| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Including asm/cacheflush.h first results in the following build error
when trying to build sparc32:allmodconfig, because 'struct page' has not
been declared, and the function declaration ends up creating a separate
(private) declaration of struct page (as a result of function arguments
being in the scope of the function declaration and definition, not in
global scope).
The C scoping rules do not just affect variable visibility, they also
affect type declaration visibility.
The end result is that when the actual call site is seen in
<linux/highmem.h>, the 'struct page' type in the caller is not the same
'struct page' that the function was declared with, resulting in:
In file included from arch/sparc/include/asm/page.h:10:0,
...
from drivers/staging/media/omap4iss/iss_video.c:15:
include/linux/highmem.h: In function 'clear_user_highpage':
include/linux/highmem.h:137:31: error:
passing argument 1 of 'sparc_flush_page_to_ram' from incompatible
pointer type
Include generic includes files first to fix the problem.
Fixes: fc96d58c10162 ("[media] v4l: omap4iss: Add support for OMAP4 camera interface - Video devices")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ Added explanation of C scope rules - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Make sure we don't go over the maximum jump stack boundary,
from Taehee Yoo.
2) Missing rcu_barrier() in hash and rbtree sets, also from Taehee.
3) Missing check to nul-node in rbtree timeout routine, from Taehee.
4) Use dev->name from flowtable to fix a memleak, from Florian.
5) Oneliner to free flowtable object on removal, from Florian.
6) Memleak in chain rename transaction, again from Florian.
7) Don't allow two chains to use the same name in the same
transaction, from Florian.
8) handle DCCP SYNC/SYNCACK as invalid, this triggers an
uninitialized timer in conntrack reported by syzbot, from Florian.
9) Fix leak in case netlink_dump_start() fails, from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Only a few fixes:
* always keep regulatory user hint
* add missing break statement in station flags parsing
* fix non-linear SKBs in port-control-over-nl80211
* reconfigure VLAN stations during HW restart
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently user regulatory hint is ignored if all wiphys
in the system are self managed. But the hint is not ignored
if there is no wiphy in the system. This affects the global
regulatory setting. Global regulatory setting needs to be
maintained so that it can be applied to a new wiphy entering
the system. Therefore, do not ignore user regulatory setting
even if all wiphys in the system are self managed.
Signed-off-by: Amar Singhal <asinghal@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The s390 build currently fails with the latent entropy plugin:
arch/s390/kernel/als.o: In function `verify_facilities':
als.c:(.init.text+0x24): undefined reference to `latent_entropy'
als.c:(.init.text+0xae): undefined reference to `latent_entropy'
make[3]: *** [arch/s390/boot/compressed/vmlinux] Error 1
make[2]: *** [arch/s390/boot/compressed/vmlinux] Error 2
make[1]: *** [bzImage] Error 2
This will be fixed with the early boot rework from Vasily, which
is planned for the 4.19 merge window.
For 4.18 the simplest solution is to disable the gcc plugins and
reenable them after the early boot rework is upstream.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Current sg coalescing logic in sk_alloc_sg() (latter is used by tls and
sockmap) is not quite correct in that we do fetch the previous sg entry,
however the subsequent check whether the refilled page frag from the
socket is still the same as from the last entry with prior offset and
length matching the start of the current buffer is comparing always the
first sg list entry instead of the prior one.
Fixes: 3c4d7559159b ("tls: kernel TLS support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch ensures the member->offset of a struct
is in the correct order (i.e the later member's offset cannot
go backward).
The current "pahole -J" BTF encoder does not generate something
like this. However, checking this can ensure future encoder
will not violate this.
Fixes: 69b693f0aefa ("bpf: btf: Introduce BPF Type Format (BTF)")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Shaochun Chen points out we leak dumper filter state allocations
stored in dump_control->data in case there is an error before netlink sets
cb_running (after which ->done will be called at some point).
In order to fix this, add .start functions and do the allocations
there.
->done is going to clean up, and in case error occurs before
->start invocation no cleanups need to be done anymore.
Reported-by: shaochun chen <cscnull@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Eric Dumazet says:
====================
Juha-Matti Tilli reported that malicious peers could inject tiny
packets in out_of_order_queue, forcing very expensive calls
to tcp_collapse_ofo_queue() and tcp_prune_ofo_queue() for
every incoming packet.
With tcp_rmem[2] default of 6MB, the ooo queue could
contain ~7000 nodes.
This patch series makes sure we cut cpu cycles enough to
render the attack not critical.
We might in the future go further, like disconnecting
or black-holing proven malicious flows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case skb in out_or_order_queue is the result of
multiple skbs coalescing, we would like to get a proper gso_segs
counter tracking, so that future tcp_drop() can report an accurate
number.
