Age | Commit message (Collapse) | Author | Files | Lines |
|
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly as in ppp, we need to migrate the ISDN/PPP code to make use
of the sk_unattached_filter api in order to decouple having direct
filter structure access. By using sk_unattached_filter_{create,destroy},
we can allow for the possibility to jit compile filters for faster
filter verdicts as well.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: isdn4linux@listserv.isdn4linux.de
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are currently pch_gbe, cpts, and ixp4xx_eth drivers that open-code
and reimplement a BPF classifier for the PTP protocol. Since all of them
effectively do the very same thing and load the very same PTP/BPF filter,
we can just consolidate that code by introducing ptp_classify_raw() in
the time-stamping core framework which can be used in drivers.
As drivers get initialized after bootstrapping the core networking
subsystem, they can make use of ptp_insns wrapped through
ptp_classify_raw(), which allows to simplify and remove PTP classifier
setup code in drivers.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch migrates an open-coded sk_run_filter() implementation with
proper use of the BPF API, that is, sk_unattached_filter_create(). This
migration is needed, as we will be internally transforming the filter
to a different representation, and therefore needs to be decoupled.
It is okay to do so as skb_timestamping_init() is called during
initialization of the network stack in core initcall via sock_init().
This would effectively also allow for PTP filters to be jit compiled if
bpf_jit_enable is set.
For better readability, there are also some newlines introduced, also
ptp_classify.h is only in kernel space.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch basically does two things, i) removes the extern keyword
from the include/linux/filter.h file to be more consistent with the
rest of Joe's changes, and ii) moves filter accounting into the filter
core framework.
Filter accounting mainly done through sk_filter_{un,}charge() take
care of the case when sockets are being cloned through sk_clone_lock()
so that removal of the filter on one socket won't result in eviction
as it's still referenced by the other.
These functions actually belong to net/core/filter.c and not
include/net/sock.h as we want to keep all that in a central place.
It's also not in fast-path so uninlining them is fine and even allows
us to get rd of sk_filter_release_rcu()'s EXPORT_SYMBOL and a forward
declaration.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc92778080 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a jited flag into sk_filter struct in order to indicate
whether a filter is currently jited or not. The size of sk_filter is
not being expanded as the 32 bit 'len' member allows upper bits to be
reused since a filter can currently only grow as large as BPF_MAXINSNS.
Therefore, there's enough room also for other in future needed flags to
reuse 'len' field if necessary. The jited flag also allows for having
alternative interpreter functions running as currently, we can only
detect jit compiled filters by testing fp->bpf_func to not equal the
address of sk_run_filter().
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop taking the transmit lock when a network device has specified
NETIF_F_LLTX.
If no locks needed to trasnmit a packet this is the ideal scenario for
netpoll as all packets can be trasnmitted immediately.
Even if some locks are needed in ndo_start_xmit skipping any unnecessary
serialization is desirable for netpoll as it makes it more likely a
debugging packet may be trasnmitted immediately instead of being
deferred until later.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netpoll_rx_enable and netpoll_rx_disable functions have always
controlled polling the network drivers transmit and receive queues.
Rename them to netpoll_poll_enable and netpoll_poll_disable to make
their functionality clear.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The gfp parameter was added in:
commit 47be03a28cc6c80e3aa2b3e8ed6d960ff0c5c0af
Author: Amerigo Wang <amwang@redhat.com>
Date: Fri Aug 10 01:24:37 2012 +0000
netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup()
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason for the gfp parameter was removed in:
commit c4cdef9b7183159c23c7302aaf270d64c549f557
Author: dingtianhong <dingtianhong@huawei.com>
Date: Tue Jul 23 15:25:27 2013 +0800
bonding: don't call slave_xxx_netpoll under spinlocks
The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.
bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing else that calls __netpoll_setup or ndo_netpoll_setup
requires a gfp paramter, so remove the gfp parameter from both
of these functions making the code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers incorrectly assign vlan acceleration features to
vlan_features thus causing issues for Q-in-Q vlan configurations.
Warn the user of such cases.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb. However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers. That may not
always be the case. If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.
A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated. This way skb_mac_gso_segment
will correctly skip all mac headers.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dropping packets in __dev_queue_xmit() when transmit queue
is stopped (NIC TX ring buffer full or BQL limit reached) currently
outputs a syslog message.
It would be better to get a precise count of such events available in
netdevice stats so that monitoring tools can have a clue.
