| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.2, 3rd round:
- Fix i.MX6 PCIe interrupt routing which gets missed from stacked IRQ
domain conversion. The PCIe wakeup support is currently broken
because of this.
* tag 'imx-fixes-4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6: correct i.MX6 PCIe interrupt routing
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Two fixes for bugs in Exynos power domain error exit path:
1. kfree() of read-only memory (name of power domain returned
by kstrdup_const()),
2. Doubled of_node_put() leading to invalid ref count for OF node.
* tag 'samsung-mach-fixes-4.2' of https://github.com/krzk/linux:
ARM: EXYNOS: fix double of_node_put() on error path
ARM: EXYNOS: Fix potentian kfree() of ro memory
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few trivial omap MMC regression fixes for card voltages where
the syscon areas for PBIAS regulator were missing "simple-bus"
that prevents probing of the children in the mapped region.
This probably was not noticed earlier as the bootloader has
already configured the regulator for the card in the slot.
* tag 'omap-for-v4.2/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7: Fix broken pbias device creation
ARM: dts: OMAP5: Fix broken pbias device creation
ARM: dts: OMAP4: Fix broken pbias device creation
ARM: dts: omap243x: Fix broken pbias device creation
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The PCIe interrupts are also routed through the GPC. This has been
missed from the conversion to stacked IRQ domains as the PCIe
controller uses an explicit interrupt map and thus doesn't inherit
the SoC global interrupt parent.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Cc: <stable@vger.kernel.org> # 4.1
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The "cpus" node cannot be inside the "soc" node, while this
works for the CoreSight blocks, the early boot code will look
for "cpus" directly under the root node, so this is a hard
convention. So move the CPU nodes.
Augment the "reg" property to match what is actually in the
hardware: 0x300 and 0x301 respectively.
Then add an SMP enablement type to be used by the SMP init
code, "ste,dbx500-smp".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
commit <d919501feffa> ("ARM: dts: dra7: add minimal l4 bus
layout with control module support") moved pbias_regulator dt node
from being a child node of ocp to be the child node of
scm_conf. After this device for pbias_regulator is
not created.
Fix it by adding "simple-bus" compatible property to
scm_conf dt node.
Fixes: d919501feffa ("ARM: dts: dra7: add minimal l4 bus
layout with control module support")
Cc: <stable@vger.kernel.org> # v4.1
Suggested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit <ed8509edddeb> ("ARM: dts: omap5: add minimal l4 bus
layout with control module support") moved pbias_regulator dt node
from being a child node of ocp to be the child node of
omap5_padconf_global. After this device for pbias_regulator is
not created.
Fix it by adding "simple-bus" compatible property to
omap5_padconf_global dt node.
Fixes: ed8509edddeb ("ARM: dts: omap5: add minimal l4 bus
layout with control module support")
Cc: <stable@vger.kernel.org> # v4.1
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit <7415b0b4c645> ("ARM: dts: omap4: add minimal l4 bus layout
with control module support") moved pbias_regulator dt node
from being a child node of ocp to be the child node of
omap4_padconf_global. After this device for pbias_regulator
is not created.
Fix it by adding "simple-bus" compatible property to
omap4_padconf_global dt node.
Fixes: 7415b0b4c645 ("ARM: dts: omap4: add minimal l4 bus layout
with control module support")
Cc: <stable@vger.kernel.org> # v4.1
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit <72b10ac00eb1> ("ARM: dts: omap24xx: add minimal l4 bus
layout with control module support") moved pbias_regulator dt node
from being a child node of ocp to be the child node of
scm_conf. After this device for pbias_regulator is
not created.
Fix it by adding "simple-bus" compatible property to
scm_conf dt node.
Fixes: 72b10ac00eb1 ("ARM: dts: omap24xx: add minimal l4 bus
layout with control module support")
Cc: <stable@vger.kernel.org> # v4.1
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
All of the keystone devices have a separate register to hold post
divider value for main pll clock. Currently the fixed-postdiv
value used for k2hk/l/e SoCs works by sheer luck as u-boot happens to
use a value of 2 for this. Now that we have fixed this in the pll
clock driver change the dt bindings for the same.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The change removes the second of_node_put(), if
for_each_compatible_node() body execution is not terminated. This
prevents from object refcounter overflow over zero in OF_DYNAMIC
build.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
The change fixes a bug introduced by 2be2a3ff42a5, memory allocated
by kstrdup_const() must be always deallocated with kfree_const(),
otherwise there is a risk of kfree'ing ro memory in power domain error
exit path.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: <stable@vger.kernel.org>
Fixes: 2be2a3ff42a5 ("ARM: EXYNOS: register power domain driver from core_initcall")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.2, 2nd round:
- Add the required second clock for i.MX35 FlexCAN in device tree,
so that the device can be probed by kernel successfully.
