diff options
| -rw-r--r-- | Documentation/scsi/00-INDEX | 2 | ||||
| -rw-r--r-- | Documentation/scsi/scsi_eh.txt | 479 | ||||
| -rw-r--r-- | drivers/block/scsi_ioctl.c | 1 | ||||
| -rw-r--r-- | drivers/ieee1394/sbp2.c | 8 | ||||
| -rw-r--r-- | drivers/scsi/3w-9xxx.c | 30 | ||||
| -rw-r--r-- | drivers/scsi/Kconfig | 7 | ||||
| -rw-r--r-- | drivers/scsi/Makefile | 1 | ||||
| -rw-r--r-- | drivers/scsi/lpfc/lpfc_attr.c | 22 | ||||
| -rw-r--r-- | drivers/scsi/lpfc/lpfc_hbadisc.c | 7 | ||||
| -rw-r--r-- | drivers/scsi/lpfc/lpfc_hw.h | 17 | ||||
| -rw-r--r-- | drivers/scsi/lpfc/lpfc_init.c | 7 | ||||
| -rw-r--r-- | drivers/scsi/qla2xxx/qla_attr.c | 18 | ||||
| -rw-r--r-- | drivers/scsi/qla2xxx/qla_init.c | 4 | ||||
| -rw-r--r-- | drivers/scsi/scsi_lib.c | 138 | ||||
| -rw-r--r-- | drivers/scsi/scsi_priv.h | 1 | ||||
| -rw-r--r-- | drivers/scsi/scsi_scan.c | 88 | ||||
| -rw-r--r-- | drivers/scsi/scsi_sysfs.c | 28 | ||||
| -rw-r--r-- | drivers/scsi/scsi_transport_sas.c | 820 | ||||
| -rw-r--r-- | drivers/scsi/sg.c | 4 | ||||
| -rw-r--r-- | include/scsi/scsi_device.h | 4 | ||||
| -rw-r--r-- | include/scsi/scsi_transport_fc.h | 8 | ||||
| -rw-r--r-- | include/scsi/scsi_transport_sas.h | 100 |
22 files changed, 1648 insertions, 146 deletions
diff --git a/Documentation/scsi/00-INDEX b/Documentation/scsi/00-INDEX index f9cb5bdcce41..fef92ebf266f 100644 --- a/Documentation/scsi/00-INDEX +++ b/Documentation/scsi/00-INDEX @@ -60,6 +60,8 @@ scsi.txt - short blurb on using SCSI support as a module. scsi_mid_low_api.txt - info on API between SCSI layer and low level drivers +scsi_eh.txt + - info on SCSI midlayer error handling infrastructure st.txt - info on scsi tape driver sym53c500_cs.txt diff --git a/Documentation/scsi/scsi_eh.txt b/Documentation/scsi/scsi_eh.txt new file mode 100644 index 000000000000..534a50922a7b --- /dev/null +++ b/Documentation/scsi/scsi_eh.txt @@ -0,0 +1,479 @@ + +SCSI EH +====================================== + + This document describes SCSI midlayer error handling infrastructure. +Please refer to Documentation/scsi/scsi_mid_low_api.txt for more +information regarding SCSI midlayer. + +TABLE OF CONTENTS + +[1] How SCSI commands travel through the midlayer and to EH + [1-1] struct scsi_cmnd + [1-2] How do scmd's get completed? + [1-2-1] Completing a scmd w/ scsi_done + [1-2-2] Completing a scmd w/ timeout + [1-3] How EH takes over +[2] How SCSI EH works + [2-1] EH through fine-grained callbacks + [2-1-1] Overview + [2-1-2] Flow of scmds through EH + [2-1-3] Flow of control + [2-2] EH through hostt->eh_strategy_handler() + [2-2-1] Pre hostt->eh_strategy_handler() SCSI midlayer conditions + [2-2-2] Post hostt->eh_strategy_handler() SCSI midlayer conditions + [2-2-3] Things to consider + + +[1] How SCSI commands travel through the midlayer and to EH + +[1-1] struct scsi_cmnd + + Each SCSI command is represented with struct scsi_cmnd (== scmd). A +scmd has two list_head's to link itself into lists. The two are +scmd->list and scmd->eh_entry. The former is used for free list or +per-device allocated scmd list and not of much interest to this EH +discussion. The latter is used for completion and EH lists and unless +otherwise stated scmds are always linked using scmd->eh_entry in this +discussion. + + +[1-2] How do scmd's get completed? + + Once LLDD gets hold of a scmd, either the LLDD will complete the +command by calling scsi_done callback passed from midlayer when +invoking hostt->queuecommand() or SCSI midlayer will time it out. + + +[1-2-1] Completing a scmd w/ scsi_done + + For all non-EH commands, scsi_done() is the completion callback. It +does the following. + + 1. Delete timeout timer. If it fails, it means that timeout timer + has expired and is going to finish the command. Just return. + + 2. Link scmd to per-cpu scsi_done_q using scmd->en_entry + + 3. Raise SCSI_SOFTIRQ + + SCSI_SOFTIRQ handler scsi_softirq calls scsi_decide_disposition() to +determine what to do with the command. scsi_decide_disposition() +looks at the scmd->result value and sense data to determine what to do +with the command. + + - SUCCESS + scsi_finish_command() is invoked for the command. The + function does some maintenance choirs and notify completion by + calling scmd->done() callback, which, for fs requests, would + be HLD completion callback - sd:sd_rw_intr, sr:rw_intr, + st:st_intr. + + - NEEDS_RETRY + - ADD_TO_MLQUEUE + scmd is requeued to blk queue. + + - otherwise + scsi_eh_scmd_add(scmd, 0) is invoked for the command. See + [1-3] for details of this funciton. + + +[1-2-2] Completing a scmd w/ timeout + + The timeout handler is scsi_times_out(). When a timeout occurs, this +function + + 1. invokes optional hostt->eh_timedout() callback. Return value can + be one of + + - EH_HANDLED + This indicates that eh_timedout() dealt with the timeout. The + scmd is passed to __scsi_done() and thus linked into per-cpu + scsi_done_q. Normal command completion described in [1-2-1] + follows. + + - EH_RESET_TIMER + This indicates that more time is required to finish the + command. Timer is restarted. This action is counted as a + retry and only allowed scmd->allowed + 1(!) times. Once the + limit is reached, action for EH_NOT_HANDLED is taken instead. + + *NOTE* This action is racy as the LLDD could finish the scmd + after the timeout has expired but before it's added back. In + such cases, scsi_done() would think that timeout has occurred + and return without doing anything. We lose completion and the + command will time out again. + + - EH_NOT_HANDLED + This is the same as when eh_timedout() callback doesn't exist. + Step #2 is taken. + + 2. scsi_eh_scmd_add(scmd, SCSI_EH_CANCEL_CMD) is invoked for the + command. See [1-3] for more information. + + +[1-3] How EH takes over + + scmds enter EH via scsi_eh_scmd_add(), which does the following. + + 1. Turns on scmd->eh_eflags as requested. It's 0 for error + completions and SCSI_EH_CANCEL_CMD for timeouts. + + 2. Links scmd->eh_entry to shost->eh_cmd_q + + 3. Sets SHOST_RECOVERY bit in shost->shost_state + + 4. Increments shost->host_failed + + 5. Wakes up SCSI EH thread if shost->host_busy == shost->host_failed + + As can be seen above, once any scmd is added to shost->eh_cmd_q, +SHOST_RECOVERY shost_state bit is turned on. This prevents any new +scmd to be issued from blk queue to the host; eventually, all scmds on +the host either complete normally, fail and get added to eh_cmd_q, or +time out and get added to shost->eh_cmd_q. + + If all scmds either complete or fail, the number of in-flight scmds +becomes equal to the number of failed scmds - i.e. shost->host_busy == +shost->host_failed. This wakes up SCSI EH thread. So, once woken up, +SCSI EH thread can expect that all in-flight commands have failed and +are linked on shost->eh_cmd_q. + + Note that this does not mean lower layers are quiescent. If a LLDD +completed a scmd with error status, the LLDD and lower layers are +assumed to forget about the scmd at that point. However, if a scmd +has timed out, unless hostt->eh_timedout() made lower layers forget +about the scmd, which currently no LLDD does, the command is still +active as long as lower layers are concerned and completion could +occur at any time. Of course, all such completions are ignored as the +timer has already expired. + + We'll talk about how SCSI EH takes actions to abort - make LLDD +forget about - timed out scmds later. + + +[2] How SCSI EH works + + LLDD's can implement SCSI EH actions in one of the following two +ways. + + - Fine-grained EH callbacks + LLDD can implement fine-grained EH callbacks and let SCSI + midlayer drive error handling and call appropriate callbacks. + This will be dicussed further in [2-1]. + + - eh_strategy_handler() callback + This is one big callback which should perform whole error + handling. As such, it should do all choirs SCSI midlayer + performs during recovery. This will be discussed in [2-2]. + + Once recovery is complete, SCSI EH resumes normal operation by +calling scsi_restart_operations(), which + + 1. Checks if door locking is needed and locks door. + + 2. Clears SHOST_RECOVERY shost_state bit + + 3. Wakes up waiters on shost->host_wait. This occurs if someone + calls scsi_block_when_processing_errors() on the host. + (*QUESTION* why is it needed? All operations will be blocked + anyway after it reaches blk queue.) + + 4. Kicks queues in all devices on the host in the asses + + +[2-1] EH through fine-grained callbacks + +[2-1-1] Overview + + If eh_strategy_handler() is not present, SCSI midlayer takes charge +of driving error handling. EH's goals are two - make LLDD, host and +device forget about timed out scmds and make them ready for new +commands. A scmd is said to be recovered if the scmd is forgotten by +lower layers and lower layers are ready to process or fail the scmd +again. + + To achieve these goals, EH performs recovery actions with increasing +severity. Some actions are performed by issueing SCSI commands and +others are performed by invoking one of the following fine-grained +hostt EH callbacks. Callbacks may be omitted and omitted ones are +considered to fail always. + +int (* eh_abort_handler)(struct scsi_cmnd *); +int (* eh_device_reset_handler)(struct scsi_cmnd *); +int (* eh_bus_reset_handler)(struct scsi_cmnd *); +int (* eh_host_reset_handler)(struct scsi_cmnd *); + + Higher-severity actions are taken only when lower-severity actions +cannot recover some of failed scmds. Also, note that failure of the +highest-severity action means EH failure and results in offlining of +all unrecovered