I chose to not implement this tracking for skbs in receive queue,
since they are not dropped, unless socket is disconnected.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to be able to give better diagnostics and detect
malicious traffic, we need to have better sk->sk_drops tracking.
Fixes: 9f5afeae5152 ("tcp: use an RB tree for ooo receive queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case an attacker feeds tiny packets completely out of order,
tcp_collapse_ofo_queue() might scan the whole rb-tree, performing
expensive copies, but not changing socket memory usage at all.
1) Do not attempt to collapse tiny skbs.
2) Add logic to exit early when too many tiny skbs are detected.
We prefer not doing aggressive collapsing (which copies packets)
for pathological flows, and revert to tcp_prune_ofo_queue() which
will be less expensive.
In the future, we might add the possibility of terminating flows
that are proven to be malicious.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Right after a TCP flow is created, receiving tiny out of order
packets allways hit the condition :
if (atomic_read(&sk->sk_rmem_alloc) >= sk->sk_rcvbuf)
tcp_clamp_window(sk);
tcp_clamp_window() increases sk_rcvbuf to match sk_rmem_alloc
(guarded by tcp_rmem[2])
Calling tcp_collapse_ofo_queue() in this case is not useful,
and offers a O(N^2) surface attack to malicious peers.
Better not attempt anything before full queue capacity is reached,
forcing attacker to spend lots of resource and allow us to more
easily detect the abuse.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Juha-Matti Tilli reported that malicious peers could inject tiny
packets in out_of_order_queue, forcing very expensive calls
to tcp_collapse_ofo_queue() and tcp_prune_ofo_queue() for
every incoming packet. out_of_order_queue rb-tree can contain
thousands of nodes, iterating over all of them is not nice.
Before linux-4.9, we would have pruned all packets in ofo_queue
in one go, every XXXX packets. XXXX depends on sk_rcvbuf and skbs
truesize, but is about 7000 packets with tcp_rmem[2] default of 6 MB.
Since we plan to increase tcp_rmem[2] in the future to cope with
modern BDP, can not revert to the old behavior, without great pain.
Strategy taken in this patch is to purge ~12.5 % of the queue capacity.
Fixes: 36a6503fedda ("tcp: refine tcp_prune_ofo_queue() to not drop all packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb hash for locally generated ip[v6] fragments belonging
to the same datagram can vary in several circumstances:
* for connected UDP[v6] sockets, the first fragment get its hash
via set_owner_w()/skb_set_hash_from_sk()
* for unconnected IPv6 UDPv6 sockets, the first fragment can get
its hash via ip6_make_flowlabel()/skb_get_hash_flowi6(), if
auto_flowlabel is enabled
For the following frags the hash is usually computed via
skb_get_hash().
The above can cause OoO for unconnected IPv6 UDPv6 socket: in that
scenario the egress tx queue can be selected on a per packet basis
via the skb hash.
It may also fool flow-oriented schedulers to place fragments belonging
to the same datagram in different flows.
Fix the issue by copying the skb hash from the head frag into
the others at fragmentation time.
Before this commit:
perf probe -a "dev_queue_xmit skb skb->hash skb->l4_hash:b1@0/8 skb->sw_hash:b1@1/8"
netperf -H $IPV4 -t UDP_STREAM -l 5 -- -m 2000 -n &
perf record -e probe:dev_queue_xmit -e probe:skb_set_owner_w -a sleep 0.1
perf script
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=3713014309 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=0 l4_hash=0 sw_hash=0
After this commit:
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0
Fixes: b73c3d0e4f0e ("net: Save TX flow hash in sock and set in skbuf on xmit")
Fixes: 67800f9b1f4e ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the code path where only rcu read lock is held, e.g. in the route
lookup code path, it is not safe to directly call fib6_info_hold()
because the fib6_info may already have been deleted but still exists
in the rcu grace period. Holding reference to it could cause double
free and crash the kernel.
This patch adds a new function fib6_info_hold_safe() and replace
fib6_info_hold() in all necessary places.