This extends the work done in caf586e5f23ce
("net: add a core netdev->rx_dropped counter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add implementation for the add/del vxlan port ndo calls, using the
CONFIG_DEV firmware command.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce the CONFIG_DEV firmware command which we will use to
configure the UDP port assumed by the firmware for the VXLAN offloads.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_zerocopy can copy elements of the frags array between skbs, but it doesn't
orphan them. Also, it doesn't handle errors, so this patch takes care of that
as well, and modify the callers accordingly. skb_tx_error() is also added to
the callers so they will signal the failed delivery towards the creator of the
skb.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a race which happens by freeing an object on the stack.
Quoting Julius:
> The issue is
> that it calls usbnet_terminate_urbs() before that, which temporarily
> installs a waitqueue in dev->wait in order to be able to wait on the
> tasklet to run and finish up some queues. The waiting itself looks
> okay, but the access to 'dev->wait' is totally unprotected and can
> race arbitrarily. I think in this case usbnet_bh() managed to succeed
> it's dev->wait check just before usbnet_terminate_urbs() sets it back
> to NULL. The latter then finishes and the waitqueue_t structure on its
> stack gets overwritten by other functions halfway through the
> wake_up() call in usbnet_bh().
The fix is to just not allocate the data structure on the stack.
As dev->wait is abused as a flag it also takes a runtime PM change
to fix this bug.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Grant Grundler <grundler@google.com>
Tested-by: Grant Grundler <grundler@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for Samsung 10Gb ethernet driver(sxgbe).
- sxgbe core initialization
- Tx and Rx support
- MDIO support
- ISRs for Tx and Rx
- ifconfig support to driver
Signed-off-by: Siva Reddy Kallam <siva.kallam@samsung.com>
Signed-off-by: Vipul Pandya <vipul.pandya@samsung.com>
Signed-off-by: Girish K S <ks.giri@samsung.com>
Neatening-by: Joe Perches <joe@perches.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vlan support 2 proto: 802.1q and 802.1ad, so make a new function
called vlan_dev_vlan_proto() which could return the vlan proto for
input dev.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The packet hash can be considered a property of the packet, not just
on RX path.
This patch changes name of rxhash and l4_rxhash skbuff fields to be
hash and l4_hash respectively. This includes changing uses of the
field in the code which don't call the access functions.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
Please pull this batch of wireless updates intended for 3.15!
For the mac80211 bits, Johannes says:
"This has a whole bunch of bugfixes for things that went into -next
previously as well as some other bugfixes I didn't want to rush into
3.14 at this point. The rest of it is some cleanups and a few small
features, the biggest of which is probably Janusz's regulatory DFS CAC
time code."
For the Bluetooth bits, Gustavo says:
"One more pull request to 3.15. This is mostly and bug fix pull request, it
contains several fixes and clean up all over the tree, plus some small new
features."
For the NFC bits, Samuel says:
"This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande."
For the iwlwifi bits, Emmanuel says:
"We were sending a host command while the mutex wasn't held. This
led to hard-to-catch races."
And...
"I have a fix for a "merge damage" which is not really a merge
damage: it enables scheduled scan which has been disabled in
wireless.git. Since you merged wireless.git into wireless-next.git,
this can now be fixed in wireless-next.git.
Besides this, Alex made a workaround for a hardware bug. This fix
allows us to consume less power in S3. Arik and Eliad continue to
work on D0i3 which is a run-time power saving feature. Eliad also
contributes a few bits to the rate scaling logic to which Eyal adds his
own contribution. Avri dives deep in the power code - newer firmware
will allow to enable power save in newer scenarios. Johannes made a few
clean-ups. I have the regular amount of BT Coex boring stuff. I disable
uAPSD since we identified firmware bugs that cause packet loss. One
thing that do stand out is the udev event that we now send when the
FW asserts. I hope it will allow us to debug the FW more easily."
Also included is one last iwlwifi pull for a build breakage fix...
For the Atheros bits, Kalle says:
"Michal now did some optimisations and was able to improve throughput by
100 Mbps on our MIPS based AP135 platform. Chun-Yeow added some
workarounds to be able to better use ad-hoc mode. Ben improved log
messages and added support for MSDU chaining. And, as usual, also some
smaller fixes."
Beyond that...
Andrea Merello continues his rtl8180 refactoring, in preparation for
a long-awaited rtl8187 driver. We get a new driver (rsi) for the
RS9113 chip, from Fariya Fatima. And, of course, we get the usual
round of updates for ath9k, brcmfmac, mwifiex, wil6210, etc. as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace kfree_skb with dev_kfree_skb_any in vlan_insert_tag as
vlan_insert_tag can be called from hard irq context (netpoll)
and from other contexts.
dev_kfree_skb_any is used as vlan_insert_tag only frees the skb if the
skb can not be modified to insert a tag, in which case vlan_insert_tag
drops the skb.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Pull networking fixes from David Miller:
1) OpenVswitch's lookup_datapath() returns error pointers, so don't
check against NULL. From Jiri Pirko.