devices. + + During recovery, the following rules are followed + + - Recovery actions are performed on failed scmds on the to do list, + eh_work_q. If a recovery action succeeds for a scmd, recovered + scmds are removed from eh_work_q. + + Note that single recovery action on a scmd can recover multiple + scmds. e.g. resetting a device recovers all failed scmds on the + device. + + - Higher severity actions are taken iff eh_work_q is not empty after + lower severity actions are complete. + + - EH reuses failed scmds to issue commands for recovery. For + timed-out scmds, SCSI EH ensures that LLDD forgets about a scmd + before reusing it for EH commands. + + When a scmd is recovered, the scmd is moved from eh_work_q to EH +local eh_done_q using scsi_eh_finish_cmd(). After all scmds are +recovered (eh_work_q is empty), scsi_eh_flush_done_q() is invoked to +either retry or error-finish (notify upper layer of failure) recovered +scmds. + + scmds are retried iff its sdev is still online (not offlined during +EH), REQ_FAILFAST is not set and ++scmd->retries is less than +scmd->allowed. + + +[2-1-2] Flow of scmds through EH + + 1. Error completion / time out + ACTION: scsi_eh_scmd_add() is invoked for scmd + - set scmd->eh_eflags + - add scmd to shost->eh_cmd_q + - set SHOST_RECOVERY + - shost->host_failed++ + LOCKING: shost->host_lock + + 2. EH starts + ACTION: move all scmds to EH's local eh_work_q. shost->eh_cmd_q + is cleared. + LOCKING: shost->host_lock (not strictly necessary, just for + consistency) + + 3. scmd recovered + ACTION: scsi_eh_finish_cmd() is invoked to EH-finish scmd + - shost->host_failed-- + - clear scmd->eh_eflags + - scsi_setup_cmd_retry() + - move from local eh_work_q to local eh_done_q + LOCKING: none + + 4. EH completes + ACTION: scsi_eh_flush_done_q() retries scmds or notifies upper + layer of failure. + - scmd is removed from eh_done_q and scmd->eh_entry is cleared + - if retry is necessary, scmd is requeued using + scsi_queue_insert() + - otherwise, scsi_finish_command() is invoked for scmd + LOCKING: queue or finish function performs appropriate locking + + +[2-1-3] Flow of control + + EH through fine-grained callbacks start from scsi_unjam_host(). + +<<scsi_unjam_host>> + + 1. Lock shost->host_lock, splice_init shost->eh_cmd_q into local + eh_work_q and unlock host_lock. Note that shost->eh_cmd_q is + cleared by this action. + + 2. Invoke scsi_eh_get_sense. + + <<scsi_eh_get_sense>> + + This action is taken for each error-completed + (!SCSI_EH_CANCEL_CMD) commands without valid sense data. Most + SCSI transports/LLDDs automatically acquire sense data on + command failures (autosense). Autosense is recommended for + performance reasons and as sense information could get out of + sync inbetween occurrence of CHECK CONDITION and this action. + + Note that if autosense is not supported, scmd->sense_buffer + contains invalid sense data when error-completing the scmd + with scsi_done(). scsi_decide_disposition() always returns + FAILED in such cases thus invoking SCSI EH. When the scmd + reaches here, sense data is acquired and + scsi_decide_disposition() is called again. + + 1. Invoke scsi_request_sense() which issues REQUEST_SENSE + command. If fails, no action. Note that taking no action + causes higher-severity recovery to be taken for the scmd. + + 2. Invoke scsi_decide_disposition() on the scmd + + - SUCCESS + scmd->retries is set to scmd->allowed preventing + scsi_eh_flush_done_q() from retrying the scmd and + scsi_eh_finish_cmd() is invoked. + + - NEEDS_RETRY + scsi_eh_finish_cmd() invoked + + - otherwise + No action. + + 3. If !list_empty(&eh_work_q), invoke scsi_eh_abort_cmds(). + + <<scsi_eh_abort_cmds>> + + This action is taken for each timed out command. + hostt->eh_abort_handler() is invoked for each scmd. The + handler returns SUCCESS if it has succeeded to make LLDD and + all related hardware forget about the scmd. + + If a timedout scmd is successfully aborted and the sdev is + either offline or ready, scsi_eh_finish_cmd() is invoked for + the scmd. Otherwise, the scmd is left in eh_work_q for + higher-severity actions. + + Note that both offline and ready status mean that the sdev is + ready to process new scmds, where processing also implies + immediate failing; thus, if a sdev is in one of the two + states, no further recovery action is needed. + + Device readiness is tested using scsi_eh_tur() which issues + TEST_UNIT_READY command. Note that the scmd must have been + aborted successfully before reusing it for TEST_UNIT_READY. + + 4. If !list_empty(&eh_work_q), invoke scsi_eh_ready_devs() + + <<scsi_eh_ready_devs>> + + This function takes four increasingly more severe measures to + make failed sdevs ready for new commands. + + 1. Invoke scsi_eh_stu() + + <<scsi_eh_stu>> + + For each sdev which has failed scmds with valid sense data + of which scsi_check_sense()'s verdict is FAILED, + START_STOP_UNIT command is issued w/ start=1. Note that + as we explicitly choose error-completed scmds, it is known + that lower layers have forgotten about the scmd and we can + reuse it for STU. + + If STU succeeds and the sdev is either offline or ready, + all failed scmds on the sdev are EH-finished with + scsi_eh_finish_cmd(). + + *NOTE* If hostt->eh_abort_handler() isn't implemented or + failed, we may still have timed out scmds at this point + and STU doesn't make lower layers forget about those + scmds. Yet, this function EH-finish all scmds on the sdev + if STU succeeds leaving lower layers in an inconsistent + state. It seems that STU action should be taken only when + a sdev has no timed out scmd. + + 2. If !list_empty(&eh_work_q), invoke scsi_eh_bus_device_reset(). + + <<scsi_eh_bus_device_reset>> + + This action is very similar to scsi_eh_stu() except that, + instead of issuing STU, hostt->eh_device_reset_handler() + is used. Also, as we're not issuing SCSI commands and + resetting clears all scmds on the sdev, there is no need + to choose error-completed scmds. + + 3. If !list_empty(&eh_work_q), invoke scsi_eh_bus_reset() + + <<scsi_eh_bus_reset>> + + hostt->eh_bus_reset_handler() is invoked for each channel + with failed scmds. If bus reset succeeds, all failed + scmds on all ready or offline sdevs on the channel are + EH-finished. + + 4. If !list_empty(&eh_work_q), invoke scsi_eh_host_reset() + + <<scsi_eh_host_reset>> + + This is the last resort. hostt->eh_host_reset_handler() + is invoked. If host reset succeeds, all failed scmds on + all ready or offline sdevs on the host are EH-finished. + + 5. If !list_empty(&eh_work_q), invoke scsi_eh_offline_sdevs() + + <<scsi_eh_offline_sdevs>> + + Take all sdevs which still have unrecovered scmds offline + and EH-finish the scmds. + + 5. Invoke scsi_eh_flush_done_q(). + + <<scsi_eh_flush_done_q>> + + At this point all scmds are recovered (or given up) and + put on eh_done_q by scsi_eh_finish_cmd(). This function + flushes eh_done_q by either retrying or notifying upper + layer of failure of the scmds. + + +[2-2] EH through hostt->eh_strategy_handler() + + hostt->eh_strategy_handler() is invoked in the place of +scsi_unjam_host() and it is responsible for whole recovery process. +On completion, the handler should have made lower layers forget about +all failed scmds and either ready for new commands or offline. Also, +it should perform SCSI EH maintenance choirs to maintain integrity of +SCSI midlayer. IOW, of the steps described in [2-1-2], all steps +except for #1 must be implemented by eh_strategy_handler(). + + +[2-2-1] Pre hostt->eh_strategy_handler() SCSI midlayer conditions + + The following conditions are true on entry to the handler. + + - Each failed scmd's eh_flags field is set appropriately. + + - Each failed scmd is linked on scmd->eh_cmd_q by scmd->eh_entry. + + - SHOST_RECOVERY is set. + + - shost->host_failed == shost->host_busy + + +[2-2-2] Post hostt->eh_strategy_handler() SCSI midlayer conditions + + The following conditions must be true on exit from the handler. + + - shost->host_failed is zero. + + - Each scmd's eh_eflags field is cleared. + + - Each scmd is in such a state that scsi_setup_cmd_retry() on the + scmd doesn't make any difference. + + - shost->eh_cmd_q is cleared. + + - Each scmd->eh_entry is cleared. + + - Either scsi_queue_insert() or scsi_finish_command() is called on + each scmd. Note that the handler is free to use scmd->retries and + ->allowed to limit the number of retries. + + +[2-2-3] Things to consider + + - Know that timed out scmds are still active on lower layers. Make + lower layers forget about them before doing anything else with + those scmds. + + - For consistency, when accessing/modifying shost data structure, + grab shost->host_lock. + + - On completion, each failed sdev must have forgotten about all + active scmds. + + - On completion, each failed sdev must be ready for new commands or + offline. + + +-- +Tejun Heo +htejun@gmail.com +11th September 2005 diff --git a/drivers/block/scsi_ioctl.c b/drivers/block/scsi_ioctl.c index abb2df249fd3..856c2278e9d0 100644 --- a/drivers/block/scsi_ioctl.c +++ b/drivers/block/scsi_ioctl.c @@ -123,6 +123,7 @@ static int verify_command(struct file *file, unsigned char *cmd) safe_for_read(READ_12), safe_for_read(READ_16), safe_for_read(READ_BUFFER), + safe_for_read(READ_DEFECT_DATA), safe_for_read(READ_LONG), safe_for_read(INQUIRY), safe_for_read(MODE_SENSE), diff --git a/drivers/ieee1394/sbp2.c b/drivers/ieee1394/sbp2.c index 627af507643a..de88218ef7cc 100644 --- a/drivers/ieee1394/sbp2.c +++ b/drivers/ieee1394/sbp2.c @@ -790,7 +790,7 @@ static void sbp2_host_reset(struct hpsb_host *host) static int sbp2_start_device(struct scsi_id_instance_data *scsi_id) { struct sbp2scsi_host_info *hi = scsi_id->hi; - struct scsi_device *sdev; + int error; SBP2_DEBUG("sbp2_start_device"); @@ -939,10 +939,10 @@ alloc_fail: sbp2_max_speed_and_size(scsi_id); /* Add this device to the scsi layer now */ - sdev = scsi_add_device(scsi_id->scsi_host, 0, scsi_id->ud->id, 0); - if (IS_ERR(sdev)) { + error = scsi_add_device(scsi_id->scsi_host, 0, scsi_id->ud->id, 0); + if (error) { SBP2_ERR("scsi_add_device failed"); - return PTR_ERR(sdev); + return error; } return 0; diff --git a/drivers/scsi/3w-9xxx.c b/drivers/scsi/3w-9xxx.c index bc6e4627c7a1..a6ac61611f35 100644 --- a/drivers/scsi/3w-9xxx.c +++ b/drivers/scsi/3w-9xxx.c @@ -59,6 +59,7 @@ Fix 'handled=1' ISR usage, remove bogus IRQ check. Remove un-needed eh_abort handler. Add support for embedded firmware error strings. + 2.26.02.003 - Correctly handle single sgl's with use_sg=1. */ #include <linux/module.h> @@ -81,7 +82,7 @@ #include "3w-9xxx.h" /* Globals */ -#define TW_DRIVER_VERSION "2.26.02.002" +#define TW_DRIVER_VERSION "2.26.02.003" static TW_Device_Extension *twa_device_extension_list[TW_MAX_SLOT]; static unsigned int twa_device_extension_count; static int twa_major = -1; @@ -1805,6 +1806,8 @@ static int twa_scsiop_execute_scsi(TW_Device_Extension *tw_dev, int request_id, if (tw_dev->srb[request_id]->request_bufflen < TW_MIN_SGL_LENGTH) { command_packet->sg_list[0].address = tw_dev->generic_buffer_phys[request_id]; command_packet->sg_list[0].length = TW_MIN_SGL_LENGTH; + if (tw_dev->srb[request_id]->sc_data_direction == DMA_TO_DEVICE || tw_dev->srb[request_id]->sc_data_direction == DMA_BIDIRECTIONAL) + memcpy(tw_dev->generic_buffer_virt[request_id], tw_dev->srb[request_id]->request_buffer, tw_dev->srb[request_id]->request_bufflen); } else { buffaddr = twa_map_scsi_single_data(tw_dev, request_id); if (buffaddr == 0) @@ -1823,6 +1826,12 @@ static int twa_scsiop_execute_scsi(TW_Device_Extension *tw_dev, int request_id, if (tw_dev->srb[request_id]->use_sg > 0) { if ((tw_dev->srb[request_id]->use_sg == 1) && (tw_dev->srb[request_id]->request_bufflen < TW_MIN_SGL_LENGTH)) { + if (tw_dev->srb[request_id]->sc_data_direction == DMA_TO_DEVICE || tw_dev->srb[request_id]->sc_data_direction == DMA_BIDIRECTIONAL) { + struct scatterlist *sg = (struct scatterlist *)tw_dev->srb[request_id]->request_buffer; + char *buf = kmap_atomic(sg->page, KM_IRQ0) + sg->offset; + memcpy(tw_dev->generic_buffer_virt[request_id], buf, sg->length); + kunmap_atomic(buf - sg->offset, KM_IRQ0); + } command_packet->sg_list[0].address = tw_dev->generic_buffer_phys[request_id]; command_packet->sg_list[0].length = TW_MIN_SGL_LENGTH; } else { @@ -1888,11 +1897,20 @@ out: /* This function completes an execute scsi operation */ static void twa_scsiop_execute_scsi_complete(TW_Device_Extension *tw_dev, int request_id) { - /* Copy the response if too small */ - if ((tw_dev->srb[request_id]->request_buffer) && (tw_dev->srb[request_id]->request_bufflen < TW_MIN_SGL_LENGTH)) { - memcpy(tw_dev->srb[request_id]->request_buffer, - tw_dev->generic_buffer_virt[request_id], - tw_dev->srb[request_id]->request_bufflen); + if (tw_dev->srb[request_id]->request_bufflen < TW_MIN_SGL_LENGTH && + (tw_dev->srb[request_id]->sc_data_direction == DMA_FROM_DEVICE || + tw_dev->srb[request_id]->sc_data_direction == DMA_BIDIRECTIONAL)) { + if (tw_dev->srb[request_id]->use_sg == 0) { + memcpy(tw_dev->srb[request_id]->request_buffer, + tw_dev->generic_buffer_virt[request_id], + tw_dev->srb[request_id]->request_bufflen); + } + if (tw_dev->srb[request_id]->use_sg == 1) { + struct scatterlist *sg = (struct scatterlist *)tw_dev->srb[request_id]->request_buffer; + char *buf = kmap_atomic(sg->page, KM_IRQ0) + sg->offset; + memcpy(buf, tw_dev->generic_buffer_virt[request_id], sg->length); + kunmap_atomic(buf - sg->offset, KM_IRQ0); + } } } /* End twa_scsiop_execute_scsi_complete() */ diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig index 2d21265e650b..20019b82b4a8 100644 --- a/drivers/scsi/Kconfig +++ b/drivers/scsi/Kconfig @@ -235,6 +235,13 @@ config SCSI_ISCSI_ATTRS each attached iSCSI device to sysfs, say Y. Otherwise, say N. +config SCSI_SAS_ATTRS + tristate "SAS Transport Attributes" + depends on SCSI + help + If you wish to export transport-specific information about + each attached SAS device to sysfs, say Y. + endmenu menu "SCSI low-level drivers" diff --git a/drivers/scsi/Makefile b/drivers/scsi/Makefile index 4b4fd94c2674..1e4edbdf2730 100644 --- a/drivers/scsi/Makefile +++ b/drivers/scsi/Makefile @@ -31,6 +31,7 @@ obj-$(CONFIG_RAID_ATTRS) += raid_class.o obj-$(CONFIG_SCSI_SPI_ATTRS) += scsi_transport_spi.o obj-$(CONFIG_SCSI_FC_ATTRS) += scsi_transport_fc.o obj-$(CONFIG_SCSI_ISCSI_ATTRS) += scsi_transport_iscsi.o +obj-$(CONFIG_SCSI_SAS_ATTRS) += scsi_transport_sas.o obj-$(CONFIG_SCSI_AMIGA7XX) += amiga7xx.o 53c7xx.o obj-$(CONFIG_A3000_SCSI) += a3000.o wd33c93.o diff --git a/drivers/scsi/lpfc/lpfc_attr.c b/drivers/scsi/lpfc/lpfc_attr.c index 0e089a42c03a..86eaf6d408d5 100644 --- a/drivers/scsi/lpfc/lpfc_attr.c +++ b/drivers/scsi/lpfc/lpfc_attr.c @@ -966,21 +966,21 @@ static void lpfc_get_host_fabric_name (struct Scsi_Host *shost) { struct lpfc_hba *phba = (struct lpfc_hba*)shost->hostdata[0]; - u64 nodename; + u64 node_name; spin_lock_irq(shost->host_lock); if ((phba->fc_flag & FC_FABRIC) || ((phba->fc_topology == TOPOLOGY_LOOP) && (phba->fc_flag & FC_PUBLIC_LOOP))) - memcpy(&nodename, &phba->fc_fabparam.nodeName, sizeof(u64)); + node_name = wwn_to_u64(phba->fc_fabparam.nodeName.wwn); else /* fabric is local port if there is no F/FL_Port */ - memcpy(&nodename, &phba->fc_nodename, sizeof(u64)); + node_name = wwn_to_u64(phba->fc_nodename.wwn); spin_unlock_irq(shost->host_lock); - fc_host_fabric_name(shost) = be64_to_cpu(nodename); + fc_host_fabric_name(shost) = node_name; } @@ -1103,21 +1103,20 @@ lpfc_get_starget_node_name(struct scsi_target *starget) { struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); struct lpfc_hba *phba = (struct lpfc_hba *) shost->hostdata[0]; - uint64_t node_name = 0; + u64 node_name = 0; struct lpfc_nodelist *ndlp = NULL; spin_lock_irq(shost->host_lock); /* Search the mapped list for this target ID */ list_for_each_entry(ndlp, &phba->fc_nlpmap_list, nlp_listp) { if (starget->id == ndlp->nlp_sid) { - memcpy(&node_name, &ndlp->nlp_nodename, - sizeof(struct lpfc_name)); + node_name = wwn_to_u64(ndlp->nlp_nodename.wwn); break; } } spin_unlock_irq(shost->host_lock); - fc_starget_node_name(starget) = be64_to_cpu(node_name); + fc_starget_node_name(starget) = node_name; } static void @@ -1125,21 +1124,20 @@ lpfc_get_starget_port_name(struct scsi_target *starget) { struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); struct lpfc_hba *phba = (struct lpfc_hba *) shost->hostdata[0]; - uint64_t port_name = 0; + u64 port_name = 0; struct lpfc_nodelist *ndlp = NULL; spin_lock_irq(shost->host_lock); /* Search the mapped list for this target ID */ list_for_each_entry(ndlp, &phba->fc_nlpmap_list, nlp_listp) { if (starget->id == ndlp->nlp_sid) { - memcpy(&port_name, &ndlp->nlp_portname, - sizeof(struct lpfc_name)); + port_name = wwn_to_u64(ndlp->nlp_portname.wwn); break; } } spin_unlock_irq(shost->host_lock); - fc_starget_port_name(starget) = be64_to_cpu(port_name); + fc_starget_port_name(starget) = port_name; } static void diff --git a/drivers/scsi/lpfc/lpfc_hbadisc.c b/drivers/scsi/lpfc/lpfc_hbadisc.c index 0a8269d6b130..4fb8eb0c84cf 100644 --- a/drivers/scsi/lpfc/lpfc_hbadisc.c +++ b/drivers/scsi/lpfc/lpfc_hbadisc.c @@ -1017,13 +1017,10 @@ lpfc_register_remote_port(struct lpfc_hba * phba, struct fc_rport *rport; struct lpfc_rport_data *rdata; struct fc_rport_identifiers rport_ids; - uint64_t wwn; /* Remote port has reappeared. Re-register w/ FC transport */ - memcpy(&wwn, &ndlp->nlp_nodename, sizeof(uint64_t)); - rport_ids.node_name = be64_to_cpu(wwn); - memcpy(&wwn, &ndlp->nlp_portname, sizeof(uint64_t)); - rport_ids.port_name = be64_to_cpu(wwn); + rport_ids.node_name = wwn_to_u64(ndlp->nlp_nodename.wwn); + rport_ids.port_name = wwn_to_u64(ndlp->nlp_portname.wwn); rport_ids.port_id = ndlp->nlp_DID; rport_ids.roles = FC_RPORT_ROLE_UNKNOWN; if (ndlp->nlp_type & NLP_FCP_TARGET) diff --git a/drivers/scsi/lpfc/lpfc_hw.h b/drivers/scsi/lpfc/lpfc_hw.h index 21591cb9f551..047a87c26cc0 100644 --- a/drivers/scsi/lpfc/lpfc_hw.h +++ b/drivers/scsi/lpfc/lpfc_hw.h @@ -262,12 +262,14 @@ struct lpfc_sli_ct_request { #define FF_FRAME_SIZE 2048 struct lpfc_name { + union { + struct { #ifdef __BIG_ENDIAN_BITFIELD - uint8_t nameType:4; /* FC Word 0, bit 28:31 */ - uint8_t IEEEextMsn:4; /* FC Word 0, bit 24:27, bit 8:11 of IEEE ext */ + uint8_t nameType:4; /* FC Word 0, bit 28:31 */ + uint8_t IEEEextMsn:4; /* FC Word 0, bit 24:27, bit 8:11 of IEEE ext */ #else /* __LITTLE_ENDIAN_BITFIELD */ - uint8_t IEEEextMsn:4; /* FC Word 0, bit 24:27, bit 8:11 of IEEE ext */ - uint8_t nameType:4; /* FC Word 0, bit 28:31 */ + uint8_t IEEEextMsn:4; /* FC Word 0, bit 24:27, bit 8:11 of IEEE ext */ + uint8_t nameType:4; /* FC Word 0, bit 28:31 */ #endif #define NAME_IEEE 0x1 /* IEEE name - nameType */ @@ -276,8 +278,11 @@ struct lpfc_name { #define NAME_IP_TYPE 0x4 /* IP address */ #define NAME_CCITT_TYPE 0xC #define NAME_CCITT_GR_TYPE 0xE - uint8_t IEEEextLsb; /* FC Word 0, bit 16:23, IEEE extended Lsb */ - uint8_t IEEE[6]; /* FC IEEE address */ + uint8_t IEEEextLsb; /* FC Word 0, bit 16:23, IEEE extended Lsb */ + uint8_t IEEE[6]; /* FC IEEE address */ + }; + uint8_t