Syzbot reported 3 crash traces because of this. One of them is:
8021q: adding VLAN 0 to HW filter on device team0
IPv6: ADDRCONF(NETDEV_CHANGE): team0: link becomes ready
dst_release: dst:(____ptrval____) refcnt:-1
dst_release: dst:(____ptrval____) refcnt:-2
WARNING: CPU: 1 PID: 4845 at include/net/dst.h:239 dst_hold include/net/dst.h:239 [inline]
WARNING: CPU: 1 PID: 4845 at include/net/dst.h:239 ip6_setup_cork+0xd66/0x1830 net/ipv6/ip6_output.c:1204
dst_release: dst:(____ptrval____) refcnt:-1
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 4845 Comm: syz-executor493 Not tainted 4.18.0-rc3+ #10
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
panic+0x238/0x4e7 kernel/panic.c:184
dst_release: dst:(____ptrval____) refcnt:-2
dst_release: dst:(____ptrval____) refcnt:-3
__warn.cold.8+0x163/0x1ba kernel/panic.c:536
dst_release: dst:(____ptrval____) refcnt:-4
report_bug+0x252/0x2d0 lib/bug.c:186
fixup_bug arch/x86/kernel/traps.c:178 [inline]
do_error_trap+0x1fc/0x4d0 arch/x86/kernel/traps.c:296
dst_release: dst:(____ptrval____) refcnt:-5
do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:316
invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:992
RIP: 0010:dst_hold include/net/dst.h:239 [inline]
RIP: 0010:ip6_setup_cork+0xd66/0x1830 net/ipv6/ip6_output.c:1204
Code: c1 ed 03 89 9d 18 ff ff ff 48 b8 00 00 00 00 00 fc ff df 41 c6 44 05 00 f8 e9 2d 01 00 00 4c 8b a5 c8 fe ff ff e8 1a f6 e6 fa <0f> 0b e9 6a fc ff ff e8 0e f6 e6 fa 48 8b 85 d0 fe ff ff 48 8d 78
RSP: 0018:ffff8801a8fcf178 EFLAGS: 00010293
RAX: ffff8801a8eba5c0 RBX: 0000000000000000 RCX: ffffffff869511e6
RDX: 0000000000000000 RSI: ffffffff869515b6 RDI: 0000000000000005
RBP: ffff8801a8fcf2c8 R08: ffff8801a8eba5c0 R09: ffffed0035ac8338
R10: ffffed0035ac8338 R11: ffff8801ad6419c3 R12: ffff8801a8fcf720
R13: ffff8801a8fcf6a0 R14: ffff8801ad6419c0 R15: ffff8801ad641980
ip6_make_skb+0x2c8/0x600 net/ipv6/ip6_output.c:1768
udpv6_sendmsg+0x2c90/0x35f0 net/ipv6/udp.c:1376
inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798
sock_sendmsg_nosec net/socket.c:641 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:651
___sys_sendmsg+0x51d/0x930 net/socket.c:2125
__sys_sendmmsg+0x240/0x6f0 net/socket.c:2220
__do_sys_sendmmsg net/socket.c:2249 [inline]
__se_sys_sendmmsg net/socket.c:2246 [inline]
__x64_sys_sendmmsg+0x9d/0x100 net/socket.c:2246
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x446ba9
Code: e8 cc bb 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fb39a469da8 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 00000000006dcc54 RCX: 0000000000446ba9
RDX: 00000000000000b8 RSI: 0000000020001b00 RDI: 0000000000000003
RBP: 00000000006dcc50 R08: 00007fb39a46a700 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 45c828efc7a64843
R13: e6eeb815b9d8a477 R14: 5068caf6f713c6fc R15: 0000000000000001
Dumping ftrace buffer:
(ftrace buffer empty)
Kernel Offset: disabled
Rebooting in 86400 seconds..
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: syzbot+902e2a1bcd4f7808cef5@syzkaller.appspotmail.com
Reported-by: syzbot+8ae62d67f647abeeceb9@syzkaller.appspotmail.com
Reported-by: syzbot+3f08feb14086930677d0@syzkaller.appspotmail.com
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-07-23
this is a pull request of 12 patches for net/master.
The patch by Stephane Grosjean for the peak_canfd CAN driver fixes a problem
with older firmware. The next patch is by Roman Fietze and fixes the setup of
the CCCR register in the m_can driver. Nicholas Mc Guire's patch for the
mpc5xxx_can driver adds missing error checking. The two patches by Faiz Abbas
fix the runtime resume and clean up the probe function in the m_can driver. The
last 7 patches by Anssi Hannula fix several problem in the xilinx_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several issues with the suspend/resume handling code of the
driver:
- The device is attached and detached in the runtime_suspend() and
runtime_resume() callbacks if the interface is running. However,
during xcan_chip_start() the interface is considered running,
causing the resume handler to incorrectly call netif_start_queue()
at the beginning of xcan_chip_start(), and on xcan_chip_start() error
return the suspend handler detaches the device leaving the user
unable to bring-up the device anymore.
- The device is not brought properly up on system resume. A reset is
done and the code tries to determine the bus state after that.
However, after reset the device is always in Configuration mode
(down), so the state checking code does not make sense and
communication will also not work.
