diff options
author | Olof Johansson <olof@lixom.net> | 2016-02-01 12:22:52 -0800 |
---|---|---|
committer | Olof Johansson <olof@lixom.net> | 2016-02-01 12:22:52 -0800 |
commit | 7f7420f07ee2161e09e305e2d8a41069c3612942 (patch) | |
tree | 0d1819ff2be9fa372d5c251f9d2e70bdd0fc4fac /arch | |
parent | b83132f76225fa2e61771ef999a884d02c2217fd (diff) | |
parent | ab342c77fa60a30fce4d4228f88fd1b7bf566055 (diff) |
Merge tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps with the most intrusive stuff being read-only data
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
* tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: Fix wl12xx missing clocks that cause hangs
ARM: OMAP: Add PWM dmtimer platform data quirks
ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules
ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata
ARM: OMAP2+: Fix l2_inv_api_params for rodata
ARM: OMAP2+: Fix save_secure_ram_context for rodata
ARM: OMAP2+: Fix l2dis_3630 for rodata
ARM: OMAP2+: Fix wait_dll_lock_timed for rodata
ARM: OMAP2+: Remove legacy mailbox device instantiation
ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox
ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Diffstat (limited to 'arch')
-rw-r--r-- | arch/arm/boot/dts/am33xx.dtsi | 1 | ||||
-rw-r--r-- | arch/arm/boot/dts/am4372.dtsi | 5 | ||||
-rw-r--r-- | arch/arm/boot/dts/am437x-gp-evm.dts | 4 | ||||
-rw-r--r-- | arch/arm/boot/dts/am43x-epos-evm.dts | 2 | ||||
-rw-r--r-- | arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 12 | ||||
-rw-r--r-- | arch/arm/boot/dts/am57xx-sbc-am57x.dts | 8 | ||||
-rw-r--r-- | arch/arm/boot/dts/logicpd-torpedo-som.dtsi | 9 | ||||
-rw-r--r-- | arch/arm/boot/dts/omap5-board-common.dtsi | 33 | ||||
-rw-r--r-- | arch/arm/configs/omap2plus_defconfig | 10 | ||||
-rw-r--r-- | arch/arm/mach-omap2/devices.c | 28 | ||||
-rw-r--r-- | arch/arm/mach-omap2/pdata-quirks.c | 23 | ||||
-rw-r--r-- | arch/arm/mach-omap2/sleep34xx.S | 61 | ||||
-rw-r--r-- | arch/arm/mach-omap2/sleep44xx.S | 25 |
13 files changed, 130 insertions, 91 deletions
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index 04885f9f959e..1fafaad516ba 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -439,6 +439,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <8>; mbox_wkupm3: wkup_m3 { + ti,mbox-send-noirq; ti,mbox-tx = <0 0 0>; ti,mbox-rx = <0 0 3>; }; diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index df955ba4dc62..92068fbf8b57 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -73,7 +73,7 @@ global_timer: timer@48240200 { compatible = "arm,cortex-a9-global-timer"; reg = <0x48240200 0x100>; - interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>; interrupt-parent = <&gic>; clocks = <&mpu_periphclk>; }; @@ -81,7 +81,7 @@ local_timer: timer@48240600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0x48240600 0x100>; - interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_PPI 13 IRQ_TYPE_EDGE_RISING>; interrupt-parent = <&gic>; clocks = <&mpu_periphclk>; }; @@ -290,6 +290,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <8>; mbox_wkupm3: wkup_m3 { + ti,mbox-send-noirq; ti,mbox-tx = <0 0 0>; ti,mbox-rx = <0 0 3>; }; diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts index 64d43325bcbc..ecd09ab6d581 100644 --- a/arch/arm/boot/dts/am437x-gp-evm.dts +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -590,8 +590,6 @@ pinctrl-names = "default"; pinctrl-0 = <&pixcir_ts_pins>; reg = <0x5c>; - interrupt-parent = <&gpio3>; - interrupts = <22 0>; attb-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; @@ -599,7 +597,7 @@ * 0x264 represents the offset of padconf register of * gpio3_22 from