2) pfkey_compile_policy() code path tries to do a GFP_KERNEL allocation
under RCU locks, fix by using GFP_ATOMIC when necessary. From
Nikolay Aleksandrov.
3) phy_suspend() indirectly passes uninitialized data into the ethtool
get wake-on-land implementations. Fix from Sebastian Hesselbarth.
4) CPSW driver unregisters CPTS twice, fix from Benedikt Spranger.
5) If SKB allocation of reply packet fails, vxlan's arp_reduce() defers
a NULL pointer. Fix from David Stevens.
6) IPV6 neigh handling in vxlan doesn't validate the destination
address properly, and it builds a packet with the src and dst
reversed. Fix also from David Stevens.
7) Fix spinlock recursion during subscription failures in TIPC stack,
from Erik Hugne.
8) Revert buggy conversion of davinci_emac to devm_request_irq, from
Chrstian Riesch.
9) Wrong flags passed into forwarding database netlink notifications,
from Nicolas Dichtel.
10) The netpoll neighbour soliciation handler checks wrong ethertype,
needs to be ETH_P_IPV6 rather than ETH_P_ARP. Fix from Li RongQing.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
tipc: fix spinlock recursion bug for failed subscriptions
vxlan: fix nonfunctional neigh_reduce()
net: davinci_emac: Fix rollback of emac_dev_open()
net: davinci_emac: Replace devm_request_irq with request_irq
netpoll: fix the skb check in pkt_is_ns
net: micrel : ks8851-ml: add vdd-supply support
ip6mr: fix mfc notification flags
ipmr: fix mfc notification flags
rtnetlink: fix fdb notification flags
tcp: syncookies: do not use getnstimeofday()
netlink: fix setsockopt in mmap examples in documentation
openvswitch: Correctly report flow used times for first 5 minutes after boot.
via-rhine: Disable device in error path
ATHEROS-ATL1E: Convert iounmap to pci_iounmap
vxlan: fix potential NULL dereference in arp_reduce()
cnic: Update version to 2.5.20 and copyright year.
cnic,bnx2i,bnx2fc: Fix inconsistent use of page size
cnic: Use proper ulp_ops for per device operations.
net: cdc_ncm: fix control message ordering
ipv6: ip6_append_data_mtu do not handle the mtu of the second fragment properly
...
|
|
This patch adds a pair of new ioctls to the PTP Hardware Clock device
interface. Using the ioctls, user space programs can query each pin to
find out its current function and also reprogram a different function
if desired.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull trace fix from Steven Rostedt:
"Vaibhav Nagarnaik discovered that since 3.10 a clean-up patch made the
array index in the trace event format bogus.
He supplied an elegant solution that uses __stringify() and also
removes the need for the event_storage and event_storage_mutex and
also cuts off a few K of overhead from the trace events"
* tag 'trace-fixes-v3.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix array size mismatch in format string
|
|
Add remove_linear_migration_ptes_from_nonlinear(), to fix an interesting
little include/linux/swapops.h:131 BUG_ON(!PageLocked) found by trinity:
indicating that remove_migration_ptes() failed to find one of the
migration entries that was temporarily inserted.
The problem comes from remap_file_pages()'s switch from vma_interval_tree
(good for inserting the migration entry) to i_mmap_nonlinear list (no good
for locating it again); but can only be a problem if the remap_file_pages()
range does not cover the whole of the vma (zap_pte() clears the range).
remove_migration_ptes() needs a file_nonlinear method to go down the
i_mmap_nonlinear list, applying linear location to look for migration
entries in those vmas too, just in case there was this race.
The file_nonlinear method does need rmap_walk_control.arg to do this;
but it never needed vma passed in - vma comes from its own iteration.
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Reported-and-tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
According to "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF, the wMTU field of the MBIM extended
functional descriptor indicates the operator preferred MTU for IP data
streams.
This patch modifies cdc_ncm_setup to ensure that the MTU value set on
the usbnet device does not exceed the operator preferred MTU indicated
by wMTU if the MBIM device exposes a MBIM extended functional
descriptor.
Signed-off-by: Ben Chan <benchan@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
In wrapped commands, we need to verify and convert
the slave's port into the real physical port.