- The suspend callback tries to set the device to sleep mode (low-power
mode which monitors the bus and brings the device back to normal mode
on activity), but then immediately disables the clocks (possibly
before the device reaches the sleep mode), which does not make sense
to me. If a clean shutdown is wanted before disabling clocks, we can
just bring it down completely instead of only sleep mode.
Reorganize the PM code so that only the clock logic remains in the
runtime PM callbacks and the system PM callbacks contain the device
bring-up/down logic. This makes calling the runtime PM callbacks during
e.g. xcan_chip_start() safe.
The system PM callbacks now simply call common code to start/stop the
HW if the interface was running, replacing the broken code from before.
xcan_chip_stop() is updated to use the common reset code so that it will
wait for the reset to complete. Reset also disables all interrupts so do
not do that separately.
Also, the device_may_wakeup() checks are removed as the driver does not
have wakeup support.
Tested on Zynq-7000 integrated CAN.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
xcan_interrupt() clears ERROR|RXOFLV|BSOFF|ARBLST interrupts if any of
them is asserted. This does not take into account that some of them
could have been asserted between interrupt status read and interrupt
clear, therefore clearing them without handling them.
Fix the code to only clear those interrupts that it knows are asserted
and therefore going to be processed in xcan_err_interrupt().
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
RX overflow interrupt (RXOFLW) is disabled even though xcan_interrupt()
processes it. This means that an RX overflow interrupt will only be
processed when another interrupt gets asserted (e.g. for RX/TX).
Fix that by enabling the RXOFLW interrupt.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The xilinx_can driver assumes that the TXOK interrupt only clears after
it has been acknowledged as many times as there have been successfully
sent frames.
However, the documentation does not mention such behavior, instead
saying just that the interrupt is cleared when the clear bit is set.
Similarly, testing seems to also suggest that it is immediately cleared
regardless of the amount of frames having been sent. Performing some
heavy TX load and then going back to idle has the tx_head drifting
further away from tx_tail over time, steadily reducing the amount of
frames the driver keeps in the TX FIFO (but not to zero, as the TXOK
interrupt always frees up space for 1 frame from the driver's
perspective, so frames continue to be sent) and delaying the local echo
frames.
The TX FIFO tracking is also otherwise buggy as it does not account for
TX FIFO being cleared after software resets, causing
BUG!, TX FIFO full when queue awake!
messages to be output.
There does not seem to be any way to accurately track the state of the
TX FIFO for local echo support while using the full TX FIFO.
The Zynq version of the HW (but not the soft-AXI version) has watermark
programming support and with it an additional TX-FIFO-empty interrupt
bit.
Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI
and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used
to detect whether 1 or 2 frames have been sent at interrupt processing
time.
Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode
was also tested.
An alternative way to solve this would be to drop local echo support but
keep using the full TX FIFO.
v2: Add FIFO space check before TX queue wake with locking to
synchronize with queue stop. This avoids waking the queue when xmit()
had just filled it.
v3: Keep local echo support and reduce the amount of frames in FIFO
instead as suggested by Marc Kleine-Budde.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The xilinx_can driver contains no mechanism for propagating recovery
from CAN_STATE_ERROR_WARNING and CAN_STATE_ERROR_PASSIVE.
Add such a mechanism by factoring the handling of
XCAN_STATE_ERROR_PASSIVE and XCAN_STATE_ERROR_WARNING out of
xcan_err_interrupt and checking for recovery after RX and TX if the
interface is in one of those states.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If the device gets into a state where RXNEMP (RX FIFO not empty)
interrupt is asserted without RXOK (new frame received successfully)
interrupt being asserted, xcan_rx_poll() will continue to try to clear
RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is
not empty, the interrupt will not be cleared and napi_schedule() will
just be called again.
This situation can occur when:
(a) xcan_rx() returns without reading RX FIFO due to an error condition.
The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear
due to a frame still being in the FIFO. The frame will never be read
from the FIFO as RXOK is no longer set.
(b) A frame is received between xcan_rx_poll() reading interrupt status
and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain
set as the new message is still in the FIFO.
I'm able to trigger case (b) by flooding the bus with frames under load.
There does not seem to be any benefit in using both RXNEMP and RXOK in
the way the driver does, and the polling example in the reference manual
(UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either
RXOK or RXNEMP can be used for detecting incoming messages.
Fix the issue and simplify the RX processing by only using RXNEMP
without RXOK.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The xilinx_can driver performs a software reset when an RX overrun is
detected. This causes the device to enter Configuration mode where no
messages are received or transmitted.