* tag 'imx-fixes-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: i.MX35: Fix can support.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The UART0 is not used on these boards, yet active and blocking
other use. Fix this by disabling UART0 and setting port aliases
to maintain port enumeration to userspace.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
Merge "ARM: OMAP2+: hwmod fixes for v4.2-rc" from Paul Walmsley:
ARM: OMAP2+: hwmod fixes for v4.2-rc
Two fixes against v4.2-rc1. The first, for DRA7xx platforms,
corrects some incorrect GPMC hardware description data. The
second one will ensure that the hwmod code will wait for any
module with CPU-accessible registers to become ready before
attempting to access it.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.2-rc/20150723065408/
Note that I do not have a DRA7xx or AM43xx board, and therefore
cannot test on those platforms.
* tag 'for-v4.2-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix _wait_target_ready() for hwmods without sysc
ARM: DRA7: hwmod: fix gpmc hwmod
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Since commit 3d42a379b6fa5b46058e3302b1802b29f64865bb
("can: flexcan: add 2nd clock to support imx53 and newer")
the can driver requires a dt nodes to have a second clock.
Add them to imx35 to fix probing the flex can driver on the
respective platforms.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
For hwmods without sysc, _init_mpu_rt_base(oh) won't be called and so
_find_mpu_rt_port(oh) will return NULL thus preventing ready state check
on those modules after the module is enabled.
This can potentially cause a bus access error if the module is accessed
before the module is ready.
Fix this by unconditionally calling _init_mpu_rt_base() during hwmod
_init(). Do ioremap only if we need SYSC access.
Eventhough _wait_target_ready() check doesn't really need MPU RT port but
just the PRCM registers, we still mandate that the hwmod must have an
MPU RT port if ready state check needs to be done. Else it would mean that
the module is not accessible by MPU so there is no point in waiting
for target to be ready.
e.g. this fixes the below DCAN bus access error on AM437x-gp-evm.
[ 16.672978] ------------[ cut here ]------------
[ 16.677885] WARNING: CPU: 0 PID: 1580 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x234/0x35c()
[ 16.687946] 44000000.ocp:L3 Custom Error: MASTER M2 (64-bit) TARGET L4_PER_0 (Read): Data Access in User mode during Functional access
[ 16.700654] Modules linked in: xhci_hcd btwilink ti_vpfe dwc3 videobuf2_core ov2659 bluetooth v4l2_common videodev ti_am335x_adc kfifo_buf industrialio c_can_platform videobuf2_dma_contig media snd_soc_tlv320aic3x pixcir_i2c_ts c_can dc
[ 16.731144] CPU: 0 PID: 1580 Comm: rpc.statd Not tainted 3.14.26-02561-gf733aa036398 #180
[ 16.739747] Backtrace:
[ 16.742336] [<c0011108>] (dump_backtrace) from [<c00112a4>] (show_stack+0x18/0x1c)
[ 16.750285] r6:00000093 r5:00000009 r4:eab5b8a8 r3:00000000
[ 16.756252] [<c001128c>] (show_stack) from [<c05a4418>] (dump_stack+0x20/0x28)
[ 16.763870] [<c05a43f8>] (dump_stack) from [<c0037120>] (warn_slowpath_common+0x6c/0x8c)
[ 16.772408] [<c00370b4>] (warn_slowpath_common) from [<c00371e4>] (warn_slowpath_fmt+0x38/0x40)
[ 16.781550] r8:c05d1f90 r7:c0730844 r6:c0730448 r5:80080003 r4:ed0cd210
[ 16.788626] [<c00371b0>] (warn_slowpath_fmt) from [<c027fa94>] (l3_interrupt_handler+0x234/0x35c)
[ 16.797968] r3:ed0cd480 r2:c0730508
[ 16.801747] [<c027f860>] (l3_interrupt_handler) from [<c0063758>] (handle_irq_event_percpu+0x54/0x1bc)