Furthermore, when sending the response back to the slave,
a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
The slave assumes that sqpn is used for QP1 communication.
If the slave is assigned to a port != (first port), we need
to adjust the sqpn that will direct its QP1 packets into the
correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
In B0 steering, gid[5] contains the port. It needs
to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
When a slave queries the hardware, it needs to view only
the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
The QP port is encoded in the sched_qp, thus in modify_qp we need
to encode the correct port in sched_qp.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds the required data structures to support VFs with N (1 or 2)
ports instead of always using the number of physical ports.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In event format strings, the array size is reported in two locations.
One in array subscript and then via the "size:" attribute. The values
reported there have a mismatch.
For e.g., in sched:sched_switch the prev_comm and next_comm character
arrays have subscript values as [32] where as the actual field size is
16.
name: sched_switch
ID: 301
format:
field:unsigned short common_type; offset:0; size:2; signed:0;
field:unsigned char common_flags; offset:2; size:1; signed:0;
field:unsigned char common_preempt_count; offset:3; size:1;signed:0;
field:int common_pid; offset:4; size:4; signed:1;
field:char prev_comm[32]; offset:8; size:16; signed:1;
field:pid_t prev_pid; offset:24; size:4; signed:1;
field:int prev_prio; offset:28; size:4; signed:1;
field:long prev_state; offset:32; size:8; signed:1;
field:char next_comm[32]; offset:40; size:16; signed:1;
field:pid_t next_pid; offset:56; size:4; signed:1;
field:int next_prio; offset:60; size:4; signed:1;
After bisection, the following commit was blamed:
92edca0 tracing: Use direct field, type and system names
This commit removes the duplication of strings for field->name and
field->type assuming that all the strings passed in
__trace_define_field() are immutable. This is not true for arrays, where
the type string is created in event_storage variable and field->type for
all array fields points to event_storage.
Use __stringify() to create a string constant for the type string.
Also, get rid of event_storage and event_storage_mutex that are not
needed anymore.
also, an added benefit is that this reduces the overhead of events a bit more:
text data bss dec hex filename
8424787 2036472 1302528 11763787 b3804b vmlinux
8420814 2036408 1302528 11759750 b37086 vmlinux.patched
Link: http://lkml.kernel.org/r/1392349908-29685-1-git-send-email-vnagarnaik@google.com
Cc: Laurent Chavey <chavey@google.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Vaibhav Nagarnaik <vnagarnaik@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
In the 802.11ad, aka DMG (Dynamic Multi-Gigabit), aka 60Ghz
spec, maximum MSDU size extended to 7920 bytes.
add #define for this.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is a context modified revert of commit 6a9612e2cb22
("net: cdc_ncm: remove ncm_parm field") which introduced
a NCM specification violation, causing setup errors for
some devices. These errors resulted in the device and
host disagreeing about shared settings, with complete
failure to communicate as the end result.
The NCM specification require that many of the NCM specific
control reuests are sent only while the NCM Data Interface
is in alternate setting 0. Reverting the commit ensures that
we follow this requirement.
Fixes: 6a9612e2cb22 ("net: cdc_ncm: remove ncm_parm field")
Reported-and-tested-by: Pasi Kärkkäinen <pasik@iki.fi>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
1) Fix a sleep in atomic when pfkey_sadb2xfrm_user_sec_ctx()
is called from pfkey_compile_policy().
Fix from Nikolay Aleksandrov.
2) security_xfrm_policy_alloc() can be called in process and atomic
context. Add an argument to let the callers choose the appropriate
way. Fix from Nikolay Aleksandrov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netpoll packet receive code only becomes active if the netpoll
rx_skb_hook is implemented, and there is not a single implementation
of the netpoll rx_skb_hook in the kernel.
All of the out of tree implementations I have found all call
netpoll_poll which was removed from the kernel in 2011, so this
change should not add any additional breakage.
There are problems with the netpoll packet receive code. __netpoll_rx
does not call dev_kfree_skb_irq or dev_kfree_skb_any in hard irq
context. netpoll_neigh_reply leaks every skb it receives. Reception
of packets does not work successfully on stacked devices (aka bonding,
team, bridge, and vlans).
Given that the netpoll packet receive code is buggy, there are no
out of tree users that will be merged soon, and the code has
not been used for in tree for a decade let's just remove it.
Reverting this commit can server as a starting point for anyone
who wants to resurrect netpoll packet reception support.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make rx_skb_hook, and rx in struct netpoll depend on
CONFIG_NETPOLL_TRAP Make rx_lock, rx_np, and neigh_tx in struct
netpoll_info depend on CONFIG_NETPOLL_TRAP
Make the functions netpoll_rx_on, netpoll_rx, and netpoll_receive_skb
no-ops when CONFIG_NETPOLL_TRAP is not set.