wwn[8]; + }; }; struct csp { diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c index 6f3cb59bf9e0..454058f655db 100644 --- a/drivers/scsi/lpfc/lpfc_init.c +++ b/drivers/scsi/lpfc/lpfc_init.c @@ -1333,7 +1333,6 @@ lpfc_pci_probe_one(struct pci_dev *pdev, const struct pci_device_id *pid) unsigned long bar0map_len, bar2map_len; int error = -ENODEV, retval; int i; - u64 wwname; if (pci_enable_device(pdev)) goto out; @@ -1524,10 +1523,8 @@ lpfc_pci_probe_one(struct pci_dev *pdev, const struct pci_device_id *pid) * Must done after lpfc_sli_hba_setup() */ - memcpy(&wwname, &phba->fc_nodename, sizeof(u64)); - fc_host_node_name(host) = be64_to_cpu(wwname); - memcpy(&wwname, &phba->fc_portname, sizeof(u64)); - fc_host_port_name(host) = be64_to_cpu(wwname); + fc_host_node_name(host) = wwn_to_u64(phba->fc_nodename.wwn); + fc_host_port_name(host) = wwn_to_u64(phba->fc_portname.wwn); fc_host_supported_classes(host) = FC_COS_CLASS3; memset(fc_host_supported_fc4s(host), 0, diff --git a/drivers/scsi/qla2xxx/qla_attr.c b/drivers/scsi/qla2xxx/qla_attr.c index fe0fce71adc7..fc25cd834668 100644 --- a/drivers/scsi/qla2xxx/qla_attr.c +++ b/drivers/scsi/qla2xxx/qla_attr.c @@ -360,16 +360,16 @@ qla2x00_get_starget_node_name(struct scsi_target *starget) struct Scsi_Host *host = dev_to_shost(starget->dev.parent); scsi_qla_host_t *ha = to_qla_host(host); fc_port_t *fcport; - uint64_t node_name = 0; + u64 node_name = 0; list_for_each_entry(fcport, &ha->fcports, list) { if (starget->id == fcport->os_target_id) { - node_name = *(uint64_t *)fcport->node_name; + node_name = wwn_to_u64(fcport->node_name); break; } } - fc_starget_node_name(starget) = be64_to_cpu(node_name); + fc_starget_node_name(starget) = node_name; } static void @@ -378,16 +378,16 @@ qla2x00_get_starget_port_name(struct scsi_target *starget) struct Scsi_Host *host = dev_to_shost(starget->dev.parent); scsi_qla_host_t *ha = to_qla_host(host); fc_port_t *fcport; - uint64_t port_name = 0; + u64 port_name = 0; list_for_each_entry(fcport, &ha->fcports, list) { if (starget->id == fcport->os_target_id) { - port_name = *(uint64_t *)fcport->port_name; + port_name = wwn_to_u64(fcport->port_name); break; } } - fc_starget_port_name(starget) = be64_to_cpu(port_name); + fc_starget_port_name(starget) = port_name; } static void @@ -460,9 +460,7 @@ struct fc_function_template qla2xxx_transport_functions = { void qla2x00_init_host_attr(scsi_qla_host_t *ha) { - fc_host_node_name(ha->host) = - be64_to_cpu(*(uint64_t *)ha->init_cb->node_name); - fc_host_port_name(ha->host) = - be64_to_cpu(*(uint64_t *)ha->init_cb->port_name); + fc_host_node_name(ha->host) = wwn_to_u64(ha->init_cb->node_name); + fc_host_port_name(ha->host) = wwn_to_u64(ha->init_cb->port_name); fc_host_supported_classes(ha->host) = FC_COS_CLASS3; } diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c index c619583e646b..3e9b64137873 100644 --- a/drivers/scsi/qla2xxx/qla_init.c +++ b/drivers/scsi/qla2xxx/qla_init.c @@ -2066,8 +2066,8 @@ qla2x00_reg_remote_port(scsi_qla_host_t *ha, fc_port_t *fcport) return; } - rport_ids.node_name = be64_to_cpu(*(uint64_t *)fcport->node_name); - rport_ids.port_name = be64_to_cpu(*(uint64_t *)fcport->port_name); + rport_ids.node_name = wwn_to_u64(fcport->node_name); + rport_ids.port_name = wwn_to_u64(fcport->port_name); rport_ids.port_id = fcport->d_id.b.domain << 16 | fcport->d_id.b.area << 8 | fcport->d_id.b.al_pa; rport_ids.roles = FC_RPORT_ROLE_UNKNOWN; diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c index 77f2d444f7e0..863bb6495daa 100644 --- a/drivers/scsi/scsi_lib.c +++ b/drivers/scsi/scsi_lib.c @@ -97,6 +97,30 @@ int scsi_insert_special_req(struct scsi_request *sreq, int at_head) } static void scsi_run_queue(struct request_queue *q); +static void scsi_release_buffers(struct scsi_cmnd *cmd); + +/* + * Function: scsi_unprep_request() + * + * Purpose: Remove all preparation done for a request, including its + * associated scsi_cmnd, so that it can be requeued. + * + * Arguments: req - request to unprepare + * + * Lock status: Assumed that no locks are held upon entry. + * + * Returns: Nothing. + */ +static void scsi_unprep_request(struct request *req) +{ + struct scsi_cmnd *cmd = req->special; + + req->flags &= ~REQ_DONTPREP; + req->special = (req->flags & REQ_SPECIAL) ? cmd->sc_request : NULL; + + scsi_release_buffers(cmd); + scsi_put_command(cmd); +} /* * Function: scsi_queue_insert() @@ -116,12 +140,14 @@ static void scsi_run_queue(struct request_queue *q); * commands. * Notes: This could be called either from an interrupt context or a * normal process context. + * Notes: Upon return, cmd is a stale pointer. */ int scsi_queue_insert(struct scsi_cmnd *cmd, int reason) { struct Scsi_Host *host = cmd->device->host; struct scsi_device *device = cmd->device; struct request_queue *q = device->request_queue; + struct request *req = cmd->request; unsigned long flags; SCSI_LOG_MLQUEUE(1, @@ -162,8 +188,9 @@ int scsi_queue_insert(struct scsi_cmnd *cmd, int reason) * function. The SCSI request function detects the blocked condition * and plugs the queue appropriately. */ + scsi_unprep_request(req); spin_lock_irqsave(q->queue_lock, flags); - blk_requeue_request(q, cmd->request); + blk_requeue_request(q, req); spin_unlock_irqrestore(q->queue_lock, flags); scsi_run_queue(q); @@ -339,7 +366,7 @@ int scsi_execute_req(struct scsi_device *sdev, const unsigned char *cmd, int result; if (sshdr) { - sense = kmalloc(SCSI_SENSE_BUFFERSIZE, GFP_KERNEL); + sense = kmalloc(SCSI_SENSE_BUFFERSIZE, GFP_NOIO); if (!sense) return DRIVER_ERROR << 24; memset(sense, 0, SCSI_SENSE_BUFFERSIZE); @@ -552,15 +579,16 @@ static void scsi_run_queue(struct request_queue *q) * I/O errors in the middle of the request, in which case * we need to request the blocks that come after the bad * sector. + * Notes: Upon return, cmd is a stale pointer. */ static void scsi_requeue_command(struct request_queue *q, struct scsi_cmnd *cmd) { + struct request *req = cmd->request; unsigned long flags; - cmd->request->flags &= ~REQ_DONTPREP; - + scsi_unprep_request(req); spin_lock_irqsave(q->queue_lock, flags); - blk_requeue_request(q, cmd->request); + blk_requeue_request(q, req); spin_unlock_irqrestore(q->queue_lock, flags); scsi_run_queue(q); @@ -595,13 +623,14 @@ void scsi_run_host_queues(struct Scsi_Host *shost) * * Lock status: Assumed that lock is not held upon entry. * - * Returns: cmd if requeue done or required, NULL otherwise + * Returns: cmd if requeue required, NULL otherwise. * * Notes: This is called for block device requests in order to * mark some number of sectors as complete. * * We are guaranteeing that the request queue will be goosed * at some point during this call. + * Notes: If cmd was requeued, upon return it will be a stale pointer. */ static struct scsi_cmnd *scsi_end_request(struct scsi_cmnd *cmd, int uptodate, int bytes, int requeue) @@ -624,14 +653,15 @@ static struct scsi_cmnd *scsi_end_request(struct scsi_cmnd *cmd, int uptodate, if (!uptodate && blk_noretry_request(req)) end_that_request_chunk(req, 0, leftover); else { - if (requeue) + if (requeue) { /* * Bleah. Leftovers again. Stick the * leftovers in the front of the * queue, and goose the queue again. */ scsi_requeue_command(q, cmd); - + cmd = NULL; + } return cmd; } } @@ -857,15 +887,13 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes, * requeueing right here - we will requeue down below * when we handle the bad sectors. */ - cmd = scsi_end_request(cmd, 1, good_bytes, result == 0); /* - * If the command completed without error, then either finish off the - * rest of the command, or start a new one. + * If the command completed without error, then either + * finish off the rest of the command, or start a new one. */ - if (result == 0 || cmd == NULL ) { + if (scsi_end_request(cmd, 1, good_bytes, result == 0) == NULL) return; - } } /* * Now, if we were good little boys and girls, Santa left us a request @@ -880,7 +908,7 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes, * and quietly refuse further access. */ cmd->device->changed = 1; - cmd = scsi_end_request(cmd, 0, + scsi_end_request(cmd, 0, this_count, 1); return; } else { @@ -914,7 +942,7 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes, scsi_requeue_command(q, cmd); result = 0; } else { - cmd = scsi_end_request(cmd, 0, this_count, 1); + scsi_end_request(cmd, 0, this_count, 1); return; } break; @@ -931,7 +959,7 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes, dev_printk(KERN_INFO, &cmd->device->sdev_gendev, "Device not ready.\n"); - cmd = scsi_end_request(cmd, 0, this_count, 1); + scsi_end_request(cmd, 0, this_count, 1); return; case VOLUME_OVERFLOW: if (!(req->flags & REQ_QUIET)) { @@ -941,7 +969,7 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes, __scsi_print_command(cmd->data_cmnd); scsi_print_sense("", cmd); } - cmd = scsi_end_request(cmd, 0, block_bytes, 1); + scsi_end_request(cmd, 0, block_bytes, 1); return; default: break; @@ -972,7 +1000,7 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes, block_bytes = req->hard_cur_sectors << 9; if (!block_bytes) block_bytes = req->data_len; - cmd = scsi_end_request(cmd, 0, block_bytes, 1); + scsi_end_request(cmd, 0, block_bytes, 1); } } EXPORT_SYMBOL(scsi_io_completion); @@ -1118,7 +1146,7 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req) if (unlikely(!scsi_device_online(sdev))) { printk(KERN_ERR "scsi%d (%d:%d): rejecting I/O to offline device\n", sdev->host->host_no, sdev->id, sdev->lun); - return BLKPREP_KILL; + goto kill; } if (unlikely(sdev->sdev_state != SDEV_RUNNING)) { /* OK, we're not in a running state don't prep @@ -1128,7 +1156,7 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req) * at all allowed down */ printk(KERN_ERR "scsi%d (%d:%d): rejecting I/O to dead device\n", sdev->host->host_no, sdev->id, sdev->lun); - return BLKPREP_KILL; + goto kill; } /* OK, we only allow special commands (i.e. not * user initiated ones */ @@ -1160,11 +1188,11 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req) if(unlikely(specials_only) && !