The documentation does not mention any need to perform a reset on an RX
overrun, and testing by inducing an RX overflow also indicated that the
device continues to work just fine without a reset.
Remove the software reset.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
MCAN message ram should only be accessed once clocks are enabled.
Therefore, move the call to parse/init the message ram to after
clocks are enabled.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
pm_runtime_get_sync() returns a 1 if the state of the device is already
'active'. This is not a failure case and should return a success.
Therefore fix error handling for pm_runtime_get_sync() call such that
it returns success when the value is 1.
Also cleanup the TODO for using runtime PM for sleep mode as that is
implemented.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
of_iomap() can return NULL so that return needs to be checked and NULL
treated as failure. While at it also take care of the missing
of_node_put() in the error path.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
checking can.ctrlmode
Inside m_can_chip_config(), when setting up the new value of the CCCR,
the CCCR_NISO bit is not cleared like the others, CCCR_TEST, CCCR_MON,
CCCR_BRSE and CCCR_FDOE, before checking the can.ctrlmode bits for
CAN_CTRLMODE_FD_NON_ISO.
This way once the controller was configured for CAN_CTRLMODE_FD_NON_ISO,
this mode could never be cleared again.
This fix is only relevant for controllers with version 3.1.x or 3.2.x.
Older versions do not support NISO.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The DMA logic in firmwares < v3.3.0 embedded in the PCAN-PCIe FD cards
family is not capable of handling a mix of 32-bit and 64-bit logical
addresses. If the board is equipped with 2 or 4 CAN ports, then such a
situation might lead to a PCIe Bus Error "Malformed TLP" packet
as well as "irq xx: nobody cared" issue.
This patch adds a workaround that requests only 32-bit DMA addresses
when these might be allocated outside of the 4 GB area.
This issue has been fixed in firmware v3.3.0 and next.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
|
|
Pull NVMe fixes from Christoph Hellwig:
- fix a regression in 4.18 that causes a memory leak on probe failure
(Keith Bush)
- fix a deadlock in the passthrough ioctl code (Scott Bauer)
- don't enable AENs if not supported (Weiping Zhang)
- fix an old regression in metadata handling in the passthrough ioctl
code (Roland Dreier)
* tag 'nvme-for-4.18' of git://git.infradead.org/nvme:
nvme: fix handling of metadata_len for NVME_IOCTL_IO_CMD
nvme: don't enable AEN if not supported
nvme: ensure forward progress during Admin passthru
nvme-pci: fix memory leak on probe failure
|
|
Pull vfs fixes from Al Viro:
"Fix several places that screw up cleanups after failures halfway
through opening a file (one open-coding filp_clone_open() and getting
it wrong, two misusing alloc_file()). That part is -stable fodder from
the 'work.open' branch.
And Christoph's regression fix for uapi breakage in aio series;
include/uapi/linux/aio_abi.h shouldn't be pulling in the kernel
definition of sigset_t, the reason for doing so in the first place had
been bogus - there's no need to expose struct __aio_sigset in
aio_abi.h at all"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
aio: don't expose __aio_sigset in uapi
ocxlflash_getfile(): fix double-iput() on alloc_file() failures
cxl_getfile(): fix double-iput() on alloc_file() failures
drm_mode_create_lease_ioctl(): fix open-coded filp_clone_open()
|
|
kernel_wait4() expects a userland address for status - it's only
rusage that goes as a kernel one (and needs a copyout afterwards)
[ Also, fix the prototype of kernel_wait4() to have that __user
annotation - Linus ]
Fixes: 92ebce5ac55d ("osf_wait4: switch to kernel_wait4()")
Cc: stable@kernel.org # v4.13+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Prevent drivers from building on PPC32 if they use isa_bus_to_virt(),
isa_virt_to_bus(), or isa_page_to_bus(), which are not available and
thus cause build errors.
../drivers/net/ethernet/3com/3c515.c: In function 'corkscrew_open':
../drivers/net/ethernet/3com/3c515.c:824:9: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/lance.c: In function 'lance_rx':
../drivers/net/ethernet/amd/lance.c:1203:23: error: implicit declaration of function 'isa_bus_to_virt'; did you mean 'bus_to_virt'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/ni65.c: In function 'ni65_init_lance':
../drivers/net/ethernet/amd/ni65.c:585:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
../drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously only the neighbour state was checked to decide if an offloaded
entry should be removed. However, there can be situations when the entry
is dead but still marked as valid. This can lead to dead entries not
being removed from fw tables or even incorrect data being added.
Check the entry dead bit before deciding if it should be added to or
removed from fw neighbour tables.