[ 16.811533] r10:ed005600 r9:c084855b r8:0000002a r7:00000000 r6:00000000 r5:0000002a
[ 16.819780] r4:ed0e6d80
[ 16.822453] [<c0063704>] (handle_irq_event_percpu) from [<c00638f0>] (handle_irq_event+0x30/0x40)
[ 16.831789] r10:eb2b6938 r9:eb2b6960 r8:bf011420 r7:fa240100 r6:00000000 r5:0000002a
[ 16.840052] r4:ed005600
[ 16.842744] [<c00638c0>] (handle_irq_event) from [<c00661d8>] (handle_fasteoi_irq+0x74/0x128)
[ 16.851702] r4:ed005600 r3:00000000
[ 16.855479] [<c0066164>] (handle_fasteoi_irq) from [<c0063068>] (generic_handle_irq+0x28/0x38)
[ 16.864523] r4:0000002a r3:c0066164
[ 16.868294] [<c0063040>] (generic_handle_irq) from [<c000ef60>] (handle_IRQ+0x38/0x8c)
[ 16.876612] r4:c081c640 r3:00000202
[ 16.880380] [<c000ef28>] (handle_IRQ) from [<c00084f0>] (gic_handle_irq+0x30/0x5c)
[ 16.888328] r6:eab5ba38 r5:c0804460 r4:fa24010c r3:00000100
[ 16.894303] [<c00084c0>] (gic_handle_irq) from [<c05a8d80>] (__irq_svc+0x40/0x50)
[ 16.902193] Exception stack(0xeab5ba38 to 0xeab5ba80)
[ 16.907499] ba20: 00000000 00000006
[ 16.916108] ba40: fa1d0000 fa1d0008 ed3d3000 eab5bab4 ed3d3460 c0842af4 bf011420 eb2b6960
[ 16.924716] ba60: eb2b6938 eab5ba8c eab5ba90 eab5ba80 bf035220 bf07702c 600f0013 ffffffff
[ 16.933317] r7:eab5ba6c r6:ffffffff r5:600f0013 r4:bf07702c
[ 16.939317] [<bf077000>] (c_can_plat_read_reg_aligned_to_16bit [c_can_platform]) from [<bf035220>] (c_can_get_berr_counter+0x38/0x64 [c_can])
[ 16.952696] [<bf0351e8>] (c_can_get_berr_counter [c_can]) from [<bf010294>] (can_fill_info+0x124/0x15c [can_dev])
[ 16.963480] r5:ec8c9740 r4:ed3d3000
[ 16.967253] [<bf010170>] (can_fill_info [can_dev]) from [<c0502fa8>] (rtnl_fill_ifinfo+0x58c/0x8fc)
[ 16.976749] r6:ec8c9740 r5:ed3d3000 r4:eb2b6780
[ 16.981613] [<c0502a1c>] (rtnl_fill_ifinfo) from [<c0503408>] (rtnl_dump_ifinfo+0xf0/0x1dc)
[ 16.990401] r10:ec8c9740 r9:00000000 r8:00000000 r7:00000000 r6:ebd4d1b4 r5:ed3d3000
[ 16.998671] r4:00000000
[ 17.001342] [<c0503318>] (rtnl_dump_ifinfo) from [<c050e6e4>] (netlink_dump+0xa8/0x1e0)
[ 17.009772] r10:00000000 r9:00000000 r8:c0503318 r7:ebf3e6c0 r6:ebd4d1b4 r5:ec8c9740
[ 17.018050] r4:ebd4d000
[ 17.020714] [<c050e63c>] (netlink_dump) from [<c050ec10>] (__netlink_dump_start+0x104/0x154)
[ 17.029591] r6:eab5bd34 r5:ec8c9980 r4:ebd4d000
[ 17.034454] [<c050eb0c>] (__netlink_dump_start) from [<c0505604>] (rtnetlink_rcv_msg+0x110/0x1f4)
[ 17.043778] r7:00000000 r6:ec8c9980 r5:00000f40 r4:ebf3e6c0
[ 17.049743] [<c05054f4>] (rtnetlink_rcv_msg) from [<c05108e8>] (netlink_rcv_skb+0xb4/0xc8)
[ 17.058449] r8:eab5bdac r7:ec8c9980 r6:c05054f4 r5:ec8c9980 r4:ebf3e6c0
[ 17.065534] [<c0510834>] (netlink_rcv_skb) from [<c0504134>] (rtnetlink_rcv+0x24/0x2c)
[ 17.073854] r6:ebd4d000 r5:00000014 r4:ec8c9980 r3:c0504110
[ 17.079846] [<c0504110>] (rtnetlink_rcv) from [<c05102ac>] (netlink_unicast+0x180/0x1ec)
[ 17.088363] r4:ed0c6800 r3:c0504110
[ 17.092113] [<c051012c>] (netlink_unicast) from [<c0510670>] (netlink_sendmsg+0x2ac/0x380)
[ 17.100813] r10:00000000 r8:00000008 r7:ec8c9980 r6:ebd4d000 r5:eab5be70 r4:eab5bee4
[ 17.109083] [<c05103c4>] (netlink_sendmsg) from [<c04dfdb4>] (sock_sendmsg+0x90/0xb0)
[ 17.117305] r10:00000000 r9:eab5a000 r8:becdda3c r7:0000000c r6:ea978400 r5:eab5be70
[ 17.125563] r4:c05103c4
[ 17.128225] [<c04dfd24>] (sock_sendmsg) from [<c04e1c28>] (SyS_sendto+0xb8/0xdc)
[ 17.136001] r6:becdda5c r5:00000014 r4:ecd37040
[ 17.140876] [<c04e1b70>] (SyS_sendto) from [<c000e680>] (ret_fast_syscall+0x0/0x30)
[ 17.148923] r10:00000000 r8:c000e804 r7:00000122 r6:becdda5c r5:0000000c r4:becdda5c