Only build netpoll_neigh_reply, checksum_udp service_neigh_queue,
pkt_is_ns, and __netpoll_rx when CONFIG_NETPOLL_TRAP is defined.
Add helper functions netpoll_trap_setup, netpoll_trap_setup_info,
netpoll_trap_cleanup, and netpoll_trap_cleanup_info that initialize
and cleanup the struct netpoll and struct netpoll_info receive
specific fields when CONFIG_NETPOLL_TRAP is enabled and do nothing
otherwise.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we no longer need to receive packets to safely drain the
network drivers receive queue move netpoll_trap and netpoll_set_trap
under CONFIG_NETPOLL_TRAP
Making netpoll_trap and netpoll_set_trap noop inline functions
when CONFIG_NETPOLL_TRAP is not set.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the strategy of netpoll from dropping all packets received
during netpoll_poll_dev to calling napi poll with a budget of 0
(to avoid processing drivers rx queue), and to ignore packets received
with netif_rx (those will safely be placed on the backlog queue).
All of the netpoll supporting drivers have been reviewed to ensure
either thay use netif_rx or that a budget of 0 is supported by their
napi poll routine and that a budget of 0 will not process the drivers
rx queues.
Not dropping packets makes NETPOLL_RX_DROP unnecesary so it is removed.
npinfo->rx_flags is removed as rx_flags with just the NETPOLL_RX_ENABLED
flag becomes just a redundant mirror of list_empty(&npinfo->rx_np).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper netpoll_rx_processing that reports when netpoll has
receive side processing to perform.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
most relevantly they are:
* cleanup to remove double semicolon from stephen hemminger.
* calm down sparse warning in xt_ipcomp, from Fan Du.
* nf_ct_labels support for nf_tables, from Florian Westphal.
* new macros to simplify rcu dereferences in the scope of nfnetlink
and nf_tables, from Patrick McHardy.
* Accept queue and drop (including reason for drop) to verdict
parsing in nf_tables, also from Patrick.
* Remove unused random seed initialization in nfnetlink_log, from
Florian Westphal.
* Allow to attach user-specific information to nf_tables rules, useful
to attach user comments to rule, from me.
* Return errors in ipset according to the manpage documentation, from
Jozsef Kadlecsik.
* Fix coccinelle warnings related to incorrect bool type usage for ipset,
from Fengguang Wu.
* Add hash:ip,mark set type to ipset, from Vytas Dauksa.
* Fix message for each spotted by ipset for each netns that is created,
from Ilia Mirkin.
* Add forceadd option to ipset, which evicts a random entry from the set
if it becomes full, from Josh Hunt.
* Minor IPVS cleanups and fixes from Andi Kleen and Tingwei Liu.
* Improve conntrack scalability by removing a central spinlock, original
work from Eric Dumazet. Jesper Dangaard Brouer took them over to address
remaining issues. Several patches to prepare this change come in first
place.
* Rework nft_hash to resolve bugs (leaking chain, missing rcu synchronization
on element removal, etc. from Patrick McHardy.
* Restore context in the rule deletion path, as we now release rule objects
synchronously, from Patrick McHardy. This gets back event notification for
anonymous sets.
* Fix NAT family validation in nft_nat, also from Patrick.
* Improve scalability of xt_connlimit by using an array of spinlocks and
by introducing a rb-tree of hashtables for faster lookup of accounted
objects per network. This patch was preceded by several patches and
refactorizations to accomodate this change including the use of kmem_cache,
from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BCM4354 is an a/b/g/n/ac 2x2 WiFi chip. This patch adds support for it through
SDIO interface.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
|
|
Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,
This is achieved as follows:
Outgoing MADs:
1. Source MAC: obtained from the CQ completion structure
(struct ib_wc, smac field).
2. Destination MAC: obtained from the tunnel header
3. vlan_id: obtained from the tunnel header.
Incoming MADs
1. The source (i.e., remote) MAC and vlan_id are passed in
the tunnel header to the proxy QP1.
VST mode support:
For outgoing MADs, the vlan_id obtained from the header is
discarded, and the vlan_id specified by the Hypervisor is used
instead.
For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
"invalid" vlan (0xffff) is substituted when forwarding to the slave.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs: Remaining GIDS are divided evenly between VFs activated by the driver.
If the division is not even, lower-numbered VFs get an extra GID.
For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|