am43xx_pinmux base. */ - interrupts-extended = <&gpio3 22 IRQ_TYPE_NONE>, + interrupts-extended = <&gpio3 22 IRQ_TYPE_EDGE_FALLING>, <&am43xx_pinmux 0x264>; interrupt-names = "tsc", "wakeup"; diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index 746fd2b17958..d580e2b70f9a 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -491,7 +491,7 @@ pinctrl-0 = <&pixcir_ts_pins>; reg = <0x5c>; interrupt-parent = <&gpio1>; - interrupts = <17 0>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>; diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index c53882643ae9..8d93882dc8d5 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -167,7 +167,7 @@ DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ - DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT_PULLUP | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ + DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ >; }; @@ -492,14 +492,14 @@ pinctrl-names = "default"; pinctrl-0 = <&qspi1_pins>; - spi-max-frequency = <20000000>; + spi-max-frequency = <48000000>; spi_flash: spi_flash@0 { #address-cells = <1>; #size-cells = <1>; compatible = "spansion,m25p80", "jedec,spi-nor"; reg = <0>; /* CS0 */ - spi-max-frequency = <20000000>; + spi-max-frequency = <48000000>; partition@0 { label = "uboot"; @@ -559,13 +559,13 @@ &cpsw_emac0 { phy_id = <&davinci_mdio>, <0>; - phy-mode = "rgmii"; + phy-mode = "rgmii-txid"; dual_emac_res_vlan = <0>; }; &cpsw_emac1 { phy_id = <&davinci_mdio>, <1>; - phy-mode = "rgmii"; + phy-mode = "rgmii-txid"; dual_emac_res_vlan = <1>; }; @@ -588,7 +588,7 @@ }; &usb2 { - dr_mode = "peripheral"; + dr_mode = "host"; }; &mcasp3 { diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts index 77bb8e17401a..988e99632d49 100644 --- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts +++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts @@ -25,8 +25,8 @@ &dra7_pmx_core { uart3_pins_default: uart3_pins_default { pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */ - DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */ + DRA7XX_CORE_IOPAD(0x3648, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */ + DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */ >; }; @@ -108,9 +108,9 @@ pinctrl-0 = <&i2c5_pins_default>; clock-frequency = <400000>; - eeprom_base: atmel@50 { + eeprom_base: atmel@54 { compatible = "atmel,24c08"; - reg = <0x50>; + reg = <0x54>; pagesize = <16>; }; diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi index 7fed0bd4f3de..00805322367e 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi @@ -112,14 +112,6 @@ clock-frequency = <400000>; }; -&i2c2 { - clock-frequency = <400000>; -}; - -&i2c3 { - clock-frequency = <400000>; -}; - /* * Only found on the wireless SOM. For the SOM without wireless, the pins for * MMC3 can be routed with jumpers to the second MMC slot on the devkit and @@ -143,6 +135,7 @@ interrupt-parent = <&gpio5>; interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */ ref-clock-frequency = <26000000>; + tcxo-clock-frequency = <26000000>; }; }; diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi index 888412c63f97..902657d6713b 100644 --- a/arch/arm/boot/dts/omap5-board-common.dtsi +++ b/arch/arm/boot/dts/omap5-board-common.dtsi @@ -130,6 +130,16 @@ }; }; +&gpio8 { + /* TI trees use GPIO instead of msecure, see also muxing */ + p234 { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "gpio8_234/msecure"; + }; +}; + &omap5_pmx_core { pinctrl-names = "default"; pinctrl-0 = < @@ -213,6 +223,13 @@ >; }; + /* TI trees use GPIO mode; msecure mode does not work reliably? */ + palmas_msecure_pins: palmas_msecure_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */ + >; + }; + usbhost_pins: pinmux_usbhost_pins { pinctrl-single,pins = < OMAP5_IOPAD(0x0c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ @@ -278,6 +295,12 @@ &usbhost_wkup_pins >; + palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1 */ + >; + }; + usbhost_wkup_pins: pinmux_usbhost_wkup_pins { pinctrl-single,pins = < OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ @@ -345,6 +368,8 @@ interrupt-controller; #interrupt-cells = <2>; ti,system-power-controller; + pinctrl-names = "default"; + pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>; extcon_usb3: palmas_usb { compatible = "ti,palmas-usb-vid"; @@ -358,6 +383,14 @@ #clock-cells = <0>; }; + rtc { + compatible = "ti,palmas-rtc"; + interrupt-parent = <&palmas>; + interrupts = <8 IRQ_TYPE_NONE>; + ti,backup-battery-chargeable; + ti,backup-battery-charge-high-current; + }; + palmas_pmic { compatible = "ti,palmas-pmic"; interrupt-parent = <&palmas>; diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index c5e1943e5427..a7151744b85c 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -50,6 +50,7 @@ CONFIG_SOC_AM33XX=y CONFIG_SOC_AM43XX=y CONFIG_SOC_DRA7XX=y CONFIG_ARM_THUMBEE=y +CONFIG_ARM_KERNMEM_PERMS=y CONFIG_ARM_ERRATA_411920=y CONFIG_ARM_ERRATA_430973=y CONFIG_SMP=y @@ -177,6 +178,7 @@ CONFIG_TI_CPTS=y CONFIG_AT803X_PHY=y CONFIG_SMSC_PHY=y CONFIG_USB_USBNET=m +CONFIG_USB_NET_SMSC75XX=m CONFIG_USB_NET_SMSC95XX=m CONFIG_USB_ALI_M5632=y CONFIG_USB_AN2720=y @@ -354,6 +356,11 @@ CONFIG_USB_MUSB_DSPS=m CONFIG_USB_INVENTRA_DMA=y CONFIG_USB_TI_CPPI41_DMA=y CONFIG_USB_DWC3=m +CONFIG_USB_SERIAL=m +CONFIG_USB_SERIAL_GENERIC=y +CONFIG_USB_SERIAL_SIMPLE=m +CONFIG_USB_SERIAL_FTDI_SIO=m +CONFIG_USB_SERIAL_PL2303=m CONFIG_USB_TEST=m CONFIG_AM335X_PHY_USB=y CONFIG_USB_GADGET=m @@ -387,6 +394,7 @@ CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=m CONFIG_LEDS_GPIO=m CONFIG_LEDS_PWM=m +CONFIG_LEDS_PCA963X=m CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=m CONFIG_LEDS_TRIGGER_ONESHOT=m @@ -449,6 +457,8 @@ CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ISO8859_1=y CONFIG_PRINTK_TIME=y CONFIG_DEBUG_INFO=y +CONFIG_DEBUG_INFO_SPLIT=y +CONFIG_DEBUG_INFO_DWARF4=y CONFIG_MAGIC_SYSRQ=y CONFIG_SCHEDSTATS=y CONFIG_TIMER_STATS=y diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c index 9cda974a3009..d7f1d69daf6d 100644 --- a/arch/arm/mach-omap2/devices.c +++ b/arch/arm/mach-omap2/devices.c @@ -18,7 +18,6 @@ #include <linux/slab.h> #include <linux/of.h> #include <linux/pinctrl/machine.h> -#include <linux/platform_data/mailbox-omap.h> #include <asm/mach-types.h> #include <asm/mach/map.h> @@ -66,32 +65,6 @@ static int __init omap3_l3_init(void) } omap_postcore_initcall(omap3_l3_init); -#if defined(CONFIG_OMAP2PLUS_MBOX) || defined(CONFIG_OMAP2PLUS_MBOX_MODULE) -static inline void __init omap_init_mbox(void) -{ - struct omap_hwmod *oh; - struct platform_device *pdev; - struct omap_mbox_pdata *pdata; - - oh = omap_hwmod_lookup("mailbox"); - if (!oh) { - pr_err("%s: unable to find hwmod\n", __func__); - return; - } - if (!oh->dev_attr) { - pr_err("%s: hwmod doesn't have valid attrs\n", __func__); - return; - } - - pdata = (struct omap_mbox_pdata *)oh->dev_attr; - pdev = omap_device_build("omap-mailbox", -1, oh, pdata, sizeof(*pdata)); - WARN(IS_ERR(pdev), "%s: could not build device, err %ld\n", - __func__, PTR_ERR(pdev)); -} -#else -static inline void omap_init_mbox(void) { } -#endif /* CONFIG_OMAP2PLUS_MBOX */ - static inline void omap_init_sti(void) {} #if defined(CONFIG_SPI_OMAP24XX) || defined(CONFIG_SPI_OMAP24XX_MODULE) @@ -229,7 +202,6 @@ static int __init omap2_init_devices(void) * please keep these calls, and