[ 17.157169] ---[ end trace 2b71e15b38f58bad ]---
Fixes: 6423d6df1440 ("ARM: OMAP2+: hwmod: check for module address space during init")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: <stable@vger.kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes for v4.2" from Kukjin Kim:
From Krzysztof Kozlowski:
1. Fix exynos3250 MIPI DSI display and MIPI CSIS-2 camera sensorx
after adding support for PMU regmap in exynos-video-mipi driver
(issue introduced in v4.0).
2. Bring back cpufreq for exynos4210 after incomplete switch to
cpufreq-dt driver in 4.2 merge window. The necessary DT changes
for exynos4210 cpufreq was not applied to the same tree as rest
of patchset because of multiple conflicts between clk and arm-soc
trees. Unfortunately without the change the exynos4210 boards
loose cpufreq feature.
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add CPU OPP and regulator supply property for exynos4210
ARM: dts: Update video-phy node with syscon phandle for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
For Exynos4210 platforms, add CPU operating points and CPU regulator
supply properties for migrating from Exynos specific cpufreq driver
to using generic cpufreq driver.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Andreas Farber <afaerber@suse.de>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[b.zolnierkie: removed exynos5250 and exynos5420 support for now]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[k.kozlowski: Rebased, moved cpu nodes to alphabetical position]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
As a follow-up to recent changes to Exynos mipi video phy driver,
introducing support for PMU regmap in commit e4b3d38088df ("phy:
exynos-video-mipi: Fix regression by adding support for PMU regmap")
add a syscon phandle to video-phy node to bring back to life both
MIPI DSI display and MIPI CSIS-2 camera sensor on Exynos3250.
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Merge "pxa fixes for v4.2" from Robert Jarzmik:
ARM: pxa: fixes for v4.2-rc2
This single fix reenables ethernet cards for several pxa boards,
broken by regulator addition to dm9000 driver.
* tag 'pxa-fixes-v4.2-rc2' of https://github.com/rjarzmik/linux:
ARM: pxa: fix dm9000 platform data regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes
Merge "ARM: Couple of dts fixes for v4.2-rcx" from Santosh Shilimkar:
Couple of DTS fixes 4.2-rcx for Keystone EVMs:
K2E EVM boot hangs because of missing serdes driver which is needed to bring up
PCIe on K2E. These couple of fixes makes the PCIE disabled on common default and
let the specific board DTS to enable it.
* tag 'keystone-dts-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Now that PCIe DT binding is disabled in SoC specific DTS,
we need a way to override it in a board specific DTS. So
rename the PCIe nodes accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Currently PCIe DT bindings are broken. PCIe driver can't function
without having a SerDes driver that provide the phy configuration.
On K2E EVM, this causes problem since the EVM has Marvell SATA
controller present and with default values in the SerDes register,
it seems to pass the PCIe link check, but causes issues since
the configuration is not correct. The manifestation is that when
EVM is booted with NFS rootfs, the boot hangs. We shouldn't enable
PCIe on this EVM since to work, SerDes driver has to be present as
well. So by default, the PCIe DT binding should be disabled in SoC
specific DTS. It can be enabled in the board specific DTS when the
SerDes device driver is also present.
