities:
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
which means that GSI 20 (or pin 20) is to be overriden for IRQ 9.
Our code that presets the interrupt for ACPI SCI however would
use the GSI 20 instead of IRQ 9 ending up with:
xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=20
xen: acpi sci 20
.. snip..
calling acpi_init+0x0/0xbc @ 1
ACPI: SCI (IRQ9) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20110413/evevent-119)
ACPI: Unable to start the ACPI Interpreter
as the ACPI interpreter made a call to 'acpi_gsi_to_irq' which got nine.
It used that value to request an IRQ (request_irq) and since that was not
present it failed.
The fix is to recognize that for interrupts that are overriden (in our
case we only care about the ACPI SCI) we should use the IRQ number
to present the IRQ instead of the using GSI. End result is that we get:
xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=9 (gsi=9)
xen: acpi sci 9
which fixes the ACPI interpreter failing on startup.
CC: stable@kernel.org
Reported-by: Liwei <xieliwei@gmail.com>
Tested-by: Liwei <xieliwei@gmail.com>
[http://lists.xensource.com/archives/html/xen-devel/2011-06/msg01727.html]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Enable 64-bit ACPI MFCG support for SGI UV2 platform. The check
is similar to the check on UV1. UV2 has a different oem_id
string.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20110602195943.GA27079@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The flags field of struct resource from linux/ioport.h is "unsigned
long". Change the "type" parameter of coalesce_windows() function to
match that field. This fixes the following warning messages when
compiling with "make C=1 W=1 bzImage modules":
arch/x86/pci/acpi.c: In function ‘coalesce_windows’:
arch/x86/pci/acpi.c:198: warning: conversion to ‘long unsigned int’ from ‘int’ may change the sign of the result
arch/x86/pci/acpi.c:203: warning: conversion to ‘long unsigned int’ from ‘int’ may change the sign of the result
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
PCI: Don't use dmi_name_in_vendors in quirk
PCI: remove unused AER functions
PCI/sysfs: move bus cpuaffinity to class dev_attrs
PCI: add rescan to /sys/.../pci_bus/.../
PCI: update bridge resources to get more big ranges when allocating space (again)
KVM: Use pci_store/load_saved_state() around VM device usage
PCI: Add interfaces to store and load the device saved state
PCI: Track the size of each saved capability data area
PCI/e1000e: Add and use pci_disable_link_state_locked()
x86/PCI: derive pcibios_last_bus from ACPI MCFG
PCI: add latency tolerance reporting enable/disable support
PCI: add OBFF enable/disable support
PCI: add ID-based ordering enable/disable support
PCI hotplug: acpiphp: assume device is in state D0 after powering on a slot.
PCI: Set PCIE maxpayload for card during hotplug insertion
PCI/ACPI: Report _OSC control mask returned on failure to get control
x86/PCI: irq and pci_ids patch for Intel Panther Point DeviceIDs
PCI: handle positive error codes
PCI: check pci_vpd_pci22_wait() return
PCI: Use ICH6_GPIO_EN in ich6_lpc_acpi_gpio
...
Fix up trivial conflicts in include/linux/pci_ids.h: commit a6e5e2be4461
moved the intel SMBUS ID definitons to the i2c-i801.c driver.
|
|
On various newer Intel systems the PCI bus(ses) the non-core devices
live on aren't getting announced by ACPI except through the bus range
covered by mmconfig. At least the i7core-edac driver depends on these
devices getting detected.
Mauro, could you check whether with this change the Xeon 55xx hack in
that driver can go away altogether, and with it the bogus exporting of
pcibios_scan_specific_bus()?
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Aristeu Sergio <arozansk@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
If we have CONFIG_XEN and the other parameters to build an
Linux kernel that is non-privileged, the xen_[find|register|unregister]_
device_domain_owner functions should not be compiled. They should
use the nops defined in arch/x86/include/asm/xen/pci.h instead.
This fixes:
arch/x86/pci/xen.c:496: error: redefinition of ‘xen_find_device_domain_owner’
arch/x86/include/asm/xen/pci.h:25: note: previous definition of ‘xen_find_device_domain_owner’ was here
arch/x86/pci/xen.c:510: error: redefinition of ‘xen_register_device_domain_owner’
arch/x86/include/asm/xen/pci.h:29: note: previous definition of ‘xen_register_device_domain_owner’ was here
arch/x86/pci/xen.c:532: error: redefinition of ‘xen_unregister_device_domain_owner’
arch/x86/include/asm/xen/pci.h:34: note: previous definition of ‘xen_unregister_device_domain_owner’ was here
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
|
|
This patch adds the LPC Controller DeviceIDs for the Intel Panther Point PCH.
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Request_region should be used with release_region, not release_resource.