(req->flags & REQ_SPECIAL)) { if(specials_only == SDEV_QUIESCE || specials_only == SDEV_BLOCK) - return BLKPREP_DEFER; + goto defer; printk(KERN_ERR "scsi%d (%d:%d): rejecting I/O to device being removed\n", sdev->host->host_no, sdev->id, sdev->lun); - return BLKPREP_KILL; + goto kill; } @@ -1182,7 +1210,7 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req) cmd->tag = req->tag; } else { blk_dump_rq_flags(req, "SCSI bad req"); - return BLKPREP_KILL; + goto kill; } /* note the overloading of req->special. When the tag @@ -1220,8 +1248,13 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req) * required). */ ret = scsi_init_io(cmd); - if (ret) /* BLKPREP_KILL return also releases the command */ - return ret; + switch(ret) { + case BLKPREP_KILL: + /* BLKPREP_KILL return also releases the command */ + goto kill; + case BLKPREP_DEFER: + goto defer; + } /* * Initialize the actual SCSI command for this request. @@ -1231,7 +1264,7 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req) if (unlikely(!drv->init_command(cmd))) { scsi_release_buffers(cmd); scsi_put_command(cmd); - return BLKPREP_KILL; + goto kill; } } else { memcpy(cmd->cmnd, req->cmd, sizeof(cmd->cmnd)); @@ -1262,6 +1295,9 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req) if (sdev->device_busy == 0) blk_plug_device(q); return BLKPREP_DEFER; + kill: + req->errors = DID_NO_CONNECT << 16; + return BLKPREP_KILL; } /* @@ -1336,19 +1372,24 @@ static inline int scsi_host_queue_ready(struct request_queue *q, } /* - * Kill requests for a dead device + * Kill a request for a dead device */ -static void scsi_kill_requests(request_queue_t *q) +static void scsi_kill_request(struct request *req, request_queue_t *q) { - struct request *req; + struct scsi_cmnd *cmd = req->special; + + blkdev_dequeue_request(req); - while ((req = elv_next_request(q)) != NULL) { - blkdev_dequeue_request(req); - req->flags |= REQ_QUIET; - while (end_that_request_first(req, 0, req->nr_sectors)) - ; - end_that_request_last(req); + if (unlikely(cmd == NULL)) { + printk(KERN_CRIT "impossible request in %s.\n", + __FUNCTION__); + BUG(); } + + scsi_init_cmd_errh(cmd); + cmd->result = DID_NO_CONNECT << 16; + atomic_inc(&cmd->device->iorequest_cnt); + __scsi_done(cmd); } /* @@ -1371,7 +1412,8 @@ static void scsi_request_fn(struct request_queue *q) if (!sdev) { printk("scsi: killing requests for dead queue\n"); - scsi_kill_requests(q); + while ((req = elv_next_request(q)) != NULL) + scsi_kill_request(req, q); return; } @@ -1398,11 +1440,7 @@ static void scsi_request_fn(struct request_queue *q) if (unlikely(!scsi_device_online(sdev))) { printk(KERN_ERR "scsi%d (%d:%d): rejecting I/O to offline device\n", sdev->host->host_no, sdev->id, sdev->lun); - blkdev_dequeue_request(req); - req->flags |= REQ_QUIET; - while (end_that_request_first(req, 0, req->nr_sectors)) - ; - end_that_request_last(req); + scsi_kill_request(req, q); continue; } @@ -1415,6 +1453,14 @@ static void scsi_request_fn(struct request_queue *q) sdev->device_busy++; spin_unlock(q->queue_lock); + cmd = req->special; + if (unlikely(cmd == NULL)) { + printk(KERN_CRIT "impossible request in %s.\n" + "please mail a stack trace to " + "linux-scsi@vger.kernel.org", + __FUNCTION__); + BUG(); + } spin_lock(shost->host_lock); if (!scsi_host_queue_ready(q, shost, sdev)) @@ -1433,15 +1479,6 @@ static void scsi_request_fn(struct request_queue *q) */ spin_unlock_irq(shost->host_lock); - cmd = req->special; - if (unlikely(cmd == NULL)) { - printk(KERN_CRIT "impossible request in %s.\n" - "please mail a stack trace to " - "linux-scsi@vger.kernel.org", - __FUNCTION__); - BUG(); - } - /* * Finally, initialize any error handling parameters, and set up * the timers for timeouts. @@ -1477,6 +1514,7 @@ static void scsi_request_fn(struct request_queue *q) * cases (host limits or settings) should run the queue at some * later time. */ + scsi_unprep_request(req); spin_lock_irq(q->queue_lock); blk_requeue_request(q, req); sdev->device_busy--; diff --git a/drivers/scsi/scsi_priv.h b/drivers/scsi/scsi_priv.h index ee6de1768e53..d05f778d31a8 100644 --- a/drivers/scsi/scsi_priv.h +++ b/drivers/scsi/scsi_priv.h @@ -124,6 +124,7 @@ extern void scsi_sysfs_unregister(void); extern void scsi_sysfs_device_initialize(struct scsi_device *); extern int scsi_sysfs_target_initialize(struct scsi_device *); extern struct scsi_transport_template blank_transport_template; +extern void __scsi_remove_device(struct scsi_device *); extern struct bus_type scsi_bus_type; diff --git a/drivers/scsi/scsi_scan.c b/drivers/scsi/scsi_scan.c index 19c9a232a754..b86f170fa8ed 100644 --- a/drivers/scsi/scsi_scan.c +++ b/drivers/scsi/scsi_scan.c @@ -870,8 +870,12 @@ static int scsi_probe_and_add_lun(struct scsi_target *starget, out_free_sdev: if (res == SCSI_SCAN_LUN_PRESENT) { if (sdevp) { - scsi_device_get(sdev); - *sdevp = sdev; + if (scsi_device_get(sdev) == 0) { + *sdevp = sdev; + } else { + __scsi_remove_device(sdev); + res = SCSI_SCAN_NO_RESPONSE; + } } } else { if (sdev->host->hostt->slave_destroy) @@ -1260,6 +1264,19 @@ struct scsi_device *__scsi_add_device(struct Scsi_Host *shost, uint channel, } EXPORT_SYMBOL(__scsi_add_device); +int scsi_add_device(struct Scsi_Host *host, uint channel, + uint target, uint lun) +{ + struct scsi_device *sdev = + __scsi_add_device(host, channel, target, lun, NULL); + if (IS_ERR(sdev)) + return PTR_ERR(sdev); + + scsi_device_put(sdev); + return 0; +} +EXPORT_SYMBOL(scsi_add_device); + void scsi_rescan_device(struct device *dev) { struct scsi_driver *drv; @@ -1276,27 +1293,8 @@ void scsi_rescan_device(struct device *dev) } EXPORT_SYMBOL(scsi_rescan_device); -/** - * scsi_scan_target - scan a target id, possibly including all LUNs on the - * target. - * @sdevsca: Scsi_Device handle for scanning - * @shost: host to scan - * @channel: channel to scan - * @id: target id to scan - * - * Description: - * Scan the target id on @shost, @channel, and @id. Scan at least LUN - * 0, and possibly all LUNs on the target id. - * - * Use the pre-allocated @sdevscan as a handle for the scanning. This - * function sets sdevscan->host, sdevscan->id and sdevscan->lun; the - * scanning functions modify sdevscan->lun. - * - * First try a REPORT LUN scan, if that does not scan the target, do a - * sequential scan of LUNs on the target id. - **/ -void scsi_scan_target(struct device *parent, unsigned int channel, - unsigned int id, unsigned int lun, int rescan) +static void __scsi_scan_target(struct device *parent, unsigned int channel, + unsigned int id, unsigned int lun, int rescan) { struct Scsi_Host *shost = dev_to_shost(parent); int bflags = 0; @@ -1310,9 +1308,7 @@ void scsi_scan_target(struct device *parent, unsigned int channel, */ return; - starget = scsi_alloc_target(parent, channel, id); - if (!starget) return; @@ -1358,6 +1354,33 @@ void scsi_scan_target(struct device *parent, unsigned int channel, put_device(&starget->dev); } + +/** + * scsi_scan_target - scan a target id, possibly including all LUNs on the + * target. + * @parent: host to scan + * @channel: channel to scan + * @id: target id to scan + * @lun: Specific LUN to scan or SCAN_WILD_CARD + * @rescan: passed to LUN scanning routines + * + * Description: + * Scan the target id on @parent, @channel, and @id. Scan at least LUN 0, + * and possibly all LUNs on the target id. + * + * First try a REPORT LUN scan, if that does not scan the target, do a + * sequential scan of LUNs on the target id. + **/ +void scsi_scan_target(struct device *parent, unsigned int channel, + unsigned int id, unsigned int lun, int rescan) +{ + struct Scsi_Host *shost = dev_to_shost(parent); + + down(&shost->scan_mutex); + if (scsi_host_scan_allowed(shost)) + __scsi_scan_target(parent, channel, id, lun, rescan); + up(&shost->scan_mutex); +} EXPORT_SYMBOL(scsi_scan_target); static void scsi_scan_channel(struct Scsi_Host *shost, unsigned int channel, @@ -1383,10 +1406,12 @@ static void scsi_scan_channel(struct Scsi_Host *shost, unsigned int channel, order_id = shost->max_id - id - 1; else order_id = id; - scsi_scan_target(&shost->shost_gendev, channel, order_id, lun, rescan); + __scsi_scan_target(&shost->shost_gendev, channel, + order_id, lun, rescan); } else - scsi_scan_target(&shost->shost_gendev, channel, id, lun, rescan); + __scsi_scan_target(&shost->shost_gendev, channel, + id, lun, rescan); } int scsi_scan_host_selected(struct Scsi_Host *shost, unsigned int channel, @@ -1484,12 +1509,15 @@ void scsi_forget_host(struct Scsi_Host *shost) */ struct scsi_device *scsi_get_host_dev(struct Scsi_Host *shost) { - struct scsi_device *sdev; + struct scsi_device *sdev = NULL; struct scsi_target *starget; + down(&shost->scan_mutex); + if (!scsi_host_scan_allowed(shost)) + goto out; starget = scsi_alloc_target(&shost->shost_gendev, 0, shost->this_id); if (!starget) - return NULL; + goto out; sdev = scsi_alloc_sdev(starget, 0, NULL); if (sdev) { @@ -1497,6 +1525,8 @@ struct scsi_device *scsi_get_host_dev(struct Scsi_Host *shost) sdev->borken = 0; } put_device(&starget->dev); + out: + up(&shost->scan_mutex); return sdev; } EXPORT_SYMBOL(scsi_get_host_dev); diff --git