Fixes: 8e6a9046b66a ("nfp: flower vxlan neighbour offload")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Roopa Prabhu says:
====================
vxlan: fix default fdb entry user-space notify ordering/race
Problem:
In vxlan_newlink, a default fdb entry is added before register_netdev.
The default fdb creation function notifies user-space of the
fdb entry on the vxlan device which user-space does not know about yet.
(RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex).
This series fixes the user-space netlink notification ordering issue
with the following changes:
- decouple fdb notify from fdb create.
- Move fdb notify after register_netdev.
- modify rtnl_configure_link to allow configuring a link early.
- Call rtnl_configure_link in vxlan newlink handler to notify
userspace about the newlink before fdb notify and
hence avoiding the user-space race.
====================
Fixes: afbd8bae9c79 ("vxlan: add implicit fdb entry for default destination")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
|
|
Problem:
In vxlan_newlink, a default fdb entry is added before register_netdev.
The default fdb creation function also notifies user-space of the
fdb entry on the vxlan device which user-space does not know about yet.
(RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex).
This patch fixes the user-space netlink notification ordering issue
with the following changes:
- decouple fdb notify from fdb create.
- Move fdb notify after register_netdev.
- Call rtnl_configure_link in vxlan newlink handler to notify
userspace about the newlink before fdb notify and
hence avoiding the user-space race.
Fixes: afbd8bae9c79 ("vxlan: add implicit fdb entry for default destination")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new option do_notify to vxlan_fdb_destroy to make
sending netlink notify optional. Used by a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Add new vxlan_fdb_alloc helper
- rename existing vxlan_fdb_create into vxlan_fdb_update:
because it really creates or updates an existing
fdb entry
- move new fdb creation into a separate vxlan_fdb_create
Main motivation for this change is to introduce the ability
to decouple vxlan fdb creation and notify, used in a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtnl_configure_link sets dev->rtnl_link_state to
RTNL_LINK_INITIALIZED and unconditionally calls
__dev_notify_flags to notify user-space of dev flags.
current call sequence for rtnl_configure_link
rtnetlink_newlink
rtnl_link_ops->newlink
rtnl_configure_link (unconditionally notifies userspace of
default and new dev flags)
If a newlink handler wants to call rtnl_configure_link
early, we will end up with duplicate notifications to
user-space.
This patch fixes rtnl_configure_link to check rtnl_link_state
and call __dev_notify_flags with gchanges = 0 if already
RTNL_LINK_INITIALIZED.
Later in the series, this patch will help the following sequence
where a driver implementing newlink can call rtnl_configure_link
to initialize the link early.
makes the following call sequence work:
rtnetlink_newlink
rtnl_link_ops->newlink (vxlan) -> rtnl_configure_link (initializes
link and notifies
user-space of default
dev flags)
rtnl_configure_link (updates dev flags if requested by user ifm
and notifies user-space of new dev flags)
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Got crash report with following backtrace:
BUG: unable to handle kernel paging request at ffff8801869daffe
RIP: 0010:[<ffffffff816429c4>] [<ffffffff816429c4>] ip6_finish_output2+0x394/0x4c0
RSP: 0018:ffff880186c83a98 EFLAGS: 00010283
RAX: ffff8801869db00e ...
[<ffffffff81644cdc>] ip6_finish_output+0x8c/0xf0
[<ffffffff81644d97>] ip6_output+0x57/0x100
[<ffffffff81643dc9>] ip6_forward+0x4b9/0x840
[<ffffffff81645566>] ip6_rcv_finish+0x66/0xc0
[<ffffffff81645db9>] ipv6_rcv+0x319/0x530
[<ffffffff815892ac>] netif_receive_skb+0x1c/0x70
[<ffffffffc0060bec>] atl1c_clean+0x1ec/0x310 [atl1c]
...
The bad access is in neigh_hh_output(), at skb->data - 16 (HH_DATA_MOD).
atl1c driver provided skb with no headroom, so 14 bytes (ethernet
header) got pulled, but then 16 are copied.
Reserve NET_SKB_PAD bytes headroom, like netdev_alloc_skb().
Compile tested only; I lack hardware.
Fixes: 7b7017642199 ("atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two scenarios that we will restore deleted records. The first is
when device down and up(or unmap/remap). In this scenario the new filter
mode is same with previous one. Because we get it from in_dev->mc_list and
we do not touch it during device down and up.