The local variables region and region2 are dropped and the calls to
release_resource are replaced with calls to release_region, using the first
two arguments of the corresponding calls to request_region.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,E;
@@
(
*x = request_region(...)
|
*x = request_mem_region(...)
)
... when != release_region(x)
when != x = E
* release_resource(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We check if there is a domain owner for the PCI device. In case of failure
(meaning no domain has registered for this device) we make DOMID_SELF the owner.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: deal with rebasing on v2.6.37-1]
[v3: deal with rebasing on stable/irq.cleanup]
[v4: deal with rebasing on stable/irq.ween_of_nr_irqs]
[v5: deal with rebasing on v2.6.39-rc3]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Xiantao Zhang <xiantao.zhang@intel.com>
|
|
When the Xen PCI backend is told to enable or disable MSI/MSI-X functions,
the initial domain performs these operations. The initial domain needs
to know which domain (guest) is going to use the PCI device so when it
makes the appropiate hypercall to retrieve the MSI/MSI-X vector it will
also assign the PCI device to the appropiate domain (guest).
This boils down to us needing a mechanism to find, set and unset the domain
id that will be using the device.
[v2: EXPORT_SYMBOL -> EXPORT_SYMBOL_GPL.]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: label: remove #include of ACPI header to avoid warnings
PCI: label: Fix compilation error when CONFIG_ACPI is unset
PCI: pre-allocate additional resources to devices only after successful allocation of essential resources.
PCI: introduce reset_resource()
PCI: data structure agnostic free list function
PCI: refactor io size calculation code
PCI: do not create quirk I/O regions below PCIBIOS_MIN_IO for ICH
PCI hotplug: acpiphp: set current_state to D0 in register_slot
PCI: Export ACPI _DSM provided firmware instance number and string name to sysfs
PCI: add more checking to ICH region quirks
PCI: aer-inject: Override PCIe AER Mask Registers
PCI: fix tlan build when CONFIG_PCI is not enabled
PCI: remove quirk for pre-production systems
PCI: Avoid potential NULL pointer dereference in pci_scan_bridge
PCI/lpc: irq and pci_ids patch for Intel DH89xxCC DeviceIDs
PCI: sysfs: Fix failure path for addition of "vpd" attribute
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Flush TLB if PGD entry is changed in i386 PAE mode
x86, dumpstack: Correct stack dump info when frame pointer is available
x86: Clean up csum-copy_64.S a bit
x86: Fix common misspellings
x86: Fix misspelling and align params
x86: Use PentiumPro-optimized partial_csum() on VIA C7
|
|
They were generated by 'codespell' and then manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: trivial@kernel.org
LKML-Reference: <1300389856-1099-3-git-send-email-lucas.demarchi@profusion.mobi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/irq.fairness' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: events: Remove redundant clear of l2i at end of round-robin loop
xen: events: Make round-robin scan fairer by snapshotting each l2 word once only
xen: events: Clean up round-robin evtchn scan.
xen: events: Make last processed event channel a per-cpu variable.
xen: events: Process event channels notifications in round-robin order.
* 'stable/irq.ween_of_nr_irqs' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: events: Fix compile error if CONFIG_SMP is not defined.
xen: events: correct locking in xen_irq_from_pirq
xen: events: propagate irq allocation failure instead of panicking
xen: events: do not workaround too-small nr_irqs
xen: events: remove use of nr_irqs as upper bound on number of pirqs
xen: events: dynamically allocate irq info structures
xen: events: maintain a list of Xen interrupts
xen: events: push setup of irq<->{evtchn,ipi,virq,pirq} maps into irq_info init functions
xen: events: turn irq_info constructors into initialiser functions
xen: events: use per-cpu variable for cpu_evtchn_mask
xen: events: refactor GSI pirq bindings functions
xen: events: rename restore_cpu_pirqs -> restore_pirqs
xen: events: remove unused public functions
xen: events: fix xen_map_pirq_gsi error return
xen: events: simplify comment
xen: events: separate two unrelated halves of if condition
Fix up trivial conflicts in drivers/xen/events.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (93 commits)
x86, tlb, UV: Do small micro-optimization for native_flush_tlb_others()
x86-64, NUMA: Don't call numa_set_distanc() for all possible node combinations during emulation
x86-64, NUMA: Don't assume phys node 0 is always online in numa_emulation()
x86-64, NUMA: Clean up initmem_init()
x86-64, NUMA: Fix numa_emulation code with node0 without RAM
x86-64, NUMA: Revert NUMA affine page table allocation
x86: Work around old gas bug
x86-64, NUMA: Better explain numa_distance handling
x86-64, NUMA: Fix distance table handling
mm: Move early_node_map[] reverse scan helpers under HAVE_MEMBLOCK
x86-64, NUMA: Fix size of numa_distance array
x86: Rename e820_table_* to pgt_buf_*
bootmem: Move __alloc_memory_core_early() to nobootmem.c
bootmem: Move contig_page_data definition to bootmem.c/nobootmem.c
bootmem: Separate out CONFIG_NO_BOOTMEM code into nobootmem.c
x86-64, NUMA: Seperate out numa_alloc_distance() from numa_set_distance()
x86-64, NUMA: Add proper function comments to global functions
x86-64, NUMA: Move NUMA emulation into numa_emulation.c
x86-64, NUMA: Prepare numa_emulation() for moving NUMA emulation into a separate file
x86-64, NUMA: Do not scan two times for setup_node_bootmem()
...