a/drivers/scsi/scsi_sysfs.c b/drivers/scsi/scsi_sysfs.c index dae59d1da07a..b8052d5206cc 100644 --- a/drivers/scsi/scsi_sysfs.c +++ b/drivers/scsi/scsi_sysfs.c @@ -653,7 +653,7 @@ int scsi_sysfs_add_sdev(struct scsi_device *sdev) error = attr_add(&sdev->sdev_gendev, sdev->host->hostt->sdev_attrs[i]); if (error) { - scsi_remove_device(sdev); + __scsi_remove_device(sdev); goto out; } } @@ -667,7 +667,7 @@ int scsi_sysfs_add_sdev(struct scsi_device *sdev) scsi_sysfs_sdev_attrs[i]); error = device_create_file(&sdev->sdev_gendev, attr); if (error) { - scsi_remove_device(sdev); + __scsi_remove_device(sdev); goto out; } } @@ -687,17 +687,10 @@ int scsi_sysfs_add_sdev(struct scsi_device *sdev) return error; } -/** - * scsi_remove_device - unregister a device from the scsi bus - * @sdev: scsi_device to unregister - **/ -void scsi_remove_device(struct scsi_device *sdev) +void __scsi_remove_device(struct scsi_device *sdev) { - struct Scsi_Host *shost = sdev->host; - - down(&shost->scan_mutex); if (scsi_device_set_state(sdev, SDEV_CANCEL) != 0) - goto out; + return; class_device_unregister(&sdev->sdev_classdev); device_del(&sdev->sdev_gendev); @@ -706,8 +699,17 @@ void scsi_remove_device(struct scsi_device *sdev) sdev->host->hostt->slave_destroy(sdev); transport_unregister_device(&sdev->sdev_gendev); put_device(&sdev->sdev_gendev); -out: - up(&shost->scan_mutex); +} + +/** + * scsi_remove_device - unregister a device from the scsi bus + * @sdev: scsi_device to unregister + **/ +void scsi_remove_device(struct scsi_device *sdev) +{ + down(&sdev->host->scan_mutex); + __scsi_remove_device(sdev); + up(&sdev->host->scan_mutex); } EXPORT_SYMBOL(scsi_remove_device); diff --git a/drivers/scsi/scsi_transport_sas.c b/drivers/scsi/scsi_transport_sas.c new file mode 100644 index 000000000000..ff724bbe6611 --- /dev/null +++ b/drivers/scsi/scsi_transport_sas.c @@ -0,0 +1,820 @@ +/* + * Copyright (C) 2005 Dell Inc. + * Released under GPL v2. + * + * Serial Attached SCSI (SAS) transport class. + * + * The SAS transport class contains common code to deal with SAS HBAs, + * an aproximated representation of SAS topologies in the driver model, + * and various sysfs attributes to expose these topologies and managment + * interfaces to userspace. + * + * In addition to the basic SCSI core objects this transport class + * introduces two additional intermediate objects: The SAS PHY + * as represented by struct sas_phy defines an "outgoing" PHY on + * a SAS HBA or Expander, and the SAS remote PHY represented by + * struct sas_rphy defines an "incoming" PHY on a SAS Expander or + * end device. Note that this is purely a software concept, the + * underlying hardware for a PHY and a remote PHY is the exactly + * the same. + * + * There is no concept of a SAS port in this code, users can see + * what PHYs form a wide port based on the port_identifier attribute, + * which is the same for all PHYs in a port. + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/err.h> + +#include <scsi/scsi_device.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_transport.h> +#include <scsi/scsi_transport_sas.h> + + +#define SAS_HOST_ATTRS 0 +#define SAS_PORT_ATTRS 11 +#define SAS_RPORT_ATTRS 5 + +struct sas_internal { + struct scsi_transport_template t; + struct sas_function_template *f; + + struct class_device_attribute private_host_attrs[SAS_HOST_ATTRS]; + struct class_device_attribute private_phy_attrs[SAS_PORT_ATTRS]; + struct class_device_attribute private_rphy_attrs[SAS_RPORT_ATTRS]; + + struct transport_container phy_attr_cont; + struct transport_container rphy_attr_cont; + + /* + * The array of null terminated pointers to attributes + * needed by scsi_sysfs.c + */ + struct class_device_attribute *host_attrs[SAS_HOST_ATTRS + 1]; + struct class_device_attribute *phy_attrs[SAS_PORT_ATTRS + 1]; + struct class_device_attribute *rphy_attrs[SAS_RPORT_ATTRS + 1]; +}; +#define to_sas_internal(tmpl) container_of(tmpl, struct sas_internal, t) + +struct sas_host_attrs { + struct list_head rphy_list; + spinlock_t lock; + u32 next_target_id; +}; +#define to_sas_host_attrs(host) ((struct sas_host_attrs *)(host)->shost_data) + + +/* + * Hack to allow attributes of the same name in different objects. + */ +#define SAS_CLASS_DEVICE_ATTR(_prefix,_name,_mode,_show,_store) \ + struct class_device_attribute class_device_attr_##_prefix##_##_name = \ + __ATTR(_name,_mode,_show,_store) + + +/* + * Pretty printing helpers + */ + +#define sas_bitfield_name_match(title, table) \ +static ssize_t \ +get_sas_##title##_names(u32 table_key, char *buf) \ +{ \ + char *prefix = ""; \ + ssize_t len = 0; \ + int i; \ + \ + for (i = 0; i < sizeof(table)/sizeof(table[0]); i++) { \ + if (table[i].value & table_key) { \ + len += sprintf(buf + len, "%s%s", \ + prefix, table[i].name); \ + prefix = ", "; \ + } \ + } \ + len += sprintf(buf + len, "\n"); \ + return len; \ +} + +#define sas_bitfield_name_search(title, table) \ +static ssize_t \ +get_sas_##title##_names(u32 table_key, char *buf) \ +{ \ + ssize_t len = 0; \ + int i; \ + \ + for (i = 0; i < sizeof(table)/sizeof(table[0]); i++) { \ + if (table[i].value == table_key) { \ + len += sprintf(buf + len, "%s", \ + table[i].name); \ + break; \ + } \ + } \ + len += sprintf(buf + len, "\n"); \ + return len; \ +} + +static struct { + u32 value; + char *name; +} sas_device_type_names[] = { + { SAS_PHY_UNUSED, "unused" }, + { SAS_END_DEVICE, "end device" }, + { SAS_EDGE_EXPANDER_DEVICE, "edge expander" }, + { SAS_FANOUT_EXPANDER_DEVICE, "fanout expander" }, +}; +sas_bitfield_name_search(device_type, sas_device_type_names) + + +static struct { + u32 value; + char *name; +} sas_protocol_names[] = { + { SAS_PROTOCOL_SATA, "sata" }, + { SAS_PROTOCOL_SMP, "smp" }, + { SAS_PROTOCOL_STP, "stp" }, + { SAS_PROTOCOL_SSP, "ssp" }, +}; +sas_bitfield_name_match(protocol, sas_protocol_names) + +static struct { + u32 value; + char *name; +} sas_linkspeed_names[] = { + { SAS_LINK_RATE_UNKNOWN, "Unknown" }, + { SAS_PHY_DISABLED, "Phy disabled" }, + { SAS_LINK_RATE_FAILED, "Link Rate failed" }, + { SAS_SATA_SPINUP_HOLD, "Spin-up hold" }, + { SAS_LINK_RATE_1_5_GBPS, "1.5 Gbit" }, + { SAS_LINK_RATE_3_0_GBPS, "3.0 Gbit" }, +}; +sas_bitfield_name_search(linkspeed, sas_linkspeed_names) + + +/* + * SAS host attributes + */ + +static int sas_host_setup(struct transport_container *tc, struct device *dev, + struct class_device *cdev) +{ + struct Scsi_Host *shost = dev_to_shost(dev); + struct sas_host_attrs *sas_host = to_sas_host_attrs(shost); + + INIT_LIST_HEAD(&sas_host->rphy_list); + spin_lock_init(&sas_host->lock); + sas_host->next_target_id = 0; + return 0; +} + +static DECLARE_TRANSPORT_CLASS(sas_host_class, + "sas_host", sas_host_setup, NULL, NULL); + +static int sas_host_match(struct attribute_container *cont, + struct device *dev) +{ + struct Scsi_Host *shost; + struct sas_internal *i; + + if (!scsi_is_host_device(dev)) + return 0; + shost = dev_to_shost(dev); + + if (!shost->transportt) + return 0; + if (shost->transportt->host_attrs.ac.class != + &sas_host_class.class) + return 0; + + i = to_sas_internal(shost->transportt); + return &i->t.host_attrs.ac == cont; +} + +static int do_sas_phy_delete(struct device *dev, void *data) +{ + if (scsi_is_sas_phy(dev)) + sas_phy_delete(dev_to_phy(dev)); + return 0; +} + +/** + * sas_remove_host -- tear down a Scsi_Host's SAS data structures + * @shost: Scsi Host that is torn down + * + * Removes all SAS PHYs and remote PHYs for a given Scsi_Host. + * Must be called just before scsi_remove_host for SAS HBAs. + */ +void sas_remove_host(struct Scsi_Host *shost) +{ + device_for_each_child(&shost->shost_gendev, NULL, do_sas_phy_delete); +} +EXPORT_SYMBOL(sas_remove_host); + + +/* + * SAS Port attributes + */ + +#define sas_phy_show_simple(field, name, format_string, cast) \ +static ssize_t \ +show_sas_phy_##name(struct class_device *cdev, char *buf) \ +{ \ + struct sas_phy *phy = transport_class_to_phy(cdev); \ + \ + return snprintf(buf, 20, format_string, cast phy->field); \ +} + +#define sas_phy_simple_attr(field, name, format_string, type) \ + sas_phy_show_simple(field, name, format_string, (type)) \ +static CLASS_DEVICE_ATTR(name, S_IRUGO, show_sas_phy_##name, NULL) + +#define sas_phy_show_protocol(field, name) \ +static ssize_t \ +show_sas_phy_##name(struct class_device *cdev, char *buf) \ +{ \ + struct sas_phy *phy = transport_class_to_phy(cdev); \ + \ + if (!phy->field) \ + return snprintf(buf, 20, "none\n"); \ + return get_sas_protocol_names(phy->field, buf); \ +} + +#define sas_phy_protocol_attr(field, name) \ + sas_phy_show_protocol(field, name) \ +static CLASS_DEVICE_ATTR(name, S_IRUGO, show_sas_phy_##name, NULL) + +#define sas_phy_show_linkspeed(field) \ +static ssize_t \ +show_sas_phy_##field(struct class_device *cdev, char *buf) \ +{ \ + struct sas_phy *phy = transport_class_to_phy(cdev); \ + \ + return get_sas_linkspeed_names(phy->field, buf); \ +} + +#define sas_phy_linkspeed_attr(field) \ + sas_phy_show_linkspeed(field) \ +static CLASS_DEVICE_ATTR(field, S_IRUGO, show_sas_phy_##field, NULL) + +static ssize_t +show_sas_device_type(struct class_device *cdev, char *buf) +{ + struct sas_phy *phy = transport_class_to_phy(cdev); + + if (!phy->identify.device_type) + return snprintf(buf, 20, "none\n"); + return get_sas_device_type_names(phy->identify.device_type, buf); +} + +static CLASS_DEVICE_ATTR(device_type, S_IRUGO, show_sas_device_type, NULL); + +sas_phy_protocol_attr(identify.initiator_port_protocols, + initiator_port_protocols); +sas_phy_protocol_attr(identify.target_port_protocols, + target_port_protocols); +sas_phy_simple_attr(identify.sas_address, sas_address, "0x%016llx\n", + unsigned