The other scenario is when a new socket join a group which was just delete
and not finish sending status reports. In this scenario, we should use the
current filter mode instead of restore old one. Here are 4 cases in total.
old_socket new_socket before_fix after_fix
IN(A) IN(A) ALLOW(A) ALLOW(A)
IN(A) EX( ) TO_IN( ) TO_EX( )
EX( ) IN(A) TO_EX( ) ALLOW(A)
EX( ) EX( ) TO_EX( ) TO_EX( )
Fixes: 24803f38a5c0b (igmp: do not remove igmp souce list info when set link down)
Fixes: 1666d49e1d416 (mld: do not remove mld souce list info when set link down)
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
free_irq() waits until all handlers for this IRQ have completed. As the
relevant handler (mv88e6xxx_g1_irq_thread_fn()) takes the chip's reg_lock
it might never return if the thread calling free_irq() holds this lock.
For the same reason kthread_cancel_delayed_work_sync() in the polling case
must not hold this lock.
Also first free the irq (or stop the worker respectively) such that
mv88e6xxx_g1_irq_thread_work() isn't called any more before the irq
mappings are dropped in mv88e6xxx_g1_irq_free_common() to prevent the
worker thread to call handle_nested_irq(0) which results in a NULL-pointer
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot caught a NULL deref [1], caused by skb_segment()
skb_segment() has many "goto err;" that assume the @err variable
contains -ENOMEM.
A successful call to __skb_linearize() should not clear @err,
otherwise a subsequent memory allocation error could return NULL.
While we are at it, we might use -EINVAL instead of -ENOMEM when
MAX_SKB_FRAGS limit is reached.
[1]
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
CPU: 0 PID: 13285 Comm: syz-executor3 Not tainted 4.18.0-rc4+ #146
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:tcp_gso_segment+0x3dc/0x1780 net/ipv4/tcp_offload.c:106
Code: f0 ff ff 0f 87 1c fd ff ff e8 00 88 0b fb 48 8b 75 d0 48 b9 00 00 00 00 00 fc ff df 48 8d be 90 00 00 00 48 89 f8 48 c1 e8 03 <0f> b6 14 08 48 8d 86 94 00 00 00 48 89 c6 83 e0 07 48 c1 ee 03 0f
RSP: 0018:ffff88019b7fd060 EFLAGS: 00010206
RAX: 0000000000000012 RBX: 0000000000000020 RCX: dffffc0000000000
RDX: 0000000000040000 RSI: 0000000000000000 RDI: 0000000000000090
RBP: ffff88019b7fd0f0 R08: ffff88019510e0c0 R09: ffffed003b5c46d6
R10: ffffed003b5c46d6 R11: ffff8801dae236b3 R12: 0000000000000001
R13: ffff8801d6c581f4 R14: 0000000000000000 R15: ffff8801d6c58128
FS: 00007fcae64d6700(0000) GS:ffff8801dae00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004e8664 CR3: 00000001b669b000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
tcp4_gso_segment+0x1c3/0x440 net/ipv4/tcp_offload.c:54
inet_gso_segment+0x64e/0x12d0 net/ipv4/af_inet.c:1342
inet_gso_segment+0x64e/0x12d0 net/ipv4/af_inet.c:1342
skb_mac_gso_segment+0x3b5/0x740 net/core/dev.c:2792
__skb_gso_segment+0x3c3/0x880 net/core/dev.c:2865
skb_gso_segment include/linux/netdevice.h:4099 [inline]
validate_xmit_skb+0x640/0xf30 net/core/dev.c:3104
__dev_queue_xmit+0xc14/0x3910 net/core/dev.c:3561
dev_queue_xmit+0x17/0x20 net/core/dev.c:3602
neigh_hh_output include/net/neighbour.h:473 [inline]
neigh_output include/net/neighbour.h:481 [inline]
ip_finish_output2+0x1063/0x1860 net/ipv4/ip_output.c:229
ip_finish_output+0x841/0xfa0 net/ipv4/ip_output.c:317
NF_HOOK_COND include/linux/netfilter.h:276 [inline]
ip_output+0x223/0x880 net/ipv4/ip_output.c:405
dst_output include/net/dst.h:444 [inline]
ip_local_out+0xc5/0x1b0 net/ipv4/ip_output.c:124
iptunnel_xmit+0x567/0x850 net/ipv4/ip_tunnel_core.c:91
ip_tunnel_xmit+0x1598/0x3af1 net/ipv4/ip_tunnel.c:778
ipip_tunnel_xmit+0x264/0x2c0 net/ipv4/ipip.c:308
__netdev_start_xmit include/linux/netdevice.h:4148 [inline]
netdev_start_xmit include/linux/netdevice.h:4157 [inline]
xmit_one net/core/dev.c:3034 [inline]
dev_hard_start_xmit+0x26c/0xc30 net/core/dev.c:3050
__dev_queue_xmit+0x29ef/0x3910 net/core/dev.c:3569
dev_queue_xmit+0x17/0x20 net/core/dev.c:3602
neigh_direct_output+0x15/0x20 net/core/neighbour.c:1403
neigh_output include/net/neighbour.h:483 [inline]
ip_finish_output2+0xa67/0x1860 net/ipv4/ip_output.c:229
ip_finish_output+0x841/0xfa0 net/ipv4/ip_output.c:317
NF_HOOK_COND include/linux/netfilter.h:276 [inline]