So fix the status of PCIe DT bindings in the SoC specific DTS to
"disabled". To enable PCIe, the status should be set to "ok" in
the EVM DTS file when SerDes driver support becomes available in
the upstream tree.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Since dm9000 driver added support for a vcc regulator, platform data
based platforms have their ethernet broken, as the regulator claiming
returns -EPROBE_DEFER and prevents dm9000 loading.
This patch fixes this for all pxa boards using dm9000, by using the
specific regulator_has_full_constraints() function.
This was discovered and tested on the cm-x300 board.
Fixes: 7994fe55a4a2 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
GPMC smart idle is not really broken but it does not support
smart idle with wakeup.
Fixes: 556708fe8718 ("ARM: OMAP: DRA7: hwmod: Make gpmc software supervised as the smart idle is broken")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps, all dts changes except for one:
- Fix up LCD panel name for overo boards
- Three fixes for pepper board for regulators, freqeuncy
scaling and audio input. Note that there is still one
issue being worked on for booting with multi_v7_defconfig
- Add missing #iommu-cells for omap4 and 5
- Add missing HAVE_ARM_SCU for am43xx
* tag 'omap-for-v4.2/fixes-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (210 commits)
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
ARM: dts: omap3: overo: Update LCD panel names
+ Linux 4.2-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Audio-in was incorrectly routed to Line In. It should be Mic3L as per
schematic.
Using mic-bias voltage at 2.0v (<0x1>) does not work for some reason. There
is no voltage seen on micbias (R127). Mic-bias voltage of 2.5v (<0x2>) works.
I see voltage of 2.475v across GND and micbias.
With these changes, I can record audio with a pair of proliferate TRRS earbuds.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Acked-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
CONFIG_HAVE_ARM_SCU only gets selected if CONFIG_SMP is selected in an OMAP
system, however AM43XX needs this option regardless of CONFIG_SMP and also
for an AM43XX only build as it is important for controlling power in the SoC.
Without this we cannot suspend the CPU for SoC suspend or cpuidle. The
ARM Cortex A9 needs SCU CPU Power Status bits to be set to off mode in order
for the PRCM to transition the MPU to low power modes.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 4.2" from Shawn Guo:
The i.MX fixes for 4.2:
- Correct compatible string for i.MX27 GPT which actually shares the
same programming model as i.MX21 GPT rather than i.MX1 one.
- Add missing #io-channel-cells property for i.MX23 LRADC device, which
is required for the device to be an IIO provider.
- Correct HSYNC/VSYNC pins and add ddc-i2c-bus property for TVE device
on imx53-qsb to work properly.
- Always enable PU domain if CONFIG_PM is not set. This fixes a couple
of failure scenarios which will hang the system if one of the devices
in the PU domain is accessed.
* tag 'imx-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
ARM: dts: imx53-qsb: fix TVE entry
ARM: dts: mx23: fix iio-hwmon support
ARM: dts: imx27: Adjust the GPT compatible string
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The 'digicolor' regexp doesn't cover the dts files. Add a glob pattern for
them.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into fixes
Merge "SoCFPGA fixes for v4.2-rc1" from Dinh Nguyen:
SoCFPGA fixes against v4.2-rc1
- Update compatible "adxl345x" compatible string
- Alphabetize the DTS nodes for the C5 sockit board file
* tag 'socfpga_fixes_for_v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: Fix entries order
ARM: socfpga: dts: Fix adxl34x formating and compatible string
|
|
Ux500 is regressing due to commit
a21763a0b1e5a5ab8310f581886d04beadc16616
"pinctrl: nomadik: activate strict mux mode" which disallows
Nomadik GPIO 5 to be muxed in as a level shifter voltage select
pin, as it is currently described as being used for RX on UART1.
The behaviour is correct, instead the hardware config has been
incorrecly specified: UART1 is indeed unused on HREFv60plus and
Snowball and that is why HREFv60plus can use the pins it would
normally occupy as the voltage select line for the MMC/SD
levelshifter (Snowball uses it for I2C4).
The reason UART1 was anyway enabled on these platforms was
probably to secure the port enumeration to userspace. This
can be solved by using aliases (done in a separate patch) so
we can now deactivate UART1 and let MMC/SD use it properly
on HREFv60plus. We explicitly activate it only for the
older HREFprev60 board.