Fix up conflicts in arch/x86/kernel/smpboot.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/irq.cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: events: remove dom0 specific xen_create_msi_irq
xen: events: use xen_bind_pirq_msi_to_irq from xen_create_msi_irq
xen: events: push set_irq_msi down into xen_create_msi_irq
xen: events: update pirq_to_irq in xen_create_msi_irq
xen: events: refactor xen_create_msi_irq slightly
xen: events: separate MSI PIRQ allocation from PIRQ binding to IRQ
xen: events: assume PHYSDEVOP_get_free_pirq exists
xen: pci: collapse apic_register_gsi_xen_hvm and xen_hvm_register_pirq
xen: events: return irq from xen_allocate_pirq_msi
xen: events: drop XEN_ALLOC_IRQ flag to xen_allocate_pirq_msi
xen: events: do not leak IRQ from xen_allocate_pirq_msi when no pirq available.
xen: pci: only define xen_initdom_setup_msi_irqs if CONFIG_XEN_DOM0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/irq.rework' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/irq: Cleanup up the pirq_to_irq for DomU PV PCI passthrough guests as well.
xen: Use IRQF_FORCE_RESUME
xen/timer: Missing IRQF_NO_SUSPEND in timer code broke suspend.
xen: Fix compile error introduced by "switch to new irq_chip functions"
xen: Switch to new irq_chip functions
xen: Remove stale irq_chip.end
xen: events: do not free legacy IRQs
xen: events: allocate GSIs and dynamic IRQs from separate IRQ ranges.
xen: events: add xen_allocate_irq_{dynamic, gsi} and xen_free_irq
xen:events: move find_unbound_irq inside CONFIG_PCI_MSI
xen: handled remapped IRQs when enabling a pcifront PCI device.
genirq: Add IRQF_FORCE_RESUME
* 'stable/pcifront-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
pci/xen: When free-ing MSI-X/MSI irq->desc also use generic code.
pci/xen: Cleanup: convert int** to int[]
pci/xen: Use xen_allocate_pirq_msi instead of xen_allocate_pirq
xen-pcifront: Sanity check the MSI/MSI-X values
xen-pcifront: don't use flush_scheduled_work()
|
|
Conflicts:
arch/x86/mm/numa_64.c
Merge reason: Resolve the conflict, update the branch to .38.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Setting the pci ops on subsys initcall unconditionally will break
multi platform kernels on anything except ce4100.
Use x86_init.pci.init ops to call this only on real ce4100 platforms.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: sodaville@linutronix.de
LKML-Reference: <20110314093340.GA21026@www.tglx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Following the example set by xen_allocate_pirq_msi and
xen_bind_pirq_msi_to_irq:
xen_allocate_pirq becomes xen_allocate_pirq_gsi and now only allocates
a pirq number and does not bind it.
xen_map_pirq_gsi becomes xen_bind_pirq_gsi_to_irq and binds an
existing pirq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
The function name does not distinguish it from xen_allocate_pirq_msi
(which operates on domU and pvhvm domains rather than dom0).
Hoist domain 0 specific functionality up into the only caller leaving
functionality common to all guest types in xen_bind_pirq_msi_to_irq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Makes the tail end of this function look even more like
xen_bind_pirq_msi_to_irq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Split the binding aspect of xen_allocate_pirq_msi out into a new
xen_bind_pirq_to_irq function.
In xen_hvm_setup_msi_irq when allocating a pirq write the MSI message
to signal the PIRQ as soon as the pirq is obtained. There is no way to
free the pirq back so if the subsequent binding to an IRQ fails we
want to ensure that we will reuse the PIRQ next time rather than leak
it.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
apic_register_gsi_xen_hvm is a tiny wrapper around
xen_hvm_register_pirq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
consistent with other similar functions.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
All callers pass this flag so it is pointless.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Fixes:
CC arch/x86/pci/xen.o
arch/x86/pci/xen.c:183: warning: 'xen_initdom_setup_msi_irqs' defined but not used
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