ip_output+0x223/0x880 net/ipv4/ip_output.c:405
dst_output include/net/dst.h:444 [inline]
ip_local_out+0xc5/0x1b0 net/ipv4/ip_output.c:124
ip_queue_xmit+0x9df/0x1f80 net/ipv4/ip_output.c:504
tcp_transmit_skb+0x1bf9/0x3f10 net/ipv4/tcp_output.c:1168
tcp_write_xmit+0x1641/0x5c20 net/ipv4/tcp_output.c:2363
__tcp_push_pending_frames+0xb2/0x290 net/ipv4/tcp_output.c:2536
tcp_push+0x638/0x8c0 net/ipv4/tcp.c:735
tcp_sendmsg_locked+0x2ec5/0x3f00 net/ipv4/tcp.c:1410
tcp_sendmsg+0x2f/0x50 net/ipv4/tcp.c:1447
inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798
sock_sendmsg_nosec net/socket.c:641 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:651
__sys_sendto+0x3d7/0x670 net/socket.c:1797
__do_sys_sendto net/socket.c:1809 [inline]
__se_sys_sendto net/socket.c:1805 [inline]
__x64_sys_sendto+0xe1/0x1a0 net/socket.c:1805
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x455ab9
Code: 1d ba fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb b9 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fcae64d5c68 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007fcae64d66d4 RCX: 0000000000455ab9
RDX: 0000000000000001 RSI: 0000000020000200 RDI: 0000000000000013
RBP: 000000000072bea0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000014
R13: 00000000004c1145 R14: 00000000004d1818 R15: 0000000000000006
Modules linked in:
Dumping ftrace buffer:
(ftrace buffer empty)
Fixes: ddff00d42043 ("net: Move skb_has_shared_frag check out of GRE code and into segmentation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Example setup:
host: ip -6 addr add dev eth1 2001:db8:104::4
where eth1 is enslaved to a VRF
switch: ip -6 ro add 2001:db8:104::4/128 dev br1
where br1 only has an LLA
ping6 2001:db8:104::4
ssh 2001:db8:104::4
(NOTE: UDP works fine if the PKTINFO has the address set to the global
address and ifindex is set to the index of eth1 with a destination an
LLA).
For ICMP, icmp6_iif needs to be updated to check if skb->dev is an
L3 master. If it is then return the ifindex from rt6i_idev similar
to what is done for loopback.
For TCP, restore the original tcp_v6_iif definition which is needed in
most places and add a new tcp_v6_iif_l3_slave that considers the
l3_slave variability. This latter check is only needed for socket
lookups.
Fixes: 9ff74384600a ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
- Fix interrupt type on ethernet switch for i.MX-based RDU2
- GPC on i.MX exposed too large a register window which resulted in
userspace being able to crash the machine.
- Fixup of bad merge resolution moving GPIO DT nodes under pinctrl on
droid4.
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: imx6: RDU2: fix irq type for mv88e6xxx switch
soc: imx: gpc: restrict register range for regmap access
ARM: dts: omap4-droid4: fix dts w.r.t. pwm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"A single fix for a MCE-polling regression, which prevented the
disabling of polling"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/MCE: Remove min interval polling limitation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 pti fixes from Ingo Molnar:
"An APM fix, and a BTS hardware-tracing fix related to PTI changes"
* 'x86-pti-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apm: Don't access __preempt_count with zeroed fs
x86/events/intel/ds: Fix bts_interrupt_threshold alignment
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Two fixes: a stop-machine preemption fix and a SCHED_DEADLINE fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Fix switched_from_dl() warning
stop_machine: Disable preemption when waking two stopper threads
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core kernel fixes from Ingo Molnar:
"This is mostly the copy_to_user_mcsafe() related fixes from Dan
Williams, and an ORC fix for Clang"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm/memcpy_mcsafe: Fix copy_to_user_mcsafe() exception handling
lib/iov_iter: Fix pipe handling in _copy_to_iter_mcsafe()
lib/iov_iter: Document _copy_to_iter_flushcache()
lib/iov_iter: Document _copy_to_iter_mcsafe()
objtool: Use '.strtab' if '.shstrtab' doesn't exist, to support ORC tables on Clang
|