their implementations above, * in alphabetical order so they're easier to sort through. */ - omap_init_mbox(); omap_init_mcspi(); omap_init_sham(); omap_init_aes(); diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c index e781e4fae13a..a935d28443da 100644 --- a/arch/arm/mach-omap2/pdata-quirks.c +++ b/arch/arm/mach-omap2/pdata-quirks.c @@ -23,6 +23,8 @@ #include <linux/platform_data/pinctrl-single.h> #include <linux/platform_data/iommu-omap.h> #include <linux/platform_data/wkup_m3.h> +#include <linux/platform_data/pwm_omap_dmtimer.h> +#include <plat/dmtimer.h> #include "common.h" #include "common-board-devices.h" @@ -449,6 +451,24 @@ void omap_auxdata_legacy_init(struct device *dev) dev->platform_data = &twl_gpio_auxdata; } +/* Dual mode timer PWM callbacks platdata */ +#if IS_ENABLED(CONFIG_OMAP_DM_TIMER) +struct pwm_omap_dmtimer_pdata pwm_dmtimer_pdata = { + .request_by_node = omap_dm_timer_request_by_node, + .free = omap_dm_timer_free, + .enable = omap_dm_timer_enable, + .disable = omap_dm_timer_disable, + .get_fclk = omap_dm_timer_get_fclk, + .start = omap_dm_timer_start, + .stop = omap_dm_timer_stop, + .set_load = omap_dm_timer_set_load, + .set_match = omap_dm_timer_set_match, + .set_pwm = omap_dm_timer_set_pwm, + .set_prescaler = omap_dm_timer_set_prescaler, + .write_counter = omap_dm_timer_write_counter, +}; +#endif + /* * Few boards still need auxdata populated before we populate * the dev entries in of_platform_populate(). @@ -502,6 +522,9 @@ static struct of_dev_auxdata omap_auxdata_lookup[] __initdata = { OF_DEV_AUXDATA("ti,am4372-wkup-m3", 0x44d00000, "44d00000.wkup_m3", &wkup_m3_data), #endif +#if IS_ENABLED(CONFIG_OMAP_DM_TIMER) + OF_DEV_AUXDATA("ti,omap-dmtimer-pwm", 0, NULL, &pwm_dmtimer_pdata), +#endif #if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) OF_DEV_AUXDATA("ti,omap4-iommu", 0x4a066000, "4a066000.mmu", &omap4_iommu_pdata), diff --git a/arch/arm/mach-omap2/sleep34xx.S b/arch/arm/mach-omap2/sleep34xx.S index eafd120b53f1..1b9f0520dea9 100644 --- a/arch/arm/mach-omap2/sleep34xx.S +++ b/arch/arm/mach-omap2/sleep34xx.S @@ -86,13 +86,18 @@ ENTRY(enable_omap3630_toggle_l2_on_restore) stmfd sp!, {lr} @ save registers on stack /* Setup so that we will disable and enable l2 */ mov r1, #0x1 - adrl r2, l2dis_3630 @ may be too distant for plain adr - str r1, [r2] + adrl r3, l2dis_3630_offset @ may be too distant for plain adr + ldr r2, [r3] @ value for offset + str r1, [r2, r3] @ write to l2dis_3630 ldmfd sp!, {pc} @ restore regs and return ENDPROC(enable_omap3630_toggle_l2_on_restore) - .text -/* Function to call rom code to save secure ram context */ +/* + * Function to call rom code to save secure ram context. This gets + * relocated to SRAM, so it can be all in .data section. Otherwise + * we need to initialize api_params separately. + */ + .data .align 3 ENTRY(save_secure_ram_context) stmfd sp!, {r4 - r11, lr} @ save registers on stack @@ -126,6 +131,8 @@ ENDPROC(save_secure_ram_context) ENTRY(save_secure_ram_context_sz) .word . - save_secure_ram_context + .text + /* * ====================== * == Idle entry point == @@ -289,12 +296,6 @@ wait_sdrc_ready: bic r5, r5, #0x40 str r5, [r4] -/* - * PC-relative stores lead to undefined behaviour in Thumb-2: use a r7 as a - * base instead. - * Be careful not to clobber r7 when maintaing this code. - */ - is_dll_in_lock_mode: /* Is dll in lock mode? */ ldr r4, sdrc_dlla_ctrl @@ -302,11 +303,7 @@ is_dll_in_lock_mode: tst r5, #0x4 bne exit_nonoff_modes @ Return if locked /* wait till dll locks */ - adr r7, kick_counter wait_dll_lock_timed: - ldr r4, wait_dll_lock_counter - add r4, r4, #1 - str r4, [r7, #wait_dll_lock_counter - kick_counter] ldr r4, sdrc_dlla_status /* Wait 20uS for lock */ mov r6, #8 @@ -330,9 +327,6 @@ kick_dll: orr r6, r6, #(1<<3) @ enable dll str r6, [r4] dsb - ldr r4, kick_counter - add r4, r4, #1 - str r4, [r7] @ kick_counter b wait_dll_lock_timed exit_nonoff_modes: @@ -360,15 +354,6 @@ sdrc_dlla_status: .word SDRC_DLLA_STATUS_V sdrc_dlla_ctrl: .word SDRC_DLLA_CTRL_V - /* - * When exporting to userspace while the counters are in SRAM, - * these 2 words need to be at the end to facilitate retrival! - */ -kick_counter: - .word 0 -wait_dll_lock_counter: - .word 0 - ENTRY(omap3_do_wfi_sz) .word . - omap3_do_wfi @@ -437,7 +422,9 @@ ENTRY(omap3_restore) cmp r2, #0x0 @ Check if target power state was OFF or RET bne logic_l1_restore - ldr r0, l2dis_3630 + adr r1, l2dis_3630_offset @ address for offset + ldr r0, [r1] @ value for offset + ldr r0, [r1, r0] @ value at l2dis_3630 cmp r0, #0x1 @ should we disable L2 on 3630? bne skipl2dis mrc p15, 0, r0, c1, c0, 1 @@ -449,12 +436,14 @@ skipl2dis: and r1, #0x700 cmp r1, #0x300 beq l2_inv_gp + adr r0, l2_inv_api_params_offset + ldr r3, [r0] + add r3, r3, r0 @ r3 points to dummy parameters mov r0, #40 @ set service ID for PPA mov r12, r0 @ copy secure Service ID in r12 mov r1, #0 @ set task id for ROM code in r1 mov r2, #4 @ set some flags in r2, r6 mov r6, #0xff - adr r3, l2_inv_api_params @ r3 points to dummy parameters dsb @ data write barrier dmb @ data memory barrier smc #1 @ call SMI monitor (smi #1) @@ -488,8 +477,8 @@ skipl2dis: b logic_l1_restore .align -l2_inv_api_params: - .word 0x1, 0x00 +l2_inv_api_params_offset: + .long l2_inv_api_params - . l2_inv_gp: /* Execute smi to invalidate L2 cache */ mov r12, #0x1 @ set up to invalidate L2 @@ -506,7 +495,9 @@ l2_inv_gp: mov r12, #0x2 smc #0 @ Call SMI monitor (smieq) logic_l1_restore: - ldr r1, l2dis_3630 + adr r0, l2dis_3630_offset @ adress for offset + ldr r1, [r0] @ value for offset + ldr r1, [r0, r1] @ value at l2dis_3630 cmp r1, #0x1 @ Test if L2 re-enable needed on 3630 bne skipl2reen mrc p15, 0, r1, c1, c0, 1 @@ -535,9 +526,17 @@ control_stat: .word CONTROL_STAT control_mem_rta: .word CONTROL_MEM_RTA_CTRL +l2dis_3630_offset: + .long l2dis_3630 - . + + .data l2dis_3630: .word 0 + .data +l2_inv_api_params: + .word 0x1, 0x00 + /* * Internal functions */ diff --git a/arch/arm/mach-omap2/sleep44xx.S b/arch/arm/mach-omap2/sleep44xx.S index 9b09d85d811a..c7a3b4aab4b5 100644 --- a/arch/arm/mach-omap2/sleep44xx.S +++ b/arch/arm/mach-omap2/sleep44xx.S @@ -29,12 +29,6 @@ dsb .endm -ppa_zero_params: - .word 0x0 - -ppa_por_params: - .word 1, 0 - #ifdef CONFIG_ARCH_OMAP4 /* @@ -266,7 +260,9 @@ ENTRY(omap4_cpu_resume) beq skip_ns_smp_enable ppa_actrl_retry: mov r0, #OMAP4_PPA_CPU_ACTRL_SMP_INDEX - adr r3, ppa_zero_params @ Pointer to parameters + adr r1, ppa_zero_params_offset + ldr r3, [r1] + add r3, r3, r1 @ Pointer to ppa_zero_params mov r1, #0x0 @ Process ID mov r2, #0x4 @ Flag mov r6, #0xff @@ -303,7 +299,9 @@ skip_ns_smp_enable: ldr r0, =OMAP4_PPA_L2_POR_INDEX ldr r1, =OMAP44XX_SAR_RAM_BASE ldr r4, [r1, #L2X0_PREFETCH_CTRL_OFFSET] - adr r3, ppa_por_params + adr r1, ppa_por_params_offset + ldr r3, [r1] + add r3, r3, r1 @ Pointer to ppa_por_params str r4, [r3, #0x04] mov r1, #0x0 @ Process ID mov r2, #0x4 @ Flag @@ -328,6 +326,8 @@ skip_l2en: #endif b cpu_resume @ Jump to generic resume +ppa_por_params_offset: + .long ppa_por_params - . ENDPROC(omap4_cpu_resume) #endif /* CONFIG_ARCH_OMAP4 */ @@ -380,4 +380,13 @@ ENTRY(omap_do_wfi) nop ldmfd sp!, {pc} +ppa_zero_params_offset: + .long ppa_zero_params - . ENDPROC(omap_do_wfi) + + .data +ppa_zero_params: + .word 0 + +ppa_por_params: + .word 1, 0 |