long long); +sas_phy_simple_attr(identify.phy_identifier, phy_identifier, "%d\n", u8); +sas_phy_simple_attr(port_identifier, port_identifier, "%d\n", u8); +sas_phy_linkspeed_attr(negotiated_linkrate); +sas_phy_linkspeed_attr(minimum_linkrate_hw); +sas_phy_linkspeed_attr(minimum_linkrate); +sas_phy_linkspeed_attr(maximum_linkrate_hw); +sas_phy_linkspeed_attr(maximum_linkrate); + + +static DECLARE_TRANSPORT_CLASS(sas_phy_class, + "sas_phy", NULL, NULL, NULL); + +static int sas_phy_match(struct attribute_container *cont, struct device *dev) +{ + struct Scsi_Host *shost; + struct sas_internal *i; + + if (!scsi_is_sas_phy(dev)) + return 0; + shost = dev_to_shost(dev->parent); + + if (!shost->transportt) + return 0; + if (shost->transportt->host_attrs.ac.class != + &sas_host_class.class) + return 0; + + i = to_sas_internal(shost->transportt); + return &i->phy_attr_cont.ac == cont; +} + +static void sas_phy_release(struct device *dev) +{ + struct sas_phy *phy = dev_to_phy(dev); + + put_device(dev->parent); + kfree(phy); +} + +/** + * sas_phy_alloc -- allocates and initialize a SAS PHY structure + * @parent: Parent device + * @number: Port number + * + * Allocates an SAS PHY structure. It will be added in the device tree + * below the device specified by @parent, which has to be either a Scsi_Host + * or sas_rphy. + * + * Returns: + * SAS PHY allocated or %NULL if the allocation failed. + */ +struct sas_phy *sas_phy_alloc(struct device *parent, int number) +{ + struct Scsi_Host *shost = dev_to_shost(parent); + struct sas_phy *phy; + + phy = kmalloc(sizeof(*phy), GFP_KERNEL); + if (!phy) + return NULL; + memset(phy, 0, sizeof(*phy)); + + get_device(parent); + + phy->number = number; + + device_initialize(&phy->dev); + phy->dev.parent = get_device(parent); + phy->dev.release = sas_phy_release; + sprintf(phy->dev.bus_id, "phy-%d:%d", shost->host_no, number); + + transport_setup_device(&phy->dev); + + return phy; +} +EXPORT_SYMBOL(sas_phy_alloc); + +/** + * sas_phy_add -- add a SAS PHY to the device hierachy + * @phy: The PHY to be added + * + * Publishes a SAS PHY to the rest of the system. + */ +int sas_phy_add(struct sas_phy *phy) +{ + int error; + + error = device_add(&phy->dev); + if (!error) { + transport_add_device(&phy->dev); + transport_configure_device(&phy->dev); + } + + return error; +} +EXPORT_SYMBOL(sas_phy_add); + +/** + * sas_phy_free -- free a SAS PHY + * @phy: SAS PHY to free + * + * Frees the specified SAS PHY. + * + * Note: + * This function must only be called on a PHY that has not + * sucessfully been added using sas_phy_add(). + */ +void sas_phy_free(struct sas_phy *phy) +{ + transport_destroy_device(&phy->dev); + put_device(phy->dev.parent); + put_device(phy->dev.parent); + put_device(phy->dev.parent); + kfree(phy); +} +EXPORT_SYMBOL(sas_phy_free); + +/** + * sas_phy_delete -- remove SAS PHY + * @phy: SAS PHY to remove + * + * Removes the specified SAS PHY. If the SAS PHY has an + * associated remote PHY it is removed before. + */ +void +sas_phy_delete(struct sas_phy *phy) +{ + struct device *dev = &phy->dev; + + if (phy->rphy) + sas_rphy_delete(phy->rphy); + + transport_remove_device(dev); + device_del(dev); + transport_destroy_device(dev); + put_device(dev->parent); +} +EXPORT_SYMBOL(sas_phy_delete); + +/** + * scsi_is_sas_phy -- check if a struct device represents a SAS PHY + * @dev: device to check + * + * Returns: + * %1 if the device represents a SAS PHY, %0 else + */ +int scsi_is_sas_phy(const struct device *dev) +{ + return dev->release == sas_phy_release; +} +EXPORT_SYMBOL(scsi_is_sas_phy); + +/* + * SAS remote PHY attributes. + */ + +#define sas_rphy_show_simple(field, name, format_string, cast) \ +static ssize_t \ +show_sas_rphy_##name(struct class_device *cdev, char *buf) \ +{ \ + struct sas_rphy *rphy = transport_class_to_rphy(cdev); \ + \ + return snprintf(buf, 20, format_string, cast rphy->field); \ +} + +#define sas_rphy_simple_attr(field, name, format_string, type) \ + sas_rphy_show_simple(field, name, format_string, (type)) \ +static SAS_CLASS_DEVICE_ATTR(rphy, name, S_IRUGO, \ + show_sas_rphy_##name, NULL) + +#define sas_rphy_show_protocol(field, name) \ +static ssize_t \ +show_sas_rphy_##name(struct class_device *cdev, char *buf) \ +{ \ + struct sas_rphy *rphy = transport_class_to_rphy(cdev); \ + \ + if (!rphy->field) \ + return snprintf(buf, 20, "none\n"); \ + return get_sas_protocol_names(rphy->field, buf); \ +} + +#define sas_rphy_protocol_attr(field, name) \ + sas_rphy_show_protocol(field, name) \ +static SAS_CLASS_DEVICE_ATTR(rphy, name, S_IRUGO, \ + show_sas_rphy_##name, NULL) + +static ssize_t +show_sas_rphy_device_type(struct class_device *cdev, char *buf) +{ + struct sas_rphy *rphy = transport_class_to_rphy(cdev); + + if (!rphy->identify.device_type) + return snprintf(buf, 20, "none\n"); + return get_sas_device_type_names( + rphy->identify.device_type, buf); +} + +static SAS_CLASS_DEVICE_ATTR(rphy, device_type, S_IRUGO, + show_sas_rphy_device_type, NULL); + +sas_rphy_protocol_attr(identify.initiator_port_protocols, + initiator_port_protocols); +sas_rphy_protocol_attr(identify.target_port_protocols, target_port_protocols); +sas_rphy_simple_attr(identify.sas_address, sas_address, "0x%016llx\n", + unsigned long long); +sas_rphy_simple_attr(identify.phy_identifier, phy_identifier, "%d\n", u8); + +static DECLARE_TRANSPORT_CLASS(sas_rphy_class, + "sas_rphy", NULL, NULL, NULL); + +static int sas_rphy_match(struct attribute_container *cont, struct device *dev) +{ + struct Scsi_Host *shost; + struct sas_internal *i; + + if (!scsi_is_sas_rphy(dev)) + return 0; + shost = dev_to_shost(dev->parent->parent); + + if (!shost->transportt) + return 0; + if (shost->transportt->host_attrs.ac.class != + &sas_host_class.class) + return 0; + + i = to_sas_internal(shost->transportt); + return &i->rphy_attr_cont.ac == cont; +} + +static void sas_rphy_release(struct device *dev) +{ + struct sas_rphy *rphy = dev_to_rphy(dev); + + put_device(dev->parent); + kfree(rphy); +} + +/** + * sas_rphy_alloc -- allocates and initialize a SAS remote PHY structure + * @parent: SAS PHY this remote PHY is conneted to + * + * Allocates an SAS remote PHY structure, connected to @parent. + * + * Returns: + * SAS PHY allocated or %NULL if the allocation failed. + */ +struct sas_rphy *sas_rphy_alloc(struct sas_phy *parent) +{ + struct Scsi_Host *shost = dev_to_shost(&parent->dev); + struct sas_rphy *rphy; + + rphy = kmalloc(sizeof(*rphy), GFP_KERNEL); + if (!rphy) { + put_device(&parent->dev); + return NULL; + } + memset(rphy, 0, sizeof(*rphy)); + + device_initialize(&rphy->dev); + rphy->dev.parent = get_device(&parent->dev); + rphy->dev.release = sas_rphy_release; + sprintf(rphy->dev.bus_id, "rphy-%d:%d", + shost->host_no, parent->number); + transport_setup_device(&rphy->dev); + + return rphy; +} +EXPORT_SYMBOL(sas_rphy_alloc); + +/** + * sas_rphy_add -- add a SAS remote PHY to the device hierachy + * @rphy: The remote PHY to be added + * + * Publishes a SAS remote PHY to the rest of the system. + */ +int sas_rphy_add(struct sas_rphy *rphy) +{ + struct sas_phy *parent = dev_to_phy(rphy->dev.parent); + struct Scsi_Host *shost = dev_to_shost(parent->dev.parent); + struct sas_host_attrs *sas_host = to_sas_host_attrs(shost); + struct sas_identify *identify = &rphy->identify; + int error; + + if (parent->rphy) + return -ENXIO; + parent->rphy = rphy; + + error = device_add(&rphy->dev); + if (error) + return error; + transport_add_device(&rphy->dev); + transport_configure_device(&rphy->dev); + + spin_lock(&sas_host->lock); + list_add_tail(&rphy->list, &sas_host->rphy_list); + if (identify->device_type == SAS_END_DEVICE && + (identify->target_port_protocols & + (SAS_PROTOCOL_SSP|SAS_PROTOCOL_STP|SAS_PROTOCOL_SATA))) + rphy->scsi_target_id = sas_host->next_target_id++; + else + rphy->scsi_target_id = -1; + spin_unlock(&sas_host->lock); + + if (rphy->scsi_target_id != -1) { + scsi_scan_target(&rphy->dev, parent->number, + rphy->scsi_target_id, ~0, 0); + } + + return 0; +} +EXPORT_SYMBOL(sas_rphy_add); + +/** + * sas_rphy_free -- free a SAS remote PHY + * @rphy SAS remote PHY to free + * + * Frees the specified SAS remote PHY. + * + * Note: + * This function must only be called on a remote + * PHY that has not sucessfully been added using + * sas_rphy_add(). + */ +void sas_rphy_free(struct sas_rphy *rphy) +{ + struct Scsi_Host *shost = dev_to_shost(rphy->dev.parent->parent); + struct sas_host_attrs *sas_host = to_sas_host_attrs(shost); + + spin_lock(&sas_host->lock); + list_del(&rphy->list); + spin_unlock(&sas_host->lock); + + transport_destroy_device(&rphy->dev); + put_device(rphy->dev.parent); + put_device(rphy->dev.parent); + put_device(rphy->dev.parent); + kfree(rphy); +} +EXPORT_SYMBOL(sas_rphy_free); + +/** + * sas_rphy_delete -- remove SAS remote PHY + * @rphy: SAS remote PHY to remove + * + * Removes the specified SAS remote PHY. + */ +void +sas_rphy_delete(struct sas_rphy *rphy) +{ + struct device *dev = &rphy->dev; + struct sas_phy *parent = dev_to_phy(dev->parent); + struct Scsi_Host *shost = dev_to_shost(parent->dev.parent); + struct sas_host_attrs *sas_host = to_sas_host_attrs(shost); + + transport_destroy_device(&rphy->dev); + + scsi_remove_target(&rphy->dev); + + spin_lock(&sas_host->lock); + list_del(&rphy->list); + spin_unlock(&sas_host->lock); + + transport_remove_device(dev); + device_del(dev); + transport_destroy_device(dev); + put_device(&parent->dev); +} +EXPORT_SYMBOL(sas_rphy_delete); + +/** + * scsi_is_sas_rphy -- check if a struct device represents a SAS remote PHY + * @dev: device to check + * + * Returns: + * %1 if the device represents a SAS remote PHY, %0 else + */ +int scsi_is_sas_rphy(const struct device *dev) +{ + return dev->release == sas_rphy_release; +} +EXPORT_SYMBOL(scsi_is_sas_rphy); + + +/* + * SCSI scan helper + */ + +static struct device *sas_target_parent(struct Scsi_Host *shost, + int channel, uint id) +{ + struct sas_host_attrs *sas_host = to_sas_host_attrs(shost); + struct sas_rphy *rphy; + struct device *dev = NULL; + + spin_lock(&sas_host->lock); + list_for_each_entry(rphy, &sas_host->rphy_list, list) { + struct sas_phy *parent = dev_to_phy(rphy->dev.parent); + if (parent->number == channel && + rphy->scsi_target_id == id) + dev = &rphy->dev; + } + spin_unlock(&sas_host->lock); + + return dev; +} + + +/* + * Setup / Teardown code + */ + +#define SETUP_RPORT_ATTRIBUTE(field) \ + i->private_rphy_attrs[count] = class_device_attr_##field; \ + i->private_rphy_attrs[count].attr.mode = S_IRUGO; \ + i->private_rphy_attrs[count].store = NULL; \ + i->rphy_attrs[count] = &i->private_rphy_attrs[count]; \ + count++ + +#define SETUP_PORT_ATTRIBUTE(field) \ + i->private_phy_attrs[count] = class_device_attr_##field; \ + i->private_phy_attrs[count].attr.mode = S_IRUGO; \ + i->private_phy_attrs[count].store = NULL; \ + i->phy_attrs[count] = &i->private_phy_attrs[count]; \ + count++ + + +/** + * sas_attach_transport -- instantiate SAS transport template + * @ft: SAS transport class function template + */ +struct scsi_transport_template * +sas_attach_transport(struct sas_function_template *ft) +{ + struct sas_internal *i; + int count; + + i = kmalloc(sizeof(struct sas_internal), GFP_KERNEL); + if (!i) + return NULL; + memset(i, 0, sizeof(struct sas_internal)); + + i->t.target_parent = sas_target_parent; + + i->t.host_attrs.ac.attrs = &i->host_attrs[0]; + i->t.host_attrs.ac.class = &sas_host_class.class; + i->t.host_attrs.ac.match = sas_host_match; + transport_container_register(&i->t.host_attrs); + i->t.host_size = sizeof(struct sas_host_attrs); + + i->phy_attr_cont.ac.class = &sas_phy_class.class; + i->phy_attr_cont.ac.attrs = &i->phy_attrs[0]; + i->phy_attr_cont.ac.match = sas_phy_match; + transport_container_register(&i->phy_attr_cont); + + i->rphy_attr_cont.ac.class = &sas_rphy_class.class; + i->rphy_attr_cont.ac.attrs = &i->rphy_attrs[0]; + i->rphy_attr_cont.ac.match = sas_rphy_match; + transport_container_register(&i->rphy_attr_cont); + + i->f = ft; + + count = 0; + i->host_attrs[count] = NULL; + + count = 0; + SETUP_PORT_ATTRIBUTE(initiator_port_protocols); + SETUP_PORT_ATTRIBUTE(target_port_protocols); + SETUP_PORT_ATTRIBUTE(device_type); + SETUP_PORT_ATTRIBUTE(sas_address); + SETUP_PORT_ATTRIBUTE(phy_identifier); + SETUP_PORT_ATTRIBUTE(port_identifier); + SETUP_PORT_ATTRIBUTE(negotiated_linkrate); + SETUP_PORT_ATTRIBUTE(minimum_linkrate_hw); + SETUP_PORT_ATTRIBUTE(minimum_linkrate); + SETUP_PORT_ATTRIBUTE(maximum_linkrate_hw); + SETUP_PORT_ATTRIBUTE(maximum_linkrate); + i->phy_attrs[count] = NULL; + + count = 0; + SETUP_RPORT_ATTRIBUTE(rphy_initiator_port_protocols); + SETUP_RPORT_ATTRIBUTE(rphy_target_port_protocols); + SETUP_RPORT_ATTRIBUTE(rphy_device_type); + SETUP_RPORT_ATTRIBUTE(rphy_sas_address); + SETUP_RPORT_ATTRIBUTE(rphy_phy_identifier); + i->rphy_attrs[count] = NULL; + + return &i->t; +} +EXPORT_SYMBOL(sas_attach_transport); + +/** + * sas_release_transport -- release SAS transport template instance + * @t: transport template instance + */ +void sas_release_transport(struct scsi_transport_template *t) +{ + struct sas_internal *i = to_sas_internal(t); + + transport_container_unregister(&i->t.host_attrs); + transport_container_unregister(&i->phy_attr_cont); + transport_container_unregister(&i->rphy_attr_cont); + + kfree(i); +} +EXPORT_SYMBOL(sas_release_transport); + +static __init int sas_transport_init(void) +{ + int error; + + error = transport_class_register(&sas_host_class); + if (error) + goto out; + error = transport_class_register(&sas_phy_class); + if (error) + goto out_unregister_transport; + error = transport_class_register(&sas_rphy_class); + if (error) + goto out_unregister_phy; + + return 0; + + out_unregister_phy: + transport_class_unregister(&sas_phy_class); + out_unregister_transport: + transport_class_unregister(&sas_host_class); + out: + return error; + +} + +static void __exit sas_transport_exit(void) +{ + transport_class_unregister(&sas_host_class); + transport_class_unregister(&sas_phy_class); + transport_class_unregister(&sas_rphy_class); +} + +MODULE_AUTHOR("Christoph Hellwig"); +MODULE_DESCRIPTION("SAS Transphy Attributes"); +MODULE_LICENSE("GPL"); + +module_init(sas_transport_init); +module_exit(sas_transport_exit); diff --git a/drivers/scsi/sg.c b/drivers/scsi/sg.c index b1b69d738d08..9ea4765d1d12 100644 --- a/drivers/scsi/sg.c +++ b/drivers/scsi/sg.c @@ -61,7 +61,7 @@ static int sg_version_num = 30533; /* 2 digits for each component */ #ifdef CONFIG_SCSI_PROC_FS #include <linux/proc_fs.h> -static char *sg_version_date = "20050901"; +static char *sg_version_date = "20050908"; static int sg_proc_init(void); static void sg_proc_cleanup(void); @@ -1299,7 +1299,7 @@ sg_mmap(struct file *filp, struct vm_area_struct *vma) sg_rb_correct4mmap(rsv_schp, 1); /* do only once per fd lifetime */ sfp->mmap_called = 1; } - vma->vm_flags |= (VM_RESERVED | VM_IO); + vma->vm_flags |= VM_RESERVED; vma->vm_private_data = sfp; vma->vm_ops = &sg_mmap_vm_ops; return 0; diff --git a/include/scsi/scsi_device.h b/include/scsi/scsi_device.h index da63722c0123..c0e4c67d836f 100644 --- a/include/scsi/scsi_device.h +++ b/include/scsi/scsi_device.h @@ -178,8 +178,8 @@ static inline struct scsi_target *scsi_target(struct scsi_device *sdev) extern struct scsi_device *__scsi_add_device(struct Scsi_Host *, uint, uint, uint, void *hostdata); -#define scsi_add_device(host, channel, target, lun) \ - __scsi_add_device(host, channel, target, lun, NULL) +extern int scsi_add_device(struct Scsi_Host *host, uint channel, + uint target, uint lun); extern void scsi_remove_device(struct scsi_device *); extern int scsi_device_cancel(struct scsi_device *, int); diff --git a/include/scsi/scsi_transport_fc.h b/include/scsi/scsi_transport_fc.h index 70ad16315a16..115db056dc6b 100644 --- a/include/scsi/scsi_transport_fc.h +++ b/include/scsi/scsi_transport_fc.h @@ -439,4 +439,12 @@ int fc_remote_port_block(struct fc_rport *rport); void fc_remote_port_unblock(struct fc_rport *rport); int scsi_is_fc_rport(const struct device *); +static inline u64 wwn_to_u64(u8 *wwn) +{ + return (u64)wwn[0] << 56 | (u64)wwn[1] << 48 | + (u64)wwn[2] << 40 | (u64)wwn[3] << 32 | + (u64)wwn[4] << 24 | (u64)wwn[5] << 16 | + (u64)wwn[6] << 8 | (u64)wwn[7]; +} + #endif /* SCSI_TRANSPORT_FC_H */ diff --git a/include/scsi/scsi_transport_sas.h b/include/scsi/scsi_transport_sas.h new file mode 100644 index 000000000000..bc4aeb660dd3 --- /dev/null +++ b/include/scsi/scsi_transport_sas.h @@ -0,0 +1,100 @@ +#ifndef SCSI_TRANSPORT_SAS_H +#define SCSI_TRANSPORT_SAS_H + +#include <linux/transport_class.h> +#include <linux/types.h> + +struct scsi_transport_template; +struct sas_rphy; + + +enum sas_device_type { + SAS_PHY_UNUSED, + SAS_END_DEVICE, + SAS_EDGE_EXPANDER_DEVICE, + SAS_FANOUT_EXPANDER_DEVICE, +}; + +enum sas_protocol { + SAS_PROTOCOL_SATA = 0x01, + SAS_PROTOCOL_SMP = 0x02, + SAS_PROTOCOL_STP = 0x04, + SAS_PROTOCOL_SSP = 0x08, +}; + +enum sas_linkrate { + SAS_LINK_RATE_UNKNOWN, + SAS_PHY_DISABLED, + SAS_LINK_RATE_FAILED, + SAS_SATA_SPINUP_HOLD, + SAS_SATA_PORT_SELECTOR, + SAS_LINK_RATE_1_5_GBPS, + SAS_LINK_RATE_3_0_GBPS, + SAS_LINK_VIRTUAL, +}; + +struct sas_identify { + enum sas_device_type device_type; + enum sas_protocol initiator_port_protocols; + enum sas_protocol target_port_protocols; + u64 sas_address; + u8 phy_identifier; +}; + +/* The functions by which the transport class and the driver communicate */ +struct sas_function_template { +}; + +struct sas_phy { + struct device dev; + int number; + struct sas_identify identify; + enum sas_linkrate negotiated_linkrate; + enum sas_linkrate minimum_linkrate_hw; + enum sas_linkrate minimum_linkrate; + enum sas_linkrate maximum_linkrate_hw; + enum sas_linkrate maximum_linkrate; + u8 port_identifier; + struct sas_rphy *rphy; +}; + +#define dev_to_phy(d) \ + container_of((d), struct sas_phy, dev) +#define transport_class_to_phy(cdev) \ + dev_to_phy((cdev)->dev) +#define phy_to_shost(phy) \ + dev_to_shost((phy)->dev.parent) + +struct sas_rphy { + struct device dev; + struct sas_identify identify; + struct list_head list; + u32 scsi_target_id; +}; + +#define dev_to_rphy(d) \ + container_of((d), struct sas_rphy, dev) +#define transport_class_to_rphy(cdev) \ + dev_to_rphy((cdev)->dev) +#define rphy_to_shost(rphy) \ + dev_to_shost((rphy)->dev.parent) + +extern void sas_remove_host(struct Scsi_Host *); + +extern struct sas_phy *sas_phy_alloc(struct device *, int); +extern void sas_phy_free(struct sas_phy *); +extern int sas_phy_add(struct sas_phy *); +extern void sas_phy_delete(struct sas_phy *); +extern int scsi_is_sas_phy(const struct device *); + +extern struct sas_rphy *sas_rphy_alloc(struct sas_phy *); +void sas_rphy_free(struct sas_rphy *); +extern int sas_rphy_add(struct sas_rphy *); +extern void sas_rphy_delete(struct sas_rphy *); +extern int scsi_is_sas_rphy(const struct device *); + +extern struct scsi_transport_template * +sas_attach_transport(struct sas_function_template *); +extern void sas_release_transport(struct scsi_transport_template *); + +#endif /* SCSI_TRANSPORT_SAS_H */ |