To complete, we set up the pin configuration for these pins
properly in the sdi0 node.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This enumerates the PL011 serial ports on the Ux500. This is
necessary to do if we want to remove one of the serial ports,
since userspace depends on console to be present on ttyAMA2
and we must not break userspace.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP5 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP4 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The device tree for Gumstix Pepper has DCDC2 and
DCDC3 correctly labelled but the upper limit values
are wrong. The confusion is due to the hardware
quirk where the DCDC2 and DCDC3 wires are flipped
in Pepper.
Signed-off-by: Arun Bharadwaj <arun@gumstix.com>
Tested-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Boot process is halting in midway because some of the necessary voltage
regulators are deemed unused and subsequently powered off, leading to
a completely unresponsive system.
Most of the device nodes had correct voltage regulator attachments.
Yet these nodes had to set stricter enforcement on them through
'regulator-boot-on' and 'regulator-always-on' to function correctly.
The consumers of the regulators this commit affect are the followings:
DCDC1: vdd_1v8 system supply, USB-PHY, and ADC
DCDC2: Core domain
DCDC3: MPU core domain
LDO1: RTC
LDO2: 3v3 IO domain
LDO3: USB-PHY; not a boot-time requirement
LDO4: LCD [16:23]
All but LDO3 need to be always-on for the system to be functional.
Additionally regulator-name properties have been added for the kernel to
display the name from the schematic. This will improve diagnostics.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For Gumstix Overo COMs, the u-boot bootloader typically passes an
argument specifying the default display via the omapdss.def_disp
parameter. When a default display is specified, DSS2 tries to match
this name with either the device tree label (e.g. label=dvi) or,
failing this, the device tree alias (e.g. label=display0). Update the
panel names for the 'lcd43' and 'lcd35' displays in the device tree
such that they match the names passed by u-boot.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add support for 4 Japanese keys
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
|
|
This reverts commit dec4f799d0a4c9edae20512fa60b0a36f3299ca2.
Jörg Otte reports a NULL pointder dereference due to this commit, as
'crtc_state' very much can be NULL:
crtc_state = state->base.state ?
intel_atomic_get_crtc_state(state->base.state, intel_crtc) : NULL;
So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.
There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS fixes from Al Viro:
"Fixes for this cycle regression in overlayfs and a couple of
long-standing (== all the way back to 2.6.12, at least) bugs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
freeing unlinked file indefinitely delayed
fix a braino in ovl_d_select_inode()
9p: don't leave a half-initialized inode sitting around
|
|
Pull MIPS fixes from Ralf Baechle:
"A fair number of 4.2 fixes also because Markos opened the flood gates.
- Patch up the math used calculate the location for the page bitmap.
- The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ
around was causing issues on non-Malta platforms, so move the code
to a Malta specific location.
- A spelling fix replicated through several files.
- Fix to the emulation of an R2 instruction for R6 cores.
- Fix the JR emulation for R6.
- Further patching of mindless 64 bit issues.
- Ensure the kernel won't crash on CPUs with L2 caches with >= 8
ways.
- Use compat_sys_getsockopt for O32 ABI on 64 bit kernels.
- Fix cache flushing for multithreaded cores.
- A build fix"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: O32: Use compat_sys_getsockopt.
MIPS: c-r4k: Extend way_string array
MIPS: Pistachio: Support CDMM & Fast Debug Channel
MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
MIPS: c-r4k: Fix cache flushing for MT cores
Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
MIPS: cps-vec: Use macros for various arithmetics and memory operations
MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0
MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit
MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2
MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA
MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting
MIPS: Fix erroneous JR emulation for MIPS R6
MIPS: Fix branch emulation for BLTC and BGEC instructions
MIPS: kernel: traps: Fix broken indentation
MIPS: bootmem: Don't use memory holes for page bitmap
MIPS: O32: Do not handle require 32 bytes from the stack to be readable.
MIPS, CPUFREQ: Fix spelling of Institute.
MIPS: Lemote 2F: Fix build caused by recent mass rename.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- the high latency PIT detection fix, which slipped through the cracks
for rc1
- a regression fix for the early printk mechanism
- the x86 part to plug irq/vector related hotplug races
- move the allocation of the espfix pages on cpu hotplug to non atomic
context. The current code triggers a might_sleep() warning.
