diff options
| -rw-r--r-- | Documentation/devicetree/bindings/pinctrl/fsl,imx7ulp-pinctrl.txt | 66 |
1 files changed, 29 insertions, 37 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7ulp-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7ulp-pinctrl.txt index 44ad670ae11e..bfa3703a7446 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7ulp-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7ulp-pinctrl.txt @@ -7,55 +7,47 @@ Note: This binding doc is only for the IOMUXC1 support in A7 Domain and it only supports generic pin config. -Please also refer pinctrl-bindings.txt in this directory for generic pinctrl -binding. - -=== Pin Controller Node === +Please refer to fsl,imx-pinctrl.txt in this directory for common binding +part and usage. Required properties: -- compatible: "fsl,imx7ulp-iomuxc1" -- reg: Should contain the base physical address and size of the iomuxc - registers. - -=== Pin Configuration Node === -- pinmux: One integers array, represents a group of pins mux setting. - The format is pinmux = <PIN_FUNC_ID>, PIN_FUNC_ID is a pin working on - a specific function. - - NOTE: i.MX7ULP PIN_FUNC_ID consists of 4 integers as it shares one mux - and config register as follows: - <mux_conf_reg input_reg mux_mode input_val> - - Refer to imx7ulp-pinfunc.h in in device tree source folder for all - available imx7ulp PIN_FUNC_ID. - -Optional Properties: -- drive-strength Integer. Controls Drive Strength - 0: Standard - 1: Hi Driver -- drive-push-pull Bool. Enable Pin Push-pull -- drive-open-drain Bool. Enable Pin Open-drian -- slew-rate: Integer. Controls Slew Rate - 0: Standard - 1: Slow -- bias-disable: Bool. Pull disabled -- bias-pull-down: Bool. Pull down on pin -- bias-pull-up: Bool. Pull up on pin +- compatible: "fsl,imx7ulp-iomuxc1". +- fsl,pins: Each entry consists of 5 integers which represents the mux + and config setting for one pin. The first 4 integers + <mux_conf_reg input_reg mux_mode input_val> are specified + using a PIN_FUNC_ID macro, which can be found in + imx7ulp-pinfunc.h in the device tree source folder. + The last integer CONFIG is the pad setting value like + pull-up on this pin. + + Please refer to i.MX7ULP Reference Manual for detailed + CONFIG settings. + +CONFIG bits definition: +PAD_CTL_OBE (1 << 17) +PAD_CTL_IBE (1 << 16) +PAD_CTL_LK (1 << 16) +PAD_CTL_DSE_HI (1 << 6) +PAD_CTL_DSE_STD (0 << 6) +PAD_CTL_ODE (1 << 5) +PAD_CTL_PUSH_PULL (0 << 5) +PAD_CTL_SRE_SLOW (1 << 2) +PAD_CTL_SRE_STD (0 << 2) +PAD_CTL_PE (1 << 0) Examples: #include "imx7ulp-pinfunc.h" /* Pin Controller Node */ -iomuxc1: iomuxc@40ac0000 { +iomuxc1: pinctrl@40ac0000 { compatible = "fsl,imx7ulp-iomuxc1"; reg = <0x40ac0000 0x1000>; /* Pin Configuration Node */ pinctrl_lpuart4: lpuart4grp { - pinmux = < - IMX7ULP_PAD_PTC3__LPUART4_RX - IMX7ULP_PAD_PTC2__LPUART4_TX + fsl,pins = < + IMX7ULP_PAD_PTC3__LPUART4_RX 0x1 + IMX7ULP_PAD_PTC2__LPUART4_TX 0x1 >; - bias-pull-up; }; }; |