- a series of KASAN fixes addressing boot crashes and usability
- a trivial typo fix for Kconfig help text
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text
x86/irq: Retrieve irq data after locking irq_desc
x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable()
x86/irq: Plug irq vector hotplug race
x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8'
x86/espfix: Init espfix on the boot CPU side
x86/espfix: Add 'cpu' parameter to init_espfix_ap()
x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig
x86/kasan: Add message about KASAN being initialized
x86/kasan: Fix boot crash on AMD processors
x86/kasan: Flush TLBs after switching CR3
x86/kasan: Fix KASAN shadow region page tables
x86/init: Clear 'init_level4_pgt' earlier
x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"This update from the timer departement contains:
- A series of patches which address a shortcoming in the tick
broadcast code.
If the broadcast device is not available or an hrtimer emulated
broadcast device, some of the original assumptions lead to boot
failures. I rather plugged all of the corner cases instead of only
addressing the issue reported, so the change got a little larger.
Has been extensivly tested on x86 and arm.
- Get rid of the last holdouts using do_posix_clock_monotonic_gettime()
- A regression fix for the imx clocksource driver
- An update to the new state callbacks mechanism for clockevents.
This is required to simplify the conversion, which will take place
in 4.3"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Prevent NULL pointer dereference
time: Get rid of do_posix_clock_monotonic_gettime
cris: Replace do_posix_clock_monotonic_gettime()
tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build
tick/broadcast: Handle spurious interrupts gracefully
tick/broadcast: Check for hrtimer broadcast active early
tick/broadcast: Return busy when IPI is pending
tick/broadcast: Return busy if periodic mode and hrtimer broadcast
tick/broadcast: Move the check for periodic mode inside state handling
tick/broadcast: Prevent deep idle if no broadcast device available
tick/broadcast: Make idle check independent from mode and config
tick/broadcast: Sanity check the shutdown of the local clock_event
tick/broadcast: Prevent hrtimer recursion
clockevents: Allow set-state callbacks to be optional
clocksource/imx: Define clocksource for mx27
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for a cpu hotplug race vs. interrupt descriptors:
Prevent irq setup/teardown across the cpu starting/dying parts of cpu
hotplug so that the starting/dying cpu has a stable view of the
descriptor space. This has been an issue for all architectures in the
cpu dying phase, where interrupts are migrated away from the dying
cpu. In the starting phase its mostly a x86 issue vs the vector space
update"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hotplug: Prevent alloc/free of irq descriptors during cpu up/down
|
|
Normally opening a file, unlinking it and then closing will have
the inode freed upon close() (provided that it's not otherwise busy and
has no remaining links, of course). However, there's one case where that
does *not* happen. Namely, if you open it by fhandle with cold dcache,
then unlink() and close().
In normal case you get d_delete() in unlink(2) notice that dentry
is busy and unhash it; on the final dput() it will be forcibly evicted from
dcache, triggering iput() and inode removal. In this case, though, we end
up with *two* dentries - disconnected (created by open-by-fhandle) and
regular one (used by unlink()). The latter will have its reference to inode
dropped just fine, but the former will not - it's considered hashed (it
is on the ->s_anon list), so it will stay around until the memory pressure
will finally do it in. As the result, we have the final iput() delayed
indefinitely. It's trivial to reproduce -
void flush_dcache(void)
{
system("mount -o remount,rw /");
}
static char buf[20 * 1024 * 1024];
main()
{
int fd;
union {
struct file_handle f;
char buf[MAX_HANDLE_SZ];
} x;
int m;
x.f.handle_bytes = sizeof(x);
chdir("/root");
mkdir("foo", 0700);
fd = open("foo/bar", O_CREAT | O_RDWR, 0600);
close(fd);
name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0);
flush_dcache();
fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR);
unlink("foo/bar");
write(fd, buf, sizeof(buf));
system("df ."); /* 20Mb eaten */
close(fd);
system("df ."); /* should've freed those 20Mb */
flush_dcache();
system("df ."); /* should be the same as #2 */
}
will spit out something like
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 283282 21692 93% /
- inode gets freed only when dentry is finally evicted (here we trigger
than by remount; normally it would've happened in response to memory
pressure hell knows when).
Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/
Acked-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
when opening a directory we want the overlayfs inode, not one from
the topmost layer.
Reported-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Tested-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Cc: stable@vger.kernel.org # all branches
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
